Construction Work

Amount

Installation Charges inclusive of Transportation to site and the Bored pile equipment employed for the works including setting up of pile driving equipment with all accessories and tools at each of the pile location based on the sequence of operation approved by the departmental Engineers irrespective of the location and distance involved in movement of pile driving equipment etc., complete.

Installation of Vertical Bored cast in situ RCC piles in all types of soils, using Ready Mix Concrete of M 30 grade, with sulphate resistant Cement, fine aggregate, 20mm and down graded HBGS jelly coarse aggregate. The rate includes cost of reinforcing steel, binding wire, fabrication, welding charges, placing of reinforcement cage in bore hole in correct position, cost of boring to the required depth with Bentonite solution with temprory casing of required length, conveyance of RMC to site and pouring concrete using Tremine pipes, conveyance of all materials to the site including all tools and plants, shifting the plants and equipments from one point to another, excavation of mud pits for circulation of Bentonite solution, closing the mud pits to original level and mud removal

with initial lead and lift but excluding dismantling the concrete above the cut off level etc complete as directed by the departmental officers including socketing. The reinforcement cage should be welded properly for lifting. The concrete cubes to be tested as per IS 456-2000. Acceptance criteria by clause 16.1. Frequency of testing should be as per clause 15.2.2. The length of pile for payment shall be measured upto natural ground level. The work should be carried out as per IS 2911. Pile depth should be decided by the departmental officers at site.

450 mm dia pile having longitudinal main reinforcement Of 8 Nos 16# with helical reinforcement at 10 # @ 200mm C/C with inner rings of 12 # @ 1000mm C/C with lifting hook of 12 # at required length.

500 mm dia pile having longitudinal main reinforcement Of 10 Nos 16# with helical reinforcement at 10 # @ 200mm C/C with inner rings of 12 # @ 1000mm C/C with lifting hook of 12 # at required length.

600 mm dia pile having longitudinal main reinforcement of 8 Nos 20 with helical reinforcement at 10 # @ 200mm C/C with inner rings of 12 # @ 1000mm C/C with lifting hook of 12 # at required length.

Initial Load Test as per IS 2911 Part IV 1985 including cost of single pile (250% of pile capacity), labour, reinforcement charges and all other incidential charges including excavation, shoring, strutting, dewatering etc. as necessary hire charges for jacks, measuring devices, Structural Frame work for platform, Kent ledges etc, as required and providing pilecap.

Routine load test as per IS 2911 part IV 1995 (150% of pile capacity) including labour charges for jack, measuring devices, structural frame work plot form, kent ledges etc., as required and as directed by the departmental officers etc. complete.

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling M.sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with Stone Dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Providing pre constructional Anti-termite treatment for the construction of building including cost of chemicals labour as per standard specification. Labour for preparing the area for treatment by spreading chemicals and other incidental charges complete. The rate shall be inclusive of giving anti termite treatment to the building for the following four stages including breaking the termite moulds making holes with crow bars at an interval of 12" to a depth of 8" in the periphery of the building including flooring area and pouring chemicals etc., complete as per ISI 6313/1981.

Cement Concrete 1:5:10 (One Cement, Five M.sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 425 kg/mᶾ and maximum water cement ratio of 0.45, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials)..

Foundation and Basement

For Ground Floor

For First Floor

Second floor

Third floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Providing and Fixing of PVC Trims (Corner beeding) at the outer corner profiles of the tiles including cost of material, labour and handling etc. as directed by departmental engineers at site of work and as per standard specification.

Brick work in Cement Mortar 1:5 (One Cement : Six Sand) using best quality fly ash bricks 230 x 110 x 75mm for Superstructure including curing, etc., complete complying with standard specifiction. Foundation & Basement

For foundation & basement

Brick work in following Cement Mortar using Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS:12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:6 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction. In Cement Mortar 1:6

Ground floor

First floor

Second floor

Third floor

Brick partition walls of 11.50cm thickness using Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Ground Floor

First Floor

Second floor

Paving the floor with best approved quality fine polished Granite Stone Slabs of approved colour of size 1200 x 600 of 18 / 20mm thick with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with matching colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard specification.

