SPL REPAIR TO CERTAIN BLDGS AND PROVN OF LED LIGHTS AT OLD CANTT ALLAHABAD

Amount

Excavation in trenches not exceeding 1.5m deep & not exceeding 1.5m wide or area not exceeding 10 Sqm on plan& depth not exceeding 1.5 m in soft/loose soil and getting out for foundation, trenches etc complete all as specified & directed.

Returning, filling in soils, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick. complete all as specified and directed.

Removing surplus excavated material (soils) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and directed.

Spreading of natural, clean and dry sand in trenches for cable cushioning (8 cm before laying the cable and and 15cm after laying the cable), including punning the sand upto 18cm thick and consolidated, complete all as specified and directed. NOTE: Punned thickness only shall be measured.

Well burnt bricks sub class B, old size trenches for cable protection all as specified and directed.

XLPE cable insulated screened metet PVC beded galvanised steel strip or wire armoured, elect power cable (Heavy Duty) 1100 Volts grade with stranded aluminium conductor of 4 core 25 Sqmm complete all as specified and directed.

GI pipe light grade 40 mm bore including all fittings such as bend tee complete all as specified and directed.

Ring made from 50mm dia MS pipe with supports of 1 mtr dia including cap suitable for fixing on the existing pole with locking arrangement with painting and fixing the flood lights complete all as specified and directed by Engr-in-Charge.

Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-55 (11 metres long), complete all as specified and directed.

Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31 (9.0 metres long), complete all as specified and directed.

Cement concrete 1:4:8, type D2 (40mm graded stone aggregate) in foundation for encasing the pole upto GL complete all as specified and directed.

Providing PCC(cast in situ) 1:3:6 type C1 (20mm graded stone aggregate) for plinth block/coping of pole complete all as specified and directed.

Painting of pole externally with one coat of black bituminous paint (upto planting depth) and above plinth block concrete collar with two coat of aluminium paint over a coat of red oxide primer including preparation of surface including painting of 30cm wide bands 3 Nos with synthetic enamel paint of appropriate colour in alternate layer upto the height of 1.5m above plinth block, complete all as specified and directed.

Writing letter or figures (Block Roman, Italic as Indian) with black synthetic enamel paint of approved shade not exceeding 5cm height including numbering of pole, complete all as specified and directed.

New generation energy saving & environment friendly long life versatile pressure die-cast aluminium IP66 LED flood light 200 Watts and 3 core PVC unsheathed copper wiring fitting to junction box etc including making necessary electric connection complete all as specified and directed. Make: Havells/Phillips/CG/Bajaj as approved.

ENDURACITYLINER NEO generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP66 LED street light fitting 70 Watts and 3 core PVC unsheathed copper wire fitting to MCB distribution box/socket points with casing caping/flexible steel hose pipe including making necessary electric connection complete all as directed. Make: Havells Cat No ENDURACITYLINERNEOSL70WLED757PASYBOTG or techno-commercially equivalent model in Phillips/ CG / Bajaj

Earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth of not less than 2.25m deep below ground level with the top edge of earth plate at a depth of not less than 1.5m below ground level connected to GI earth lead of 4mm dia by means of bolts, nuts, washers of galvanised iron or steel, GI earth wire shall be protected by 40mm dia GI pipe 'light grade', watering pipe 20mm dia GI pipe 'light grade', GI wire meshed funnel, alternate layer of charcoal and salt on all side to earth plate upto a thickness of 150mm, filling of black cotton soil in earth pit upto GL and connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber and mild steel angle iron frame 40 x 40 x 3 mmand 40mm thick pre-cast RCC cover (1:2:4), type B-1 (using 20mm graded crushed aggregate) mix with 8mm dia TMT bars @ 75mm c/c both ways, mild steel ahndle 12mm dia, etc complete all as shown in electrical plate No.3 connected to earthing test point, including testing on completion, complete all as speciifed and as directed.

Cable junction pole light box with connection terminals factory made of size not less than 205x255x112mm (outside dimension) with IP66 protection made out high quality of thermoplastic poly carbonate having 4 nos of 16/25 sqmm vibration proof terminals, weather proof, dust proof, rust proof, fire resisitance, cable entry threw multiple slots complete all as specified and directed. Make: Hensal/Sintex

Cable route indicator made of 15x15x6mm thick MS plate welded with 8mmx30cm long MS rod grouted in PCC block of size 0.2x0.2x0.3m and wiring with LT cable complete all as directed.

