SPL REPAIRS TO PARKING SHED PROVN OF DI WATER PIPE LINE NEAR VIKASPATH INCLUDING CERTAIN MINOR WORKS AT VRDE AHMEDNAGAR

Amount

PART - I B/R PORTION (PARKING SHED) Demolition of cement concrete in above ground floors not exc. 15 cm thickness (below or above ground level)

M & L 75mm thick PCC 1:2:4 type B-2 thick using 40mm graded stone aggregate as flooring without using extra cement

Taking down the cement plaster from brick or concrete wall etc. And raking out joints, hacking for key and scrubbing down with water etc. complete.

Material & Labour for Rendering 10mm thick for ceiling surface of wall in CM 1:6 finished even and smooth with thin layer of neeru finish

Material & Labour for preparing New decorated surfaces of in ceiling and applying three coat of white wash all as specified and directed by Engr in Charge

M&Lfor rendering 15mm thick in cm 1:4 finished with fair finish as specified on fair faces of brick work or concrete surfaces

Material & labour for cement base paint two coats over a coat of primer over prepared plaster surface.

Material & Labour for preparing old decorated surfaces of walls and applying one coat of of cement base paint etc complete.

M&L for 50 mm thick Padding cement concrete 1:2:4 type B1 using 20mm thick aggregate with a mixture of water proofing liquid by weight of cement on dried concrete surface finished fair and even without using extra cement .Note :- Water Proofing liquid shall be measured seperately

M&L Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. with brushing neat cement slurry with 3.0 Kg of cement per sqm

M&L for 15mm thick cement plaster in CM (1 : 3) with a mixture of water proofing liquidb by weight of cement on driedconcrete surface finished fair and even without using extra cement .Note :- Water Proofing liquid shall be measured seperately

Supply only Water Proofing liquid

(a) The roof surface shall be throughly wire brushed washed, dried up and cleaned of all forgein matter and dust to receive primer (b) On the dried oof surafce one coat of approved bitumens primer @ 0.25 to 0.30 ltrs per Sqm shall be applied (c) On this primed surface the polymerized modified bituminus water proofing memberance with non woven polyster as reinfocement memberance with white gravel /mineral finished on upper side having weight @ 3.5Kg/Sqm & thickness 2.5 to 3mm shall be laid by torch application method. The overlap while torching shall be 100mm on length side & 100mm on width side of memberance as per manufacture instructions

M&L for preparation of old surfaces of steel of any description over 10cm width or girth,and applying two coats of synthetic enamel paint over one coat of red oxide,zinc chrome primer,complete all as specified and directed by Engr-In-Charge.

PART - II B/R PORTION MW NO. 05 Excavation in post holes (or similar holes) each not exceeding 0.5 Cum getting out, returning filling in & removing earth/broken rubble mixed with earth around in layers not exceeding 25 cm, watering & removing surplus soil to a distance not exceeding 50 mtr and making good to surface in soft/loose soil.

M & L PCC 1:3:6 Type C1 using 20 mm graded stone aggregate as in foundation filling and mass concrete

S & F joist, channel, angle or tee sections fixed independently, without connecting plates, without connecting plates etc,. confirming to Fe-290-Gde-E-250.

S & F mild steel screw bolts (machine made) with hexogonal or square heads at one end and screwed the other, or screwed both ends, each screwed ends to be fitted with washers and one hexogonal or square nut exceeding 5 cm and not exceeding 10 cm long and 11 to 15 mm diameter of neck all as specified.

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M & L preparation of newly prepared steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

PART - III B/R PORTION MN NO. 06 Excavation in post holes (or similar holes) each not exceeding 0.5 Cum getting out, returning filling in & removing earth/broken rubble mixed with earth around in layers not exceeding 25 cm, watering & removing surplus soil to a distance not exceeding 50 mtr and making good to surface in soft/loose soil.

M & L PCC 1:3:6 Type C1 using 20 mm graded stone aggregate as in foundation filling and mass concrete

S & F joist, channel, angle or tee sections fixed independently, without connecting plates, without connecting plates etc,. confirming to Fe-290-Gde-E-250.

S & F mild steel screw bolts (machine made) with hexogonal or square heads at one end and screwed the other, or screwed both ends, each screwed ends to be fitted with washers and one hexogonal or square nut exceeding 5 cm and not exceeding 10 cm long and 11 to 15 mm diameter of neck all as specified.

