SPECIAL REPAIRS TO CERTAIN TOILETS AND BATHROOMS IN AND OFFICER MESS COOK HOUSE P-85 AT AFAC COIMBATORE

Amount

Demolition of brickwork or stone boulder masonary , built in cement mortar complete all as specified and directed.

Demolition of reinforced cement concrete in ground floors and pavings n. exc 15 cm thick complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) to stone and rubbish off the premises complete all as specified and directed.

Demolition of concrete in ground floors and pavings n. exc 15 cm thick complete all as specified and directed.

Taking down cement plaster on brick or stone walls, ceilings, etc including racking out Joints, hacking for key, scrubbing down with water, etc

M&L brickwork with fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L brickwork with fly ash bricks straight or curved on plan exc 6m mean radius half brick thick walls, built in CM 1:4 complete all as specified and directed.

M&L reinforced cement concrete type B1 1:2:4 (using 20mm graded stone aggregate) as in slab supported on walls deck slab and in shelves etc complete all as specified and directed.

M&L TMT steel bars 10mm dia and over cut to length, bent to shape required, including cranking, bending sporally for hooping for slab, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L formwork to soffits of suspended slabs such as roof slabs, floor slab, landing and similar work not exc. 200mm thick complete all as specified and directed.

S&F rolled mild steel Fe 410-W (Grade E-250 quality A) as in Framed work as in doors or gates of angle or other section with gusset plates, rails, brackets etc, complete, drilled for fixing of steel sheeting or other covering, Doors, etc. to be prepared for hanging or sliding with and including either hooks door fittings (including rails and guides) and hanging also fastering and fixing complete all as specified and directed.

M&L for Cement concrete type B-1, 1:2:4 (20mm graded aggregate ) 40mm thick for sub base of floors complete all as specified and directed.

M&L for Screed bed or bedding layer of mortor 15 mm thick in CM 1:6 for laying floor finishes all as specified and directed.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces with CM 1:4 as in backing coat of skirting /dado all as specified and directed.

M & L for Non-skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed

All as per item No 16 above but as in skirting

M & L Glazed coloured ceramic tiles in vertical surface 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by Engr-in-charge..

M&L for Cement concrete type B-1, 1:2:4 (20 mm graded aggregate )in steps, coping water troughs and the like including weathering, slightly angles and throating all as specified and directed.

M&L 75mm thick cement concrete type C-2 , 1:3:6 (using 40mm graded stone aggregate as in plinth protection in alternative bay and surface finish even and smooth with out using extra cement complete all specified and directed.

M&L for Rendering in CM 1:6, 15 mm thick on fair faces of brick work or concrete surfaces all as specified and directed.

M&L for Rendering in CM 1:4, 15 mm thick on other than fair faces of brick work or concrete surfaces all as specified and directed.

M & L prepation of newly plastered wall surfaces and applying two coats of distemper oil emulsion over over a coat of primer over 2 to 3mm wall care putty all as specified and as directed directed by Engr-in-charge.

M & L for complete removal existing treatment of wall surfaces and applying two coats of distemper oil emulsion over a coat of primer over 2 to 3 mm wall care putty all as specified and as directed directed by Engr-in-charge.

M & L prepation of new plastered wall surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and as directed directed by Engr-in-charge.

M & L prepation of old wall surfaces and applying two coats of cement base paint complete all as specified and as directed directed by Engr-in-charge.

Preparation old surface of wood and wood based material of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed..

Preparation of new surface of wood and wood based material of any description not otherwise described over 10cm width or girth and applying one coat of pink primer and two coat of synthetic enamel paint.

Preparation of new surface of steel and steel based material of any description not otherwise described over 10cm width or girth applying one coat of red oxide zinc chrome and two coat synthetic enamel paint complete all as specified and directed.

Preparation old surface of steel and steel based material of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed..

Taking down chowkhats or frames with shutter (with out taking off the shutters from the frames) size exc 1.50 sqm and not exc 4.00 sqm each and all as specified and directed.

Taking down chowkhats or frames with shutter (with out taking off the shutters from the frames) size not exc 1.50 sqm each and all as specified and directed.

Taking down shutters of any description n exc 1.00 Sqm each each all as specified and directed.

S & F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, suplying and fixing in opening as per specification and drawing etc complete all as specified and as directed by Engineer- in-Charge.

S & F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tube for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck in side with solvent cement for stiles and plain colour PVC sheet for top rial, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement , suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed by Engineer-in-Charge.