Demolition of Cement Concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc, laid bedded pointed in any mortarn of floor, including cement mortar bedding complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards / slabs / blankets, any thickness, including cover fillets, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding, removing rubbish off the premises complete all as specified and directed.

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Brickwork with fly ash bricks, old size straight or curved on plan exceeding 6m mean radius, built in CM 1:6, complete all as specified and directed.

Glazed coloured ceramic tiles in 450mm x 300mm x 6 to 7mm thick, in skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile including backing coat of 10mm thick in CM 1:4, complete all as specified and directed.

Joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting, dados, risers to steps, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 10mm thick screed bed in CM 1:4 complete all as specified and directed.

Cement concrete 1:2:4 type B-0 using 12.50 mm graded stone aggregate in floors, 25 mm thick, complete all as specified and directed.

Machine cut baroda Green marble stone slab 18 to 20 mm thick laid over Kitchen cooking platform in 15mm thick cement screed bed (1:4) laid and jointed in grey cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete and including nosing of the edges half round (Stone slab shall be fixed in two pieces), complete all as specified and directed.

Cement concrete 1:3:6, type C1 (using 20mm graded stone aggregate), in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at the length not exceeding 3 mtrs and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight, complete all as specified and directed.

Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces of walls, mixed with water proofing compound, finishing the surface even and smooth with out using exta cement, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately as supply only.

Rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of walls, finishing the surface even and smooth with out using exta cement, complete all as specified and directed.

Supply only integral water proofing compound.

Taking up or down steel tubing 15mm bore and connections, complete all as specified and directed.

Taking up or down steel tubing 20mm bore and connections, complete all as specified and directed.

Mild Steel tubes medium grade in any size or length galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 15mm dia, complete all as specified and directed.

Mild Steel tubes medium grade in any size or length galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 20mm dia, complete all as specified and directed.

Fixing only old 15mm dia bore steel tubing & connection in new or old position fixed to wall, ceiling or laid in floors including necessary cutting & making of new threads for fixing of new fitings such as elbows, tees, sockets, union, reducer, etc as required, complete all as specified and directed.

Fixing only old 20mm dia bore steel tubing & connection in new or old position fixed to wall, ceiling or laid in floors including necessary cutting & making of new threads for fixing of new fitings such as elbows, tees, sockets, union, reducer, etc as required, complete all as specified and directed.

Dismantling of PVC water tanks of capacity exceeding 250 litres but not exceeding 500 litres, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 500 litre capacity (ISI marked), double layered, hoisted and fixed in position including connecting up pipes, complete allas speciofied and directed.

Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, 20mm bore, in repair, complete all as specified and directed. (in repair)

Ball valve high pressure PTMT with epoxy coated aluminium rod and high density plastic ball secured for iron pipe of dia 20mm (minimum weight 210 gram) in repair complete all as specified and directed.

Stainless steel plate rack (utensil rack) of size (600 mm X 750 mm) and depth 250mm made with 0.63 mm thick stainless steel sheet provided with brass screw including necessary fittings, nut/bolts including taking down old u/s plate rack, complete all as specified and directed.

Soap dish, stainless steel, standard size, any type, fixed to plugs with chromium plated brass screws, fixed in repair, complete all as specifeid and directed.

UPVC (SWR) 75mm bore floor trap, plain with grating including jointing with solvent cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) in repair, complete all as specified and directed.

Kitchen sink with drainage board made of stainless steel 1mm thick with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed in repair complete all as specified and directed.

Tubular towel rail of brass chromium plated, 20mm dia, D type, 60cm long between flanges in repair complete all as specified and direcetd.

Angle valve cast of screwed down, high pressure, with crutch or butterfly handle, 15mm bore, for iron pipe or for unions, fixed in repair, complete all as specified and directed.

Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type, chromium plated with long shank and cup (concealed type), 15 mm bore, in repair, complete all as specified and directed.

Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, fancy type, chromium plated, 15 mm bore, in repair, complete all as specified and directed.

Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), in repair, complete all as specified and directed.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe15mm bore, fancy type, in repair, complete all as specified and directed.

Brass chromium plated shower rose fancy type with arm, in repair, complete all as specified and directed.

Cast iron sanitary connection socket to fit WC out-let 100mm dia, in fixed in repair, complete all as specified and directed.