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M & L preparation of newly prepared steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

PART - IV B/R PORTION MN NO. 07 S & F collapsible steel gates, top hung consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified errected in position and securing runners with hold fasts and brackets complete all as specified and directed.

M & L preparation of newly prepared steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

PART - V B/R PORTION MN NO. 08 S & F powder coated anodised aluminium frames for doors, windows, ventilators with one or more rebates, including jointing cleats for fixing etc complete all as specified and directed

S & F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 Kg/mtr including necessary jointing cleats, glazing clips, rubber neoprene packing, handles - 02 Nos in each door, hinges, anodised aluminium snab beadings, screws etc., complete all as specified and directed.

S & F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and 250 mm length of bolt and fixed

S&F Aluminium 4 Levers, Mortice lock, vertical type, size 75 mm

S & F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed

S & F 18/19 mm thick prelaminated particle board, exterior grade prelaminated both sides with decorative choice laminations and fixed to any type of frame work with screws.

S & F sheet glass ordinary quality 6.30 mm thick, any size, tinted of approved colour fixed with and including rubber beading.

PART - VI B/R PORTION MN NO. 09 S & F powder coated anodised aluminium frames for doors, windows, ventilators with one or more rebates, including jointing cleats for fixing etc complete all as specified and directed

S & F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 Kg/mtr including necessary jointing cleats, glazing clips, rubber neoprene packing, handles - 02 Nos in each door, hinges, anodised aluminium snab beadings, screws etc., complete all as specified and directed.

S & F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and 250 mm length of bolt and fixed

S&F Aluminium 4 Levers, Mortice lock, vertical type, size 75 mm

S & F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed

S & F sheet glass ordinary quality 6.30 mm thick, any size, tinted of approved colour fixed with and including rubber beading.

S & F aluminium extruded section body door closer hydraulically regulated, design No.3, universal type suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kgs and fixed

PART - VII B/R PORTION MN NO. 10 Excavation in trenches not exceeding 1.5 mtr width and not exceeding 1.5 mtr in depth for foundation etc or for shafts, wells, cess pits, manholes, pier holes, etc not exceeding 10 sqm on plan and not exceeding 1.5 mtr in depth and getting out in hard/dense soil.

M & L PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation filling and mass concrete

M & L brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radious, built in CM 1:6

M & L providing cement concrete type B0,1:2:4 type using 12.5 mm graded stone aggregate as in copings etc including necessary form work., all as specified and directed.

M & L rendering cement plaster 15 mm thick in CM 1:4 on fair faces of brick or concrete surfaces finished even and smooth without extra cement

M & L for preparation of newly prepared plastered surfaces of walls and applying two coats of cement based paint over a coat of primer all as specified and directed

Returning filling in including spreading, levelling in layers not exceeding 25 cm thick and well ramming including watering as required

Removing excavated soils not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point.

PART - VIII B/R PORTION MN NO. 11 Taking down cement or cement lime plaster on brick or stone walls etc, including raking out joints, hacking for key, scrubbing with water etc of any description.

Roughening surfaces of old concrete by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0 kgs of cement per sqm

M & L brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radious, built in CM 1:6

M & L providing cement concrete type B0,1:2:4 type using 12.5 mm graded stone aggregate as in copings etc including necessary form work., all as specified and directed.

M & L rendering cement plaster 15 mm thick in CM 1:4 on fair faces of brick or concrete surfaces finished even and smooth without extra cement

M & L for preparation of newly prepared plastered surfaces of walls and applying two coats of cement based paint over a coat of primer all as specified and directed

PART - IX B/R PORTION MN NO. 12 S & F motorised steel rolling shutters with ball bearings as specified, including top cover, anchoring rod, hasp & staple and one shop coat of primer errected in position as indicated complete gear operated with chain wheel and hand chain. Thickness of laths 1.25 mm thick with gear box including necessary items for motorised rolling shutters. (Motor having sufficient strength to lift rolling shutter).

M & L preparation of newly prepared steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

PART - X B/R PORTION MN NO. 13 Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out soft/loose soil and compacted

M & L 100mm thick Cement Concrete type D2, 1:4:8 using 40 mm graded stone aggregate as in floors.

M & L 150 mm thick Cement Concrete type B1, 1:2:4 using 20 mm graded stone aggregate as in hard standing finished even and smooth using extra cement and finished wit Spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green.

M & L contineous brick edging with burnt clay bricks of old size with width equal to the depth of the brick laid dry on edge

Removing excavated soils not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point.

