DAY TO DAY MAINTENANCE OF PLUMBING, SANITARY ITEMS, BATH FITTINGS, FALSE CEILINGS WORKS, PETTY REPAIRS AND OTHER BR WORKS AT RANGIA MILITARY STATION UNDER GE RANGIA

Amount

Taking down chowkat or frame exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutter from the frame), complete all as specified and as directed by Engineer-in-charge.

Taking down chowkat or frame not exceeding 1.5 Sqm each (without taking off shutter from the frame), complete all as specified and as directed by Engineer-in-charge.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each, complete all as per specified and as directed by Engineer-in-charge.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and as directed by Engineer-in-charge.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing, complete all as specified and as directed by Engineer-in-charge.

Demolition of unreinforced cement concrete in ground floors and pavings not exc. 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as per specified and as directed by Engineer-in-charge.

Dismantling water tanks of capacity exc. 250 and not exc. 500 ltrs, complete all as per specified and as directed by Engineer-in-charge.

Dismantling water tanks of capacity exc. 500 and not exc. 1000 ltrs, complete all as per specified and as directed by Engineer-in-charge.

Taking up or down 15 mm bore steel tubing and connections, complete all as per specified and as directed by Engineer-in-charge.

Taking up or down 20 mm bore steel tubing and connections, complete all as per specified and as directed by Engineer-in-charge.

Dismantling Unframed timber scantlings 40 Sqcm and over in section and in any position, complete all as specified and as directed by Engineer-in-charge.

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-in-charge.

Demolition of brick work built in any cement mortar complete all as specified and as directed by Engineer-in-charge.

S&F Mild steel work as in bands, straps, supports or stays for rainwater, clamps, hold fasts, wall ties, hooks for hanging fans and similar work conforming to Fe-290 Gde-E-165 complete all as specified and as directed by Engineer-in-charge.

S&F second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as per specified and as directed by Engineer-in-charge.

M&L 2nd class hard wood in scantling wrought timber unframed and fixed, complete all as specified and as directed by Engineer-in-charge.

M&L 6 mm thick Asbestos Cement sheet, corrugated, or semi corrugated sheets in roofs, walls etc. and fixed with fixed with L-type or J-type or cranked hook bolts, complete all as specified and as directed by Engineer-in-charge.

Fixing only Asbestos Cement sheet, corrugated, or semi corrugated sheets in roofs, walls etc. and fixed with L hook or Cranked bolts (except sheets), complete all as specified and as directed by Engineer-in-charge.

M&L for 6 mm thick Asbestos cement serrated ridge for corrugated and semi corrugated sheets fixed with L-type or J-type or cranked hook bolts, complete all as specified and as directed by Engineer-in-charge.

M&L for PCC 1:3:6 type C-1 (20mm graded stone aggregate) as in fillings of chowkats hold fast or similar nature of works complete all as per specified and as directed by Engineer-in-charge.

S&F 35 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides, complete all as per specified and as directed by Engineer-in-charge.

S&F 30 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass gauge etc. divided into squares with plain chamfered or rounded, rebated sash bars, sizes of the members of the shutters as specified in SSR Part-I complete all as per specified and as directed by Engineer-in-charge.

S&F 100 mm long medium weight, cold rolled mild steel butt hinges, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. .frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as per specified and as directed by Engineer-in-charge.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube in opening complete all as per specified and as directed by Engineer-in-charge.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed by Engineer-in-charge.

S&F 100 mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed by Engineer-in-charge.

S&F aluminium handle cast type anodised 150mm size complete all as specified and as directed by Engineer-in-charge.

S&F aluminium handle cast type anodised 125mm size complete all as specified and as directed by Engineer-in-charge.

S&F stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with tinned stacks, or galvanized wire staples complete all as per specified and as directed by Engineer-in-charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and as directed by Engineer-in-charge.

S&F 3 mm thick sheet glass, ordinary quality in squares not exceeding 0.5 Sqm in each pane fixed with cut & mitred beads, complete all as specified and as directed by Engineer-in-charge.

S&F 3 mm thick figured glass in squares not exc. 0.5 sqm in each pane glazing with oil putty complete all as per specified and as directed by Engineer-in-charge.

