SPECIAL REPAIR TO BLDG NO P 134 AT AUNDH MILITARY STATION UNDER GE MH AND RH KHADKI

Amount

M&L PCC 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregates) for filleting, benching, slightly rounding or chamfering on edges, filling undulations / depressions in roof surface, providing concrete platform for tanks wherever required all as specified & directed.

Taking down / removing existing water proofing treatment from RCC roof slab including removal of plaster bed below felt / membrane and disposal of the same to a distance exceeding 50m but not exceeding 100m as and where directed and M&L for 10 mm thick screeding / rendering in cement mortar 1:3 on concrete roof surface, using Water Proofing Compound @ 3% by weight of cement, surface finished even and smooth without using extra cement all as specified & directed. Note: Water Proofing Compound shall be measured and paid separately.

Supply only intergral water proofing compound.

M&L for Cutting out cracks to "V" section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 all as specified & directed.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 0.3 kg per sqm including cleaning surfaces over RCC slab and providing and lying APP based polymeric membrane minimum weighting 3 Kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) laid on primed surface with 10 cm overlap both ways by forced application complete all as specified and applying two coat of solar reflective aluminium paint@ 100ml per Sqm per coat on membrane surfaces complete all as specified and as directed by Engineer in charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level ) all as specified and directed

M&L for waterproofing treatment to RCC sunken slab as specified below. Make: PIDILITE, Dr Fixit or equivalent. a) Clean the sunken portion of toilet/Bath/WC/Kitchen thoroughly to remove laitance, dirt , dust etc b) Form angle fillet of size 40 mm x 40mm along the junction of wall and floor using polymer modified mortar ("Dr Fixit" Pidicrete URP" or equivalent) c) Sanitary pipes entering through walls and floor shall be sealed with " Dr Fixit Bathseal Tape" and the gaps to be grouted with non-shrink cementitous grout " Dr Fixit Bathseal Gruot" or eqvt . Nahani traps , etc to be fitted securely and the gaps around it to grouted in the same manner. d) Apply one coat of a Bitumen- modified polymer coating " Dr Fixit Bathseal Plus" or eqvt on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely. e) In the remaining area, in dry substrate condition brush apply first coat of the same coating and further apply second coat when first coat is dry. Extend the coating upto 150mm above the FFL. Above FFL, another cementitious waterproof coating " Dr Fixit Pidifins 2K" or eqvt can be further applied right upto 2.1 m to waterpoof the shower area also , if it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6-8 hours allow to dry completely. f) After 2 to 3 days, sunken portion must be overlaid with a 50mm thick concrete screed M 15 type B0 mixed with integral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40mm OD UPVC pipe at the lowest point with 300mm projection beyond the outer face of the wall. Then fill up the sunken portion with lean concrete 1:5:10 type E2, all as specified and directed. (g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready to make tile grouts of appd makes such as Dr Fixit, FOSROC , SIKA, MC BUCHEMIE, ROFF etc , all as specified and directed.(Note:- Tiling work will be measured and paid separately)

M&L PCC (1:5:10) type E2 (using 40mm graded crushed stone aggregate as in mass concrete or as in sunken portion or floor all as specified & directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing coat) all as specified and directed.

M&L 25 mm thick PCC 1 :2 : 4, type B0 ( Using 12.5 graded crushed stone aggregate) as in base of floors all as specified and as directed by Engineer-in-Charge.

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles including 15mm thick in CM (1:6) Screed bed or bedding layer of mortar for laying floor finishes all as specified and directed.

M&L Coloured Glazed ceramic tiles 600X300X7 mm thick, on vertical surfaces such as skirting, dados and risers to steps, etc. set and jointed in neat cement slurry and pointed in white or Coloured cement to match the shades of the tiles including 10mm thick rendering in CM 1:4 all as specified and directed.

M&L Coloured Vitrified tiles 8 to 10mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tile laid over and including 15 mm thick screed bed in CM 1:6 all as specified and directed.

All as per item No 13 above but as in skirting laid over 10 mm thick rendering in cm 1:4 all as specified and directed.

Demolition of brick work or stone masonry or block masonry built in cement or cement/lime mortar all as specified and directed.

M&L for PCC solid block masonry of blocks of type C1 (using 20mm graded crushed stone aggregate) (1:3:6) wall exceeding 10cm in width & built in CM (1:6) all as specified and directed.