Paving the floor with best approved quality lapato Granite Stone Slabs of size 1200 x 600 of 16 / 18mm thick laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with matching colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard specification.

Paving the floor with best brandaed quality Double charged Vitrified anti - skid Tiles of size 600 x 600 x 10mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing and fixing of 2mm thick JEOFLOR PREMIUM + vinyl flooring, 100% recycled flexible homogeneous and monolayer in construction and should be manufactured by calendering & pressing process of size in approved pattern, to ensure a dense, smooth surface and non-directional design, color dyed as a raw mixture to ensure even color throughout the thickness and its surface should be densely compacted for improving wear and ease of maintenance with Anti-bacterial and Fungicidal properties. The flooring shall incorporate a specially formulated PUR+ Surface Treatment and increases the durability of the flooring. It incorporates bacteriostatic and fungistatic actions, tested for Anti-bacterial activity (ISO 22196 → >99% inhibit the growth of bacteria) JEOFLOR or EQUVALENT

Dadooing of wall with Special type of ceramic wall tiles of approved quality, colour and design of size 600x600x8mm thick in all floor over a base layer in CM 1:2, (one of cement and two of sand) 10mm thick and laid in situ, in true alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 to suit the colour of the tiles fixed in position with out any air gap in the tiles etc., complete complying with std. specification and as directed bythe deptl. officers. The colour & quality of tiles should be got appd. by the EE before use on work.

Cladding the vertical wall surface with best approved quality fine polished granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick with machine cut edges laid over a cement mortar bed of 10mm thick using cement mortar 1:2 (One cement and two sand)

Supplying and fixing Ornamental Teak Wood door of overall Size 6.00 x 3.00m with the door opening of 3.00 m & balanced portion fixed both side of shutter made of toughned glass having designed to elegant look .. FRAME : outer frame of well Seasoned Teak wood scantlings of size 8” x 6” with required carvings and rebates to suite the door shutter. .The Frame should be fixed in position with necessary anchorage such as heavy duty holdfasts by dismantling the R.C.C or stone Masonry and redoing the same to the original position with Cement Concrete and adhesive material required for the job so as to keep the frame in vertical position and true to the plumb. The frame should also be embedded into the floor by making necessary dismantling on the floor and redoing the same to its original position after placing the same.

Supplying and fixing solid core flush shutter 35mm thick with Teak ply on both sides, teak lipping alround with necessary adhesive and C.P.screws, including fixing for aldrop , tower bolt, hinges and lock strike plates , putty, fevical etc., and including the cost of aluminium hinges 125x 30mm size -3 Nos. aluminium aldrop of size 250x16mm 1No, Aluminium tower bolt of size 250x12 mm -1 No. , Aluminium tower bolt of size 200x12mm-1 No, aluminium door stopper with Nylon bush-2No. shall be provided. All aluminium furniture fittings are to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 for anodic film thickness of not less than 15 microns. The rate is inclusive of cost of fevical, fixing charges, transportation, loading, unloading all other incidental charges and handling charges etc., complete complying with standard specification.

Single leaf

Double leaf

FRAME:Fully Solid Core WPC-75MMX50MM:Providing and Fixing of Qute WPC/PVC Solid Door frame extruded with size 75mmx50mm.The inner core made of rigid WPC Compound with minimum shore hardness of 55,and Bulk Density 0.8 Grms/Cub.C.mt.The frame shall be fixed fixed to the wall using 10x100mm long M.S.Screw through the frame by using PVC Fasteners.A minimum of 4nos screws to be provided for each vertical member

