PMN/NIT/88/25-26/PMZP/PM

Figure

Dressing and Chilchelling Roaf flanks including cutting and filling with earth upto 150mm thickness finished with outward cross grade of 1 in 30 (Extra quantity of earth for filling shal be obtained from road side borrow pits.)

Earthwork in excavation from borrow pits (land owned/arranged by the Department) and depositing in layers of 250 mm. including breaking clods in embankment works and to fill up back of abutments, depressions and ruts with an initial lead up to 50 m and initial lift up to 1.5 m making bunds at top as directed dressing complete. (Borrow pit measurement) (i) In ordinary soil

(Lead upto 500 M.)

Water Bound Macadam Sub Base. Water Bound Macadam Sub Base by consolidating Jhama metal / Laterite chelly or stone metal / shingles of specific size in hard crust to requisite thickness (measured after compaction) in layers including screening of metals etc. as necessary, hand packing, sweeping, watering and rolling in stages with power roller to proper line, grade and camber, lighting, guarding & barricading and making necessary earthen bundh of one metre width on each side where necessary to protect edges and preparing the bed by necessary cutting or filling and rolling all complete including the cost of all materials and hire and labour charges of all men and machineries and compacting to the required density, as per Clause 404 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). (i) For Construction of Sub Base by consolidating Jhama metal (63 mm to 45 mm) with moorum screening :

Construction of un-reinforced, plain jointed, plain cement concrete pavement over a prepared sub-base with cement, course and fine aggregate conforming to IS : 383 with nominal mix of (1 : 1.5 : 3) concrete, maximum size of course aggregate not exceeding 25 mm., mixed in a place method using concrete mixer and laid in panel as per approved design not exceeding 2.5 m. x 2.5 m. panel size including form work, spreading, compacting and finishing in a continuous operation including provision of contraction, expansion, construction and longitudinal joint as applicable with bitumen joint filler, separation membrane and dowel bar as approved including curing and finishing to lines and grades complete in all respect as per approval of Engineer-in-Charge.

Supplying and laying polythene sheet (150 gm./sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches.

Protective work (Ballah Pilling )Supplying 150 mm dia EUC bullah 4.0 Mtr long & driving 2/3 of length @ 375 mm C/C , Supplying 150 Cm dia tie post 2.5 M long and driving 2.35 M @ 1.8 M C/C and suppling fitting Fixing 12.5 Cm dia tie bars @ 1.8 m C/C , 10 cm dia runners in 3 rows. Suppling gunny bags , filling the same with earth and placing inside the pilling.

Supplying best and approved quality moorum stack at site For Hard Shoulder

Bituminous filler of approved type in expansion joints of dummy joints including finishing the top surface as directed.

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and hick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In- Charge.

Estimated Cost

TOTAL

Total

Sub-Assistant Engineer Purba Medinipur Zilla Parishad

Executive Engineer, ( P.& R.D. ) & District Engineer-in-Charge Purba Medinipur Zilla Parishad

Name of the work :

Figure

Main Table with ERU Model – COEVAL Size in mm – MD: 2100 X 900 X 750 & ERU: 1500 X 550 X 750. MAIN TOP PANEL: Made of 36mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. SIDE PANEL: Made of 36mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. MODESTY: Modesty is made of painted 8mm thick toughened glass (as per IS:2835) fixed on a metal frame made of stainless steel tubes, Grade 304 of cross section 19×19×2 thick and 3mm thick stainless steel plates with the help of both side adhesive tape. COEVAL METAL PLATE: Coeval metal plate is made of 8mm thick Stainless Steel GRADE 304. It is fixed between the main top panel and side panel on both sides of the desk. RETURN TOP: Made of 36mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. TABLE SIDE PANEL: Made of 36mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. UNDER STRUCTURE PANEL: Made of 18mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. CPU bottom panel in case of 700D return unit is provided with castor at the bottom for ease of opening and closing CPU portion. DRAWER PANEL: Made of 18mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. Drawers are provided with push open mechanism and side central lock. PEDESTAL TOP PANEL: Made of 36mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. SIDE PANEL: Made of 18mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. DRAWER PANELS: Made of 18mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. Drawers are provided with push open mechanism and side central lock.