Dismantling of old stone slab of any description all as specified and directed.

M&L for 20mm thick Granite slab machine cut, laid over cement screed and jointed with grey cement slurry and pointed with white or colour cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete including screed bed 15mm thick in CM 1:4 all as specified and directed.

M&L for 20mm thick Granite slab machine cut in dado/skirting, laid over cement screed and jointed with grey cement slurry and pointed with white or coloured cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete including rendering of 10mm thick in CM 1:4 all as specified and directed.

M&L for 20-25mm thick machine cut cuddappah stone as in slab flooring laid over cement screed bed laid and jointed with grey cment slurry mixed with pigment to match the shade of the slab including grinding and polishing laid over 15 mm thick screed in CM 1:6 all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as specified and directed.

M&L machine cut kota stone slab flooring 20-25mm thick in flooring but one piece as in treads of straircase etc. laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, over 15 mm thick screed bed or bedding in CM 1:6 for laying floor finishes all as specified and directed.

All as item No 22 here in before but in skirting but one piece for step riser over and including 10 mm thick rendering in CM 1:4 to receive kota stone/slab all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls, ceilings, etc. including raking out joints, hacking for key, scrubbing down with water all as specified and directed.

M&L 15 mm thick plastering in cement mortar 1:4 on external plaster, finished the surfaces even and smooth (upto any height) by using 3% of WPC of weight of cement used or as per manufacturer instruction all as specified and directed.

M&L for preparation of new surfaces and applying finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) all as specified and directed.

M&L for complete removal of existing treatment, preparing the surfaces and applying finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) all as specified and directed.

All as per item No. 25 above but 5 mm thick in CM 1:4, finished surfaces even & smooth with thin layer of sagol finish but as in ceiling all as specified and directed

M&L for applying three coats of white wash on ceiling including preparation of new surfaces all as specified and directed.

M&L for applying one coat of white wash on celing on old surfaces including preparation of old surfaces including cleaning smoke efflorocense of any type or spot of nail filled with putty complete to match with old surfaces all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces including finishing the surfaces even and smooth with a thin layer of sagol all as specified and directed.

M&L for preperation of new plastered surfaces & applying two coats of oil bound distember over a coat of alkali resistant primer all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of oil bound distemper on walls over a coat of alkali resistant primer including preparation of old surfaces, on plastered surfaces prepratary to distempering all as specified and directed.

M&L for preparation of new surfaces of wall and applying three coats of white wash all as specified and directed.

M&L for complete removal of existing treatment and applying three coats of white wash on walls including preparation of old surfaces all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exc 1.50 Sqm but n. exc 4.00 Sqm all as specified and directed.

S&F Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate all as specified and directed.

M&L PCC type B0, 1:2:4 (using 12.5 mm graded crushed stone aggregate) in door and windows frames, of any size, single or double rebated, including fixing arrangement for fixing of hinges and fixtures as required all as specified and directed.

M&L for flush shutters 30mm thick solid core constructions with block board core, ply wood face panels commercial type on both side all as specified and directed.

S&F to chowkats 2nd class HW 35 mm thick factory made Gauzed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section 200 mm long all as specified and directed.

S&F Aluminium handles, cast type, anodised size 150 mm long all as specified and directed.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and directed.

S&F Mild steel Butt hinges100 mm long, medium weight, cold rolled mild steel all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of width or girth exceeding 10 cm including preparation of surfaces all as specified and directed.

M&L for preparation of surfaces and applying one coat of synthetic enamel paint on old wooden surfaces of width or girth exceeding 10 cm all as specified and directed.

Taking down shutter from frame area exc 1 but n.exc 2 Sqm each and removing from the site all as specified and directed

S&F Solid PVC door frame of size 50mm X47 mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube suppling and fixing in opening as per specification and drawing.

S&F MS Butt hinges 75 mm long, medium weight, cold rolled mild steel all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip if 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bootom rail on either side & as a gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling and fixing in the frame at site as per specification & drawing all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section 125mm long all as specified and directed.

S&F Aluminium handles, cast type, anodised size 125 mm long all as specified and directed.

Taking down steel window chowkat with shutters without taking off shutter from the frame area n.exc 1.5 sqm each all as specified and directed.