PVC low level flushing cistern 'white' with inlet, 10 litre capacity, float valve including bracket of 32mm dia, PVC pipe 600mm long, in repair, complete all as specified and directed.

Supply only PVC connections 15mm size with PTMT nuts of length 600 mm, brass fly nuts at both end, complete all as specified and directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580mm x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), including provision of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe, CI trap 100mm bore of pipe, in repair, complete all as specified and directed.

Vitreous China wash basin, white, flat back, size 550mm x 400mm fixed on cantilever MS brackets of 32mm dia, brass waste coupling, in repair, complete all as specified and directed.

Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc, 40mm dia bore, for WHB and sink, fixed in repair, complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5sq.m each with shutters (without taking off shutters from the frames), complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5sq.m but not exceeding 4.0 sq.m each with shutters (without taking off shutters from the frames), complete all as specified and directed.

PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in holdfast including necessary use and waste form work, complete all as fixed and directed.

MS work as in holdfast made out of flat iron including necessary welding or fixing nuts and bolts, complete all as specified and directed.

Rolled sections as in framing for cladding, glazing and fixed with angle cleats and connecting plates etc, conforming to Fe 410-W (Gde-E- 250) quality A, in repair, complete all as specified and directed.

MS work as in door or gate etc with angle or other section drilled or welded including all fixing and locking arrangement and holdfast, conforming to Fe-290 (Gde E-165), complete all as specified and directed.

Mild steel, plain black sheet (1mm thick) in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc, complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and directed. Make: Syntex / Rajshree Plastic Wood Forex, Indore.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in SSR Part- II 2004 and as directed by GE/ Engineer-in-charge. Note: Hinges, Glass or wire cloth in panels shall be measured separately.

Glazed and skeleton shutters, 35mm thick, second class hardwood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), divided into squares with plain, chamfered or rounded mitered beads for securing glass/gauge complete all as specified in SSR Pt- I, section 8, clause 8.24(a) and as direcetd. Note: Glass or wire cloth, etc. in panels or sash squares shall be measured separately.

Flush shutters, 32mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specifed and directed.

Block boards, grade 2 quality, 18 to 19mm thick, commercial type in cup board shutter/ shelves and fixed with screws and teak wood beading all around/ exposed surfaces, fixed in repair, complete all as specified and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

Factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and direcetd.

Factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complet all as specified and direcetd.

Steel ventilator with top hung shutter including box type hinges, steel peg stay, complete all as specifed and direcetd.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specifed and direcetd.

Sheet glass, 3mm thick, ordinary quality and glazing with oil putty or wooden beads in square not exc 0.5 sq. m in each pane,. Complete all as specified and direcetd.

Sheet glass, 4mm thick, frosted on one side, ordinary quality and glazing with oil putty or wooden beads in square not exc 0.5 sq. m in each pane, complete all as specified and direcetd.

Second class hardwood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including butt hinge etc & all necessary labours; articles n exc 200 cu. cm each, complete all as specified and direcetd.

Ordinary rat tail rod, 300 mm long, pattern springs including roller and roller plate, fixed in repair, complete all as specified and direcetd.

Mild steel sliding door bolts, 250 mm, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

Aluminium anodised,150mm long, barrel tower bolts of extruded section and fixed, conplete all as specified and direcetd.

Aluminium handles, 150mm size, cast type, anodised, complete all as specifeid and direcetd.

Butt hinges, 100mm mild steel medium weight cold rolled complete all as specified and directed.

Aluminium anodised hasp and staple, 150 mm, fixed in repair, complete all as specified and direcetd.

MS tubing of 25mm dia with PVC coating for curtain rod fancy type including fancy type PVC brackets (wall to wall or flush to wall) for securing to curtain rod, fixed in repair, complete all as specified and directed.

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, 30mm width of flaps (when open), complete all as specified and direcetd.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets including AC ridges in roof coverings, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as specified and directed.

Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, conforming to Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 MPa as in roof covering / cladding to wall, projection of window/door opening fixed with self tapping screws as specified, fixed in repair, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating (AZ-150) GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering / cladding to wall, projection of window/door opening fixed with self tapping screws as specified, complete all as specified and directed.

