PROVN OF 03X BATH ROOM WITH WATER TANK STAGING NEAR BLDG NO T-228 AND SPL REPAIRS TO 01XPS TANK OF CAPACITY 10,000 GLN INCLUDING ITS ALLIED WORKS PUMP HOUSE NO-01 AT ZAKHAMA MILITARY STATION UNDER AGE(I) ZAKHAMA.

Amount

Surface dressing n exc 15 cm deep in soft/loose soil complete all as specified and directed.

Excavation over area, n. exc 1.5m in depth and getting out in hard/dense soil complete all as specified and as directed.

All as per item serial No 02 here-in-before but depth exceeding 1.5 m and not exceeding 3.0m complete all as specified and as directed.

Excavation in trenches not exc 1.50 m wide and not exc 1.50 m deep for foundation or for shafts, wells cesspits,man holes, laying of cable etc not exc 10 Sqm on plan and n exc 1.5m in depth and getting out in hard/dense soil complete all as specified and as directed. hard/dense soil

Returning, filling, in soil including spreading, levelling, watering and well ramming in layers n.exc. 25cm thick complete all as specified and as directed.

Removing excavated soil to distance not exc. 50 m and depositing where directed at a level not exc. 1.5 m above the starting point etc complete all as specified and as directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for hardcore with broken stone or boulder of gauge not exc 63 mm, deposited , spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surfaces complete all as specified and as directed.

M&L for PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete etc. complete all as specified and as directed.

M&L for 100 mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M & L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A' complete all as specified and as directed.

M&L for 40mm thick damp proof course 1:2:4 type B0(using12.50mm graded stone aggregate) and applying evenly a tack coat of blown bitumen 85/25 @ 1.5kg per sqm. and blinding with clean dry sand @ 0.05 cu. m. per sq. m complete all as specified and as directed.

M & L for PCC 1:3:6, type C1 (using 20 mm graded stone aggregate) as in coping, cills, hold fasts, fixing of post, water trough, lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, etc. including necessary formwork (straight or curved) complete all as specified and as directed.

M&L for RCC type 1:2:4, type B-1 (using 20mm graded stone aggregate) as in slabs supported on walls,beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc. complete all as specified and as directed.

Use and waste formwork to sides and soffits of floor or roof beams, beams haunchings, girders, bressumers, lintels, cantilevers, shelves including supports overhangs etc also splays between floors and beams etc. in rough finished flat surfaces of concrete complete all as specified and as directed.

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape as required including cutting, bending cranking, hooking end and binding with mild steel wire(annealed) not less than 0.9mm dia as in reinforcement bar complete all as specified and as directed

M&L for mild steel TMT bars 8 mm dia and over upto and including 10mm dia cut to length, bent to shape required including cutting, cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan any radius, built in cement mortar 1:4 as in half brick thick works complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks, straight or curved in one brick thick honey comb built in cement mortar 1:3 complete all as specified and as directed.

M&L for Loose filling with Broken stone or boulders, aggregates of gaugae 80 t0 150mm in soakge pits, soakage wells complete all as specified and as directed.

M & L for rendering 10 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:4), in two layers, under coat of 10 mm thick & top of 5 mm thick, to other than fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound (@ 3% by weight of cement or as per manufacture's instructions), finished even and smooth without using extra cement complete all as specified and as directed. Note : Water proofing compound will be measured and paid separately as "Supply only".

Supply only integral water proofing compound complete all as specified and as directed.

M&L for preparation of newly plastered surface of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

M&L for preparation of newly plastered surface of walls and applying two coat of cement base paint over a coat of primer complete all as specified and as directed.

M & L for rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St.-240 complete all as specified and as directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and as directed.

M & L for preparation of new steel surface over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws complete all as specified and directed.

S&F factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails, MS frames shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stills and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ scaled to the stiles and rails with suitable PVC Sheet beading and jointed together with solvent cement as per drawings and specifications as catered in SSR Part – II 2004 complete all as specified and directed.

S & F 100 mm size stainless steel butt hinges, complete all as specified and as directed.

S&F 100mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 100 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and as directed.

S & F 4mm thick figured glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed.

M & L for coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 40 mm thick PCC sub base in cement mortar(1:2:4) type B0 (using 12.5mm graded stone aggregate) and screed bed of 15 mm thick in cement mortar (1:4) complete all as specified and as directed.

M&L for glazed light coloured/printed ceramic tiles 350x250x7mm/450x350x7mm thick in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry pointed in white or coloured cement to match colour of tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

S & F 1000 litres capacity rotational moulded polye-thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I with and including 20mm bore dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S & F GI tubing 15mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S & F GI tubing 20mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S & F 20mm bore, gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe or for union complete all as specified and directed.

S&F bib taps 15mm dia cast copper alloy chromium plated, fancy type with crutch or butter fly handles screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F stop valves/ angular stop valve, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directe.