S&F Powder coated aluminium window sliding type (3 track) with frame size100x35x1.2mm and shutter 39.40x17.70x1.2mm with tow glass shutter & one mesh shutter including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with 4mm plain float glass & 0.56 mm all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixing to new steel window with nut bolt all as specified and directed.

M&L for preparation of new steel surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

S&F Powder coated aluminium louvered ventilators of section size 100mmx25mmx1.50mm including frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc. all as directed by Engr-in-Charge.

M&L for preparation of old steel surfaces area exc 10 cm width or girth and applying one coat of synthetic enameled paint all as specified and directed.

M&L for each spot welding upto 30 mm for repairing steel windows, shutter and ventilators hinges, brackets, steel handle, grill all as sepcified and directed.

S&F in repairs powder coated aluminuium pipe 20 mm dia as in curtain rod fixed to brackets all as specified and directed. Note:- brakets shall be measured and paid separately.

S&F in repairs powder coated aluminium brakets fancy type for curtain rods of 20mm dia all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections including disconnection of fittings and cleaning for refixing where required all as specified and directed.

All as per Item No. 63 above but 20 mm dia pipe

S&F 15 mm bore GI pipe medium grade steel tubes, galvanised with & including all fittings and fixtures fixed complete to concealed walls and ceilings or laid in floors all as specified and directed.

All as per item No. 65 above but except steel tubing.

S&F 20 mm bore GI pipe medium grade steel tubes, galvanised with & including all fittings and fixtures fixed complete to walls and ceilings or laid in floors all as specified and directed.

S&F in repairs Rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe all as specified and directed.

S&F in repairs Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe all as specified and directed.

S&F in repairs Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both ends for iron pipe all as specified and directed.

S&F in repairs 20mm dia bore Gun metal, globe or gate valves with Iron wheel head, screwed both ends for Iron pipe all as specified and directed.

S&F in repairs 15 mm angle stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and directed.

S&F in repairs 15 mm stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions but fancy type with long shank and cup ( concealed type) all as specified and directed by Engineer in Charge.

S&F in repairs 15mm dia fancy type Bib taps, cast copper alloy CP with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and directed.

S&F in repairs Chromium plated shower roses with or without swivel joints, 125mm size, including fixing to steel pipe or union all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts of 600 mm long all as specified and directed.

S&F in repairs PVC (SWR) pipes 110mm dia, single socketed in any length with rubber ring joints laid in trenches or floor all as specified and directed.

S&F in repairs PVC (SWR) pipes 110mm dia, single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

S&F in repairs PVC (SWR) pipes 75 mm dia, single socketed in any length with rubber ring joints laid in trenches or floor all as specified and directed.

S&F in repairs PVC (SWR) pipes 75 mm dia, single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

S&F in repairs PVC (SWR) bends any radius, for 110mm dia pipe all as specified and directed.

S&F in repairs PVC (SWR) bends any radius, 75mm dia pipe all as specified and directed.

S&F in repairs PVC (SWR) branch piece, single (single Y) equal or unequal for 110mm dia pipe all as specified and directed.

S&F in repairs PVC (SWR) branch piece, single (single Y) equal or unequal for 75mm dia pipe. all as specified and directed.

S&F in repairs PVC (SWR), junction single, (Single T) equal or unequal for 110mm dia pipe.

S&F in repair PVC (SWR), junction single, (Single T) equal or unequal,75mm dia pipe.

S&F in repairs Vitreous China Squatting pan Orissa pattern long pan, size 580 mmX440mm white with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including concrete complete and making good to floor all as specified and directed.

S&F in repairs wash down water closet ( European type) excluding fixing bolts, flushing cistern & flush pipe but including connecting to existing out let pipe all as specified and directed.

S&F in repairs PVC valveless syphonic action type flushing cistern (Low or high level) of 10 litre capacity, white/coloured with inlet, ball valve, float, handle including fixing brackets and 32 mm bore PVC flush pipe all as specified and directed.

S&F in repairs vitreous china wash basin white, flat back of size 450 x 300mm, excluding taps, waste chain & plug & porcelein stopper but including brackets, cutting for and pinning in ends of brackets all as specified and directed.

S&F in repairs 15mm dia brass CP Wall mixer for mixing hot & cold water screwed down for iron pipe and fixed of make CERA cat part No F 2010403 or techno commercially equivalent models in makes all as specifeied and directed

S&F in repairs pillar taps fancy type cast copper alloy with capstan heads chromiun plated screwed down high pressure with hot & cold with long screwed shanks and fly nuts all as specified and directed.

