SPECIAL REPAIRS TO BLDG NO T-2, BLDG NO P-26A, BLDG NO P-23/L/P/103A IN RMS AND PROV OF TOILET (LADIES CUM GENTS) NEAR ADMINISTRATIVE BLOCK BLDG NO 101 RMS AT AJMER MIL STN

Amount

Demolition of Lime concrete / cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down chowkats or frames area not exceeding 1.50 Sqm (w/o taking off shutters from frames) and removing from site, complete all as specified and as directed.

Taking down chowkats or frames area exceeding 1.50 Sqm and not exceeding 4.00 Sqm (w/o taking off shutters from frames) and removing from site, complete all as specified and as directed.

M & L for vitrified ceramic dark tiles 10 mm thick (square/rectangular) polised area of each tile exc 0.36 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles over and incliding screed bed 15mm in CM (1:6) complete all as specified and directed.

M & L for vitrified ceramic dark tiles in vertical surface such as skirting/dados etc 10 mm thick (square/rectangular) polised area of each tile exc 0.36 sqm etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles over and incliding 10mm thick CM (1:4) as in backing coat complete all as specified and directed.

M & L for Non - skid coloured ceramic tiles 400x400x 7 to 8 mm thick (square), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M & L for Non - skid light coloured ceramic tiles of size 600x600x7-8mm thick in floors etc. set and jointed in neat cement slurry and inted in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M & L for Non-Skid light coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.18sqm but not exceeding 0.38 sqm in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles over and incliding 10mm thick CM (1:4) as in backing coat complete all as specified and directed.

M & L for Non - skid coloured ceramic tiles 400x400x 7 to 8 mm thick (square), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M & L for Coloured glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 300X 7mm thick thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick cement plaster in ement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed.

M & L coloured Glazed ceramic tiles in vertical serfaces 450 x 300 x 7 mm thick set and jointed with Balendura adhesive or equivalent and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing for tiles, complete all as specified and directed.

M & L for Machine cut kota stone slab flooring of size 550 x 550 x 18-22mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete, over and including cement screed bed 15 mm thick in cement mortar (1:6) base including rubbing and mirror polishing, and half nose moulding (bull nosing) etc, complete all as specified and directed.

All as per item above 13.00 but pre-polished kota stone as in vertical surfaces such as skirting and risers over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces, complete all as specified and directed.

M & L for Granite work (Jet/Telephonic Black) 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, counter basins, urinal partitions etc. and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces and half nose moulding (bull nosing) etc, complete all as specified and directed.

M & L for 50 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished without using extra cement complete. Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

M & L PCC (1:4:8) Type D-2 using 40 mm graded stone aggregate in foundation, filling and mass concrete and sub base surface finished even & fair complete all as specified and directed.

M & L for Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over 50mm thick Sand cushioning layer etc complete all as specified and as directed.

M & L for Vitrified out door tiles 40 cm x 40 cm x 10-12 mm thick digital design set, jointed and pointed in neat cement slurry as in floors with grey cement over & including over screed bed or bedding layer of mortar 20 mm thick Cement Mortar 1:6 complete all as specified and directed.

M & L for PCC 1:2:4 type B-1 ( using 20mm graded mechanically crushed stone aggregate) as in bed blocks, copings, apex stones,side of interlocking tiles etc complete all as specified and directed.

Dismantling Asbestos cement (corrugated of semicorrugated etc), any gauge, thickness, roof coverings complete all as specified as directed.

Dismantling Plain or corrugated steel sheeting,any gauge, thickness, including Single layer Mangalore pattern or similar tiles in roofing roof coverings complete all as specified as directed.

S & F for pre-painted galvatume aluminium zinc coating (AZ-150) GI based corrugated steel sheet 0.50 mm thick of any colour having 550 Mpa tensile strength as in roof covering/cladding and fixed with self tapping screws, complete all as specified.

S & F for pre-painted galvatume aluminium zinc coating (AZ-150) GI based plain steel sheet 0.50 mm thick of any colour having 550 Mpa tensile strength as in roof covering/cladding and fixed with self tapping screws, complete all as specified and directed.