S&F plain solid straight chowkhats with IInd class hardwood and frames wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed

Material and labour for 35 mm thick plain , framed panelled shutters with IInd class Hard wood (two panels), with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veeneering on both faces. The size of rail and stile as per IS 1003 (Part I), kiln seasoned and chemically pressure treated and fitted to chowkahts all as specified and as directed by Engineer-in-Charge.

Material and labour for 35 mm thick Glazed and skeleton shutter, open rebated and prepared to receive glass , gauge, etc with sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.24 (a) and fitted to chowkats complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers,plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel and all as specified and directed

S & F Floor door stopper 140mm long with cover plate of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apperture 1.40 mm and fixed with stainless steel wire staples all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of apperture 1.40 mm and fixed with stainless steel wire staples all as specified and directed.

S&F 150mm long Aluminium anodised barrel towers bolts of extruded section and all as specified and directed

S&F 125mm long Extruded aluminium alloy handles, fabricated type, anodised butt hinges, heavy weight, cold rolled mild steel and all as specified and directed

S&F 300mm long Aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy complete and all as specified and directed

S&F Mild steel rat tail rod pattern springs of size 300mm including roller and roller plate fixing to iron frame or wooden door by welding/ screwing including cutting out old damaged/inactive helical door spring all as directed.

S&F of 0.56 mm thick aluminium sheeting alloy 31000H4 fixed with doors and fixed by nails etc all as specified and as directed.

M& L 2nd claas hard wood plain fillets square/ rectangular or triangular in section, clean sawn secured with nails or brads sectional area exc 13 & not exc 25 sqcm.

S&F fancy type 19/20mm curtain rod ( Drapery rod) MS tubing with PVC colour coating and two No of colour PVC finials ( Latto) with brackets and min 8 to 10 Nos PVC curtain hooks for each window/ door and complete fixing arrangements complete all as spd and directed.including taking down existing curtain rod/ palmate box of any description and any position etc all as specified and directed.

M & L for Granite (Lakha red / Kharde red /Rubby red ) 18 mm to 20mm thick machine cut,(of any type work (table rubbed and polished) as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone complete and as directed.

Providing Rounding to edges of stone slabs one edge,such as in steps, cooking platform, and other similar situations

M & L natural stone slab (Moon white/pearl white/sahara white)18 mm to 20mm thick machine cut,(of any type work (table rubbed and polished) as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. bedded and jointed with gray cement slurry and pointed with white cement withadmixture of pigment to match the shade of granite stone complete and as directed.

M &L for pointing and jointed with grey cement slurry or white cement and with admixture of pigment to match the shade of polishing on marble/ granite/Kota stone/ stone work where ever required to give high gloss finish complete including grinding and polishing complete

M&L for Machine cut Kota stone 18 to 20mm thick as in floors, , laid over 15mm thick rendering in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing (granite finish) including cutting hole for inserting of studs, moulding and nosing as required etc complete as per specification and as directed by Engr-in-charge.

M & L for 18/19mm thick prelaminated particle board , exterior grade , prelaminated both side with decorative choice laminarion and and fixed with screw to frame etc complete all as specified and as diirected.

S&F Continous (piano) hinges 30mm width mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F 100 mm long Hasp and staple, aluminium anodised, inclufing bolt to hinge plate and fixed with screw complete all as specified and directed.

Taking up or down steel tubing and connections, and removing to store for taking in account of credit for 15mm bore complete all as specified and directed.

All as per item No.59 above but for 20 mm bore

S&F 15mm bore steel tube medium grade galvanised, with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

All as per item No.61 above but for 20 mm bore

S& F in repair Vitreous China wash basin, white, flat back, size 630x450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specifed and directed.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white including seat cover and flush pipe etc complete all as per specified and as directed by Engineer-in-Charge.

M & L for PVC (SWR) multi floor trap of 75mm dia with grating including jointing with solvent cement etc complete,

M & L for PVC (SWR) gully trap of 125/110mm dia includingsetting jointing with solvent cement etc complete,

S & F PVC (SWR) pipe 110mm dia single sockted in any length with rubber ring joints fixed to wall complete all as specified and directed.

All as per item No.67 Above but for 75 mm bore

S & F in repair Unplasticised PVC pipe 50mm dia of pressure rating 10 kgf /cm2 fixed complete to walls, ceiling or in floors etc complete

S&F PVC (SWR) bends 110mm radius complete all as specified and directed.