S&F in repairs stainless steel sink with drainage board, 1mm thick, kitchen or laboratory with plugs, washers and waste; including PVC waste pipe, bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm all as specified and directed.

S&F in repairs stainless steel sink, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever bracket of 495mm x 420mm, bowl size 410mm x 330mm x 160mm all as specified and directed.

S&F in repairs plate rack made of stainless steel 1mm thick and overall size 915mm x915mm x 255mm all as specified and directed.

S&F in repairs tubular towel rail 20mm dia, D type 60cm long between flanges brass chromium plated all as specified and directed.

M&L in repairs 100 mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) all as specified and directed.

S&F in repairs 18-19mm thick Prelaminatd particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as sepcified and directed.

S&F in repairs Contineous Piano hinges 30mm width of flaps (when open), mild steel, bright finish or electrogalvanised all as specified and directed.

S&F in repairs Hasp and staple 150mm long, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws all as specified and directed.

S&F in repairs 75mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed all as specified and directed.

S&F in repairs 100mm long Aluminium handles, cast type, anodised all as specified and directed.

S&F in repairs grating square or circular 125mm dia of PTMT (minimum weight 100 gms) all as specified and directed.

Excavation in trenches not exceeding 1.50m wide and 1.50m depth for foundation, etc., for Shaft wells, Manholes etc not exceeding 10sqm on plan and not exceeding 1.50m in depth and getting out in soft / loose soil all as specified and directed.

All as per Item No 105 above, but for depth exceeding 1.5m and not exceeding 3.0 m in soft/loose soil.

Returning filling in including spreading leveling watering and well ramming in layers not exceeding 25cm thick with soil obtained from excavation all as specified and directed.

Removing excavated surplus soil not exceeding 50m and depositing where directed at a level exceeding 1.5m above the starting point all as specified and directed.

Demolition and breaking up drain pipes of 150 mm bore RCC/SGSW set in cement mortar including removing the debries to a distance n exc 100m all as specified and directed.

All as per item No. 109 above but dia of pipe 200mm.

M&L PCC C2 1;3:6 type C2 (using 40 mm graded crushed stone aggregate) as in concrete bed to drain pipes including packing under and haunching against sides of pipes with concrete after they are laid and bedded dia of pipe 150mm all as specified and directed.

All as per item No. 111 above but dia of pipe 200mm.

M&L 150mm dia RCC drain pipes class NP2 laid in trenches and jointed with in cement mortar all as specified and directed.

All as per item No. 113 above but dia of pipe 200mm.

M&L cutting to existing manholes 150mm dia for connecting new drain, making good to pipe and rendering, cutting out existing benchings for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1, (using 20mm graded crushed stone aggregate), smooth finished and reforming benching as required for internal dia of pipe 150mm all as specified and directed.

S&F in repairs RCC precast Sewage manhole cover Medium duty grade of size 450x900mm thickness 50 mm and set the same at the site including removing old from site in any position all as specified and directed.

S&F in repairs RCC Precast round Sewage manhole cover Medium duty Grade of size 600mm dia thickness 60 mm heavy duty and set the same at the site including removing old from site in any position all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate), 75 mm thick as in plinth protection with construction joints filled with bitumen masticall as specified and directed

M&L 75mm PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregate) as in sub base of floor all as specified and directed.

M&L in repairs prepolished Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in near cement slurry in floors with grey cement and pigment including 20mm thick screed bed in CM 1:6 all as specified and as directed.

S&F in repairs bathroom cabinet mirror (of approved pattern) of size 450mmx 350mm regular size with mirror and PVC shelves all as specified and directed.