Dismantling unframed timber fillets, rails, posts, rafters, purlins etc under 40 sqcm in section complete all as specified as directed.

S & F for steel work in tublar truss including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 grade st 240 etc confirming to fe-410-W (Gde-E-250) quality-A all as specified as directed.

Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 65 mm x 125 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed, complete all as specified and directed.

Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 45 mm x 70 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed.

S & F for factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N / m2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fie retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and directed. (Note : Stainless steel butt hinges and necessary SS screws shall be paid separately).

S & F for 2nd class hard wood 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treatedsupplied and fitted to chowkats complete all as specified and directed.

S & F for IInd class (hollock) hard wood factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed.

S & F for factory made Steel window/ ventilator glazed & gauged (combination) with side hung/ top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete incl necessary cooler arrangement in window & guard bars all as shown in drg No. CEBZ/TD/14/11 sh No 1/7 to 7/7 & complete all as specified and directed.

S & F for 4.8 mm thick plain or tinted glass, ordinary quality and glazing rubber beading in square n exc 0.5 sqm in each pane complete all as specified and directed.

S & F for 5.5mm thick sheet glass plain / pin headed, ordinary quality and glazing with oil putty in square nexc 0.50 Sqm in each pane complete all as specified and directed.

S & F for 3.0 mm thick sheet glass, ordinary quality and glazing with oil putty in square not excc 0.5 Sqm in each pane complete all as specified and as directed.

S & F 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S & F for 150 mm long 10mm dia Extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S & F for 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed.

S & F for alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified and directed.

S & F for double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber complete all as specified and directed.

S & F for MS helical door spring 300mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats complete all as specified and directed.

S & F for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified and directed.

S & F in repairs stainless steel type curtain rod 22 to 25mm dia as per sample complete all as specified and directed.

S & F in repair of purpose made brackets trade pattern for stainless steel decorative type curtain rods suitable for holding 22 to 25mm dia complete all as specified and directed.

S & F in repair of stainless steel decorative fincals(round type with mirror optic finish)trade pattern for decorative type curtain rods suitable for 22 to 25mm dia curtain rods complete all as specified and directed.

S & F in repair of stainless steel decorative fincals wall to wall trade pattern suitable for decorative type curtain rods 22 to 25mm dia complete all as specified and directed.

Demolition of brickwork or stone/boulder masanory,laid dry below or above ground level and removing material from site complete all as specified and directed.

M & L brick work with old size fly ash bricks straight or curved on plan exc. 6 M mean radius built in CM 1:6 complete all as specified and directed.

M & L for Brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster from brick walls/stone masonry walls, concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.

M & L for rough cast plaster using crushed stone of size between 6 mm to 10 mm, coarse sand and cement mixed in the ratio of (1:1:1) over and including rendering coat of 15 mm thick on fair faces of brick work or concrete surfaces or stone masonry surfaces or other than fair faces of brick work or on one side of lathing (on vertical surfaces) in cement mortar 1:4 finished even and fair including two coats of cement base paint complete all as specified and as directed.

M & L for 5 mm thick cement plaster in cement mortar 1:3 on ceiling, finished even and smooth without using extra cement all as specified and directed.

M & L for 10 mm thick cement plaster in cement mortar 1:3 on ceiling, finished even and smooth without using extra cement all as specified and directed.

M & L for for 15mm thick rendering in cement mortar (1:6) on brick/stone masonry or concrete surfaces (internal walls) of any description, finished the surface even and smooth without using extra cement complete all as specified and directed.

M & L for for 15mm thick rendering on fair faces of brick work/stone masonry, concrete surfaces (external walls) or stone walls upto tripple storey bldgs in cement mortar 1:4 mixed with liquid water proofing compound using as per manufacturer’s instructions, finished even and fair, complete all as specified. Note : WPC shall be measured and paid separately.

Supply only liquid water proofing compound, ISI marked complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper paint over a coat of 1mm thick JK/ Birla putty complete all as specified and directed.

M & L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M & L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of oil bound distemper on walls over a coat of 1mm thick putty complete all as specified and directed.