E- board (design lake and hill) of size 605mm x 605mm x 4mm thick, white prelaminated set, embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section (white powder coated); the framework shall comprises of main runner made of 0.33mm thick GS sheet and of size 24mm x 32mm x 300mm and spaced at 1200mm (maximum) centre-to-centre, hangers of GI wire 2.00 mm dia wire to be fixed by approval rawl plug level and fastener and screws etc, flush fitting of 1200mm long cross tee (double stitching) to be interlocked between main runners at 600mm centre-to-centre to form 1200mm x 1600mm modules, cross tee longer than 600mm to be supported independently, 600 x 600mm doubles to be formed by fittings 600mm long cross tee centrally between the 1200mm cross tee, perimeter wall angle shall be made out of 0.45mm thick GS sheet of size 19mm x 19mm and 300mm long of white colour, all as per manufacturers specifications, complete all as specified and directed. Make: Rajshree/polytuff/ Armstrong/ Everest, or equivalent.

Preparation of new plastered surfaces and applying two coats of acrylic emulsion paint over a coat of primer over & including 1mm thick wall care putty on walls complete all as specified and directed.

Preparation of new surfaces and applying two coats of cement base paint over a coat of primer over & including 1mm thick wall care putty on walls complete all as specified and directed.

Preparation of new wooden surfaces & applying two coats of synthetic enamel paint over a coat of pink primer exc 10 cm width or girth, complete all as specified and directed.

Preparation of new steel surfaces & applying two coats of synthetic enamel paint over a coat of red oxide exc 10 cm width or girth, complete all as specified and directed.

Preparation of old surface of Ceiling including cornices, pilastered, etc, by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying One coat of white wash on ceiling, complete all as specified and directed.

Preparation of old surface of walls including cornices, pilastered, etc, by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots including filling depressions of scrapped surfaces and applying one coat of acrylic emulsion paint, over and including a coat of 1mm thick wall care putty with preparation of plastered surfaces, complete all as specified and directed.

Preparation of old surface of walls including cornices, pilastered, etc, by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of cement base paint on wall surface over and including a coat of 1mm thick wall care putty, complete all as specified and directed.

Preparation of old wooden surfaces & applying one coat of synthetic enamel paint over 10 cm width or girth, complete all as specified and directed.

Preparation of old steel surfaces & applying one coat of synthetic enamel paint over 10 cm width or girth, complete all as specified and directed.

UPVC(SWR) pipes, 110mm bore, single socket in any length, with rubber ring joints fixed on walls, complete all as specified and directed.

UPVC(SWR) pipes, 75mm bore, single socket in any length, with rubber ring joints fixed on walls, complete all as specified and directed.

UPVC(SWR) bends in any radius, 110mm bore, provided with access door, fixed in repair, complete all as specified and directed.

UPVC(SWR) bends in any radius, 75mm bore, fixed in repair, complete all as specified and directed.

Taking down point wiring of any type, size and description (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. to match with the existing, complete all as specified and directed. NOTE: Credit for this items shall be made as per conditions separately.

Taking down main switches, DBs, cut-outs of any type alongwith existing boards and removing the same from site and making good disturbed surfaces of walls to match with the existing, complete all as directed by Engr-in-Charge, complete all as specified and directed.

Taking down carefully submain wiring of any type and size including earth wire on wooden batten / surface conduits / casing and caping etc., and removing the same from site and making good disturbed surfaces of walls to match with the existing, complete all as specified and directed.

Point wiring complete with PVC insulated unsheatehd, 1100 volts grade cable 1.5 Sqmm (nominal area) FR type multi stranded copper conductor, single core drawn in and including not less than 20mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories controlled by one, one way switch, including concelad opressed steel terminal box of required size not less than 1.6mm thick factory made duly painted inside and outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 3.0 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc, including 1.5 Sqmm FR type PVC insulated unsheathed cable multi stranded copper conductor as continuous earth wire and connected to earth dolly as required at site and including chases cutting & making good the disturbed surface and applying finishes to match the existing surface complete all as specified and directed for following:

(a) One light / fan point controlled by one switch

(b) 5 pin, 5 Amp socket outlet point on an independent board.

(c) 5 pin, 5 Amp socket outlet on the same board with other switch

(d) One bell/ buzzer point controlled by one bell push single pole one way.

(e) One 6 pin, 15/16 Amps socket outlet point on an independent board with cables of size 2.5 sqmm.

Switch piano, flush type single pole, one way 5/6 Amp 230 volts all as specified and directed.

Socket outlet, 2 in 1, 5 pin 5/6 Amps 230 Volts, flush type, complete all as specified and directed.

Switch piano, flush type, single pole, one way 15/16 Amp 230 volts all as specified and directed.

