SPECIAL REPAIR TO BLDG NO NP 03 SINGLE OFFRS ACCN AT TAWI VIHAR UNDER GE (ARMY) DHAR ROAD UDHAMPUR

Amount

Demolition of Brickwork or stone/ boulder masonry, built in Cement mortar including all quoins, arches, pillars, etc, but including ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed .

M&L for Brickwork with subclass 'B' bricks (old size bricks), straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as directed.

All as per Srl item Srl No 2 above here in but except bricks.

M&L for brick work with sub class ‘B’ bricks (old size brick) straight or curved on plan to any radius in half bricks thick walls, built in CM 1:4 complete all as directed.

Taking down cement plaster of any description on concrete surfaces such as soffit of RCC slab, chajjas and brick walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

M&L for rendering 15 mm thick cement plaster in CM 1:6 on brick Work or concrete surfaces including finished even and smooth without using extra cement all as specified and directed.

M&L, Rendering 15mm thick in CM 1:4 on of brick work or concrete surface finish ever and smooth (w/o using extra cement) incl WPC as per user manual at any height etc complete all as specified and directed. (WPC will be measured and paid separately).

Supply only liquid WPC

M&L for rendering 10 mm thick in CM 1:3 over concrete surface as on ceiling, chhajja, shelves etc to match with existing surfaces finish even and smooth w/o using extra cement complete all as specified and directed. .

M&L for applying two coats of oil emulsion distemper on wall over one coat of primer over new plastered surface and obtain smooth finish using sand paper etc complete all as directed.

M&L for preparation of new plaster or unplastered surface of wall /roof boarder, chajja/roof facia column etc and applying two coats of exterior emulsion paint over a coat of acrylic primer completed all as directed.

M&L for preparation of new plastered surface and applying two coats of oil emulsion distemper on ceilling over one coat of primer etc complete all as directed.

M&L for preparation of old surfaces by removal of existing treatment and applying two coats of oil bound distemper on ceiling over one coat of primer etc complete all as directed.

M&L for preparation of plastered surfaces of wall by applying 2mm thick wall care putty in two coats and smoothening the surface with sand paper/mechanised sanding etc preparatory to paint complete all as spcified and directed.

M&L for preparation of old surfaces by removal of existing treatment on wall, roof boarder, chajja/roof facia, column etc and apply two coats of exterior emulsion paint over a coat of acrylic primer complete all as specified and directed .

Demolition of cement concrete unreinforced in ground floors and paving n. exc 15 cm thickness below or above gound level , concrete debris and rubbish to a distance n exc 100m as directed by the EIC.

M&L 75mm thick PCC type D-2, 1:4:8 (using 40mm graded aggregate) as in sub base all as specified and directed.

M&L for 50mm thick PCC 1:3:6, nominal mix, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in alternate bays (not exceeding 2 Sqm each) surface finished even and fair without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising of one part of bitumen 85/25 grade and three parts of sand by weight, complete all as specified

M&L for 25 mm thick plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in floors finished smooth and even without using extra cement all as specified.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular ) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in floor of shade & designed as approved by GE,set and jointed in neat cement slurry and pointed with white cement with colour pigment to match the colour of tiles over,15 mm thick rendering in bedding layer or screed bed in cement mortar (1:4) in floors etc including dismantling of tiles complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surface 450x350x 7 mm thick set andjointed in neat cement slurry and pointed in white or colour cement to match with tiles including 10mm thick rendering in CM (1:4) backing of wall tiles such as dado/skirting in vertical surface etc including dismantling of tiles complete all as specified and directted. Note : shade & design as approved by EIC/GE.

M&L for virified tiles light shade 10mm thick (square/rectangular) polished , area of each tile not exc 0.36sqm in floors dado, skirting etc set and jointed in neat cement slurry over 15mm thick screed bed of bedding layer in CM 1:4 for laying floor finish and pointed in white or coloured cement to match and incl dismantling /demolition and rubbish off the primises etc complete all as specified and directed

M&L for green marble 15-17 mm thick over cement screed bed laid on 15 mm thick CM 1:6 and jointed with grey cement slurry mixed with pigment ot match the shade of the slab / staircase / steps,riser incl rubbing and polishing incl moulding rounding to edge of marble & dismantling complete all as specified and directed.