M & L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applyingTwo or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

M & L for two coat of synthetic enamel painting to new wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer complete all as specified and directed.

M & L for two coat of synthetic enamel painting to steel surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of red oxide primer complete all as specified and directed.

S & F of framed work such as grills, gratings, cooler stands etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 incl necessary fixing to walls complete all as specified and directed.

S & F for in repair 125 mm dia oval shape brass handle fancy type bright finish complete all as specified & directed.

S & F for in repairs 30 mm when Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S & F for in magnetic ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

Demolition and breaking up of rain water pipe /UPVC pipe line 100mm/75mm dia incl all fittings, complete all as specified and directed.

S & F for for 110mm dia UPVC, soil waste drain pipe, type ‘A’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in floors or walls etc complete all as specified and directed. (Note- Rubber rings for pipes and fittings shall be conforming to IS 5382-1985)

S & F for for 75 mm dia UPVC, soil waste drain pipe, type ‘A’, conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint fixed to wall/floors etc complete all as specified and directed. (Note- Rubber rings for pipes and fittings shall be conforming to IS 5382-1985)

S & F for 110 mm bore UPVC (SWR) bend with access door including jointing with solvent cement, complete all as specified and directed. (Note- UPVC bends shall be conforming to BS 4515 DIN 19531 and DIN 19534)

S & F for 110 mm bore UPVC (SWR) ( singleT) equal or unequal including jointing with solvent cement, complete all as specified and directed.

S & F for PVC (SWR), junction single, (Single T) equal or unequal 110mm dia complete all as specified and directed.

S & F for 110 mm bore UPVC (SWR) branch piece,single ( singleY) equal or unequal including jointing with solvent cement, complete all as specified and directed.

S & F for 75 mm bore UPVC (SWR) bend including jointing with solvent cement, complete all as specified and directed. (Note- UPVC bends shall be conforming to BS 4515 DIN 19531 and DIN 19534)

S & F for in repair PVC (SWR) 75 mm bore branch piece (Tee) fixed to walls with cement joint with or w/o ovel access door complete all as specified and directed.

S & F for PVC (SWR), junction single, (Single T) equal or unequal 75mm dia complete all as specified and directed .

S & F for in repair PVC (SWR) 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S & F for PVC (SWR) vent cowl 110mm dia complete all as specified and directed .

S & F for PVC in repair(SWR) 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S & F for PVC (SWR) vent cowl 75mm dia complete all as specified and directed .

M & L PVC (SWR) floor trap 75mm dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

M & L PVC (SWR) floor trap 110mm dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

M & L for in repairs 75mm diaPVC (SWR) floor trap with grating including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate complete all as specified and directed.

M & L PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement complete all as specified and directed .

M & L for in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

S & F for brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges all as specified and directed. (Make: Jaquar Essco/Prayag/Plumber/Jal)

S & F in repair for pvc bathroom mirror cabinet of size 127mmx343mmx546mm wall mounted incl all fiittings complete all as specified and directed.

S & F for low density polyethylene pipe connection with PTMT nuts suitable for 15 mm bore GI pipe 450 mm long of pressure rating 6 kg/cm² including brass union and washer ateach end, one end screwed to inlet of piller tap/cistern and other end to stop cock etc complete all as specified and directed.

S & F waste pipe & pipe coupling chromium plated size 32 mm with long thread complete all as specified and directed.

S & F for in repairs Vitreous China W.H.B. white of size 550 x 440 mm, incl waste pipe and brackets etc complete all specified and all directed.

S & F for in repairs Vitreous China W.H.B. white of size 550 x 440 mm, incl waste pipe and brackets etc complete all specified and all directed.

S & F for in repairs Chromium plated brass pillar tap of size 15 mm in WHB/Kitcen sink etc complete all specified and all directed.

S & F for Chromium plated brass pillar tap of size 15 mm in WHB complete all specified and all directed.

