GE 874/EWS-05/2021-22

Amount

B/R & E/M Portion

Dismantling plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof covering.

Dismantling of timber scantlings 40 Sq cm and over in section in any position in unframed work.

Dismantling wall/ceiling board of any description including cover fillets.

Dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the permises.

Demolition of concrete (unreinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level).

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles.

Dismantling Unframed works of eaves boarding, any description, fixed in any position with nails.

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or removal to store.

Taking up or down 20mm bore steel tubing and connections including cleaning for refixing or removal to store.

Taking down chowkhats or frame exc. 1.5sqm and n.exc. 4Sqm each with shutter (w/o taking out shutter from the frame).

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each per leaf complete all as specified and directed.

Dismantling water tank exc 500 Litre & n.exc 1000Litre capacity and removing to store.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water, etc.

Hacking out old broken glass exc 1.5 sq m (any thickness, size, quality or description) from wooden frames or stone, concrete or bricks surrounds, glazed with oil putty or fixed with beads complete alll as specified and directed.

6 mm thick plywood, 5 Nos of Ply, grade BWR, type BB fixed with nails to timber frame work in ceiling.

Second class soft wood as in scantling clean sawn fixed in position.

Plain fillets square, rectangular in section exc. 3 & n exc. 6 sqcm. of second class softwood.

Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with tapping screws as specified.

Pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with tapping screws as specified.

Second class soft wood plain, solid straight chowkats and frames, wrought framed rebated on the solid rounded or chamfered, put together with glue pinned and joints.

35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying & fixing in opening, complete all as specified and directed by Engr-in-charge.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification, complete all as specified.

35 mm thick 2nd class soft wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats.

Eaves Boarding of 20mm thick of Softwood 2nd class with nails in any situation (except flooring and skirting) , Planed one side with butt joints complete all as specified and directed.

Rendering 15 mm thick on other than fair face of brick work in cement mortar 1:4, to be finished even and smooth (without using extra cement).

Rendering 15 mm thick in cement mortar 1:6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing, finished even and smooth without using extra cement.

Preparation of New surfaces plastered or unplastered and applying two coats of cement base paint, white or tinted.

Prepatation of New surface plastered or unplastered with chalk whiting and applying two coat of distemper oil emultion.

Preparation of Old surfaces plastered or unplastered and applying one coat of cement base paint, white or tinted.

Prepatation of Old surface plastered or unplastered and applying one coat of distemper oil emultion paint.

Preparation of old painted surfaces of wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth, and applying one coat of synthetic enamel paint.

Preparation of old painted steel surface of any description over 10 cm width or girth and applying one coat synthetic enamel paint.

Non skid ceramic tiles 7 to 8 mm thick (square / rectangular) (coloured tiles) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles, complete all as specified.

Glazed ceramic Coloured tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface.

Screed bed or bedding layer of cement mortar 15 mm thick in cement plaster 1:4 for laying floor finishes.

25 mm thick PCC 1:2:4 type B-0, (using 12.5 mm graded aggregate) as sub base complete all as specified.

75 mm thick PCC 1:3:6 type C-2, (using 40 mm graded aggregate) as sub base complete all as specified.

Galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples, fixed in repairs.

Raking out joints / pointing work built in cement mortar to random rubble or polygonal rubble uncoursed or brought up to course masonry.

Raised pointing to random rubble or polygonal rubble, uncoursed or brought upto courses set in cement mortar 1:4.

Sheet glass of 3mm,ordinary quality and glazing with oil putty in squares n.exc 0.5 Sqm in each pane, complete all as specified.

PCC 1:3:6 type C2 in foundation filling and mass concrete (using 40mm graded crushed stone aggregate).

Walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:4.

PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in coping including necessary formwork, weathering, slightly rounded or chamfered angles as directed.

Rendering 15mm thick in Cement Mortar 1:4 on stone masonry surfaces or surfaces other than fair faces of brickwork and finishing even & smooth without using extra cement.