M&L for Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding ,rounding of edgeing and dismantling complete all as spd and directed.

Taking down chowkahts or frames with shutters (without taking off shutters from the frame) not exceeding 1.5 Sqm each and all as specified and directed.

Taking down chowkahts or frames with shutters (without taking off shutters from the frame) exceeding 1.5 Sqm but not exceeding 4 sqm each and all as specified and directed.

M&L for factory made, 2nd class hard wood, 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass / gauge etc. (without sash bars) edges or framing plain, chamfered or rounded fitted with cut or mitered beads for securing glass etc. size of members of shutters as specified in SSR Part - I section 8.24 (a), all as specified and directed by Engr-in-Charge

S&F 35 mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

M&L for factory made solid PVC moduled door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification & drawing and all as directed by the Engr- in-Charge.

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specified

M & L for Pressed steel frames of size 125x60mm, for doors with one or more rebates febricated out of 1.25mm thick mild steel sheets with and including necessary fixing lugs, hinges, (100mm) medium weight -03 Nos on each rebate) lock strike plate incl filling hollow portion in PCC 1:3:6 type C1 using 20mm crushed stone and making good the existing surface in cement mortar 1:6 complete all as specified as directed.

M&L for pressed steel frames of size 75mmx60mm for cupboard frames with one or more rebates fabricated out of 1.25mm thick mild steel sheets with and including necessary fixing lugs, continuous (Piano) hinges mild steel bright finished or electrogalvanised width of flaps (when open) 30mm and fixed with chowkhat by rebated and welded, lock strike plate with and including filling of hollow portion in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and making good the existing surface in cement mortar 1:6, complete all as specified.

S&F for aluminum anodized barrel tower bolts of extruded section 150mm long (ISI Marked) complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, 300 mm long.

S&F for aluminum handles cast type anodized 150mm long (ISI Marked) complete all as specified and directed.

Preparation of new wooden or wood based surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, all as specified.

Preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, all as specified.

M&L for one coat of synthetic enamel paint on steel surface including preparation of old steel surface width or girth exc 10cm all as specified and directed.

Powder coated Aluminium window/vents complete all as specified in specification and as shown on drawings for various size and pattern with following powder coated aluminium sections. Notes:- A. The rates quoted for powder coated aluminium section shall be deemed to incl the fwg: :- (i) Rubber gasket for fixing glass to window /vent shutters. (ii) Fixing of window with and incl min 75X10 GI screws all around @ 300 c/c (Min 2 Nos on one side) with PVC RAWL PLUGS/Sleeeves. (iii) Rollers, concealed lock cum handles & other fittings for sliding shutters shall be provided as per manufactures instructions and approved by GE. (iv) Silicon sealant shall be applied on internal as well as external peripheri of window and masonry joint to avoid water seepage. (v) All other sundries all as per manufacturer instructions and as directed. (B). The rates coated for powder coated sections shall exclude the cost following and shall be paid seerately under respective time of Sch 'A"/BOQ:- (i) Glass and wire mesh (ii) 40x40x3 aluminium angle provided on all corners of the window. (C) Aluminium U-Channel shall be provided for fixing of wire mesh. (D) Powder coated aluminium handles and hinges for fixing of openable shutters C. Others (i) No allowances for wastage/overlaps shall be considered for payment. (ii) Range of dimension of opening size has been mentioned, the same shall be fixed as per measurement of opening of windows as per site requirement by the GE/EIC during execution of works. (iii) Powder coated aluminium section shall be provided all as shown on drawings and as directed.

(a) Powder coated aluminium section as in frame of window/vents and track for sliding shutters and any frame work.