S&F GI tube 15 mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and as directed by Engineer-in-charge.

S&F GI tube 20 mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and as directed by Engineer-in-charge.

S&F rotational moulded polyethylene water storage tanks ISI Marked (cylindrical, vertical with closed top) of 500 Ltrs capacity hoisted and fixed in position all as specified and directed by Engineer-in-charge.

S&F rotational moulded polyethylene water storage tanks ISI Marked (cylindrical, vertical with closed top) of 1000 Ltrs capacity hoisted and fixed in position all as specified and directed by Engineer-in-charge.

Disconnecting existing tanks exc. 500 L and not exc.1000 L, setting aside (or lowering if required) for water tanks, dewatering, cleaning, sterilisation and removing all dirt, scale and algae formation from inside the tank by using lab tested cleaning chemicals including fixing stickers mentioning "TANK CLEANED ON" with date, month and year. The stages of cleaning process of tanks are as follows :- (a) To drain out the water by using exit valve or high capacity dewatering system. (b) Cleaning all the algae formation inside the tank by using TERBAC G5 / NB-10 / INCHLOR-5 lab tested branded chemical and scrubbing the walls of the tank by mechnised scrubber. (c) Fresh water cleaning by high speed jet pump. (d) Drying the tank then first stage of bacteria screening and sterilization of the tank by using TERBAC G5 / NB-10 / INCHLOR-5 lab tested branded chemical. (e) Cleaning the floor of the water tank by heavy duty industrial vacuum cleaner. (f) Second stage of bacteria screening and sterilization of the tank by using ultra violet ray ejector covering 360 degree within the tank and killing all suspended bacteria. (g) Third stage of bacteria screening and sterilization of the tank floor by using TERBAC G65 / NB-60 / INOXI-60 lab tested branded chemical. Note - (i) The quoted rate shall include for removal of mud, grits and deposits etc. properly from site of work and on completion of work sterilisation certificate to be submitted to the Engineer-in-charge. (ii) Cleaning needs to be done mechanically by authorised dealer/agent as approved by Enginner-in-charge. (iii) Cleaning chemical shall also be approved by Engineer-in-charge.

S&F in repair 20mm ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minium weight 20mm - 210 grams) and fixed in position complete all as per specified and as directed by Engineer-in-charge.

M&L for 15 mm thick screed bed or bedding layer of morter (1:6) for laying floor finishes complete all as specified and as directed by Engineer-in-charge.

M&L for 10mm thick screed bed or bedding layer of mortar (1:4) for vertical surface finishes, complete all as specified and as directed by Engineer-in-charge.

S&F coloured non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles complete all as per specified and as directed by Engineer-in-charge.

S&F coloured non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in vertical surfaces, etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles complete all as per specified and as directed by Engineer-in-charge.

M&L for Coloured Glazed ceramic tiles 200 x 300 x 6 or 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles complete all as per specified and as directed by Engineer-in-charge.

M&L for Coloured Glazed ceramic tiles 300 x 450 x 8 or 9 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles complete all as per specified and as directed by Engineer-in-charge.

Rounding to edges of stone slabs one edges such as in steps & other similar situation complete all as specified and as directed by Engineer-in-charge.

S&F in repair vitreous china ware wash hand basin white, flat back, size 550 x 400 mm size (flat back or angle back type) including cutting for and pinning ends of brackets or erecting stand and waste coupling of size 32 mm and waste pipe 32 mm, etc., complete all as per specified and as directed by Engineer-in-charge.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white, including seat cover, closed pattern with flat bottom and cover with chromium plated hinging device complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 15 mm bore CP basin mixer for mixing hot & cold water with capstin head screwed down high pressure with or with out littered 'H' or 'C' with long screwed shank and fly nuts screwed down for iron pipe, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) couple closet of size 360x680x765 mm, S trap - 220mm, white, including seat cover with chromium plated hinging device complete all as per specified and as directed by Engineer-in-charge.

S&F in repair kitchen plate rack made up of stainless steel and of minimum size 900 x 780 x 250 mm complete all as per specified and as directed by Engineer-in-charge.