Extra for forming fair finishing drain or channel 45cm inner girth in cement concrete, using extra cement incl forms, moulds, mitred/stopped ends etc.

Mild Steel TMT Bars of 5 mm dia and over up to 10 mm dia in stirrups, spacers and binders,cut to length bent to shape required including cranking, binding spirally for hooping for columns hooking ends and biniding with and including MS wire annealed not less than 0.9 mm dia or securining with clip all as specified.

Precast cement concrete 1:2:4 type B1 for cover slabs (20mm graded crushed stone aggregate) set in Cement Mortar 1:4 complete all as specified.

Mild Steel butt hinges 100mm long medium weight.

200mm long aluminum alloy, anodized barrel tower bolt of extruded section.

250mm long aluminum alloy anodized sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast of extruded sections and fixing bolts and sliding bolts of extruded section of cast-aluminum alloy.

300mm long aluminum alloy anodized sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast of extruded sections and fixing bolts and sliding bolts of extruded section of cast-aluminum alloy.

Aluminum handles, cast type, anodized 125 mm long.

Hard core of gauge n.exc 63mm depositing, spred and levelled in layers n.exc 15cm thick watering and ramming to true surface with broken stone boulders.

Sand filling under floors or in foundations including watering and consolidation.

Machine pressed precast conctete interlocking paver block With Grey Cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade.

500 Ltr capacity PVC water storage tank (cylinderical vertical with closed top) and fixed in position all as specified in SSR Part -I, including dismantling of old tank.

20 mm fancy type chromium plated stop valves/ gate valve, screwed down high pressure,with crutch or butterfly handle scresed both ends for iron pipe or for unions and fixed in repairs complete all as specified.

20 mm ball brass valves, high pressure,with polythene float and fly completed, scewed for iron pipe or brass ferrule and fixed.

15mm GI steel tubing medium grade with all fittings and fixed complete to walls and ceiling and laid in floors.

20 mm tubes medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors.

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white excluding fixing bolts, flushing cistern and flush pipe including 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level ,white, with inlet ball valve, float and handle including brakets.

PVC flush pipe to WC, including all joints & making good to the floor.

PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe, fixed in repair, complete all as specified.

PVC (SWR) bends any radius 110mm bore fixed in repair, complete all as specified.

PVC (SWR) P trap 110/110mm bore, all as specified.

Vitreous China wash basin, white, flat back of size 550x 400 mm incl cutting for and pining, in ends of brackets or erecting stand etc, fixed in repairs, complete all as specified.

Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms) for 32mm bore dia of discharge pipe to WHB, sink fixed in repairs, complete all as specified.

PVC (SWR) floor trap of diameter of outlet in 75 mm, plain with grating including jointing with solvent cement.

15mm bore bib taps Standard of PTMT any colour high pressure, screwed both ends for iron pipe or for brass ferrule (min weight 15mm-90gms), fixed in repair, complete all as specified.

15mm bore Pillar tap of PTMT any colour high pressure screwed for iron pipes or for union (min weight 15mm-110gms), fixed in repairs, complete all as specified.

Soap dish of PTMT fixed with and including chromium plated brass screws and wooden / plastic plugs, fixed in repairs, all as specified and directed.

Chromium plated shower roses with or without swivel joints,any size, including fixing to steel pipe or union, fixed in repairs.

Angular stop Cock with wall flange suitable for 15mm bore GI pipe. Make : Jaguar (Code CON-053KN).

Corner Glass shelf with bracket fixed in repairs, all as specified and directed by Engr-in-Charge. Make : Jaguar (Code No CAN-1173).

Health faucet CP (ABS Body) with 1 metre long easy Flex Tube in Chrome Finish and Wall Hook, fixed in repairs, all as spd and directed by Engr-in-Charge. Make : Jaguar (Code No ALD-573) or equivalent as approved by GE.