(b) Powder coated aluminium section as in sliding window/Openable shutters

(c) Powder coated aluminium tower bolts 75mm long and fixed

(d) Powder coated aluminium but higes 75mm and fixed

(e) Powder coated aluminium handle 75mm and fixed

M&L for 4.80mm Thick Glass ordinary quality glazing or black with aluminum beeding and gasket to aluminium framewoork in square exec 0.50 Sqm in each pane all as specified

5.0mm Thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane in repair complete all as specified

Galvanised mild steel wire cloth 0..36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

100mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws conpleted all as specified

Miror Cabinet PTMT of 400mm x 500mm with megnetic looking arrangements fixed with and including wooden plugs with chromium plated brass screws complete all as specified and directed. Make Prayag Cat Part No 554 or equivalent in Make as per Appx 'E' to particular specification

Wall mixer with provision for overhead shower with 115 mm long bend pipe on upper side, connecting legs and wall flanges, complete all as specified and directed. Make: Jaguar Cat Part No CON 273KNUPR or equivalent in Make as per Appx 'E' to particular specification

Tubular towel rail, 20mm dia, D type, 60cm long between flanges of brass chromium plated with and incl chromium plated brass screws and wooden/plastic cleats complete all as spd and directed

S &F in repair for Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as spd and directed

S &F for Glass shelf assembly 200mm fixed with brass screws and plugs complete all as spd and directed

S & F in repair Bib taps CP Fency type long body 15mm bore with will crutch or , buttewrfly handle, screwed down, screwed for iron pipe completed with all fittings complete all as spd and directed

S&F in repair Stop Cock/angle CP Fency type 15mm bore screwed down high pressure with crutch of buttewrfly handle & screw both end for iron pipe or for Unions complete all as per specified and directed

S&F Vitreous China, wash hand basin, counter top, white, of size 530mmx445mmx195mm including brass CP waste coupling 32mm dia with long screwed shank and fly nuts,32mm dia, chain and plug, porcelain stopper with and including PVC collapsible waste pipe of suitable length, fixed in repairs, complete all as specified. Make: Jaquar Cat Part No. ECS-WHT-601 or equivalent in Make as per Appx 'E' to particular specification

S&F in repair Chromium plated brass Centre hole mixer without pop up waste system 15mm bore for mixing hot and cold water screwed down for iron pipe for WHB, complete all as specified. Make: Jaquar Cat Part No. CON-167KNV or equivalent in Make as per Appx `E' to Particular specification.

S & F for one piece closet with bowl for cupled WC with PP soft seat cover, hinges fixing accessories and accessories set of size 360mmX680mmX765mm, strap 220mm cistern with cistern fitings and necessory fitings complete fixed in repairs, complete all as specified Make: Jaguar Cat Part No CNS-WHT-755SS or equivalent in Make as per Appx 'E' to particular specification

S & F for Peg Set of Six Stainless steel of suitable length, completed all as specified. Make: Prayag Cat Part No BEA 30 or equivalent in Make as per Appx 'E' to particular specification

S & F for Toilet paper holder, stainless steel fixed with and including chromium plated brass screws and wooden /plastic cleats on walls completed all as specified Make :- Jaguar Cat Part No AKP 35753PS orequivalent in Make as per Appx 'E' to particular specification

S&F for health faucet brass chromium platged with 8mm dia 1.2mtr long flexible pipe and wall hook fixed with brass chromium plated screws completed all as specified Make :- Jaguar Cat Part No ALD CHR-573 or equivalent in Make as per Appx 'E' to particular specification.

S&F for corner glass shelf 200mm (brass brackets) fixed with brass screws and plugs completed all as specified Make :- Jaguar Cat Part No ACN -1173 or equivalent in Make as per Appx 'E' to particular specification

S&F for PVC connections 60cm long 15mm superior quality with PTMT nuts on both side completed all as specified and directed

S&F for 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed completed all as specified and directed

S&F in repair for 25 mm dia Decorative/fancy type stainless steel curtain rod with brackets and knobs at both ends as per site requirement incl taking down old existing pipes with accessories complete all as specified and directed. Note: the cost of brackets and knobs is deemed to be incl in the quoted rate.