S&F tubular towel Rail of 20mm dia and 60cm in length, D shaped, with brass chromium plated brackets complete all as specified and as directed.

S & F glass shelf assembly consisiting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed.

S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete all as specified and as directed.

S&F soap dish chromium plated fixed to wall with chromium plated brass screws and plastic cleats complete all as specified and as directed.

S & F 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and laid in trenches complete all as specified and as directed.

M & L for concrete bed in cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) for drain pipes, 110 mm bore including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed.

S & F 110mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S & F 110 mm dia PVC (SWR) bends of any radius complete all as specified and as directed.

S & F 110 mm dia PVC (SWR) bends with access door any radius complete all as specified and as directed.

S & F 110mm bore PVC ( SWR) junction, double (T) equal or unequal complete all as specified and directed.

S & F 110mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S&F Grating doom 100 mm dia of PTMT (min. weight 25 gms) complete all as specified and as directed.

S & F 100 mm dia PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

M&L for point wiring with 1.5 sqmm, single core, PVC insulated and PVC unsheathed FRLS cable, 1100 volts grade IS-694 marked, with multistranded copper conductors and earth continuity wire with 1.5 Sqmm copper conductor cable (including connecting to earth dolly) laid/fixed with and including PVC Casing and Caping on walls/ceiling, and with PVC switch board for mounting switches/socket etc for one light/fan/exhaust fan point controlled by one number one way 5 Amp switch complete all as specified and as directed.

S & F switch piano, flush type single pole one way 5 Amps 230 volt complete all as specified and as directed.

S & F ceiling rose surface bakelite, 65x50mm three terminal complete all as specified and as directed.

S&F LED box type fitting pre-wired including LED tube 1x20W connecting up with aluminium housing and sheathed 1100 volt grade flexible copper cable & fix on PVC block complete all as directed. Make:- Jaquar Model-LGLZ01X020XC/ LGLZ01X020XN/LGLZ01X020XW or Havells Model-LUMILINEPLUSBS20WLED865SPCSS or equivalent model of make Philips /GE/Crompton

S&F Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagonal bulk head black-lit LED10 W -IP-66 luminaire comprising of high brightness LEDs complete all as specified and as directed. Make:- Havells Model HEXAFT10WLED857SSYMBOPC or equivalent Model of make : Philips / Crompton /GE.

S&F PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mmthick plastic laminated sheet cover of size 250 mm x 200 mm and 50 mm deep complete all as specified and as directed.

S&F Sheet metal enclosure with two pin and earth plug and socket complete with one MCB SP upto 32 Amps, having `C` charactristic, breaking cap 10 KA, 240 Volts capacity complete all as specified and as directed.

S & F single pole & neutral DBs 8 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 100 Amp rating copper bus bar complete all as specified and as directed. Make :- Legrand Cat No 5076 11 or equivalent model in Siemens / Schneider

S&F MCBs, SPN 40 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed. Make :- Legrand Model 4086 18 or equivalent model in Siemens / Schneider/L&T

S&F MCBs, SP 6 to 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed. Make :- Legrand Model 4085 90 to 95 orequivalent model in Siemens / Schneider/L&T

S&F RCBOs, double pole ,30mA , 6 to 32 Amps for earth leakage ,overload & short-circuit protection complete all as specified and directed.

M&L for Sub main wiring with 2 runs of 2.5 sqmm, single core, FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dia non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 2.5 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. (Note: 2 run of 2.5 Sqmm cable and 1 run of 2.5 Sqmm cable along with conduit altogether shall be measured as one unit.)

S&F 1100 volts grade heavy duty flat cable of size 16 Sqmm 2 core, PVC insulated aluminium solid conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including replacing 4mm suspension wire complete all as specified and as directed.

S&F ventilating fans AC single phase 230/ 240 V of size 300 mm sweep with louver shutter with frame and necessary fixing accessories , writing MES No. with black synthetic enamel paint 2 cm high in letter complete with necessary connection up including provision of three core copper flexible cable with flexible wire cover of plastic white in colour and connection from ceiling rose to exhaust fan terminal etc complete all as specified and as directed. Make-Usha /Havells/Crompton/ Bajaj.

Supply, fix, Installing and Testing Vertical Storage water heater, with five star rating, rust & shock proof ABS outer body, electric driven of capacity 25 liters, including all accessories complete all as specified and as directed. Make : Havells Model No GHWAMGTWH025 Monza DX or equivalent in Racold/Orient.

M&L for GI bracket made out of 40 mm bore medium grade GI Pipe with two sets clamps, with nuts and bolts, two Nos 90 degree bends all as directed, length of GI Pipe shall not be less than 3.0 metre for fixing of light fittings complete all as specified and as directed.