Supplying and fixing of wood polymer composite (WPC) door with solid door frames extruded with size 75mmx50mm. The inner core made of rigid WPC compound with minimum shore hardness of 55 and buld density 750kg/cub.Mt. The frame shall be fixed to the wall using 10x10mm long MS screw throught the frame by using PVC fasteners. A minimum of 4nos screw to be provided for each vertical members, Door Shutter of 25mm thick Wood Polymer Composite (WPC) single core Extruded Door Shutter, with one side digital printing of specified Design which is approved by engineering-in-charge. Both side of the shutter shall have rough sugar texture finish, laminated with UV oil. The solid WPC board shall have minimum shore hardness of 55 and Bulk density 550kg/cub.Mt moulding the thickness remains 25mm (+/-1mm) etc. complete as per the direction of the departmental officers.(make Qute / Equivalent)

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Providing and Fixing, UPVC factory made, white colour sliding Door made of extruded profiles. Sliding frame 60 mm X 62 mm, Sash 66 mm x 42 mm, Bead 16 x 24.5mm. Profiles of frames and sash will be mitered cut and fusion welded at all corners including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2±0.2mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8mmx100mm long fasteners, all complete as per direction of Engineer-in-charge.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 74mmx60mm x 56mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames with grill and net mesh.

Supplying and fixing of M.S.grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification.

Providing and fixing 2 hr fire rated doubble skin ste door constructed from 1.25mm thick galvanized ste sheet formed to provide a 46mm thick fully flush door shl with lock seam joints at stile edges and the internal construction of the door is a specially designed Honey Comb structure with reinforcements at top, bottom and stile surrounds. As per IS 3614 part-1 & part-2 for stability and integrity and Pressed Galvanized ste confirming to IS 277.

Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Brick Jelly lime concrete 1:2:5(one lime, two sand and five brick jelly) using 40mm gauge brick jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor finish, curing etc., complete complying with standard specifications (for flooring in toilet portions except water closet portions)

Ground Floor

First Floor

Second Floor

Plastering with Cement Mortar 1:3 (One Cement and Three P-Sand) 20mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Treatment to side wall of varying thickness of basement floor, Lift pit, of main building from exterior surface covering the following sequence of operations :

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing and bonding agent Cebex 112,Zydex-Zyecrete 2x or other equivalent compound to be added etc. complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:3 (One Cement and Three P.Sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Supplying and applying of two coats of Putty 3mm thick over the exposed RCC Surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be througly cleaned out of dust and scrubbing the surface shall than be allowed to dry for atleast 48 hours. It shall be than sand papered (Waterpoof abrasive sheet) to give a smooth and even surface. any uneveness shall be made good by applying 1 st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2 nd coat of putty after 6 hours of 1 st coat of putty and then sand papering ( Waterpoof abrasive sheet) the same after its dry and finishing the surface smoothy etc.,complete complying with standard specifiction and as directed by the departmental officers.(The rate inclusive of hire charges for grinding machine with wheel,cost of sand paper(Waterpoof abrasive sheet) cost of putty blade,labour charges for grinding the joints and sand papering,two coats putty,scrapping the putty area to level the surface smooth etc., complete). The putty should be got approved by the Execuctive engineer before use on work.

Painting the wall with Texture Finish Putty including labour charges

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware ovel shaped wash hand basin of size 560 x 450mm including , 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works)..

Without Pedestal

Providing & fixing Stainless Wash Sink of size 600 x 450 x 200mm depth with border width of 50mm icluding folding of edges of approved make, connection pipe of approved make & CP waste coupling over the Granite Platform including providing SS vertical splash board of 600mm ht.along with fixing G.I. waste pipe of 32mm dia ‘C’class Approved make below the sink upto Nahani trap through required fixing arrangement like Jam nut etc. complete as directed by the departmental officers .

Providing and fixing CP bottle trap including cost of materials, labour etc., complete as directed by the departmental officers

Providing and fixing CP health faucet with two in one bip cock (including supply & fixing two way taps including cost of materials, labour etc. complte as directed by the departmental officers.

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position SS Swan Neck Tap of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works.

Supplying and fixing in position UPVC unions of heavy duty of approved quality and good variety of various sizes inluding necessary cutting and threading of UPVC pipes for jointing the union and providing two coats of painting with good variety and approved quality of synthetic enamel paint over one coat of primer in case of pipe line above ground level / one coat of tar in case of below ground level for both internal and external water supply arrangements, etc., complete complying with standard specifications. (The UPVC unions should be got approved by Executive Engineer before use on works).