Taking up or down 15 mm dia bore steel tubing and connection completed all as specified and directed.

S&F for GI tubing 15mm bore medium grde with all fittings and fixed complete to wall and ceiling or laid in floors etc incl cutting chases in brick wall pinning in making good in CM 1:3 to facings where required incl 10cm exe but not exc 20cm in girth all as directed and specified.

Taking up or down 20 mm dia bore steel tubing and connection complete all as specified and directed..

S&F GI tubing 20 mm bore medium grade medium grde with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

S&F for 110mm bore PVC pipes single socketed Pressure rating @4Kg/Sq cm length "medium grade " with rubber ring joint, fixed to walls with dash ture nut and bolt at every 2 mtrs length complete , incl taking up/down old pipe with all fittings all as specified and directed by Engineer-in-charge.

All as per Ser No71 Above but laid in trench or in floor

S&F in for 110 mm bore PVC bends/junction any radiuos complete all as specified.

S&F in for 110 mm bore PVC bends/junction with access door any radiuos complete all as specified.

S&F for 110 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified.

S&F for 110 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified & directed .

S&F for 75mm bore PVC pipes single socketed Pressure rating @4Kg/Sq cm length "medium grade " with rubber ring joint, fixed to walls with dash ture nut and bolt at every 2 mtrs length complete , incl taking up/down old pipe with all fittings all as specified and directed by Engineer-in-charge.

All as per Ser No 77 Above but laid in trench or in floor

S&F in for 75mm bore PVC bends/junction any radiuos complete all as specified.

S&F in repair grating round 125mm size of CP complete all as specified and directed.

S&F for plain Gypsum Board panel 12.5 mm thick in ceiling fixed with and incl necessary GI frame used with 'T' or any section accessories etc of galvanbized steel all as per manufacturers designs confirming to IS-2095 and 2542 (1981) the weight of the board shall be not less than 7 kg per sqm incl dismantling of walls and ceiling board any type and two coat of OBD over a coat of putty complete all as specified and directed

S&F for Plain, Aluminium sheeting,0.56mm thick Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing fixed to walls and fixerd with screws complete all as specified and directed.

Water proofing treatment to floor & vertical surfaces of sunken portion complete comprising the following: - (a) After demolition of floor & lime concrete etc. remove all loose particles along with existing water proofing treatment (any no. of layers) with wire brushes and cleaning the surfaces with water. (b) Brushing cement slurry with 1.2 kg of cement per square metre duly blended with & including water proofing compound. (c) 15 mm thick (Average thickness) plaster in cement mortar (1:3) mixed with WP compound on sunken surface including walls. The corner of sunken portion shall be rounded in concave shape and adequate slope shall be made during plastering to accommodate sump pipe and curing the sunken portion with water minimum for 48 Hrs by ponding. (d) Applying self adhesive type APP based polymeric membrane minimum weighing not less than 3.6 kg/ Sq. m and minimum 3 mm thick reinforced with polyester non-woven fabric (weight not less than 150 gm/Sq. m),(e) M&L for PCC 1:7 :12 for fillin of sunken portion after conceling all menbrane and sealing all joints to the entire with broken bats and light weight all as satisfaction of Engineer-in-Charge. MAKE: LAFARGE, TEXA, STP, BENGAL AQUAFLUX. lAFARGE, TEXA, STP, BENGAL AQUAFLUX.

M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-16, complete all as specified and directed.

Expanded metal, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanized steel staples supplied and fixed complete to wood or steel members, weight exc 4 Kg per Sqm, complete all as specifed & directed.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in coping/benching and all other similar works including necessary formwork complete all as directed.

M&L for PCC 1:2:4 type B0 (using 12.5mm graded stone aggrgatte) as in copping /benching and all other similar works including necessary framework complete all as specified and directed.