PART - XI B/R PORTION MN NO. 14 Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out soft/loose soil and compacted.

M & L 100mm thick Cement Concrete type D2, 1:4:8 using 40 mm graded stone aggregate as in floors.

M & L 150 mm thick Cement Concrete type B1, 1:2:4 using 20 mm graded stone aggregate as in Ramp / hard standing finished even and smooth using extra cement and finished wit Spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green.

M & L brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radious, built in CM 1:6

M & L providing cement concrete type B0,1:2:4 type using 12.5 mm graded stone aggregate as in copings etc including necessary form work., all as specified and directed.

M & L rendering cement plaster 15 mm thick in CM 1:4 on fair faces of brick or concrete surfaces finished even and smooth without using extra cement

M & L contineous brick with burnt clay bricks of old size with width equal to the depth of the brick laid dry on edge

Removing excavated soils not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point.

PART - XII B/R PORTION MN NO. 15 Taking down cement or cement lime plaster on brick or stone walls etc, including raking out joints, hacking for key, scrubbing with water etc of any description.

Roughening surfaces of old concrete by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0 kgs of cement per sqm

M & L brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radious, built in CM 1:6

M & L providing cement concrete type B0,1:2:4 type using 12.5 mm graded stone aggregate as in copings etc including necessary form work., all as specified and directed.

M & L rendering cement plaster 15 mm thick in CM 1:4 on fair faces of brick or concrete surfaces finished even and smooth without extra cement

M & L for preparation of newly prepared plastered surfaces of walls and applying two coats of cement based paint over a coat of primer all as specified and directed

M&L PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) 25mm thick as in floor finished fair and even for laying of leveled bed.

S&F Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 15 mm thick screed bed or bedding layers in CM 1:6.

S&F Coloured Glazed ceramic tiles 300 x 200 x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 10 mm thick rendring layers in CM 1:4.

S&F Soild PVC Door frame of size 50 mm x 47 mm made out of 5 mm palin colour PVC sheet reinforced with MS square tube, suppling and fixing in opening as per specification and drawing

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall bw covered with heat moulded plain colour PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and botom rail on either side & as gap insert for tip rail & bottom rails; Panelling of plain colour PVC sheet to be fitted in the MS frame weloded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement. suppling and fixing in the frame at site as per specification & drawing

S & F steel windows or ventilators fixed type with glazing bars

S & F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section

S & F 100 mm long extruded Aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin type C 21.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised.

M&L Precast cement concrete 1:3:6, type C1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4

M&L Mild steel TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips.

S & F MS steel work in tubular trusses including special shaped washers etc., complete using but ERW or induction butt welded tubes confirming to IS 1161- 1979 graded St 240 with one shop coat of zinc chromate primer paint.

S & F Mild steel , flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, wind ties, clamps and similar small articles etc

Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.

S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors.

S & F Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union

S & F Brass Chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges.

S & F Soap dish, vitreous China white of approximate size 160 x 160 x 90 mm.

S&F rotational moulded polyethylene water storage tanks (cylinderical, vertical with closed top) of 500 Ltrs capacity hoisted and fixed in position inc 20mm bore PVC float valveall as specified and directedin SSR Pt I

S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors.

S & F 15 mm bore Bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

S & F 20 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S & F 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F PVC connections 15mm bore size with PTMT nuts of length 450mm.

S & F Vitreous China Squatting pan of pattern long pan, size 580 mm white with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including concrete complete including making good to floor.

S&F PVC flushing cistern, low level white with inlet ball valve float and handle including flushing pipe & bracket complete 10 ltrs capacity.

S&F grating round 100 mm size of PTMT (min weight 25 grms)

S & F Vitreous china urinal, bowl type flat back of size 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws,

M & L concrete bed to drain pipes in cement concrete 1:3:6 type C2 including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 100 mm dia bore all as specified and directed.

M & L for 100 mm internal dia of bore salt glazed stoneware pipes laid in trenches and jointed as specified.

Cutting into existing manholes for connecting new drains of 100 mm dia bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required.

S & F Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size (flat back or angle back type) including 15 mm dia CP pillar tap - 01 No and cutting for and pinning ends of brackets or erecting stand.

PART - XIII B/R PORTION MN NO. 16 Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out soft/loose soil

M & L 100mm thick Cement Concrete type D2, 1:4:8 using 40 mm graded stone aggregate as in floors.