S & F for in repairs vitreous china premium quality/1st quality wash down water closet EWC with complete one set white ( incl all necessary accesories like rag bolts/gel gasket etc.(excluding flushing cistern & flush pipe ) with ‘P’ or ‘S’ trap of dia 100mm including provn of cement concrete bedding complete all as specified and directed. Make : Jaquar/Cera/Hindware/Parryware

S & F for Polymer coloured (Polypropeylene Delrin and ABS) low level flushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS derscription mark with 2731 with and including suitable size of MS brackets, plug, screws all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed.

S & F for plastic water closet seat white, closed pattern with flat bottom and cover and mild steel C.P. or Aluminum hinging device complete all as specified and directed.

S & F for in repair 15mm bore angle valves fancy type, chromium plated cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union all as specified and directed.

S & F for in repair stop valves concealed type, 15mm dia fancy type, chromium plated with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and directed.

S & F for in repairs 15mm bore bib tap cast copper alloy CP with crutch or butterfly handles screwed down for iron pipes or for brass ferrule complete all as specified and directed.

S & F for 15mm bore bib tap cast copper alloy CP with crutch or butterfly handles screwed down for iron pipes or for brass ferrule complete all as specified and directed.

S & F for in repair CP brass soap dish complete all as specified and directed.

M & L for Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified and directed.

M & L for Rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified and directed.

S & F 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore all as specified and directed.

S & F for gun metal gate valves, with iron wheel head, screwed both ends for iron pipe flange ends type fixed of 20mm dia all as specified and directed. (Make-Zoloto/NMC/Leader).

S & F for in repairs 20mm bore Gun-Metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F for 20 mm PTMT ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes all as specified and directed. (Make-Prayag/Polytuff)

S & F for in repair PTMT ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes all as specified and directed.

Taking up or down 15mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 20mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the complete all as specified and directed.

S & F for solid PVC frame of size 50 mm x 47 mm made out of 5 mm single side prelam PVC sheet & edges will be printed to match with prelam sheet rein forced with MS square tube etc. complete all as specified and directed.

M & L CPVC tubing 15 mm dia medium grade galvanized with all fittings and fixed complete to brick/stone wall or laid in floor concealed complete all as specified and directed. (Make: Astral/Prayag/Finolex/Ashirwad)

M & L CPVC tubing 20 mm dia medium grade galvanized with all fittings and fixed complete to brick/stone wall or laid in floor concealed dia complete all as specified and directed. (Make: Astral/Prayag/Finolex/Ashirwad)

Dismantling of ceiling board/lathing any thickness including frame work complete all as specified and directed.

Providing & Fixing false ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as complete all as specified and directed.

S & F for M S plate or angle, channel, square cut or notched with riveted, bolted or welded attachment completed all as spd and directed.

S & F IInd class hardwood Chowkhats and frames plain solid , straight wrought, framed rebated on the solid rounded or chamfered, put together with glue, pinned at joints complete all as spescified and directed.

S & F 1st class teakwood plain,solid,curved chawkats and frames,wrought,framed rebated on the solid rounded or chamfered put together with glue pinned at joints incl PU polishing using high pressure spray gun mirror finish on surface of any description width or girth incluidng cleaning and preparing the surface after applying a coat of wood filler on new works with two or more coats of PU polish complete all as specified and directed.

S & F for 18/19mm thick Block boards, grade 2 quality, interior grade, commercial type, and both faces is covered with approved pattern decorative coloured laminate type 1 of 0.9mm thick, and all around side faces is covered with decorative lipping complete prepared as cup board shutter and fixed with wooden frame-work complete alll as specified and directed.

M & L for preparation of old painted wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

M & L for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

M & L for rolled mild steel work angle iron as in door frame (Chowkhats) including provn of 10mm dia deformed bar welded horizontally to bottom of frame conforming to Fe-290 ( Gde 165-E ) including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed.

S & F for hold fast of flat iron conforming to Fe-290 (Gde-E-165) including preparing the surfaces & treated with two coats for coaltar & sanded with clean sharp sand complete all as specified & directed.

S & F for Jet flush including plate & PVC connection complete all as specified and directed.

S & F for IInd Class Hard wod small fittings such as brackets of any type, latch and hinges blocks , shaped door and window stops and the like, incl all necessary labours; article n.exc 200cum each complete all as specified and directed.