M&L UPVC pipe of pressure 10 kgf/cm 2 suitable for water supply distribution incl all fittings,25 mm dia

M&L UPVC pipe of pressure 10 kgf/cm 2 suitable for water supply distribution incl all fittings,20 mm dia

M&L UPVC pipe of pressure 10 kgf/cm 2 suitable for water supply distribution incl all fittings, 15 mm dia

Supplying and laying of CPVC pipes 20mm dia bore SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specifies

S & F in repairs PVC valveless, syphonic action type, flushing cistern of 10 Ltrs capacity , low level , white, with inlet , ball valve, float and handle including brackets and flush pipe etc complete all as specified and as direted by Engineer-in-Charge.

S & F PVC connections 15 mm size with PTMT nuts of length 450 mm

S& F in repairs PVC waste pipe 32mm bore for ,WHB,and Sink

S & F in repairs towel rail 60cm long of brass chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 190 gms).

S&F in repairs Bib taps, brass chromium plated fancy type with cruch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore.

S&F in repairs chromium plated angle valves, cast copper alloy, screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipes or for unions and fixed. 15 mm size.

S&F in repairs chromium plated stop cock, fancy type with long shank and cup (Concelled type )cast copper alloy, screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipes or for unions and fixed. 15 mm size.

S&F in repairs Pillar taps fancy type cast copper alloy, with capstain head, chromium plated screwed down high pressure, with long shanks and fly nuts screwed for iron pipe and fixed 15 mm bore.

S&F in repairs brass chromium plated health faucet with hand held and spring operated control valve with PVC flexible pipe connection of suitable length as directed fixed to 15 mm bore pipe.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen with plugs, waqshers and wastes, including bedding in cement mortar on to dward wall or including fixing cantilever brackets and connection union to pipe, overall size 915X460mm bowl size 410mmX330mmX160mm complete all as specified and directed.

S&F in repairs double bowl delux sinks gloss finish with out drainage board made of 1mm thick stainless steel 304 grade kitchen with plugs, wahers and wastes, including bedding in cement mortar on to dward wall or including fixing cantilever brackets and connection union to pipe, overall size 1155x515mm ( instalation top mount) Depth 250mm complete all as specified and directed.

Dismantling of PVC water tank 500 ltr capacity and removing to store

S&F moulded polyethylene 500 ltr water tank storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Eng5r-in-charge.

S&F moulded polyethylene 1000 ltr water tank storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Eng5r-in-charge.

S&F in repairs 20 mm Ball brass valves, high pressure, with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed in repairs complete all as specified and directed.

S&F in repairs 15mm bore Gun-metal , globe or gate valve, with iron wheel head, screwed both ends for iron pipe fixed complete all as specified and directed.

S&F in repairs 20mm bore Gun-metal , globe or gate valve, with iron wheel head, screwed both ends for iron pipe fixed complete all as specified and directed.

S & F in repair stainless steel wall mounted plate rack of size 900x750x260mm of approved make complete all as specified and directed.Make : M/s Blue Star , Model No: BSKPR-311 or other equvalent make as approved by Engr -In-Charge

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staple complete all as specified and directed.

M&L framed work such as grills ,grating etc with ends of bars shouldered or riveted, or forged into spikes conforming to Fe 290-Gde -E-165.

M&L at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

M&L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall using chemical emulsion at the rate of 2.25 liters per linear meter including drilling and plugging holes etc. in apron complete all as specified and directed.

M&L for treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as specified and directed.

Removal of debries /building material out side the campus including loading and unloading , etc to a distance exc 5.00 Km but n. exc 10.00 Km out side the MoD land all as specified. Note: Location and premission of depositing the building materials/disposal out side the M of D land shall rest with contractor at his own arrangement.

M&L for Fabrication & fitting of modular kitchen with cabinet & wardrobe/ cupboard made out of 18 mm thick PVC board plain sheet including providing cabinet for keeping baskets/ cutlery basket with handles complete.Make : Rajshree or equivalent all as specified and approved by Accepting Officer Note: Modular Kit accessories ie baskets, cutlery baskets, fittings and fixture will be measured and paid separately as supply only

Supply only stainless steel acessories suitable for kitchen cabinets as under:-

(a) Stainless steel basket (plain) of size 50cmx37cmx10cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No WA/POB/15204 or equivalent approved

(b) Stainless steel thali basket (11-13 division) of size 50cmx37cmx20cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No WA/TB/15208 or equivalent approved