20mm dia D type towel rail 600mm long of brass CP fixed with and including CP brass screws complete.

Curtain Harrison rails, anodised aluminium alloy chromium plated with fixing bracket, stop,rollers etc fixed in repairs.

140 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor.

Steel windows with side hung shutter including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded.

Excavating in trenches, n.exc 1.5m wide and n.exc 1.5m in depth; for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in Hard/dense soil complete all as specified and directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Plain cement concrete type D2 1:4:8 (40mm graded aggregate) as in foundations filling and mass concrete complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality confirming to IS 456:2000 complete all as specified and directed by Engr-in-charge.

Reinforced cement concrete M-25 (20mm graded aggregates) in coloumns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-charge.

Formwork to flat sides of concrete foundations, footings, bases of coloumns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed by Engr-in-charge.

Formwork to sides of pillars, posts, struts, piers, coloumns and stanchions square or rectangular and finished surface with fair finish complete all as specified and directed by Engr-in-charge complete all as specified and directed.

Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement plaster 1: 4 finished surface even and smooth without using extra cement complete all as specified and directed.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering. Doors etc. To be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (including of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engr-in-charge.

Preparation of new steel surface of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-charge.

Preparation of new or previously untreated concrete surfaces of any description,over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed by Engr-in-charge.

Fe 410-W(Gde-E-250) quality -A rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.

Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railing; framework of watertanks and similar work conforming to Fe 290. Gde-E-165 complete all as specified and directed.

25mm neck dia mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, n.exc 15cm long complete all as specified and directed.

Design mix reinforced cement concrete M-25 (20mm graded aggregates) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-charge.

Formwork to curved sides and soffits of arches ( rough finished surface of concrete) and complete the surface with fair finishes complete all as specified and directed.

Roof tiles, Mangalore pattern, interlocking at side joints, laid dry complete all as specified by Engr-in-charge.

Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in lime mortar 1:3 or cement mortar 1:6 complete all as specified and directed.

Providing cement concrete Type B0 1:2:4 (12.5 mm graded aggregate) in roof kerbs (or cantilever beam), mud stops, rounded or chamfered on edges complete all as specified and directed.

3mm thick aluminium composite in ceilling/ Cladding plain of approved colour / shade to beam / column / slab in circular / rectangular shape including all offsets,bending and clits whereever required to give the required shape and shape and design and silicon filling the joints using water proofing sealent including suspension wire wherever required using and fabricating aluminium tubular hollow section 25mmx25mm frame work of size not exceeding 900mm c/c on existing MS pipe purlin / rafter / column to hold ACP cladding etc complete all as specified and directed.

Stainless steel special alloy grade 304 pipes 1.50 mm thick and 100 mm dia as in railing incl required cutting, notching organ welding, riding and drilling counter sunk holes and bending to required shape by mechanical means in factory as per site requirement without forming wrinkles and butting and polishing all as directed by Engr-in-Charge.

Stainless steel lettering of height not exceeding 30 cm & depth 25 mm made of 1 mm thick SS plate including necessary fixing arrangement to walls. Note :- Size & font of letters as given by GE.

20mm thick granite (of any type) tiles machine cut in skirting/dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone incldig grinding and polishing complete all as specified and directed.

Taking out carefully copper / aluminium point wiring, (Light, fan, socket or power) complete with all fitting, fixtures such as switch socket out let, ceiling rose, holder, regulator, DB's etc. including making good the disturbed surface of wall/floors, complete all as specified and as directed.

Point wiring with multi stranded copper conductor of size 1.5Sqmm PVC insulated unsheathed FRLS cable in and including PVC conduit and accessories of suitable size for concealed wiring including 1.50 Sqmm copper earth wire (green colour) FRLS Cable for one light point or fan point or bell point controlled by one No, one way switch using cable of different insulation colour for colour coding including 3mm thick laminated sheet cover, mild steel sunken box and inner and outer plate for mounting including cutting chases and making good to disturbed surfaces of wall / floor, complete all as specified and as directed.