S&F in repair Vitreous China squatting pan "Orissa" patern size 580x440mm white with integral foot rest including connection to trap and to flushing pipe, anti-syphonage pipe, etc including 'P' or 'S' trap complete all as per specified and as directed by Engineer-in-charge.

S&F in repair PVC 10 ltr capacity low level flushing cistern white with inlet ball valve float and braket and 32 mm bore PVC flush pipe, complete all as per specified and as directed by Engineer-in-charge.

M&L 40 mm thick cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) with integral WPC as in sunken floors, complete all as per specified and as directed by Engineer-in-charge. Note - WPC shall be measured and paid saparately.

M&L for mass concrete filling using PCC (1:5:10) type E2 in sunken floor using WPC @ 3% of cement used complete all as per specified and as directed by Engineer-in-charge. Note - WPC shall be measured and paid saparately.

S&F in repairs 32 mm High density polyethylene pipes (HDPE) of pressure rating 6 kgf/sqcm fixed to walls, ceilings or in floors etc. complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 15 mm bore brass CP wall mixer for mixing hot & cold water (Exposed Straight legs) with telephonic shower arrangement & Crutch (without hand shower and hoses) arrangement screwed down for iron pipe, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair chromium plated hand shower multi flow (ABS Body Chrome Plated with Gray Face Plate) with rubit cleaning system shower with CP flexible pipe up 15 mm bore with 1 m long Easy Flex tube in chrome finish, complete all as per specified and as directed by Engineer-in-charge.

S&F chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 15mm stop valves cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) for iron pipe or for unions complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 15mm angle stop valves cast copper alloy, fancy type with chromium plated for iron pipe or for unions complete all as per specified and as directed by Engineer-in-charge.

S&F in repair gun metal globe or gate valve, with iron wheel head screwed both ends for iron pipe of 15 mm bore complete all as specified and as directed by Engineer-in-charge.

Dismentling and breaking up 100mm/75 mm bore drain pipes AC /CI/PVC set in cement mortar complete all as per specified and as directed by Engineer-in-charge.

S&F 110 mm dia PVC (SWR) pipes single socketed, in any length, with rubber ring joints fixed to walls, complete all as per specified and as directed by Engineer-in-charge.

S&F of 150 mm internal diameter of double wall corrugated (DWC) high density polyethelene pipes (HDPE) and stiffness classes-8 (SN-8) with ISI marked (with CML no) with and including all fitting & jointing material for sewage line and laid in trenches as specified in IS 16098-2013 part-2 complete all as per specified and as directed by Engineer-in-charge.

S&F in repair PVC (SWR) 110 mm bore bends complete all as per specified and as directed by Engineer-in-charge.

S&F in repair PVC (SWR) 110 mm bore bends with access door complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 110 mm dia bore PVC (SWR) junction (single T) equal or un-equal, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 15mm dia PVC connection pipe with PTMT nuts of length 450mm complete all as specified and as directed by Engineer-in-charge.

S&F in repair fancy type 15mm dia bore pillar tap cast copper alloy with capston heads, chroumium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe complete all as per specified and as directed by Engineer-in-charge.

M&L rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, surface to be finished fair & even without using extra cement, complete all as specified and as directed by Engineer-in-charge.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:4), mixing with water proofing compound @2% by weight of cement consumed and surface finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge. Note- WPC shall be measured and paid separately.

M&L for G I Wire netting 0.9 mm dia and 12 mm mesh lathing to wood or metal studding, joists, etc., in walls, ceilings, stanchions, beams, etc., including all laps, cutting and waste, complete all as specified and as directed by Engineer-in-charge.

M&L rendering 10mm thick on other side of lathing in cement mortar 1:6, surface to be finished fair & even without using extra cement, complete all as specified and as directed by Engineer-in-charge.

M&L for rendering 15mm thick on other than fair faces of brick work or one side of lathing in cement mortar 1:4, surface finished even and smooth without using extra cement using water proofing compound in top layers as per manufacturer's direction, complete all as per specified and as directed by Engineer-in-charge. Note - WPC shall be measured and paid saparately.

Supply only integral water proofing compound confirming to IS complete all as per specified and as directed by Engineer-in-charge.