Socket outlet, 2 in 1, 6 pin 15/16 Amps 230 Volts, flush type, complete all as specified and directed.

Lamp holder, PVC / polycarbonate body with back plate suitable for batten fittings, complete all as specified and directed.

Ceiling rose, 3 phase/PVC/ polycarbonate, insulated body, surface bakelite sheet 63.5mm dia, complete all as specified and directed.

Bell push piano, flush type, single pole, one way 5/6 Amp 230 volts all as specified and directed.

Electric bell ding dong type AC 230 Volt 50 hz single pole all as specified and directed.

Ceiling fan regulator, electronic, rotary step type suitable for 1200/1400 mm sweep ceiling fan, complete all as specified and directed.

Sheet metal enclosure for MCB DBs SPN, 8 way, double door, 240 V with 200 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way, fixed in repair, complete all as specified and directed.

MCB SPN, 6 to 32 Amp, 240 Volt, 'C' curve, 10KA breaking capacity, complete all as specified and directed.

MCB SP, 6 to 32 Amp, 240 Volt, 'C' curve, 10KA breaking capacity, complete all as specified and directed.

LED mirror light fitting, 1x9W, LED 6000K, decorative indirect up-down light for mirror and as wall light application with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. Make: Havells / Phillips/ Crompton/ Bajaj

LED bulk head light fitting, 1x10W, LED 600 lumen, enclosed in polycarbonate body, weather proof, LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. Make: Havells / Phillips/ Crompton/ Bajaj

LED wall mounted tube light fitting, 1x18W, LED 6000K, decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. Make: Havells / Phillips/ Crompton/ Bajaj

Decorative wall light fixture made up of Polycarbonate, suitable for 15W TU retrofit CFL (B-22 base) polycarbonate body, weather proof, LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. Make: Havells / Phillips/ Crompton/ Bajaj

Road lighting luminarie 36 Watt, with unique peanut optics to ensure uniform distribution, higher spacing between poles and maintenance free system for city roads and streets, 50% energy savings, IP66 Protection PC and FG cover, high impact resistance complete including LED lamps and all accessories including bracket made out of 25mm bore GI pipe (light grade), 1.20m long made to shape and fixed to existing pole or building by means of 2 Nos MS flat iron 40x6 mm clamps with suitable size bolt, nuts & washers and connecting with 3 core flexible copper wire of size 23/0.0076 from ceiling rose to existing junction box, complete all as specified and directed. Make: Havells / Phillips/ Crompton/ Bajaj

Sub main wiring with two single core PVC insulated unsheathed, grade cable 4sqmm (nominal area) FR type multi stranded copper conductor and one run of 4 sqmm nominal cross sectional area FRLS PVC insulated unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 20mm dia rigid PVC conduit and fittings, including taking down existing sub main wiring, complete all as specified and directed. Note: One unit length shall be measured as two run of main wire and one run of conduit & earth wire.

Taking down carefully ceiling fan/exhaust fan keeping in safe custody cleaning & servicing the fan including painting with one coat of synthetic enamel paint & marking MES No. refixing in position including replacement of three core 23/0.0076 copper conductor, complete all as specified and directed.

Taking down carefully existing geyser keeping in safe custody cleaning & servicing the fan including painting with one coat of synthetic enamel paint & marking MES No. refixing in position including replacement of three core 23/0.0076 copper conductor, complete all as specified and direcetd.

Two pin, earth plug and socket with 1 MCB single pole 20 to 32 Amps C series 10 KA in sheet metal enclosure and connecting, fixed in repair, complete all as specified and directed.

Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6, complete all as specifieid and directed.

Brickwork with subclass ‘B’ bricks (except bricks), straight or curved on plan exc 6m mean radius built in CM 1:6, complete all as specifieid and directed.

Vitrified Ceramic tiles, dark shade, 8-9 mm thick (square) polished, 600mm x 600mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile, including provision of 10mm thick rendering in CM 1:4, complete all as specified and direcetd.

Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including cutting, polishing and moulding edges including 20mm thick screed bed or bedding layer in CM (1:3), complete all as specified and directed.

Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces of walls, finishing the surface even and smooth with out using exta cement, complete all as specified and directed.

RCC 1:2:4 type B-1, using 20mm graded stone aggregate, in shelves/Chajjas, complete all as specified and directed. Note: Reinforcement to be measured separately.

Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed. Note: The girth of the chase shall be reckoned as that actually required for the work, that is, maximum height of the article or portion thereof inserted in the chase plus twice the depth of insertion.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough flat surfaces of concrete, complete all as specified and directed.

Form work to edge of concrete exc 5 cm but not exc 10 cm wide for rough finished flat surfaces of concrete, complete all as specified and directed.

Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Taking down existing wall finishes any type by vigorously wire brushing brooming, dusting and finally washing with water to clear the surface absolutely free from any kind of existing finishes & foreign and making good minor cracks etc in cement mortar 1:3 and applying birla putty 2 kg per sqm on the surface with uniform thickness and making surface absolutely smooth & applying two coats of acrylic emulsion paint, white or tinted over priming the surface with alkali resistant priming paint complete, complete all as specified and directed.

Cement concrete type B-1, 1:2:4 (20mm graded aggregate), 25mm thick as in levelling course of floor etc, complete all as specified and directed.

Taking down shutter of any description not exceeding 2 Sqm each, complete all as specified and directed.

Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh on metal frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

Preparation of newly decorated surfaces of ceiling and applying 2 coats of plastic emulsion paint coloured or white or tinted with one coat of internal base primer, complete all as specified and directed.

Preparation of old surface of walls including cornices, pilastered, etc, by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots including filling depressions of scrapped surfaces and applying two coats of acrylic emulsion paint, over and including a coat of 1mm thick wall care putty with preparation of plastered surfaces, complete all as specified and directed.

Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame, fixed in repair, complete all as specified and directed.

PVC sheet (5mm thick) fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame, complete all as specified and directed.

Preparation of new wood or wooden based surface with sand or emery paper of any description over 10 CM width or girth treated with creosite oil complete all as specified & directed.

Asbestos cement 6 mm thick corrugated or semi corrugated sheet as in roof covering, walls etc fixed with L or J type hooks or cranked bolts complete all as specified & directed.

Asbestos cement 6 mm thick two piece adjustable Serrated ridge for corrugated sheets fixed with L type or J type bolts, complete all as specified and directed.

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings in cement mortar, complete all as specified and directed.

Rolled MS sections as in main and cross beams and purlins of Fe 410-W (Gde-E- 250) quality-A, complete all as specified and directed.

Sub main wiring with two single core PVC insulated unsheathed, grade cable 6sqmm (nominal area) FR type multi stranded copper conductor and one run of 6 sqmm nominal cross sectional area FRLS PVC insulated unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 20mm dia rigid PVC conduit and fittings, including taking down existing sub main wiring, complete all as specified and directed. Note: One unit length shall be measured as two run of main wire and one run of conduit & earth wire.

Sheet metal enclosure for MCCB DBs TPN, 4 way, double door (acrylic), 415 V with 200 Amps rated bus bars, including MCCB of 160 Amp TPN breaking capacity 25KA with thermal magnetic release as incommer and 6 Nos MCB SP 6-32 Amp 'B' series breaking capacity 10KA as outgoing & blaking plate wherever required and IP-43 degree protection making necessary electric connections with lugs, complete all as specified and directed.

Recess mounting decorative LED fitting size 600 x 600 LED 34W high brightness SMD LED including suitable driver connection and testing complete all as specified and directed. Make: Philips Cat Part No. RC383B LED 28S- 4000 PSU OD WH PIR or any techno-commercially equivalent model in Crompton/ Bajaj/Havells

LED tube light fitting, 1x20W, LED 6000K, decorative ultra slim linear LED lighting fixture with extruded aluminium body/heat sink, environmental friendly, energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of length not more than 1.2 mtr, complete all as specified and directed. Make: Endura Linear Neo 20W of Havells (Cat No LHEXBLP7PN1W020) or any techno-commercially equivalent model in Philips/ Crompton/ Bajaj

XLPE cable insulated screened metet PVC beded galvanised steel strip or wire armoured, elect power cable (Heavy Duty) 1100 Volts grade with stranded aluminium conductor of 3.5 core 150 Sqmm complete all as specified and directed.

MCCB 4 pole, 160 Amps, 36 KA, 415 Volts, Adjustable type, in existing Feeder pillar, complete all as specified and directed.

PERFECT ENTERPRIOSES

SHIVAM TRADERS

Shivagya Engineering

JAI MAA VINHYAVASANI CONSTRACTION CO

sethi tradres

Ram Babu Bros

M/S SS Tarders

M S Enterprises