Supplying and fixing in position UPVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the UPVC pipes dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specification and as directed by the departmental officers. (The UPVC specials should be got approved by the Executive Engineer before use on works). (For both in internal and external water supply arrangements)

Reducer Tee

32mm x 25mm dia

25mm x 20mm dia

20mm x 15mm dia

Elbow

32mm dia

25mm dia

20mm dia

32mm dia

25mm dia

20mm dia

Supplying, laying and jointing CPVC Pipes of approved quality and best variety of pipe of the following dia including labour fixing UPVC Specials, (excluding charges for cutting of pipes, cost of such specials) to wall with necessary teak wood plugs, clamps, screws, UPVC Solution etc., making holes on the walls (or) drilling holes in roof and making good the dismantled portions to original condition with necessray brick work / concrete and plastering wherever necessry with necessary scaffolding charges. complete in all floors complying with standard specification. UPVC pipes shall be got approved by the Executive Engineer before use on works.

Supplying CPVC Specials in water supply arrangements (both in internal and external water supply arrangements

Elbow

Coupling

Union

Supplying and fixing in position the following foam core pipe grade SN8 complete complying with standard specification including cost and conveyance of all material as directed by the departmental officers.

Supplying and fixing in position the following foam core pipe grade SN8 specials complete complying with standard specification including cost and conveyance of all material as directed by the departmental officers.

160mm dia Door Bend

160mm dia Door Elbow

110mm dia Door Bend

110mm dia Door Tee

110mm dia Plain Bend

110mm dia Single Y Junction with Door

110mm dia Cowl

160 mm dia 'Y' with Door

110mm dia Elbow with Door

Construction of Manhole chambers at various depths including earthwork excavation as per S.S - 20 B, crushed stone sand (M-sand) filling, laying of C.C 1:5:10 using 40mm HBGS Jelly for foundation and Brick work in C.M 1:5 for side walls, plastering the wall outer side in c.m 1:4 (12mm thick) and inner side in c.m 1:3 (20mm thick) and providing manhole chambers with SFRC frame with cover, providing C.I steps inside the chambers etc., complete

Clear size of 0.60x0.60x1.20m

Clear size of 0.90x0.90x1.20m

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing approved best quality aluminium anodised towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Providing the safeguard for the columns for 1m height with rubber corner guard of 3"x3" L type colour of black and yellow approved quality etc. complete complying with standard specification and as directed by the departmental officers.

Paving the floor with Tactile Paver Type of New Tek BT Yellow Colour Ceramic Tiles of size 305 x 305 x 15mm for Vision Impairment Person laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing of cylindrical vertical notational polythene water storage tank confirming to IS. 12701 / 96. The tank is meant for outer (or) indoor, use complete with removable hinged top locking arrangements and to make provision to fix with simple pipe lines necessary manhole with cover and including all PVC specials, plugs, screws, nails to fix the tank, and the tank should be fixed firmly. The rate shall inclusive of all materials labour, conveyance, hoistings and fixing charges etc., complete complying with standard specification and as directed by the departmental officers. (The water tank should be got approved by the Executive Engineer before use on works by the Departmental Officers.

Supplying and fixing of 5 H.P submergible Pump set of approved brand etc complete complying with standard specification and as directed by the departmental officers.

Suppling and fixing position of polycorbonate sheet (Opaque White) roofing with following specification. The roofing made of 10 mm thick multi wall polycarbonate sheet roofing with following specification. The roofing made of 10mm thick multi wall polycarbonate sheet with approved colour (Lexan branded) double sided UV coated using MS frame work consists of main truss 50 x 50 mm MS square pipe for vertical support in the base plates and top connecting plate for fixing truss. The rate including cost of 10mm thick multi wall polycarbonate sheet, MS truss work, MS vertical support pillars, Horizontal purlins, Aluminium plate for bottom & top with sealent for all joint of sheets and labour charges for all fabrication works and sheet fixing work and necessary Scaffolding cost and painting work for all MS Truss with purlin etc., completed. and as directed by departmental officers.