M&L for plate earthing complete with galvanized mild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than 2.25 m deep below normal ground level) with the top edge of the earth plate at a depth not less than 1.5 m below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and incl GI earth lead wire 4 mm dia or 8 SWG bolted (with GI nuts, bolts & check nuts) and earth plate electrode at one end and connected to main switch board/ DBs etc. at the other, earth strip encased(protected) in and including 15 mm bore GI pipe medium grade with all fittings from top of electrode to main switch board/ DBs etc fixed with and including 25 x 6mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from bottom of earth pit to top of electrode complete with earth pit in PCC 1:2:4 type B-2 using 12 mm graded crushed stone aggregate, RCC cover, funnel, wire mesh including necessary excavation and earth work complete all as specified and shown in electrical plate No 3 of SSR Pt-I complete all as specified and directed.

Dismantling carefully Pressed Steel plate of any size & thick from side wall & bottom of PS tank including nuts, bolts & washers and keeping aside for reuse at site or carrying to store. Note: (a) Serviceable plates shall be segregated and stacked properly in safe custody duly cleaned at site of work for re-use and all other unserviceable plates nut bolts and washers etc shall be removed from site of work as directed. (b) Cost of staging/working platform as involved for the above operation in deemed to be included in the unit rate.

S&F pressed steel plate of Size 1.25M x 1.25M x5.00 mm thick suitable for steel over head tank at 2.5/4 metres high staging as per existing one (as use in bottom side plates) including tightening of Nut, bolt with washers & provision of necessary lead wool/lead pig/lead wire & rubber gasket over and including applying two coats of black bituminous lead free paint (suitable for drinking water) on inner surface and two coats of aluminium paint on outer surface over a coat of red oxide primer after preparation of surface complete all as specified and directed. (Note:-Necessary New nuts, bolts, washers will be measured & paid separately)

Refixing only serviceable PS plate received from item No 76 here in before with nuts, bolts and washers as required quantity and size and new lead wool, black putty of approved make and superior quality for use of drinking water including applying one coats of black bituminous lead free paint (Suitable for drinking water) on inner surface and one coats of aluminium paint on outer surface after preparation of old surfaces complete all as specified and as directed. (Note:-Necessary New nuts, bolts, washers will be measured & paid separately)

dismantling /Cutting including taking down the existing worn out MS plate top cover of pressed steel tank complete all as specified and directed.

S&F MS plain sheet 3.15mm thick with lap joint on roof of PS tank with nuts bolts & washers, welding as required, drilling holes, bending cold or hot, including applying two coats of black bituminous lead free paint (Suitable for drinking water) on inner surface and two coats of Synthetic enamel paint on outer surface over a coat of red oxide primer after preparation of surfaces complete all as specified and directed.(necessary New nuts, bolts, washers will be measured & paid separately)

Refixing only serviceable plain sheet 3.15 mm thick in top cover as obtained from item No. 79 after cleaning/brushing of foreign dust particle plates of PS overhead tank , fixed with necessary nuts, bolts, washers & provision of necessary rubber gasket etc over and including applying one coats of black bituminous lead free paint (Suitable for drinking water) on inner surface and one coats of Synthetic enamel paint on outer surface after preparation of old surfaces complete all as specified and directed. (Note:-Necessary New nuts, bolts, washers will be measured & paid separately)

Dismantling /Cutting Taking down the existing serviceable/unserviceable Joist, Channel, angle or Tee section from pressed steel tank at the height of 2.5/4 metres high staging complete all as specified and as directed.

S&F MS Joist, channel, angle or tee section of grade Fe-410-S cut to required size & shape for bracings, supports & clamps including welding, bending cold or hot, drilling holes and painting with one coat of red oxide primer to each side complete all as specified and as directed.

Refixing of old serviceable mild steel framed work as ladder, cleats as obtained from item No. 82 and similar work in water tank including applying one coats of black bituminous lead free paint (Suitable for drinking water) over a coat of red oxide primer on MS work those are carried out internal side of PS tank & applying one coats of Synthetic enamel paint those are carried out outer side of Tanks after preparation of surfaces complete all as specified and directed.

S&F Mild Steel Screw Bolts of size 16-20 mm (Machine Made) with Hexa-gonal or Square Heads at One End and Screwed the Other or Screwed Both Ends each Screwed End to be fitted with Washers and One Hexagonal or Square Nut, diameter of Shank and Length of Bolt as ordered, complete all as specified and as directed.

Fixing only serviceable Mild Steel Nut & Bolts (Machine Made) with washer as obtained from item 76 above of size 12-16 mm dia after repair/ cleaning properly with Hexa-gonal or Square Heads those are found serviceable from item no 76 above complete all as specified and as directed.

S&F fiber-reinforced plastic scale conventional type water level indicator complete with Mild Steel fabricated scale hiding frame, FRP/GI float, wire float guide pipe, bracket and pulley, counter weight, indicator pin etc including taking out old indicator of any typa complete all as specified and directed. Note: Contractot shall submit purchage voucher alongwith test certificate on execution.

thepfuralie zutso