M&L 5mm thick ceiling plaster in CM (1:3) finished even and smooth without using extra cement complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated wood or wood based surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing surfaces of wood and wood based materials, new or old of any description and girth, not otherwise described and treated with two coats of cresote oil, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of cement based paint on walls over a coat of alkali resistant primer, complete all as per specified and as directed by Engineer-in-charge.

M&L applying two coats of distemper over a coat of 3 mm thick a layer of wall care putty on walls including preparation of surface complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by Engineer-in-charge.

M&L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed by Engineer-in-charge.

M&L 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in flooring/ hard standing/pavings/plinth protections, finished even and smooth without using extra cement complete all as per specified and as directed by Engineer-in-charge.

S&F in repairs 15 mm bore chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engineer-in-charge.

Supply and fix in repairs bib taps, standard of PTMT 15mm bore of any colour, high pressure, screwed for iron pipe complete all as specified and as directed by Engineer-in-charge.

S&F in repair brass chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges complete all as per specified and as directed by Engineer-in-charge.

S&F in repair cromimum plated health faucet shower with CP flexible pipe up 15 mm bore (ABS Body) with 1 m long Easy Flex tube in chrome finish, complete all as per specified and as directed by Engineer-in-charge.

S & F in repair jet spray nozzle with PVC tubing, fixing nut & jet flange complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 300mm dia ordinary rat tail rod pattern springs of mild steel including roller and roller plate for shutters complete all as per specified and as directed by Engineer-in-charge.

S&F in repairs, floor door stopper 14cm long of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor complete all as per specified and as directed by Engineer-in-charge.

S&F aluminium alloy 300 mm anodised sliding door bolts with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy, complete all as specified and as directed by Engineer-in-charge.

M&L in repairs aluminium door closer hydraulically regulated, designation No. 2, universal type, suitablefor door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as per specified and as directed by Engineer-in-charge.

M&L for petty repair to high or low level flushing cistern by adjusting the float valve leaking of PVC connection, PVC bend including replacing of rubber washer checks nuts plunger etc any type of flush complete all as per specified and as directed by Engineer-in-charge.

S&F in repair fancy type curtain/hanger rods of mild steel pre painted with fixing decorative bracket stops rollers etc complete all as per specified and as directed by Engineer-in-charge.

S&F in repair plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as per specified and as directed by Engineer-in-charge.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chomium plated bracket guard & railing 60 cm long, complete all as per specified and as directed by Engineer-in-charge.

S&F in repairs corner glass shelves with border to hold the bathing kit minimum width 150 mm and fixed in position complete all as per specified and as directed by Engineer-in-charge.

Supply and fix in repair 100mm dia grating doom of PTMT with minimum weight 25 grams complete all as specified and as directed by Engineer-in-charge.

Supply and fix in repair 125mm dia grating doom of PTMT with minimum weight 40 grams complete all as specified and as directed by Engineer-in-charge.

S&F in repair PTMT alloy single door cabinet with mirror of size 300 x 343 x 250 mm with inner shelves for holding bath/shaving kit complete all as specified and as directed by Engineer-in-charge.

S&F in repair 32 mm dia waste coupling of PTMT (half or full threaded) having minimum wt. of 45 grams complete all as specified and as directed by Engineer-in-charge.

S&F in repair sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915 mm x 460 bowl size 410 mm x 330 mm x 160 mm, complete all as per specified and as directed by Engineer-in-charge.

M&L for brick work with sub class 'B' bricks (old size), straight or curved on plan exc. 6m mean radius in cement mortar 1:4, complete all as per specified and as directed by Engineer-in-charge.

M&L for brick work with sub-class `B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-charge.

S&F in repair tank cover for PVC tank (500 / 750 / 1000Ltrs) cover with 6 mm dia MS bar hinging device and 6mm dia MS bar locking arrangement of 'S'- type for monkey protection etc complete all as per specified and as directed by Engineer-in-charge.

S&F in repair CP toilet paper roll holder with flap including all necessary fittings, complete all as per specified and as directed by Engineer-in-charge. Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.

M/s SHARMA BUILDERS & ENGINEERS

M/S Rajkamal Enterprise