(c) Stainless steel Plate basket (11-13 division) of size 50cmx37cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No WA/PTH/15206 or equivalent approved

(d) Stainless steel Partition basket of size 50cmx37cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No WA/PRT/17206 or equivalent approved

(e) Stainless steel Cutlary basket of size 50cmx37cmx10cm made of 4mm th S.S.wire and bottom of S S perforated sheet approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No WA/CUT/15204 or equivalent approved

(f) Stainless steel basket (plain) of size 50cmx37cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No WA/POB/15206 or equivalent approved

(g) Stainless steel bottol full out of size 50cmx40cmx16cm in two tier made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No FF/BPO/62018 or equivalent approved

(h) Stainless steel basket (plain) of size 50cmx52cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No WA/POB/21206 or equivalent approved

(i) Stainless steel grid basket (plain) of size 50cmx52cmx20cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No WA/POB/21208 or equivalent approved

(j) Telescope basket (channel) 18'/20' length extruded MS galvanised over rollers of approved make

(k) Door closer magnet of approved quality

(l) Autocut Hydrolic stainless steel hinges

(m) 150 mm dia oval shape brass handle fancy type polished bright finish

(o) Continuous (Piano) hinges, brass, 30 mm width of flaps (when open).

Excavation in trenches n. exc 1.5 m wide and n. exc 1.5 m depth and getting out in Hard dense soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick using soil obtained from excavation complete all as specified and directed.

Removing excavated soil to a distance not exc 50 metre and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed. .

M&L for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in bed for manhole complete all as specified and directed.

M&L for Plain cement concrete 1:4:8 type C2 (using 40 mm graded stone aggregate) for concrete bed to drain pipes (work in foul condition) including packing under and hunching against the sides of pipes after they are laid and tested for 150 mm dia pipes complete all as specified and directed.

M&L for PCC 1:3:6, type C1 (using 20 mm graded stone aggregate) for coping and benching inside the manholes including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L for Precast cement concrete 1:2:4, type B1 (using 20 mm graded stone aggregate) as in cover slab for manholes set in cement mortar 1:6 complete all as specified and directed. Note: Reinforcement will be measured and paid separately (use and waste of form work is deemed to be included).

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick wall surfaces, finished even and smooth using extra cement complete all as specified and directed. .

S&F PVC SWR pipes, 150 mm bore, single socketed in any length with rubber rings joints, laid in trenches complete all as specified and directed.

M&L for extra form farming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms moulds ,mitred stopped ends etc.

Taking down shutters of any description exc 1.00 Sqm but not exc. 2 Sqm each all as specified and directed.

S & F Unplasticised PVC pipe 50mm dia of pressure rating 10 kgf /cm2 fixed complete to walls, ceiling or in floors etc complete

S&F PVC (SWR) pipes single sockted in any length with rubber ring joints laid fixed to walls 150 mm bore as in rain water pipe

S &F PVC (SWR) branch piece,110mm bore double (double Y) equal or unequal

S &F PVC (SWR) branch piece,110mm bore single (single Y) equal or unequal

S &F PVC (SWR) branch piece,75mm bore double (double Y) equal or unequal any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends any radius 110 mm bore any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends any radius 75 mm bore any radius with access door complete all as specified and directed.

S&F of PVC (SWR) vent Cowl 110 mm bore

S&F of PVC (SWR) vent Cowl 75 mm bore

S&F 32mm brass CP waste coupling to WHB

S&F in repairs 125mm dia shower rose brass chromium plated with or without seivel joints, including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe)

M & L for preparation of old treated surfaces and applying two coats of white wash on ceiling.surface all as specified.

M & L for preparation of old treated wall surfaces and applying two coats of white wash all as specified.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated brackets guard and raling 60 cm long complete all as specified and directed

S& F Glass corner shelf of size 30x30 cm with heavy wall brackets and fixed to walls complete all as specified and directed.

S&F sheet glass, ordinary quality 5.5mm thick and glazing with aluminum beading or gasket in square/rectangular exc 0.5sqm in each panes complete all as specified.

Taking down old unserviceable point wiring (light, fan socket or power) complete, including fixture and fittings such as switches,ceiling rose, pendents, regulators,sockets, light fittings etc.removing materials for keeping for taking credit( credit for above items should be made as per conditions separately) and making good disturbed surface of walls floors etc. all as specified.