S & F for MS butt hinge 50mm medium weight cold rolled incl necessary welding etc complete all as specified and directed.

S & F Add extra for 6mm thick external teak wood lipping 18/19mm and fixed with nails complete all as specified and directed.

S & F 100mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F for 100mm aluminium handles, cast type, anodised complete all as specified and directed.

S & F for aluminium handle size & shape as per existing handle for aluminium door or 150 mm long etc. complete all as specified and directed.

Taking down shutters exceeding 1 Sqm and not exceeding 2 Sqm and removing from site, complete all as specified and as directed.

Taking down shutters not exceeding 1 Sqm and removing from site, complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/ slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

S & F for Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

S & F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed.

Taking down aluminium door shutter of size exc 1.5 Sqm and n exc 4 Sqm each leaf, opening floor spring assembly over hauling, refixing floor spring (with new screws) and door shutter in position complete all as specified and directed.

M & L for powder coated Anodised Aluminium frames for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified and directed.

M & L powder coated aluminium door shutters, aluminium sectionminium thickness 3mm including necessary joining cleat, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etcincl taking down old aluminium door shutter complete all as specified and directed.

M & L powder coated aluminium window shutters, any type (sliding, side hung, fix etc) ( three track) aluminium section minimum tickness 3mm including necessary joining cleat, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc incl taking down old aluminium window shutter complete all as specified and directed.

M & L for 1 mm thick 100 mm dia Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges complete all as specified and directed.

Providing precast cement concrete type C0(1:3:6) louvres and jallies, 25 mm thick (mea sured solid), including all mouldings but excluding frame set in cement mortor 1:6 including necessary form work complete all as specified and directed.

S & F for in repairs Toilet paper holder with flat recessed type stainless steel fixed to walls with chromium plated (CP) brass screws l complete all as specified and directed

S & F for in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed.

S & F for in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

M & L for 12 mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required incl sand itching on door for embelem size upto 0.2 sqm in middle rail of door with heavy duty SS 304 hinges of size 150mm and SS 304 heavy duty D bracket for door corner protection complete all as specified and directed.

M & L for glass door lock for toughned glass thickness 12 mm having ultra keys(03 Nos) outside 7 knob inside with screws satin finish witrh striking box SS grade 304 complete all as specified and directed.

S & F for in repairs brass 2 levers Locks for cupboard,grade-I, size 50 mm with keys complete all as specified and directed.

S & F for 150 mm long Brass handles, cast type, polished bright complete all as specified and directed.

S & F for in repair brass, sliding door bolt length 300mm with sand or die-cast brass hasp,staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed.

M & L Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick SS sheet foundation box, main body with stainless steel cover,governing pivot made of brass,other parts made of stainless steel heavy duty(SS 304) and complete all as specified and directed.

M & L for for preparation of newly plastered surface of wall and applying two coats of cement base paint complete all as specified and directed.

M & L preparation old decorated surfaces of walls and providing one coat of cement base paint complete all as specified and directed.

M & L for for preparation of newly plastered surface of ceiling and applying three coats of white wash complete all as specified.

S & F for 15mm bore angle valves cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union all as specified and directed. (Make: Jaquar Essco/Prayag/Plumber/Jal)

S & F for in repair 15mm bore two angle valves fancy type, chromium plated cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union all as specified and directed.

Taking down existing water proofing treatment of any description incl PCC padding, cement plaster any thickness from roof surfaces, cleaning of roof and prepairing it for further treatment incl make good necessary dubbing out wherever required and removing rubbish from site complete all as specified and directed.

M & L for screed plaster 10mm thick in CM (1:4) on fair faces of brick work or concrete surfaces mixed with WPC incl necessary doubingout etc finished even and smooth for laying WPT without using extra cement complete all as specified and directed.

M & L for coved fillet in PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate at junction of roof & parapet wall and other vertical surfaces 75mm radius and surface painted with a hot paving bitumen grade 30/40 conforming to IS-73 @0.70 Kg/Sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr Sqm complete all as specified and directed

M & L for APP modified polymeric water proofing membrane, 3mm thick having centre core not less than 100 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3.00Kg/Sqm applied with bonding material using blown type bitumen conforming to IS-702 grade 85/25 @1.20 Kg/Sqm over bitumen primer conforming to IS-3384 @0.40 Kg/Sqm with final coat of bonding bitumen grade 85/25 @1.20 Kg/Sqm over APP membrane with all overlaps complete all as specified and directed.