S&F in repairs perforated cutlery basket of size 530 x 505 x 100mm fabricated purpose made with each sanless steel of grade 340, not less than 6 to 8 kg each rack using square hollow tubes for frame work and solid round bars /26 guage thick sheet to make desired pattern, suitable for sliding under kitchen platform on a pair of channels including fixing with steel screws all as specified and directed by Engineer in Charge. Note : Telescopic channels shall be measured and paid seperately under respective items of BOQ. Make : Asian/Godrej/Hettich

S&F in repairs stainless steel cup & Saucer 530 x 505 x 100mm fabricated purpose made with each stainless steel of grade 340, not less than 6 to 8 kg each rack using square hollow tubes for frame work and solid round bars 26 guage thick sheet to make desired pattern, suitable for sliding under kitchen platform on a pair of channels including fixing with steel screws all as specified and directed by Engineer in Charge. Note : Telescopic channels shall be measured and paid seperately under respective items of BOQ. Make : Asian/Godrej/Hettich

S&F in repairs stainless steel perforated thali of size 530 x 505 x 200mm fabricated purpose made with each stainless steel of grade 340, not less than 6 to 8 kg each rack using square hollow tubes for frame work and solid round bars 26 guage thick sheet to make desired pattern, suitable for sliding under kitchen platform on a pair of channels including fixing with steel screws all as specified and directed by Engineer in Charge. Note : Telescopic channels shall be measured and paid seperately under respective items of BOQ. Make : Asian/Godrej/Hettich

S&F in repairs stainless steel plain basket of size 710 x 505 x 200mm fabricated purpose made with each stainless steel of grade 340, not less than 6 to 8 kg each rack using square hollow tubes for frame work and solid round bars 26 guage thick sheet to make desired pattern, suitable for sliding under kitchen platform on a pair of channels including fixing with steel screws all as specified and directed. Note : Telescopic channels shall be measured and paid seperately under respective items of BOQ. Make : Asian/Godrej/Hettich

S&F in repairs stainless steel fixed pull out 3 shelf fabricated purpose made with each stainless steel of grade 340, not less than 6 to 8 kg each rack using square hollow tubes for frame work and solid round bars 26 guage thick sheet to make desired pattern, suitable for sliding under kitchen platform on a pair of channels including fixing with steel screws all as specified and directed. Note : Telescopic channels shall be measured and paid seperately under respective items of BOQ. Make : Asian/Godrej/Hettich

S&F in repairs fixed multipurpose double tier 456 x 170 x 450mm fabricated purpose made with each stainless steel of grade 340, not less than 6 to 8 kg each rack using square hollow tubes for frame work and solid round bars /26 guage thick sheet to make desired pattern, suitable for sliding under kitchen platform on a pair of channels including fixing with steel screws all as specified and directed by Engineer in Charge. Note : Telescopic channels shall be measured and paid seperately under respective items of BOQ. Make : Asian/Godrej/Hettich

S&F in repairs telescopic channels soft closing powder coated with ball bearings, suitable for sliding SS plate racks, 60cm long, standard width, fixed over second class hard wood rectangular fillets sectional area exc 3 sqcm and n.exe. 6 sq cm, clean swan secured with screws and the fillet fixed on Cuddappa stone with screws all as specifed and as directed . Make : Asian/Godrej/Hettich

S&F stainless steel handle oval shape fabricated type anodized 150mm long of approved design, shape and make fixed with nut screws and washers complete with ISI all as specified and as directed. Make : Asian/Godrej/Hettich

S&F stainless steel finish soft closing hinges approved design, shape and make fixed with nut screws & washers complete with ISI mark all as specifed and as directed. Make : Asian/Godrej/Hettich

S&F in repairs 18mm thick marine plywood as per IS 710 laminated of any colour with high glossy acrylic sheet of 3mm thick grade I of frame & shutter for kitchen cabinet all specified and as directed. Make : Asian/Godrej/Hettich

Dismantling wrought iron or mild steel work of any description not othervise provided for all as specified and directed

M&L for framed work as in doors or gates of angle Gde-Fe-290( Gde-E-165) or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc to match with the existing surfaces all as specified and directed.

M&L for point wiring complete with 1.5 Sqmm single core FRLS PVC insulated unsheathed cable 1100 V grade multi stranded copper conductor drawn through non metallic rigid PVC conduit and accessories concealed in walls/ceilings including 1.5 Sqmm dia multistranded copper cable as earth continuity conductor connected to common earth dolly, including 1.22 mm thick pressed steel terminal boxes to provision of Modular switches to house switch/regulators etc including Modular Plate and Covers for one fan/light /bell point controlled by one switch/bell push all as specified and directed.

All as per item No 135 above but for one 3 pin 5 Amps socket on same board controlled with other switches

All as per item No 135 above but for one 3 pin 5 Amps socket on independent board

All as per item No 135 above but for one light point controlled by two way switch all as specified and directed.