M & L 150 mm thick Cement Concrete type B1, 1:2:4 using 20 mm graded stone aggregate as in floors finished even and smooth using extra cement.

M & L contineous brick edging with burnt clay bricks of old size with width equal to the depth of the brick laid dry on edge

Removing excavated soils not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point.

S & F HDPE green wheeled dust bins of size 1175 mm x 1310 mm x 775 mm as per manufacturer instruction

PART - XIV B/R PORTION MN NO. 19 S&F Soild PVC Door frame of size 50 mm x 47 mm made out of 5 mm palin colour PVC sheet reinforced with MS square tube, suppling and fixing in opening as per specification and drawing

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall bw covered with heat moulded plain colour PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and botom rail on either side & as gap insert for tip rail & bottom rails; Panelling of plain colour PVC sheet to be fitted in the MS frame weloded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement. suppling and fixing in the frame at site as per specification & drawing

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section

S & F 100 mm long extruded Aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin type C 21.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised.

PART - XV B/R PORTION MN NO. 20 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc., and brushing neat cement slurry with 3.00 Kg of cement per Sqm

Taking down cement plaster on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc,.

M & L for vertified coloured tiles of size 600 x 600 x 10 mm thick in floors set and jointed in neat cement slurry and pointed with adhesive material to match to tiles as in floors over 15 mm thick screed bed or bedding layer for laying of floor finishes in CM 1:6.

M & L for vertified coloured tiles of size 600 x 100 x 10 mm thick in vertical surfaces/skirting on wall set and jointed in neat cement slurry and pointed with adhesive material to match to tiles over and including rendering 10 mm thick in CM 1:4.

PART - XVI B/R PORTION MN NO. 21 Excavation in post holes (or similar holes) each not exceeding 0.5 Cum getting out, returning filling in & removing earth/broken rubble mixed with earth around in layers not exceeding 25 cm, watering & removing surplus soil to a distance not exceeding 50 mtr and making good to surface in soft/loose soil.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out soft/loose soil

M & L PCC 1:3:6 Type C2 using 40 mm graded stone aggregate as in foundation filling and mass concrete

M & L PCC 1:2:4 Type B1 using 20 mm graded stone aggregate 100 mm thick as in pavings/hard standing.

Supply Convex security mirrors are suitable for outdoor and indoor use on the road for safety, unbreakable pole mounted bracket 1000 mm dia viewing distance min 10 mtrs from convex mirror, fish eye mirror all as specified and fixing with providing cement concrete type B1,1:2:4 in post as directed.

PART - XVII B/R PORTION MN NO. 22 M & L rendering cement plaster 15 mm thick in CM 1:4 on fair faces of brick or concrete surfaces finished even and smooth without extra cement

M & L preparation of newly prepared brick/stone/concrete surfaces over 10 cm width or girth and applying two coats of plastic emulsion paint over a coat of priming paints plaster coat primer all as specified and directed.

Writing letters or figures (Block, Roman, Italic or Indian) height of letters 15 cm (Note :- Letters should in three languages English, Hindi and Marathi).

PART - XVIII B/R PORTION MN NO. 23 Demolition of brickwork or stone/boulder masonry built in cement mortor including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles.

M & L PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in hold fasts set in CM 1:4.

S & F framed work as in doors or gates of angle or other section with guesset plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and and including eigther hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete confirming to Fe-290 Gde-E-165.

M & L preparation of newly prepared steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

PART - XIX B/R PORTION MN NO. 24 S & F powder coated anodised aluminium frames for doors, windows, ventilators with one or more rebates, including jointing cleats for fixing etc complete all as specified and directed

S & F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 Kg/mtr including necessary jointing cleats, glazing clips, rubber neoprene packing, handles - 02 Nos in each door, hinges, anodised aluminium snab beadings, screws etc., complete all as specified and directed.

S & F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and 250 mm length of bolt and fixed

S & F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed

S&F Aluminium 4 Levers, Mortice lock, vertical type, size 75 mm

S & F powder coated anodised aluminium windows and ventilator shutter, side hung type without sash bars aluminium section weighing 0.55 Kg/mtr including necessary jointing cleats, glazing clips, rubber neoprene packing, peg stays - 01 No, aluminium handles 1100 mm - 01 Nos, aluminium butt hinges type B-21 100 mm - 02 Nos, anodised aluminium snab beadings, screws etc., complete all as specified and directed.