All as per the description of Serial Item No 107 here-in-before but for one 3 pin socket outlet 5 Amp independent, complete all as specified and as directed.

All as per the description of Serial Item No 107 here-in-before but for one 3 pin socket outlet 5 Amp on same board, complete all as specified and as directed.

All as per the description of Serial Item No 107 here-in-before but for one 3 pin socket outlet 15 Amp independent board using cable of size 2.5 Sqmm conduit all as specified and directed.

Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

Electronic fan regulator stepped type one module with five step 240 volts 100 watt suitable for 1200mm / 1400mm sweep AC ceiling fan including taking out the unserviceable, complete all as specified and as directed.

Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings complete all as specified and as directed.

Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified.

Switch piano flush type 16 Amp single pole one way, (ISI marked), complete all as specified.

Switch Socket combination 2 in 1, 5 Amp flush type universal controlled by one switch (ISI Marked) complete all as specifed and directed.

Socket outlet 2 in 1, 5 pin, 5A, flush type universal, all as specified and as directed. Make:Havells/Anchor

Socket outlet 2 in 1, 6 pin, 5/15A, flush type universal, all as specified and as directed. Make: Havells /Anchor

LED bulb 7 Watts, 6500 K complete all as specified and directed. Make : havells / anchor / Surya/Cropmton

Submain wiring with two single core 4 Sqmm PVC FRLS insulated and unsheathed 1100 volts grade multistranded copper conductor ISI Marked drawn into & including medium grade PVC conduit /casing capping, with wooden/white color casing capping (as specified and directed) 25 mm dia with all fittings and accessories and continuous run of one single core PVC FRLS insulated unsheathed multistranded copper conductor cable green colour of size 2.5 Sqmm as earth lead in & including PVC casing capping/ conduit (not less than 25 mm outer dia) with all fittings and accessories fixed concealed/surface including taking down old unserviceable sub main wiring and making good surfaces to match with existing specification all as required at site complete all as specified and directed by Engr-in- charge. Make of cable - Havells/Plaza/Policab and Make of Casing capping - Polyplast/Pressfit/Presto plast

Submain wiring with two single core 2.5 Sqmm PVC FRLS insulated and unsheathed 1100 volts grade multistranded copper conductor ISI Marked drawn into & including medium grade PVC conduit /casing capping, with wooden/white color casing capping (as specified and directed) 20 mm dia with all fittings and accessories and continuous run of one single core PVC FRLS insulated unsheathed multistranded copper conductor cable green colour of size 1.5 Sqmm as earth lead in & including PVC casing capping/ conduit (not less than 20 mm outer dia) with all fittings and accessories fixed concealed/surface including taking down old unserviceable sub main wiring and making good surfaces to match with existing specification all as required at site complete all as specified and directed by Engr-in- charge. Make of cable - Havells/Plaza/Policab and Make of Casing capping - Polyplast/Pressfit/Presto plast

Taking down UNSV Bulk Head fitting by carefully unscrewing from boarda/outlet boxes,fitting and fixture and carrying to store for schedule of credit

Sheet metal enclosure for TPN DBs (double door type), when MCCBs to be used Triple poles and neutral 4 to 12 way incl blanking plate as reqd with 200 amps rated busbar 240V complete all as specified and directed. Make : Legrand, Havells/HPL.

MCCB / RCBO four pole 16 to 63 Amps (as directed at site ) 415 Volts, 16 KA, complete all sa sepcifed and directed . Make-Havells/Legrand/L&T

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 03 of 2009 SSR Pt-I and testing on complete including earth work in any type of soil, PCC 1:2:4 type B-0 as in earth pit and cover 40mm thick reinforced with XPM (weight not less than 4.0Kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, common salt, charcoal and testing on completion, all as specified and directed.

