Renovation of Natraj andShambu boys Hostel at Dr YSP University of Horticulture and Forestry Nauni Solan.

Amount

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length etc. complete in all respect as per satisfaction of Engineer-in-Charge. ( hold fast lugs or dash fastener shall be paid for separately. a).Sal wood

Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick: a) 4 mm thick glass pane (weight not less than 10 kg per sqm).

Providing and fixing Kiln seasoned and chemically treated hollock wood 30 mm thick. Glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing wire gauge shutters Kiln seasoned and chemically treated hollock wood using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws with 35 mm (Thirty five milimetre) thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size etc. complete in all respect as per satisfaction of Engineer-in-charge..

Providing and fixing 2nd class teak wood 40mm into 12 mm wooden Chamfered moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 2nd class teak wood 20mm into 20 mm wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing fly proof galvanized MS wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm etc. complete in all respect as per satisfaction of Engineer-in-charge a). Second class teak wood beading 20mm into 20 mm

Providing and fixing 100x58x1.90 mm ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing ISI marked oxidized/ Chromium plated M.S. Sliding door bolts with nuts and screws etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 250x16 mm ( Two hundred fifty into sixteen milimetre)

Providing and fixing ISI marked oxidized// Chromium plated M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 200x10 mm( Two hundred into ten milimetre)

b). 150x10 mm( One hundred fifty into ten milimetre)

Providing and fixing ISI marked oxidized/ chromium plated M.S. handles conforming to IS:4992 with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 125mm (one hundred twenty five milimetre)

b). 100mm (one hundred milimetre)

Providing and fixing ISI marked 85x42 mm oxidized M.S. pull bolt lock conforming to IS: 7534 with necessary screws bolts, nut and washers etc. complete. in all respect as per satisfaction of Engineer-in-Charge

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-charge. a) Single rubber stopper.

Providing and fixing aluminum U beading of required size to Pre-laminated/ flush door shutter, including fixing etc. complete as per direction of Engineer-in-charge.

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws andapplying a priming coat of approved steel primer, all complete as per the directionof Engineer-In-charge.

Providing and fixing jointless Ist quality ceramic glazed wall tiles (Kazaria / Oreint bell / Nitco/ Somany make) conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete in all respact as per direction of Engineer-in- Charge..

40 mm (forty milimetre) thick Cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm (twenty milimetre)nominal size finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge.(TATA/ JINDAL MAKE)

Providing and fixing precoated galvanised steel sheet Ridges plain (500 - 600mm) 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete in all respect as per satisfaction of Engineer-in-Charge

15 mm (fifteen milimetre thick) cement plaster on rough side of single or half brick wall of mix with cement mortar 1:6 (one cement: six sand) complete in all respect as per satisfaction of Engineer-in-Charge.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Two or more coats on new work.

Providing and applying white cement based putty of average thickness one mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete etc. in all respect as per satisfaction of Engineer-in-Charge

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer’s specification etc. complete in all respect as per satisfaction of Engineer-in-Charge.. a). one or more coats on Old work.

Painting with synthetic enamel paint of approved brand and manufacture of required color to give an even shade etc. in all respect as per satisfaction of Engineer-in-Charge..a) One or more coats on old work

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 Sqm and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge a).With cement mortar 1:4 (one cement : four sand)

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge ( upto 2 Sqm area or below ).

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within all leads of etc. complete in all respect as per satisfaction of Engineer-in-charge. a) G.S. Sheet

Taking out doors, windows and clerestory window shutters (wood or steel) including stacking in all leads etc. in all respect as per satisfaction of Engineer-in-Charge a) Of area 3 square metre and below

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing 32mm dia Semi rigid pipe P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete in all respect as per satisfaction of Engineer-in-Charge..

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

a). 20 mm (twenty milimetre) nominal bore

b). 25 mm (twenty five milimetre) nominal bore

Providing and fixing 45 cm length and 15 mm nominal dia u-plasticized PVC connection pipe with brass unions complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 complete in all respect as per satisfaction of Engineer-in-Charge (Spartan/ Seiko/ smile/ Czar make).

Cutting holes up to 30x30 cm in walls including making good the same with common burnt clay F.P.S. (non modular) bricks complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing 100mm dia chromium plated grating of superior quality for floor, gully or nahani trap complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 25 mm (Twenty five milimetre) thick factory made shutters of Pre-laminated HDHMR (High Density High Moisture Resistancee) board both side decorative finish conforming to IS: 12406 Grade of approved design, including fixing of heavy MS hinges 4” long etc. complete as per architectural drawing and direction of Engineer-in-Charge. (Cost of hinges will be paid for separately).

Suman Verma (BID ID -542147)