Taking down old unserviceable submain wiring of any size including GI/copper earth continuity conductor in PVC conduit on wall/roof and making good to disturbed surfaces all as directed.

Taking down exhaust fan, sealing cable end, dismantling blades from fan and keeping in safe custody for reuse at site and making good disturbed surfaces complete all as specified and as directed.

Taking down Ceiling fan sealing cable end, dismantling blades from fan and keeping in safe custody for reuse at site and making good disturbed surfaces complete all as specified and as directed.

Refixing only Ceiling fan with and including carrying out cleaning servicing, oiling and greasing of ceiling fans and connecting up including provision of cable from celling rose/ connector to fan all as specified and as directed.

M& L painting of Ceiling fan complete, in situ with synthetic enamal paint by spraying incl filling cavities with filler, one coat after cleaning all dust etc all as specified and as directed.

Refixing only exhaust fan ( In Repair) and connecting up including provision of cable from celling rose/ connector to fan all as specified and as directed.

M& L for painting of exhaust fan complete, in situ with synthetic enamal paint by spraying incl filling cavities with filler, one coat after cleaning all dust etc all as specified and as directed.

Disconnecting electric connection and taking down main switch/DB of any size and keep in safe custody for taking credit complete and good/levelling the disturbed surfaces of wall to match with existing surface.

Supply and fixing Metal clad single pole and earth enclosure with three pin and earth plug with socket complete with one single pole MCB 20 amp including all as specified. Make: L&T/Legrand/ Havells

M&L for concealed Point wiring complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistranded copper conductor drawn through in and including 20mm dia PVC rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling/roof/etc including 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed for the following :- (a) One light point controlled by one, one way switch.

(b) One ceiling/exhaust fan point controlled by one, one way switch.

(c) One switch socket outlet point 5 Amps on independent board.

(d) One 05 Amps socket outlet point on same board.

All as per item No.10 described here-in-before but with copper conductor cable FRLS, 4.00 Sqmm for one 3 pin socket outlet, 15 Amps and including 2.5 Sqmm PVC insulated copper conductor cable as earth continuity conductor on independent board.

M&L for concealed point wiring complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistranded copper conductor drawn through and including 20mm dia PVC rigid non metallic conduit with all accessories such as internal bend end caps etc complete including pressed steel sunken boxes 2 mm thick concealed in walls including 3 mm thick phenolic laminated sheet cover and including 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor connected with dolly, all as specified and as directed for the following :- Note: ( Cutting chases and making good in wall / floor will be Measured and paid seperately.

One light point controlled by one, one way switch.

One exhaust fan point controlled by one, one way switch.

One 05 Amps socket outlet point on same board.

One 05 Amps socket outlet point on independent board.

All as per item No. 1 described here-in-before but with copper conductor cable FRLS, 2.5 Sqmm for one 3 pin socket outlet, 15 Amps and including 2.5 Sqmm PVC insulated copper conductor cable as earth continuity conductor on independent board.

Note for item No. 11 & 21 : Cutting chases and making good in wall / floor will be Measured and paid seperately.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.Make-Havells/Bajaj/Crompton

Supply & fix universal regal LED batten 1x20/22 watt surface mounting tube light fitting complete and making connection complete. Make: Havells Cat No. REGALBATTENT8UPTO1x22WSSBSWH with LED Tube rod Havells Cat No. CRYSTALT 81213SSTL20WLED865SGLASS or equivelent in crompton/ C&S

Supply and fix building security light 30 Watt, new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening separate driver compartment with IP65 protection and impact resistance of IK07 complete with and including GI bracket made of suitable size medeium grade GI pipe bent to shape and fixed complete all as specified. Make: Havells Cat Part No - LHEXAYP7PN6K030/Bajaj/ Crompton Greaves.

Supply and fix building security light 35 Watt, new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening separate driver compartment with IP66 protection and impact resistance of IK08 complete including fixing bracket of suitable size . Make: Havells Cat No.ENDURASUNDOWNSL35WLED765PASYBOPC ,or Equivelent in Philips, Crompton.

Supply and fix sheet metal enclosure with distribution board (DB) TPN, 415 volts, having IP:43 protection, isolated neutral bar, insulated busbar assembly, door earthing arrangement, mechanical impact strength IK08, 06 way compact double door suitable for fixing MCBs TPN as in commer and out going complete . Make: L&T/Legrand/ Havells

Supply and fix MCB DB, SPN, 4 ways, Isolated neutral bar, IP54 protection, doubel door earthing arrangement with cement spill protector, mechanical impact strength IK09 complete.

