construction of rigid pavement to SH 179 to (old stand Gargoti (K.T.weir) Akurde road V.R. No-37 CH-0/0-0/380 TAL-Bhudargad, Dist-Kolhapur.

Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 metre and spreading for embankment or stacking as directed. By Mechanical Means. Item / Page No : 11 / 23 Specification No : MORTH-301 Spec. Page No : 45-53

Providing soling using 80 milimetre size trap metal in 15 centimetre layer including filling voids with crushed sand / grit, ramming, watering, excetra complete. Item / Page No : 40 / 157 Additional Specifications : The work shall be carried out as per instructions of Engineer in-charge.

Providing and laying Cast in situ/Ready Mix, cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailling out water, formwork, laying/ pumping, compacting and curing, excetra complete, with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Aquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) excetra complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed, excetra) Item / Page No : 1 / 175 Specification No : Bd.E.1 Spec. Page No : 287 - 288 Additional Specifications : 1. With additional specifications for controlled concrete. 2. If artificial / VSI crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in Circular by Chief Engineer, Public Works Region, Pune bearing No CEP/D-2/Buildings-2/5940/2017 dated 17/10/2017 and Annexure-I attached to it and also Circular by Chief Engineer, Public Works Region, Nagpur bearing No 36 dated 15/01/2019 and Annexure-I attached to it will be appicable.

Providing and laying in situ cement concrete M-30 with tremix treatment for 200 milimetre thickness for concrete road including laying plastic sheet of 125 micron thickness with groove cutting of 4 milimetre wide and 20 milimetre deep with necessary refilling with bitumen (excluding reinforcement) with coarse and fine aggregate (V.S.I. grade finely washed crushed sand) excetra complete. Item / Page No : 22 / 44 Specification No : MORTH 602 Spec. Page No : --- Additional Specifications : 1. The work shall be carried out as per instructions of Engineer in charge. 2. If artificial / VSI crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in Circular by Chief Engineer, Public Works Region, Pune bearing No CEP/D-2/Buildings-2/5940/2017 dated 17/10/2017 and Annexure-I attached to it and also Circular by Chief Engineer, Public Works Region, Nagpur bearing No 36 dated 15/01/2019 and Annexure-I attached to it will be appicable.

Supplying trap metal of required size by bringing the boulders / rubble at the road side breaking them to required gradation including conveying the boulders / rubble and stacking the broken metal, excetra complete. (Prior approval of sample stack of broken metal by the Executive Engineer is necessary the date of approval will form part of the measurements) - 40 milimetre metal, by breaking rubble obtained by blasting. (Hand broken). Item / Page No : 55 / 345 Additional Specifications : 1. Work shall be carried out as per the instructions of Engineer In-Charge. 2. Prior approval of sample stack of broken metal by the Executive Engineer is necessary. The date of approval will form part of the measurements.

Supplying soft murum at the road site, including conveying and stacking, excetra complete. Item / Page No : 29b / 25 Specification No : MORTH-408 Spec. Page No : 139-142

Spreading 80 milimetre / 40 milimetre metal for road work including sectionong, excetra complete as directed by Engineer in charge. Item / Page No : 58 / 346 Additional Specifications : Work shall be carried out as per the instructions of Engineer In-Charge.

Spreading hard murum / soft murrum / gravel or kankar for side width, excetra complete. Item / Page No : 30 / 25 Specification No : MORTH-408 Spec. Page No : 139-142

Compacting the sub grade / gravel / size metal (100 milimetre loose) layers for all widths with Power roller having weight 8 to 10 MT. including necessary, labour, materials and artificial watering complete. Item / Page No : 61 / 346 Additional Specifications : Work shall be carried out as per the instructions of Engineer In-Charge.

Providing and constructing 75 milimetre thick modified penetration macadam road surface including all materials, preparing the existing road surface, spreading 40 milimetre stone metal layers 30 percent crusher broken metal plus 70 percent hand broken (by breaking rubble obtained by blasting), heating and spraying the bitumen of of specified grade at the rate of 2 kilogram per square metre, spreading 12 milimetre size chips, compacting with three wheel static roller having weight 8 to 10 metric tonnes to achive the desired degree of compaction as per technical specification Clause 506, excetra complete. Including picking of existing water bound macadam surface. (Using VG-30 bulk bitumen) Item / Page No : 35a / 31 Specification No : IRC-SP-20 Spec. Page No : 215

Providing and Laying open graded premix surfacing of 20 milimetre thickness composed of 13.2 milimetre to 5.6 milimetre aggregates premixed with bituminous binder, transported to site with vehicle tracking system, laid over a previously prepared surface, finished to the required grade, level, alignment, and rolling to achieve the desired compaction, excluding prime / tack coat and seal coat. For Bitumen VG-30 bulk (Grade 60/70) - Using drum mix type hot mix plant with Supervisory Control and Data Acquisition, Paver and vibratory roller. (Over modified penetration macadam surface) Item / Page No : 12 / 36 Specification No : MORTH-501, 510, 511, 902, 903, 112 Spec. Page No : 149-162, 198-205, 205-207, 417-421, 421-436, 19-21

Providing and applying tack coat on the prepared surface, heating by flames in boiler and spraying bitumen with sprayer. On dry / hungry black topped surface at the rate of 3.0 killogram per 10 square metre. (Using VG-30 bulk bitumen) Item / Page No : 31 / 30 Specification No : MORTH-503 Spec. Page No : 168-170

Providing bituminous type-A liquid seal coat on bituminous surface including supplying all materials and bitumen of VG-30 grade, preparing existing road surface, heating and applying bitumen at the rate of 0.98 kilogram per square metre by mechanical means, spreading chips and rolling by static roller having weight 8 to 10 metric tonne, excetra complete. Item / Page No : 1 / 35 Specification No : MORTH-511 Spec. Page No : 149-162, 205-207, 198-205, 417-421, 19-21

Providing and fixing reinforcement cement concrete 200 metre stones as per Indian Road Congress standard including fixing in standard size cement concrete 1:4:8 block including curing, painting, lettering, excetra completed. Item / Page No : 2a / 46 Specification No : MORTH-807 Spec. Page No : ---

Painting Line, Dashes, Arrows etc on Roads in two coats on new work with ready mixed road marking paint confirming to Indian Standard 164 on Bituminous surface including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control Upto 10 centimetre Wide On New Surface Item / Page No : 8b / 46 Specification No : MORTH-202 Spec. Page No : 39-42

Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and Abstrone Butadyne Styrine moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kilogram tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of Ministry of Road Transport and Highways Circular number RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 milimetre, 100 milimetre and 102 +/- 2 milimetre and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 milimetre and height not less than 30+/- 2 milimetre) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retroreflectance of the reflecting panel, to the Engineer Item / Page No : 9 / 47 Specification No : MORTH-202 Spec. Page No : 39-42

Goods and Services Tax @ 18% Item / Page No : 15 / 0 Additional Specifications : The work shall be carried out as per the instructions of Engineer in-charge.

Add insurance towards labour @0.50% Non-Dsr Item Additional Specifications : The work shall be carried out as per the instructions of Engineer in-charge.

Please Enable Macros to View BoQ information