Supplying and fixing Hydraulic Door Closer of various sizes of approved quality using Aluminium Extruded section body tubuler type universal hydraulic door closer with double speed adjustment like HARDWYN make GAZEL (or) equivalent (with ISI Monogram)

Plain Cement Concrete 1:1-1/2:3 for levellling course screed (one cement, two sand and four hard broken stone jelly) using 6-10 mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Single nosing to the the granite slabs by cutting the granite slabs for 18mm to 20mm thick edges semicircular shape to required size and nosing with semicircular shape and polishing using hand machine and the nosing is made highly smooth and glossy.The cost includes labour charges and cost cost of machineries and polishing charges,etc.,complete as directed by the departmental officers.

Dismantling, removing and carefully stacking Brick/stone masonry in lime mortar walls under 3m high etc., complete complying with standard specification and as directed by the departmental officers at site of work.

Dismantling, removing and carefully stacking RCC etc., complete complying with standard specification and as directed by the departmental officers at site of work.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box inflush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )

Wiring with 2 x 1.5 Sqmm. (22/0.3) PVC insulated SC unsheathed cu. Conductor with of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 6A Modular switch with surface box and covered with modular plates with suitable colour for open PVC light point (5 points per coil) ( Anchor Roma/Hager/equ)

Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End.

Supply and fixing of 20W, 4 feet LED fitting on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of WT bulk head fitting with guard suitable for 11W CFL lamp with CFL.

Supply and fixing of 1200mm (48") sweep AC ceiling fan 5 star rated complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 600mm down rod on the existing fan clamp

Supply and fixing of 300mm (12”) sweep (light duty) AC Exhaust fan without provision of hole in the wall.

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan.

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting.

Supply and fixing of 1000W automatic electric water heater of 25 litres capacity suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flex wire,but without plumbing work.

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End.

Supply and fixing of 2 no. 6A two module socket, 1no.6/16 A two module socket , 2 nos. 6A one module switch, 1 nos. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End.

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug)

Supply and fixing of 32A DP MCB in sheet steel enclosure with concealed on wall with earth connection

Supply and fixing of 63A FP MCB in sheet steel enclosure with concealed wall with earth connection

Supply and Run of 2 of 4 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm.PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.

Supply and Run of 2 of 6 sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.

Supply and run of 4 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable colour.

Supply and Run of 4 of 10 sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour.

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only.

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution boardwith double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB asoutgoing in flush with wall with earth connection only.

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal /acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 3 nos. 32A 3P MCB , 15 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only.(The DB and MCBs are of Hager make/Eq.)

Supply and clarnping of 3-1/2 x 50 PVC LTUG armoured cable on post or on wall with MS clamps

Supply and providing cable end termination of 3-1/2 x50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and fixing of brass cable gland for 3-1/2 x 50 sq.mm. PVC armoured LTUG cable with earth connection

Supply and laying of 31/2 x185 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and laying of 2R 31/2 x185 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and providing cable end termination of 3-1/2 x185 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and fixing of brass cable gland for 3-1/2 x 185 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and fixing of 63A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses doublebreak on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply, Erection, Testing & Commissioning of 400 A capacity cubical type panel board 8.3X5.5X1 dust and vermin proof made of 16SWG sheet steel for outer body and stiffness and doors with main switches supports respectively of the following cubical mounting main switches with center bus bar chamber and vertical covers, and cable chamber on both side of the bus bar chamber at the extreme ends on both side and confirming in I.S specifications suitable for floor mounting type. 400 A Incoming - 1No 250 A Outgoing - 4Nos 125 A Outgoing - 2Nos (Incoming) 400A TPN switch disconnector fuse units interior switch only with HRC fuse double break -1no,- Hager Legrand /L&T /siemens /Equ. (Out Going) 250A TPN switch disconnector fuse units interior switch only with HRC fuse double break -4 no,- Hager Legrand /L&T /siemens /Equ. 125A TPN switch disconnector fuse units interior switch only with HRC fuse double break -2 nos,- Hager Legrand /L&T /siemens /Equ. Space for fixing display board. A Separate chamber on Top of one side should be built with one set of multi meter,[ammeter, volt meter, Hz.)