Supply and fix MCB DB, SPN, 8 ways, Isolated neutral bar with single door IP54 protection, door earthing arrangement with cement spill protector, mechanical impact strength IK09 complete. Make: L&T/Legrand/ Havells

Supply and fix MCB DB, SPN, 4 ways, Isolated neutral bar with single door IP54 protection, door earthing arrangement with cement spill protector, mechanical impact strength IK09 complete. Make: L&T/Legrand/ Havells

Supply and fix MCB TPN 63 Amps, 240Volts, 10 KA, "B" Curve complete. Make: L&T/Legrand/ Havells.

Supply and fix MCB TP 63 Amps, 240Volts, 10 KA, "C" Curve complete. Make: L&T/Legrand/ Havells.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fix MCB SPN 20 Amps, 240Volts, 10 KA, "B" Curve complete. Make: L&T/Legrand/ Havells

Supply and fix MCB SP 6 to 32 Amps, 240Volts, 10 KA, "B" Curve complete. Make: L&T/Legrand/ Havells

Supply and fix ceiling rose surface type bakelite 65 x 50mm with three terminals.

S&F Modular fan regulator step type 120 W, 2 module complete all as specified and as directed.

S&F Switch Modular 6A single pole, one way, 1 module complete all as specified and as directed.

S&F Switch Modular 16A single pole, one way, 1 module complete all as specified and as directed.

S&F Socket, 6A - 2/3 pin combined 2 module complete all as specified and as directed.

S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed.

S&F Switch piano, flush type single pole, one way 05 Amps complete all as specified and as directed.

S&F Switch piano, flush type single pole, one way 15 Amps complete all as specified and as directed.

S&F Socket outlet 3/5 pin, 06 Amps, flush type complete all as specified and as directed.

S&F multi socket outlet , 2 in 1, 3 pin, 16 Amps, flush type complete all as specified and as directed.

M&L for concealed Sub main wiring by making recess in wall/surface complete with 2 runs of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories suface/concealed in wall/Ceiling etc for three phase sockets all as specified and as directed by engr - in- charge. Note :- 2 runs of 4 sqmm, + 1 run of 4 sqmm (Earth Cotinuity conductor) and 1 run of PVC conduit shall be measured as one unit length.

M&L for concealed Sub main wiring by making recess in wall/surface complete with 2 runs of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories suface/concealed in wall/Ceiling etc for three phase sockets all as specified and as directed by engr - in- charge. Note :- 2 runs of 6 sqmm, + 1 run of 6 sqmm (Earth Cotinuity conductor) and 1 run of PVC conduit shall be measured as one unit length.

M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 M below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt , earth lead GI wire 4mm dia ( 8 SWG) connectd to GI earth plate elcectrode by means of bolts, nuts, check nuts, washers of galvanised iron, thimbles and other end of earth wire connected to main switch board/ feedar pillar and protected by galvanised iron pipe medium grade 15mm bore and 20mm bore medium grade GI pipe with funnel and wire mesh for watering including necessary excavation and earth works. PCC Chamber in cement concrete 1:2:4 type B-1 & RCC cover and all as shown in Electrical Plate No. 3 of SSR ( Part-I) of 2009. (i) The unit rate includes earthing wire, and protection pipe upto 7.5 metre.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth

Supply and fix sheet metal enclosure with distribution board vertical (DB) VTPN, 415 volts, having IP:43 protection, isolated neutral bar, insulated busbar assembly, door earthing arrangement, mechanical impact strength IK08, 8 way double door suitable for fixing MCCB160 Amps as incommer and TP/SP as out going complete, fixed on wall and connecting with all electric connections/circuit complete all as directed by Engineer in charge. Make: L&T/Legrand/ Havells.

Supply and fix MCCB 4 pole, 36 KA, 415 V, , adjustable thermal setting, 160 Amps complete. Make: L&T/Legrand/ Havells.

M&L for 4 mm dia galvanised iron or steel wire as earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc as required complete.

Taking down old serviceable underground cable of size 70 sqmm 3.5 core and refixing using aluminium clips as required in GI pipe on wall/roof and making good to disturbed surfaces all as directed.

M&L for GI pipe 50 mm dia light grade with all fittings for cable protection laid under road/path/hard standing or fixed with wall/pole etc complete.

UNIQUE INDIA CONSTRUCTIONS

p.chinnasamy