Supply and fix water heater storage type, electric capacity 35 litres, BEE 5 star rated , with copper/glass lined stainless steel tank,along with associated plumbing, mechanical and electrical fittings instructed by Engr-in-Charge. Make-Havells/Recold/Usha

Supply, laying and testing of XLPE insulated screened, PVC bedded galvanized steel strip or wire armoured electric power cables (heavy duty) with aluminium conductor 1100 volts grade, cross sectional area 16 sqmm 4 core complete all as specified and directed.Make:- Havell's/ Fort Gloster/Poly Cab.

Sheet metal enclosure for SPN DBs (double door type), when MCBs to be used single pole and neutral 8 way incl blanking plate as reqd with 200 amps rated busbar 240V complete all as specified and directed. Make : Legrand, Havells/HPL.

MCB single pole & neutral 20 to 40 Amps 230 Volts'C' series, 10 KA complete all as specified and directed.Make: Havels /Legrand L&T.

MCB single pole 6 to 32 Amps 230 Volts'C' series, 10 KA complete all as specified and directed. Make: Havels /Legrand L&T.

Bathroom mirror lamp,10 watt, with designer, glass cover, enamelled bronze base, with LED lamp, includings necessarry wiring and accessories required , PVC / polcarbonate isolated body.

S & F in replacement LED batton T-8 Endura liner NEO with tube rod with surface and wall mounted, extruded aluminium housing provided for efficient heat with polycarbonate diffuser and integrated electronic driver' 20 watts 4 fits complete all as specified and directed. Make Havells, Wipro and Philips,

S&F in replacement Linear & compact 9/10W LED light with decorative grey end caps, polycarbonate body and ribbed opal anti glare diffuser with heat resistant toughed glass, corrosion resistant, isolated driver. Make-Havells/Philips/Bajaj/Wipro/CG

Taking down celing fan /exhaust fan complete including ovehauling, cleaning with soft dolution and painting of the same with white enamelled paint including painting of MES number as existing, or rehaning celing fan / exhaust fan and connecting up including provision of three core copper conductor cable 1.5 sqmm nominal cross sectional area and length not less than 0.5 mtr from ceiling rose to fan complete all as specified and directed

S&F in in repair streets light bracket bend to shape made out of 40 mm dia 1.5 mtr long GI pipe light to wall with the help of flat iron 40x6 mm two nuts and bolts for fixing of building security light fitting all as specified and directed.

S&F in replacement security (street) light fitting 30watt, new generation energy saving & environmental friendly long life versatile pressure die cost aluminium IP 66 with acylic, powder coated, pressure die cast aluminium compact high power LED street light with heat resistant toughed glass, corrosion resistant, isolated driver, complete all as per direction of Engr-in-Charge. Make:SYSKA/Wipro/Havells

Heavy duty exhaust fan 300 mm sweep ,rated voltage 220-240V, 50 Hz, steel/plastic body with louver shutter, wall mounted type complete with power cord, plug top etc. complete all as specified and directed. Make-Havells/Khaitan/Usha

LED Bulk Head luminaires, designer type, with 6.5 Watts 600k lights and IP55 in engineering plastic housing with prismatic diffuser, complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V, 50 HZ. Make of light fitting - C&S, Philips, Syska, Wipro or equivalent as approved by engineer in charge.

Excavation in trenches in any type of soil n.exc 1.5m deep and not.exc 1.5m wide for laying of under ground cable, electric pole and getting out complete all as directed.

Returning filling in including spreading leveling watering and well ramming 25cm in thickness in any type of soil.

Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point.

Dry sand cushioning to under ground cables provided with a layer of sand 8 cm deep before laying the cable, 15 cm depth after laying cable & stretching the cable all as specified and directed.

Supply and leying brick class ‘B’ covering as mechanical protection to cable with well burnt all as specified.

GI tubing light grade with all fitting and fixed in wall and floor or fixed to pole of size 40mm dia.

RATHER BROTHERS

Bidder Name

RATHER BROTHERS

POPULARHARDWARESTORE