Meter with R Y B LED pilot lamps set with fuse base, top with 10A HRC link for 3 phases and CT coil (Siemens) the bus will have suitable 4 Nos. of 50 x 6mm bus for phase and 25x3 mm earth bus all round the panel to provide earth connection to the cubical switches cable glands cable adopter box etc, bus should be mounted on synthetic enamel compound bus supports at equal interval as per IS specifications. The incoming 400A TP switch should be connected with 50X6 mm to the bus,250A switches with 37x6mm flat and 125A Switches with 25mmx6mm bus of rigid copper flat. The switches should be separated by 6mm thick hylem sheet separators and properly (double) earthed as per IE rules, CEIG specification. The panel should be Powder coated, the cable size capacity of switch location etc., should be marked with white paint and 2 Nos. metallic danger board affixed complete with mounting on base channel supportS.

Supply, Erection, Testing & Commissioning of 250 A capacity cubical type panel board dust and vermin proof made of 16SWG sheet steel for outer body and stiffness and doors with main switches supports respectively of the following cubical mounting main switches with center bus bar chamber and vertical covers, and cable chamber on both side of the bus bar chamber at the extreme ends on both side and confirming in I.S specifications suitable for floor mounting type. (Incoming) 250A TPN switch disconnector fuse units interior switch only with HRC fuse double break -1no,- Hager Legrand /L&T /siemens /Equ. (Out Going) 125A TPN switch disconnector fuse units interior switch only with HRC fuse double break -4 no,- Hager Legrand /L&T /siemens /Equ. 63A TPN switch disconnector fuse units interior switch only with HRC fuse double break -2nos,- Hager Legrand /L&T /siemens /Equ. Space for fixing display board. A Separate chamber on Top of one side should be built with one set of multi meter,[ammeter, volt meter, Hz.

Meter with R Y B LED pilot lamps set with fuse base, top with 10A HRC link for 3 phases and CT coil (Siemens) the bus will have suitable 4 Nos. of 37 x 6mm bus for phase and 25x3 mm earth bus all round the panel to provide earth connection to the cubical switches cable glands cable adopter box etc, bus should be mounted on synthetic enamel compound bus supports at equal interval as per IS specifications. The incoming 250A TP switch should be connected with 37X6mm to the bus and 125A Switches with 25mmx6mm bus of rigid copper flat.,63A witches with 8SWG copper rods The switches should be separated by 6mm thick hylem sheet separators and properly (double) earthed as per IE rules, CEIG specification. The panel should be Powder coated, the cable size capacity of switch location etc., should be marked with white paint and 2 Nos. metallic danger board affixed complete with mounting on base channel supports.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground forearth connection.

Supply and Installation of 2.0 TR capacity 3 star rated energy efficient Hi wall mounting Split type Air Conditioner unit consisting of out door condensing unit complete with hermetically sealed Air compressor with R 22 refrigerant air cooled condenser, fan etc., and 1No Indoor Hi wall mounted 2.0 TR capacity evaporator unit complete with cooling coil, blower motor and connected accessories, control etc, with 3 metre copper refrigerant piping and chord wire connecting indoor and out door unit with drain pipe suitable for operation on 230V+ 10% 50 HZ single phase AC supply.(Make: Carrier/Equ)

Supply and laying of 5/8” and 3/8” copper with insulation etc., ( beyond the standard length of 3mts)

Supply and fixing of 5 KVA Automatic voltage stabilizer with time delay arrangements for operation on 230V 50C/S AC supply (Make V-Guard/Equ)