S & F sheet glass ordinary quality 6.30 mm thick, any size, tinted of approved colour fixed with and including rubber beading.

S & F sheet glass ordinary quality 4.00 mm thick, any size, tinted of approved colour fixed with and including rubber beading.

PART - XX B/R PORTION MN NO. 25 S & F powder coated anodised aluminium frames for doors, windows, ventilators with one or more rebates, including jointing cleats for fixing etc complete all as specified and directed

S & F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 Kg/mtr including necessary jointing cleats, glazing clips, rubber neoprene packing, handles - 02 Nos in each door, hinges, anodised aluminium snab beadings, screws etc., complete all as specified and directed.

S & F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and 250 mm length of bolt and fixed

S & F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed

S&F Aluminium 4 Levers, Mortice lock, vertical type, size 75 mm

S & F 18/19 mm thick prelaminated particle board, exterior grade prelaminated both sides with decorative choice laminations and fixed to any type of frame work with screws.

S & F sheet glass ordinary quality 6.30 mm thick, any size, tinted of approved colour fixed with and including rubber beading.

PART - XXI B/R PORTION MN NO. 26 Excavation in post holes (or similar holes) each not exceeding 0.5 Cum getting out, returning filling in & removing earth/broken rubble mixed with earth around in layers not exceeding 25 cm, watering & removing surplus soil to a distance not exceeding 50 mtr and making good to surface in soft/loose soil.

M & L PCC 1:3:6 Type C1 using 20 mm graded stone aggregate as in foundation filling and mass concrete

S & F joist, channel, angle or tee sections fixed independently, without connecting plates, without connecting plates etc,. confirming to Fe-290-Gde-E-250.

S & F mild steel screw bolts (machine made) with hexogonal or square heads at one end and screwed the other, or screwed both ends, each screwed ends to be fitted with washers and one hexogonal or square nut exceeding 5 cm and not exceeding 10 cm long and 11 to 15 mm diameter of neck all as specified.

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in cladding to wall, fixed with self tapping screws as specified

M & L preparation of newly prepared steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

PART - XXII B/R PORTION MN NO. 27 S & F powder coated anodised aluminium frames for doors, windows, ventilators with one or more rebates, including jointing cleats for fixing etc complete all as specified and directed

S & F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 Kg/mtr including necessary jointing cleats, glazing clips, rubber neoprene packing, handles - 02 Nos in each door, hinges, anodised aluminium snab beadings, screws etc., complete all as specified and directed.

S & F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and 250 mm length of bolt and fixed

S & F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed

S&F Aluminium 4 Levers, Mortice lock, vertical type, size 75 mm

S & F powder coated anodised aluminium windows and ventilator shutter, side hung type without sash bars aluminium section weighing 0.55 Kg/mtr including necessary jointing cleats, glazing clips, rubber neoprene packing, peg stays - 01 No, aluminium handles 1100 mm - 01 Nos, aluminium butt hinges type B-21 100 mm - 02 Nos, anodised aluminium snab beadings, screws etc., complete all as specified and directed.

S & F sheet glass ordinary quality 6.30 mm thick, any size, tinted of approved colour fixed with and including rubber beading.

S & F sheet glass ordinary quality 4.00 mm thick, any size, tinted of approved colour fixed with and including rubber beading.

PART - XXIII B/R PORTION MN NO. 28 S & F 2.00 mm thick PVC tiles/sheets laminated plain coloured, marbled mosaic or mottled finished laid with approved rubber based adhesive in floors including roughening and cleaning of existing floor.

PART - XXIV B/R PORTION MN NO. 29 S & F framed work such as grills, gratings etc., with ends of bars shouldered and/or rivetted or forged in to spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work confirming to Fe-290-Gde-E-165.

S & F Aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of apparture 1.40 mm and fixed with aluminium wire staples

M & L preparation of newly prepared steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

S & F mild steel screw bolts (machine made) with hexogonal or square heads at one end and screwed the other, or screwed both ends, each screwed ends to be fitted with washers and one hexogonal or square nut exceeding 5 cm and not exceeding 10 cm long and 11 to 15 mm diameter of neck all as specified.

PART - XXV B/R PORTION MN NO. 30 Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out soft/loose soil

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc., or for shafts, wells, cesspits, manholes, pierholes, etc., not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil.

Excavation over areas not exceeding 1.5 m deep and getting in soft/loose soil.

Excavation over areas not exceeding 1.5 m deep and getting in hard/dense soil.