Machine pressed precast concrete interlocking paver block, shape and size as approved by the GE, confirming to IS 15658-2006 of 60 mm thickness, with grey cement and pigment complete all as specified and as directed

Sand filling under floors or in foundations including watering and consolidation complete all as specified

Earth work in excavation by mechanical means (Hydraulic excavator)/ infoundation trenches ordrains (not exceeding 1.5 min width or 10 sqm onplan), including dreessingof sides and ramming ofbottoms, lift upto 1.5 m,including getting out the excavated soil and disposal of surplus excavated soil asdirected, within a lead of 50 m. in any type of soil all as specified & as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified & as directed.

Supply and laying in trenches jointing and testing salt glazed stoneware pipe grade 'A' drainpipe 150mm bore sonfirming to IS at any depth after they are laid and tested complete all as specified & as directed.

M&L PCC 1:3:6 type C2 as in concrete bed to 150 mm bore drain pipe and over incl packing under haunching against the sides of pipes after pipe laid and tested complete all as specified & as directed.

GI tubing 50mm bore medium grde with all fittings laid in trenches including testing including taking down old unserviceable GI Pipe complete all as directed and specified.

GI tubing 20mm bore medium grde with all fittings laid in trenches including testing including taking down old unserviceable GI Pipe complete all as directed and specified.

S&F in replacement Gun-metal, globeGun-metal, globe or gate valves, 50 mm bore with iron wheel head, screwed both ends for iron pipe and fixed all as directed and specified.

S & F in replacement Gun-metal, globeGun-metal, globe or gate valves, 20 mm bore with iron wheel head, screwed both ends for iron pipe and fixed all as directed and specified.

Cutting/making hole into CI/DI/MS pipes of 150 mm carefully and insertion of new tee incl clamping with suitable size clamp for taking small branch connection upto 50 mm bore complete all as directed by EIC.

M&L for dismentling the U/S valve chamber including rusted MS cover complete with out disturbing the existing pipe line and Costruction of new valve chamber incl necessary earth work in any type of soil, PCC foundation C-2 (1:3:6) type C2 40mm graded stone aggregate as in base concrete ,brick work in CM 1:6 with 10 mm thick plaster internally and 15 mm thick externally in CM 1:4 , 6 mm thick MS cover plate of suitable size with hinges and locking arregement fixed to angle iron frame made out of 40x40x6 mm MS angles complete with 2 coats of synthetic enemal paint over one coat of red oxide primer on all metal works & three coats of white wash on all plastered surfaces of valve chambers size 900mm x 900mm x 900mm complete all as specified & directed by Engr -in- charge.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.and making good disturbed surfaces of walls, floors, etc.

Material and labour for conceled type Point wiring complete ( modular type ) with 1.5 sqmm single core PVC insulated medium grade ISI Marked,FRLS unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC non metalic PVC conduit medium grade not less than 20mm dia with all accessories like tee, straight joint, L Bend etc.,concealed on walls, sufrace on ceiling/ floors etc., and including provision of PVC heavy duty Insulated FRLS copper conductor, 1.5 sqmm for earth continuity conductor and connected to common earth dolly and making good the disturbe surface complete all as specified and directed. Note :- cover plate with frame and metal box will will measured and paid separately.

One light / Exhaust Fan/Ceiling fan & One Bell/buzzer point controlled by one switch.

One switch socket outlet point 3 pin 5 Amps on Independent board.

One light point controlled by two 2-way switches, with cables 1.5 sq. mm size

Material and labour for Point wiring conseled type complete (for modular type ) with 2.5 sqmm single core PVC insulated heavy duty ISI Marked,FRLS unsheathed cable 1100 volts grade with multistranded copper conductor in and including PVC white non metalic PVC conduit Medium grade not less than 20mm dia with all accessories like tee, straight joint, L Bend etc.,concealed on walls, sufrace on ceiling/ floors etc., and including provision of PVC heavy duty Insulated FRLS copper conductor, 1.5 sqmm for earth continuity conductor and connected to common earth dolly making good the disturbe surface complete all as spd and directed. Note :- cover plate with frame and metal box will will measured and paid separately.