All as per Item No 135 here-in- before but with 2.5 Sqmm PVC insulated multistranded copper conductor with 2.5 sqmm cable as earth continuity conductor for Power Socket on independent board on the Concealed conduit all as specified and directed.

All as per Item No 135 here-in- before but with 4 Sqmm PVC insulated multistranded copper conductor with 4 sqmm cable as earth continuity conductor for Power Socket/AC/Geysers on independent board on the Concealed conduit all as specified and directed.

S&F modular switch 1 way 6A, 1 module all as specified and directed.

S&F modular switch 2 way 6A, 1 module all as specified and directed.

S&F modular bell push 6A, 1 module all as specified and directed.

S&F modular socket 6A, 2/3 pin combined, 2 module all as specified and directed.

S&F modular socket 16A, 2/3 pin, combined 2 module all as specified and directed.

S&F modular switch 1way, 16A, 1 module all as specified and directed.

S&F Modular fan step regulator 120 w -2 module all as specified and directed.

S&F electric bell Ding Dong, AC 230 volts all as specified and directed.

S&F ceiling rose surface bakelite with three terminals all as specified and directed.

S&F LED fitting for Bldg security, 35 Watt 230 V, AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65 / 66 protection complete, including conncting with 1.5 sq mm copper condector 3 core flexible cable from fitting connector to ceiling rose and fix on wall with clamps & nut bolts and necessary GI bracket made of 32 mm light grade GI pipe of 1 mtr lenth with necessary bending all as specified and directed .

Taking down old unserviceable Tube light fitting of any type and Supply and fixing LED lights fitting 1x 22W, 220V, AC, decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose all as specified and directed. Make :- Philips/Havells/Orient Note :- The rates are inclusive of cost of square box including suitable size of clamps and screws etc.

Taking down old unserviceable Tube light fitting of any type and S & F wall/ceiling mounted LED tube light fitting , Energy efficient high quality invertor batten having Lithium ion battery of 3.7V, 19 WH for backup upto 2Hrs with high power brightness having BIS certification, LED fitting should be LM 80 certified with system efficacy greater than 100 lumens/watt, including LED tube 22 watt having colour temperature 6500 K (4 feets long) , PF> 0.95, THD less 10%, with IP20 protection having open and short circuit protection, having input voltage range 90V to 300V connecting with three core flexible copper wire from connector to ceiling rose/angle holder as per existing site requirement as directed by Engr-in-charge. Make : Jaquar/Halonix/Philips . Note :- The rates are inclusive of cost of square box including suitable size of clamps and screws etc.

Taking down old unserviceable LED Light fitting mirror type & S&F LED Light fitting mirror type with high output diffuser 2 feet, 1 X 10 watt 220V, AC decorative type with driver holder and LED lamp, Alluminium housing, including connecting up with flexible copper conductor cable of suitable size all as specified and directed. Make :- Philips/Havells/Orient

Taking down old unserviceable wall bracket light fitting of any type & S&F wall mounted high quality indoor wall bracket light cylinderical/oval shape aesthetically designed fitting in wooden housing, glass and B22 holder complete including inverter LED bulb B-22 cap with opal diffuser, IP-20 and inbuilt battery backup (LED INVERTER LIGHT 10W B22 CW IP) 10 watts including necessary eletric connection with PVC insulated multistranded copper cable of sutaible size to fitting terminal all as specified and directed.

Taking down unserviceable submain wiring and M&L for submain wiring in PVC conduit concealed in walls/ceilings with two runs of 6 sq mm and one runs of 6 sqmm for earth continuity 1100 v grade PVC insulated unsheathed FRLS grade copper conductor cable single core multistranded ISI marked (IS 694) drawn through and including 25 mm dia PVC rigid connduit heavy grade ISI marked (IS 9537 Part III) includung accessories such as bends, supports etc all as specified and directed. Note: Two runs of 6 sq mm and one runs of 6 sqmm cable along with conduit shall be measured as one length.

S&F in repairs MCB DB SPN 12 way of any size and capacity double door type horizontal with 200A busbar including disconnecting from mains and making good the disturbed surfaces all as specified and directed.

S&F in repairs MCB SP of capacity 6A - 32A 'B' curve all as specified and directed.