Excavation over areas exceeding 1.5 m deep but not exceeding 3.0 m and getting in soft/disintegrated rock soil.

M & L PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation filling and mass concrete

M & L PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in benching/moulding etc., all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc

M & L brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radious, built in CM 1:6

M & L rendering cement plaster 15 mm thick in CM 1:4 on fair faces of brick or concrete surfaces finished even and smooth without extra cement

M & L mild steel deformed and TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90 mm dia or securing with clips.

M & L precast reinforcement cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate set in cement mortor 1:4 in landings, cover slabs (Manholes etc), chullah hoods, chajjas, water throughs, mengers, shelves and similar articles with plain faces including necessary form work

M & L concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate of 150 mm bore of pipe

M & L 150 mm dia salt glazed stoneware drain laid in trenches and jointed as specified

Returning filling in including spreading, levelling in layers not exceeding 25 cm thick and well ramming including watering as required

Removing excavated soils not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point.

S & F framed work such as grills, gratings etc., with ends of bars shouldered and/or rivetted or forged in to spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work confirming to Fe-290-Gde-E-165.

M & L preparation of newly prepared steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) to cement concrete 1:2:4 type B1 smooth finished and reforming benching as required of 150 mm dia of pipe.

PART - XXVI B/R PORTION MN NO. 31 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc., and brushing neat cement slurry with 3.00 Kg of cement per Sqm

Taking down cement plaster on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc,.

M & L for vertified coloured tiles of size 600 x 600 x 10 mm thick in floors set and jointed in neat cement slurry and pointed with adhesive material to match to tiles as in floors over 15 mm thick screed bed or bedding layer for laying of floor finishes in CM 1:6.

M & L for vertified coloured tiles of size 600 x 100 x 10 mm thick in floors set and jointed in neat cement slurry and pointed with adhesive material to match to tiles as in vertical surfaces/skirting on wall over and including rendering 10 mm thick in CM 1:4.

PART - XXVII B/R PORTION MN NO. 32 M & L brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in CM (1:4)

M & L rendering cement plaster 10 mm thick in CM 1:6 on fair faces of brick or concrete surfaces finished even and smooth without extra cement

M & L preparation of newly prepared plastered surfaces and applying two coats of oil bound distemper over a coat or primer

Cutting holes into or through cement concrete slabs, chajjas etc., reinforced or otherwise superficial area not exceeding 100 sqcm

Cutting out concrete blocks, slabs, brick work or stone masonry (in alternate course) forming toothings for and bonding new work in mortor in to old work, including new materials entering old wall type B1 (1:2:4) using 20 mm graded stone aggregate set in CM 1:4.

M & L form work to sides of soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc., also splays between follrs & beams etc of rough finished surfaces of concrete flat.

M & L mild steel TMT bars 10 mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips

M & L mild steel TMT bars 5 mm dia and over and including 10 mm dia as in stirrups cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips

M & L RCC type B1 (1:2:4) using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels etc., over 1.5 m span

PART - XXVIII E/M PORTION (DI WATER PIPE) Excavation in trenches, not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for laying DI tubing and getting out trimming the sides, forming bottom surface to required level in soft/loose soil complete all as specified and as directed.

Returning, filling in , including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick after laying and testing of cable complete all as specified and as directed.

Removing excavated material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

M & L for ductile iron pipe class K9, 200 mm dia with spigot and socket ends class K9 centrifugally cast in any lenth laid in trenches including push on joints material complete all as specified and as directed.

M&L for CI specials such as bends (any radious, type, angle) tapers any type ,straight bend, increasing decreasing or double socket etc tee pieces any type, single branch, 'y' junctions, double branch, cross all sockets or socket and spigot/ flanged, collers and plugs etc suitable for CI pipes class LA of size upto 200 mm bore dia complete all as directed.

Supply and fix automatic air release valve (dual action float operated) 50 mm dia suitable for 200 mm DI water pipe line with 50mm gun metal stop valve complete all as specified and as directed by Engr-in-charge.

Cutting of CI/DI pipe 200 mm dia for laying of proposed pipe line all as specified and as directed by Engr-in-charge.

M&L for run lead joint of 200 mm dia CI/DI pipe complete all as specified and as directed.

S&F of mechanical joint 200 mm dia made out of MS sheet fabricated as per existing site requirement including long nuts, bolts, rubber gaskets complete all as specified and directed.