Supply and fixing of out door base stand for split AC unit

Supply, Erection, Testing, Commissioning and Handing over of 26 Persons Capacity with gear less machine room model mini space bed cum passenger Lift as per following technical specifications including all taxes and duties. Technical Specifications: 1. Location: Cancer Block Front Side Lift 2.No of lift: one no 3.Type of lift: Bed cum passenger lift, Machine Room 4.Capacity of lift: 26 persons/1360 Kgs 5.Speed: 1m / sec 6.Type of drive: V3F drive with enhanced ride comfort and near zero level functions 7.No of floors: GF+2 Floor 8.Total travel: 9 mts approximately 9.Leveling accuracy: high level accuracy with smooth and jerk free stopping

10. Construction of CAR: No.3 hardened sheet high quality stainless steel car and hand rail granite flooring and Perspex false ceiling with LED light fitting 11. Position of machine: Inside the Shaft 12. No of landing service: One in each floor front side- 3 no’s 13. No. of car entrance: one in the front side only 14. Car entrance door: power operated automatic V3F drive center opening sliding SS door 15. Landing entrance door: power operated V3F drive center opening sliding SS door with provision for emergency exit key at all landings. 16.Lift well Size : 1300 mm (wide)x 2400 mm 19. Car clear opening: 1200 mm wide x 2000 mm height. 17.Lift pit depth:1600 mm 18. Car size: 1600 mm (width)x2400 mm (depth) x 2200 (Height) 19. Car clear opening: 1200 mm wide x 2000 mm height. 20.Lift machine room size: Not Applicable 21. Power supply: 400 / 440 v three phase 50 Hz AC supply for power and 230 V 50 Hz single phase power supply for light.

22.Control: micro computer (micro processor):based simplex collective control with / without attendant 23. Car fittings: LED lighting with 2 nos 300 mm sweep cabin fan. 24. Lift well: RCC construction with brick masonry existing. 25. Induction: UP / DOWN digital direction and position indicator for all landings and inside the car. 26.Emergency alarm bell: battery operated bell to be provided with automatic charging device 27.Emergency light: battery operated light to be provided with automatic charging device 28.Fire mans switch: to be provided at the GF 29. Minor builder works: to be provided by the lift contractor. 30. Scaffoldings: to be provided by the lift contractor. 31. Sill angles and facia plates: SS to be provided by the lift contractor. 32. Steel for lift machinery: to be provided by the lift contractor. 33. Servicing and maintenance: free comprehensive servicing and maintenance for one year Guarantee period to be provided by the lift contractor.

34. Automatic rescue device: to facilitate the landing of the nearest floor at the time of power failure this shall consist of suitable battery system with charger inverter under voltage protection system etc. complete with all accessories. 35. Provision for intercom with phone: to be provided by the lift contractor..Lift license: preparation of drawings payment of charges to CEIG and insurance policy and obtaining CEIG approval for the lift as per lift act should be done by the lift contractor 37. Floor position announcer: to be provided by the lift contractor. 38.Special features a) Infra red door sensor with full height screen b) Full width half height rear panel mirror c)Tubular SS hand rail in car d) Stainless steel signal features e) Vandal proof SS button with SS cover f) SS door frames for landing doors g) V3F door operator h) Call register signal

i) Stainless steel facia plates for car operating panel and landing fixtures j) Steel ladder for lift machine room k) On / off switch for fan and light l) Over load warning indicator with audio announcer m)Voltage stabilizer for control circuits n)Braille button o) Pit ladder and Balustrade assembly 39.Over speed governor phase failure and phase reversal relay alarm bell T guide brackets for car and counter weight rubber padding under the winding unit motor of adequate capacity signal reduction worm gear electromagnetic brake with compression springs car safety gears buffers electro mechanical locks emergency key side supporting angles motor over load protection devices final limit switch main suspension ropes counter weight lifting joist for mounting the machineries

40. Guarantee: guarantee at least for one year for the material and workman ship of equipments should be offered by the lift contractor. 41. Site testing in accordance with IS 14665 should be carried out at the time of handing over to the user department 42. Supply operation and maintenance manual and necessary tools for operation and a set of Spare parts required for one year.

GST at 18%

SRI PATHY ASSOCIATES PRIVATE LIMITED (BID ID -1082857)

SEA ROCK INFRASTRUCTURE (BID ID -1082893)