Material and labour as in repair for sub main wiring with two single core PVC insulated unsheathed copper conductor cable 6 sqmm drawing in and including rigid non metalic PVC heavy duty 25 mm dia conduit concealed on wall/surface on ceiling with one additional PVC insulated FRLS unseathed wire of copper conductor of 6 sqmm for earth continuity conductor incl taking down old Unsv submain any type and size and making good the disturbed surface complete all as specified and directed by EIC.

Material and labour for sub main wiring with two single core PVC insulated unsheathed copper conductor cable 4 sqmm drawing in and including rigid non metalic PVC heavy duty 25 mm dia conduit concealed on wall/surface on ceiling with one additional PVC insulated FRLS unseathed wire of copper conductor of 4 sqmm for earth continuity conductorand making good the disturbed surface complete all as specified and directed by EIC.

S&F in repair batten Lamp holder, PVC/Polycarbonate type all as specified and directed.

S&F as in repair Bulk Head fittings with 10 watt LED lamp on wall all as specified and directed by Engineer-in-charge.

Supply and fixing LED 9 Watt lamp , 240 Volt, 50 Hz lamp

Supply and Fixing LED 20 Watt light fitting Batton type integrated LED channel, integral sleek extruded polycarbonate LED Channel with white acrylic cover and including connecting up with twin core flexible copper conductor cable with suitable size complete with all accessories incl taking down complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED street light fitting 40 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver,LED panel with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection incl taking down complete as directed by EIC

S&F 1.5m long 40mm bore light grade GI pipe bracket duly cut to size and bent to shape required duly painted with 2 coats of aluminium paint (of approved tint) over a coat of red oxide primer, including suitable 2 Nos. Clamps as required to fix on concrete / steel poles incl taking old unsve GI bracket any type and size complete all as specified and as directed

Taking down carefully existing ceiling fan any type and size , removing its fan blade and deposited in MES store for safe custody all as directed by Engr-in-Charge

Taking down carefully existing Exhaust fan any type and size and deposited in MES store for safe custody all as directed by Engr-in-Charge

Taking down carefully existing Electric Water Heater (Geyser) any type and size and deposited in MES store for safe custody all as directed by Engr-in-Charge

Refixing of existing serviceable ceiling fan any size from MES Store Yard along with new connection wire 3 core duly refixing the blade along with new MS clamp properly all as directed

Refixing of existing serviceable Exhaust fan any size from MES store yard including fixing with fastnuts and provisioning of three core flexible copper cord of required length from ceiling rose or connectror to Exhaust fan for connection, complete all as directed by Engr-in-charge.

Refixing of existing serviceable electric Water Heater (Geyser) any size (Geyser to be collected from MES Store yard) including fixing with fastnuts complete all as directed by Engr-in-charge.

Supply and fixing Ceiling fan AC single phase 230 volts for size 1200 mm sweep, including fixing arrangement such as nut, bolts, washer etc, making good the disturbed surfaces matched with existing finishes comprising with necessary eletric connection with suitable copper wire from ceiling rose complete all as specified and directed.

S/F Call Bell AC 230 V Single Pole along with necessary electric connection all as spd and directed.

S & F ceiling rose Ceiling rose, PVC/polycarbonate, isolated body all as specified and directed.

Supply and fix Modular switch 1 way 6A,1 module

Supply and fix Modular switch 1 way 16A,1 module

Supply and fix Modular switch 2 way 6A, 1 module

Supply and fix Modular Bell push 6A 1 module

Supply and fix Modular Socket, 6A - 2/3 pin combined 2 module

Supply and fix Modular Socket 6A/16A - 2/3 pin combined 2 module,

Supply and fix Modular Fan step regulator, 120W - 2 module

supply and fix white cover plate with frame, 1 module

supply and fix white cover plate with frame, 2 module

supply and fix white cover plate with frame, 3 module

supply and fix white cover plate with frame, 4 module

supply and fix white cover plate with frame, 6 module

Supply and fix modular Metal flush box 1/2 module

Supply and fix modular Metal flush box 3 module

Supply and fix modular Metal flush box 4 module

Supply and fix modular Metal flush box 6 module

Supply and fixing as in repair Metal clad socket outlet with single pole and nuetral enclosure with two pin and earth plug socket complete with one single pole MCB 20 Amps complete all as specified and directed by EIC.