M & L for PCC 40mm thick (minimum Consolidated thickness) Type B-0 (1:2:4), using 12.5 mm graded crushed stone aggregate as in padding finished even and smooth without using extra cement with existing slope with V shaped groves 6mm wide and 10mm deep @ 0.60 metre spacing both bays or part there of on top of padding and filled with mastic bitumen of 1:1 preparation complete all as specified and directed.

M & L rendering 5 mm thick in CM 1:4 on concrete surface of ceiling & finished even & smooth without using extra cement complete all as specified and directed.

M & L for 10mm thick rendering on concrete surfaces of roof projection cornices & chajja etc finished fair and even without using extra cement including WPC in CM 1:4 incl taking down existing cement plaster and including necessary arrangements to work on roof projection, cornice & chajja etc complete all as specified and directed.

Demolition, reinforced cement concrete roofs, floors (other than ground floors), beams, staircases, landing, parapets, chajjas, and similar suspended work cut as required to facilitate demolition complete all as specified and directed.

M & L for RCC 1:2:4 Type B0 using 12.5mm graded aggregate as in beams, cantilevers, bressummers, parapets, chajjas, lintels over 1.5m span etc, excluding formwork complete all as specified and directed.

M & L for for repair to RCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in columns,footings/plinth beam etc excluding necessary formwork complete all as specified and directed.

M & L for for providing reinforced cement concrete 1:2 :4 type B1 using (20mm graded stone aggregate ) as in cooking platform,roof slabs supported on wall, beam, cantilevers and kitchen cooking platform excluding necessary formwork complete all as specified and directed.

S & F for in repairs stainless steel sink , made out of 1.00mm thick sheet for kitchen oe laboratory with plug,washers, waste pipe, cast irn cantilever bracket incl bedding in cemen t mortar on dwarf wall or incl fixing cantilever brackets and connecting union to pipe incl waste pipe waste coupling etc of overall size 495x420 mm bowl size 410x330x160mm complete all as specified and directed.

S & F for in repair stainless steel plate rack made out of 1.00mm thick sheet 900x900x200mm complete all as specified and directed.

M & L for mild steel TMT bars, 8 mm dia , cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S & F for 1st class teakwood 35 mm thick plain design as per direction of Engr-in-Charge, framed, panelled shutters (minimum 3 panels) with panel of timber panels are raised and have bevelled or chamefered margins and framing is moulded on solid(for each side) with and incl provn of 10mm thick toughned glass with sand itching of RMS embelem size upto 0.1 sqm in middle rail of door incl PU polishing using high pressure spray gun mirror finish on surface of any description width or girth incluidng cleaning and preparing the surface after applying a coat of wood filler on new works with two or more coats of PU polish complete all as specified and directed.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cms thick in hard / dense soil complete all as specified and directed.

Removing excavated material not exc. 50 m and depositing in soft/hard soil, complete all as specified and directed.

M & L for plain Cement concrete 1:3:6 type C-2 (Using 40mm graded stone aggregates) in foundation, filling and mass concrete complete all as specified and directed.

M & L for reinforced concrete pipes, class NP2, laid and jointed complete with collars concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, for 200mm bore of pipe plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregates) complete all as specified and directed.

S & F for , vitreous China squatting pan of Orrisa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified. Make : Jaquar/Cera/Hindware/Parryware

S & F for vitreous china half stall urinal with grating and union complete set with 40 mm dia GI light grade waste pipe incl. brackets etc complete all as specified and directed.

S & F for waste coupling chromium plated size 32 mm with long thread complete all as specified and directed. (Make: Coronet/Jaquar Essco/Prayag)

S & F for aluminium hat & coat hooks solid body 125 mm to 175 mm fixed with brass screw complete all as specified and directed.