High Back Chair (Leatherette) Model – Sapphire 1. SEAT WITH ARMREST ASSEMBLY: The seat with armrest assembly is a combination of upholstered seat and upholstered loose seat cushion. The seat with armrest is made up of 15mm thick moulded plywood layered with density of 60 kg/m³ slab stock foam and a 200 GSM recron sheet is placed at both armrest ends. Sub-assembly is then upholstered with seat cover. Loose cushion is made of super soft foam of 32 kg/m³ density layered with 28 kg/m³ density of foam on both sides and a 200 GSM recron sheet is placed over the foam assembly and sub assembly is then upholstered with loose seat cushion cover. 2. BACK ASSEMBLY: The back assembly is made up of 12mm thick moulded plywood layered with P.U foam of 45 kg/m³ density and U-foam of 28 kg/m³ density. A 200 GSM recron sheet is placed over the P.U foam and whole sub-assembly is upholstered with leatherette cover. 4. CENTER TILT WITH MULTI POSITION LOCK MECHANISM: The mechanism is designed with the following Features:• 360° revolving type• 3 position locking• Tilt tension adjustment 5. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has a stroke of 10.0 ± 0.3 cm. 6. PEDESTAL ASSEMBLY: The pedestal is made of high-pressure die-cast polished aluminum. It is fitted with 5 castors and has a pitch-center diameter of 65.5 ± 0.5 cm. 7. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black polyamide. Width: 84.0 cm , Depth: 80.0 cm , Height: 102.5 – 112.5 cm , Seat height: 45.0 – 55.0 cm

Visitor Chair Model – 7044T (FABRIC) 1. SEAT/BACK ASSEMBLY: The seat is made from 1.2 ± 0.1 cm thick upholstered plywood measured as per QA and back should be injection moulded from black Co-polymer Polypropylene upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam should be designed with contoured lumbar support for extra comfort. SEAT SIZE: 45.0 cm (W) × 42.0 cm (D) BACK SIZE: 39.0 cm (W) × 38.0 cm (H) 2. SEAT/BACK COVERS: The seat and back covers should be injection moulded in black Co-polymer Polypropylene. 3. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density = 45 ± 2 kg/m³ and hardness load 16 ± 2 kgf for 25% compression. 4. ARMREST ASSEMBLY (FOR 704T): The armrests should be of black integral skin Polyurethane with 50–70 Shore ‘A’ hardness and reinforced with M.S. insert. The P.U. armrests should be then fixed to black powder-coated (OFT 40–60 microns) armrest brackets made of 0.5 ± 0.05 cm thick HR steel with claddings made of injection moulded Polypropylene. 5. FIXED TYPE MECHANISM: The fixed type mechanism should be without back tilt. 6. TUBULAR FRAME: The tubular frame should be made up of 2.54 ± 0.03 cm × 0.2 ± 0.016 cm thick M.S. E.R.W. tube and black powder coated (DFT 40–60 microns).

Back Unit Model – COEVAL (Tall Flap Up Storage) Size in mm: 1200 W × 520 D × 1850 H Made of 36mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. SIDE PANEL: Made of 18mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. OVERHEAD STORAGE PANELS: Made of 18mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. BOTTOM PANEL: Made of 36mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. BACK PANELS AND UNDERSTRUCTURE PANELS: Made of 18mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides.

Back Unit Model – COEVAL (Back Unit – Tall Display Unit Storage) Size in mm: 1200 W × 520 D × 1850 H TOP PANEL: Made of 36mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. SIDE PANEL: Made of 18mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. DISPLAY SHELF PANELS: Made of 36mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. BOTTOM PANEL: Made of 36mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides. BACK PANELS AND UNDERSTRUCTURE PANELS: Made of 18mm thk medium density fibre board as per IS:12406 with pigmented polyurethane coating on both sides.

Total

Rupees Seven Lakhs Nine Thousand Three Hundred Forty Six Only

Sub-Assistant Engineer Purba Medinipur Zilla Parishad

District Engineer Purba Medinipur Zilla Parishad

Purba Medinipur Zilla Parishad

NIT No.- of 2025-2026, Sl No. -

ABSTRACT COST FOR THE PROJECT

ITEM OF WORKS

TOTAL :

Add : GST @ 18.00%

TOTAL :

Add : Cess @ 1.00%

TOTAL TENDER AMOUNT FOR THE PROJECT :

Rupees Eight Lakhs Seventy Five Thousand Nine Hundred Twenty Three Only

District Engineer

Purba Medinipur Zilla Parishad

Percentage BoQ

BoQ_Ver3.0

Bidder Name :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Supplying, fitting and fixing of Various Furnitures at Administrative Building in the district of Purba Medinipur.