Supply & Fixing TPN DB 4 Way distribution Box, double door of protection grade IP 42 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar complete confirming to IS 13032 & 8623 incl taking down old UNSV TPN DB any type and size complete all as specified and directed.

Supply & Fixing SPN Distribution Box, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar of 8 way, confirming to IS 13032 & 8623 including taking down old unsv DB complete all as specified and directed.

Supply & Fixing TPN Distribution Box, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar of 4 way including 100 Amp MCCB ,4 pole 415 Volt 25 KA breaking capacity as incomer , confirming to IS 13032 & 8623 complete all as specified and directed.

Supply & Fixing MCB SP, 06 to 32 Amps 240 volts, AC , 10 KA breaking capacity 'B' Series,"ISI marked complete all as specified and directed.

Supply & Fixing MCB SPN, 40 to 63 Amps 240 volts, AC , 10 KA breaking capacity 'C' Series,"ISI marked and conforming to IS 8828/IEC 60898-1 complete all as specified and directed.

Supply & Fixing MCB TPN 63 Amps 440 volts, AC , 10 KA breaking capacity 'B' Series,"ISI marked complete all as specified and directed.

M&L as in repair for earthing as per IS:3043 with galvanized steel earth plate electrode 600 x 600 x 6.0 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanized iron wire 4 mm dia (8 SWG) as earthing lead protected by GI pipe light grade 15 mm bore for protection of GI earth wire and 20 mm dia GI pipe medium grade for watering with alternate layers of charcoal /coke and salt including all accessories like nut, bolts, reducer, nipple, wire meshed/screened funnel and making brick masonry finished chamber of internal size 300 mm x 300 mm x 300 mm with concrete base, covered with PCC cover which shall be embedded in the block masonry including excavation works, refilling, connected to main switch/MCB DB for feeding the electric supply to domestic quarters compete all as specified as shown in electricall plateNo. 3 of SSR Part-I and testing of earth resistance as required. Note : Earthing lead/G.I.Earth wire upto 7.5 metre length shall be deemed to be included in quoted unit rate beyond 7.5 metre, the same shall be measured and paid separately).

Material and labour for earth Test point terminal block , drilled and screwed including all as directed.

Supply and fix LED Mirror wall light fittings 10/9 Watt, 240 Volt, 50 Hz complete all as specified and directed.

Material and labour as in repair for sub main wiring with four single core PVC insulated unsheathed copper conductor cable 10 sqmm drawing in and including rigid non metalic PVC heavy duty 32 mm dia conduit concealed on wall/surface on ceiling with one additional PVC insulated FRLS unseathed wire of copper conductor of 6 sqmm for earth continuity conductor incl taking down old Unsv submain any type and size and making good the disturbed surface complete all as specified and directed by EIC.

Material and labour for 18mm thick MDF board one side decorative laminated PVC sheet complete all required for cabinate/ cupboard shutter/ partition / shelves etc. in required size at site. The panel shall be fabricated using adhesive and secured as required As edges shall be cobered with 2mm thick edge bounding tapes or 90 degree edge bent finished as per manufecturer instruction.

Mild Steel for framed work as in safty door fabricated out of mild steel hollow sections of sheet thickness not less than 1.6mm thick, MS square bar or other section with rails, braces, sliding door bolt fabricated out of 16mm MS round bar staple etc with the provision for fixing of wire mesh complete and fixed to mild steel pressed chowktas complete all as specifeid and directed.

MAHADEV ENTERPRISES

VISHWA MITTAR PACHYALA

NARESH KUMAR KHAJURIA