M & L for Cutting existing steel tubing for addition and alteration, screwing the existing steel tubing in position and insertion of required size of GI fittings. (i.e. union, nipple,reducing tee) for branch connection of internal dia 20 mm dia complete all as specified and directed.

M & L for screwing existing steel tubing 20 mm bore for alteration or additions etc complete all as specified and directed.

S & F for stack clamps out of 40mm by 4 mm flat iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100/75mm bore etc complete all as specified and directed.

S & F for rotational molded polyethylene water storage tanks white in colour, tripple layered with threaeded lid/cover, weight of tank should not be less than 36.00 Kg (cylindrical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position all as specified and directed. (Make:- Sintex/ Rotex/ Polycon/Vectus)

S & F for Powder coated aluminium doors / windows / ventilator fixed / openable / sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary jointing cleats, glazing clip,rubber packing, anodised aluminium snap beading, screw, handles etc complete all as specified and directed.

M & L for Formwork to edges of concrete flats and similar works exc. 10 cm & not exc. 20 cm wide with rough finished surfaces etc complete all as specified and directed.

S & F for PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed .

S & F for PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

M & L for formwork to sides and soffits of plinth beam, sides of footings, bass of columns and similar work with rough finished surfaces etc. complete all as specified and directed.

M & L for formwork to sides of columns and similar work with rough finished surfaces etc. complete all as specified and directed.

M & L for formwork to sides and soffits of beam, lintel rough finished surfaces etc. complete all as specified and directed.

M & L for form work to soffits of suspended slabs, such as roof slabs and similar work; not exc. 200 mm thick for flat rough finish surfaces complete all as specified and directed.

M & L for brick work with sub-class `B' bricks built in CM 1:4, straight or curved on plan exceeding 6 M mean radius using old size bricks in half brick thick wall etc. complete all as specified and directed.

S & F for PVC factory made shutter solid, PVC moulded prelam coloured on both side door shutter with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board core 28 to 30 mm thick (stiles), with 2, 4 or 6 raised panel design in framing at site as per specifications & drawings, complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

Disconnecting unserviceable sub main wiring/service connection of any size and including conduit and accessories and removing from site and making good the disturbed surfaces complete all as specified and directed.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc complete all as specified and directed.

S & F for of sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 6.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor complete all as specified and directed.

S & F for of sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 4.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 4 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor complete all as specified and directed.

M & L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type pressed steel modular terminal box and modular white cover plate with frame for suitable module as per site requirements for mounting of modular switches, sockets, fan regulator etc and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth for the following, complete all as specified and directed:-

All as per Item No 204.00 above but One light point/bell point controlled by one way 5 Amps SP switch

All as per Item No 204.00 above but One ceiling fan/exhaust fan/Ventillation fan point controlled by one, one way switch.

All as per Item No 204.00 above but One 5 pin 5 Amps socket outlet on same board with other switch

All as per Item No 204.00 above but One 5 Pin 5 Amps socket outlet on independent board with other switch.

&L for point wiring with 2.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type pressed steel modular terminal box and modular white cover plate with frame for suitable module as per site requirements for mounting of modular switches, sockets, fan regulator etc and one green colour cable of 2.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth for 15 Amp socket outlet on independent board, complete all as specified and directed.

S & F for modular stepped type ceiling fan regulator, 230 volt AC, 2 module, complete all as specified and directed.

S & F for of modular switch 1 way 6/10Amp , 1 module, complete all as specified and directed.

S & F for of modular switch 1 way 16Amp, 1 module, complete all as specified and directed.

S & F for of modular bell push, 6 Amp, 1 module, complete all as specified and directed.

S & F for of modular socket 6Amp, 2/3 pin combined 2 module complete all as specified and directed.

S & F for of modular socket 6Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S & F for switch piano flush type 5 amps, single pole one way 240 volts complete all as specified and directed.

S & F for ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified and directed.

S & F for of door bell ding dong type electric 230 volts AC , single phase, complete all as specified and directed.

S & F for of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

S & F for LED lamp 9/10 watt , 230 volts , 50 Hz, B-22 base for fixing in lamp holder and wall mounted decorative light fitting complete all as specified and directed.