S&F in repairs MCB, SPN (Double Pole) 32 amps, 240 Volts, 10 KA ‘’C” curve all as specified and directed.

M&L for earthing complete with 600x600x6mm galvanised steel earth plate electrode buried vertically in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the plate at a depth of not less than 1.5m below ground level, connected to and including G.I. wire of size 4 mm dia by means of bolts, nuts and check nuts and washers of galvanised steel, GI pipe 15 mm dia light grade pipe for protection of GI earth lead wire both to be provided to the extent of 7.5 metres as earthing lead and connecting to the eqpt/machinery etc. including charcoal dust and common salt packed all around the earth plate in alternate layer in the earth pit all as per electrical plate No. 3 of SSR Part I-2009 including PCC chamber made up of PCC 1:3:6, type C1 & RCC Chamer cover of size 540x540x100 mm made with 1:2:4, Type B1 using 8 mm TMT bar for reinforcement and handle, 20 mm dia medium grade G.I. watering Pipe from top edge of the earth plate upto M.S. funnel with wire mesh provided inside the concrete earth pit for watering arrangement including excavation and earth work in any type of strata and testing on completion all as specified and directed.

Taking down old unserviceable Exhaust fan and depositing it to MES store and Supply and fix Exhaust fan steel body AC single phase, 230 volts of size 380 mm sweep with blades and frame and louvers complete all as specified and directed. Make: Havelles, CG, Usha, Orient. Note : (i) To be Fixed in Existing kitchen window (ii) The rates are inclusive of any civil work required to fix the exhaust fan. (iii) Contractor has to visit the site of the bldg where exhaust fan is to be fixed befour quoting the tender

Taking down old unserviceable exhaust fan and depositing it to MES store and Supply and fix Exhaust fan steel body AC single phase, 230 volts of size 300 mm sweep with blades and frame and louvers all as specified and directed. Note : (i) To be Fixed in Existing Toilet window (ii) The rates are inclusive of any civil work required to fix the exhaust fan. (iii) Contractor has to visit the site of the bldg where exhaust fan is to be fixed befour quoting the tender

Taking down old unserviceable ceiling fan and depositing it to MES store and Supply and fixing new ceiling fans complete with blades, down rods, electronic regulator/remote and connected accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) all as specified and directed.

S&F single pole and neutral enclosure with a two pin and earth plug and socket complete with 20 Amp DP MCB all as specified and directed.

Taking down existing serviceable kwh meter from site without any damage cleaning it properly and refixing the same in the new panel as directed by Engr-in-charge of the each block after completion of work all as specified and directed.

Dismantling old water geyser of any type/capacity and depositing it to MES store and Supply and fix (Geyser) Water heater storage type of capacity 25 Liters vertical type wall mounted including 15/16 Amps plug top with suitable wall supports and for manual operation, digital temperature display, feather touch buttons, built in thermostat, auto shut off, powder coated single line weld container with PUF insulation, heating element capacity of 2 KW, voltage rating 230 Volt, frequency 50 Hz, 5 star rated with and including steel braided connecting hoses of required length for Hot and cold water pipe, connecting to CPVC and GI pipe all as specified and directed by Engr-in-Charge. Make: Havells/Jaquar/Crompton/Bajaj. Note :- (i) The rates are inclusive of all the minor spares (Fasteners, Nut bolts washers etc) required for making the geyser fully functional.

S&F Hot water pillar taps 15 mm bore cast copper alloy with capstan heads, chromium plated, screwed down high pressure with lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed all as specified and directed by Engr-in-Charge.

S&F Stop Valves, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions and fixed of size 15 mm all as specified and directed by Engr-in-Charge.

VP DEVELOPERS AND CONTRACTOR (BID ID -3445918)

MAHESH DADAJI BACHHAV (BID ID -3445971)

J.B.ENTERPRISES (BID ID -3445417)

S.R.M.K Enterprises (BID ID -3446043)

M/S JAYCONSTRUCTION CO (BID ID -3446152)

UNIQUE ENGINEERS (BID ID -3451665)

Bidder Name

UNIQUE ENGINEERS

J.B.ENTERPRISES

S.R.M.K Enterprises

M/S JAYCONSTRUCTION CO

MAHESH DADAJI BACHHAV

VP DEVELOPERS AND CONTRACTOR

ShreHari Civil Enginneering and Contractors