PART - XXIX E/M PORTION MW NO. 02 Supply and fixing of LED search light 15 watt (cool white), water resistant and ABS body material with minimum 6000mAh lithium battery (range 1 Km) rechargeable, hand hold, swivel stand torch including charger with cable and holding strip complete all as specified and directed by Engr-in-charge. Make : FOS or equivalent of DIGITALS /Wipro.

PART - XXIX E/M PORTION MW NO. 03 Supply and fix Air cooler electric driven (single phase) PVC/Plastic body, having nominal air flow capacity of 5000 CuM per hour (or nearest size) with wheel. Make - Symphony Model- Siesta 70 or equivalent of Usha/Bajaj.

PART - XXX E/M PORTION MW NO. 04 Supply and fix Air cooler electric driven (single phase) PVC/Plastic body, having nominal air flow capacity of 5000 CuM per hour (or nearest size) with wheel. Make - Symphony Model- Siesta 70 or equivalent of Usha/Bajaj.

PART - XXXI E/M PORTION MW NO. 17 Supply and fixing Refrigerator, direct cool single door 4 star with base drawer, electric driven, (single phase), capacity 190 liters. Complete. Make - LG or equivalent of SAMSUNG/Whirlpool.

PART - XXXII E/M PORTION MW NO. 18 Supply and fixing water heater storage type, electric, capacity 25 Ltr, BEE 5 Star including with PVC pipes and fastners all as specified and as directed by Engr-in-charge .Make - Havells or equivalent of Racold / Bajaj / Crompton.

PART - XXXIII E/M PORTION MW NO. 33 Supply and fixing Exhaust fan complete with louver shutter, 300 mm sweep size of dia, 900 RPM heavy duty suitable for operaiton 230 volts, single phase AC supply with necessary bolts (6 inches long 6mm dia) with nuts and washers for fixing the fan in wall including making necessary electric connection from ceiling rose to the fan with flexible cord copper 3 core of size 23/0.0076 including drilling hole of suitable size on wall to fix exhaust fan complete all as specified and directed. Make : Crompton or equivalent of havells/Usha

Material and labour for point wiring with single core PVC insulated and unsheathed 1100 volts garade electric cable with multistranded copper conductor of size 1.5 sqmm (nominal area) drawn through & including PVC casing and caping, medium duty (ISI marked) on wall, ceiling with GI screws, rawl plusgs with all fittings including tees, junction boxes & provision of pressed steel terminal box powder coated of suitable size with 3mm thick plastic laminate sheet cover for mounting switches, sockets & regulators & drawing continuous earth wire of PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 1.5sqmm (nominal area) complete all as specified and directed by Engineer-in-Charge.

Supply and fixing switch piano, flush button 5 Amps single pole, one way complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ceiling rose, surface, backlite 3 terminals 65mm x 50mm complete all as specified and directed by Engineer-in-Charge.

PART - XXXIV E/M PORTION MW NO. 34 Supply and fix water cooler electric driven (single phase), Fully stainless steel body, having approx storage capacity of 120 litre and nominal cooling capacity of 60 Litres per hour. Make - Voltas or equivalent of Blue star/USHA

Supply, installation and testing of Ultra advanced UV water purifier complete with all fittings.Make - Eureka Forbes Model -AG 200L or equivalent of Kent, Pureit

Material and labour for point wiring with single core PVC insulated and unsheathed 1100 volts garade electric cable with multistranded copper conductor of size 2.5 sqmm (nominal area) drawn through & including PVC casing and caping, medium duty (ISI marked) on wall, ceiling with GI screws, rawl plusgs with all fittings including tees, junction boxes & provision of pressed steel terminal box powder coated of suitable size with 3mm thick plastic laminate sheet cover for mounting switches, sockets & regulators & drawing continuous earth wire of PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 2.5sqmm (nominal area) complete all as specified and directed by Engineer-in-Charge.

Supply and fixing socket outlet 2 in 1, 3 pin, 5 and 15 amps flush type complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing switch piano, flush button 15 Amps single pole, one way complete all as specified and directed.

Supply and fix GI pipe "medium grade" size 15 mm with all fittings and fixed complete to walls and ceilings or laid in floor.

Supply and fix stop valves fancy type, Chromium plated, screwed down, high pressure with cruch or butterfly handle, screwed both ends for iron pipes or for unions fixed size 15mm dia.

Smruti Construction

MS. G.A. CONSTRUCTION