S & F for in repair LED tube light fitting in acrylic linear tube (1x 18 watt),230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed.

S & F for LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F for LED lights fitting 1x 16W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F for testing and commissioning energy saving street light luminaire 35 watt LED , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete with individual LED lences and complete all as specified and directed.

S & F in repair single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB SP `C' type instantaneous for geyser & AC complete all as specified and directed.

Taking down existing fan, exhaust fan re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed.

Taking down existing geyser and refixing after cleaning and descaling complete all as specified and directed.

S & F for of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 08 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed.

S & F for of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 4 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed.

S & F for of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'B' curve complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 Amp to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SP, 240 volt, 63 Amp capacity, 10 KA, 'B' curve complete all as specified and directed.

S & F of MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'B' curve complete all as specified and directed.

S & F for of MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'B' curve complete all as specified and directed.

S & F for exhaust Fans AC single phase 230/240 volts of size 300 mm sweep steel body with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed.

S & F for ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy including fan hook complete with all as specified and directed.

M & L for earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire all as shown in Plate No. 2 to the earthing test point all as specified and indicated including testing on completion complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing complete all as specified and directed.

M & L for TV Socket incl PVC conduit and co axial cable wire complete all as specified and directed.

M & L for Telephone socket incl PVC conduit and telephone wire complete all as specified and directed.

Supply and spread sand in trenches as sand cushioning to underground cable for protection with dry fine river sand and provide required cover after punning down 18CM will be measured and paid complete all as specified and directed. (Note: Thickness of sand cushion after punning down will be measured and paid.)

Taking out old unserviceable Lt Panel of any size and capacity,Supply, install, testing and commissioning of Bus bar chamber of size 60 cm x 60cm x 40 cm outdoor type suitable for LT 415 volts 3 phase 4 wire system factory made cubical complete materialised dust and vermin proof (protection class IP 54), made out of 3.15mm thick MS sheet (CRCA) including factory made hinged type door both side opening with locking arrangement duly painted with two coats of synthetic enamel paint with powder coated finish over a coat of zinc chrome primer complete all as specified and directed. the panel board shall be comprising of the following accessories.

Supply and laying well burnt sub class ‘B’ bricks ( designated 75) locally available best quality, laid dry in trenches for protection of underground cable all as specified and directed.

Taking up/down worn out/damaged/unserviceable xlpe /PVC insulated underground cable rmoured, heavy duty with aluminium conductors of any size, 1100 Volt grade from trench/duct/pole/wall/ pipes/rooftops etc. complete all as specified and directed.

Supply, laying, Jointing connecting in replacement of LT UG cable XLPE insulated,PVC bedded galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 16 sqmm 2 core laid in trenches / on poles / walls / in ducts / passing through pipes and including necessary cable lugs, bolts, nuts and washers complete all as specified and directed.

S & F for of 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheating of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than one meter apart including 4 mm suspension wire one twin core cable 2 core flat of 10 sqmm size complete all as specified and directed.

S & F for tubes light grade GI tubing 40 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection complete all as specified and directed.

S & F for in replacement GI Tubes 20 mm dia medium grade with all fittings and fixed complete to walls/floors/trenches complete all as specified and directed. Make: TATA/JINDAL/SWASTIK

S & F for street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

S & F for water heater storage type,electric, capacity 25 litres, BEE 5 star rated, 240 volts, input 2000 KW, PUF insulated fitted with stainless inner container and cooper coil of BEE 5 star rating models, max working head of water 25 Ltrs, fixed to wall with suitable MS tower/anchor bolts,Inlet/outlet pipes incl PVC connections grouted to wall complete all as specified and directed. Make: Havells/Bajaj/Crompton

S & F for GI Tubes 20 mm dia medium grade with all fittings and fixed complete to walls/floors/trenches complete all as specified and directed. Make: TATA/JINDAL/SWASTIK

TANISHQ ENTERPRISES (BID ID -3263418)

VIPRABANDHU CONSTRUCTIONS (BID ID -3268550)

M/s Kishan Gopal Agarwal (BID ID -3263565)