SPECIAL REPAIRS TO OFFICER MD ACCN QTR P 5 2 4 AT MANDLAY LINES AND QTR NO 15 1 15 3 AT TOC UNDER GE NORTH BANGALORE

Amount

B/R WORKS

Demolition of cement concrete (un-reinforced ) of any description and in any position not specifically provided for complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not specifically provided for complete all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, approachs, dado / partitions etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and as directed

Demolition of brick work /stone masonry/PCC block masonry built in cement mortar of any description all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) area not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc (distrubed surface of wall shall be make good by the contractor) all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) area exc. 1.5 sqm but n.exc. 4 sqm each, including cutting holes for removing the hold fast etc distrubed surface of wall shall be make good by the contractor) all as specified and as directed.

Taking down shutters of any description area exc. 1.00 sqm and not exc. 2 sqm each and removing from site complete all as specified and as directed.

Taking up or down steel tubing of 15 mm dia boreand connections including cleaning for refixing serviceable pipe or removal balance pipe to store complete all as specified and as directed.

Taking up or down steel tubing of 20 mm dia boreand connections including cleaning for refixing serviceable pipe or removal balance pipe to store complete all as specified and as directed.

Taking up or down steel tubing of 25 mm dia boreand connections including cleaning for refixing serviceable pipe or removal balance pipe to store complete all as specified and as directed.

Taking down cement plaster of any description hacking for key or raking out joints on old brick work / stone / concrete surface complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipe up to 100 mm dia incl fittings, jointed in cement mortar and taking out trenches if reqired etc complete all as specified and directed

Taking down PVC rain water pipes of any size or pattern including all fittings, head shoes etc complete all as specified and as directed.

Taking down existing un-serviceable water proofing treatment from roof slab and cleaning the roof slab by wire brush and removing WPT felt beyond the MOD premises etc complete all as specified and as directed

Dismantling water tanks exc. 500 ltr but not exc. 1000 ltr capacity and removing to store etc complete all as specified and as directed.

Dismantling water tanks exc. 250 ltr but not exc. 500 ltr capacity and removing to store etc complete all as specified and as directed.

Plain Cement Concrete (1:4:8), type D-2 using 40mm graded stone aggregate as in sub base to floors, 75mm thick complete all as specified and as directed.

Plain Cement Concrete (1:2:4), type B-0 using 12.5 mm graded stone aggregate as in floors 25mm thick, as in sub base to floor complete all as specified and as directed.

Vitrified ceramic tiles 8-10 mm thick, square / rectangular area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

All as per Sl Item No. 1.020 above but in skriting over and including backing coat of 10mm thick In CM(1:3)

Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Exterior grade, coloured, glossy finish rubber pressed, cement concrete designer chequered tiles of size 300 x 300 x 25mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floors etc laid over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Glazed ceramic coloured tiles of 300 x 450 x 7mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over and including backing coat 10mm thick in CM (1:3) on fair faces of brick work or concrete surfaces complete all as specified and as directed.

Machine cut Kota stone slab flooring 18-20mm thick, table rubbed,moulded exposed edge as equivalent to tread length (one piece) over and including cement screed base of 15 mm thick in Cm(1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding the edges as in half round including rubbing and polishing etc complete all as specified and as directed.

Machine cut Kota stone slab 18-20mm thick, table rubbed, moulded exposed edge, as equivalent to riser length (one piece) as in riser and steps, skirting, dado, over and including backing coat of 10mm thick in CM(1:3), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding the edges as in half round including rubbing and polishing etc complete all as specified and as directed.

18 to 20 mm thick Granite stone slab of any type, table rubbed and polished in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding the edges half round and polishing laid over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

TMT steel bars 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Precast cement concrete block masonry with solid blocks exc. 10 cm in width and setting in cement mortar 1:6 type C1 1:3:6 (using 20 mm graded aggregate) complete all as specified and as directed.

Precast Reinforced Cement Concrete (1:2:4), type B1, using 20mm graded stone aggregate as in cover slabs of man hole, chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including necessary form work set in CM (1:4) complete all as specified and as directed.

Factory made 1.25 mm thick pressed steel frames of size 125 x 60mm for doors with one or more rebates(02 rebates) including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and as directed.

Factory made 1.25 mm thick pressed steel frames of size 105 x 60mm for doors with one or more rebates(02 rebates) including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and as directed.

Plain Cement Concrete, (1:2:4), type B 1, using 20mm graded stone aggregate as in hold fast and filling of pressed steel chowkat etc including necessary form work complete all as specified and as directed.

Rolled Mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work complete all as specified and as directed.

35mm thick flush shutters, solid core construction with decorative choice lamination on both sides of shutter, kiln seasoned and chemically pressure treated complete all as specified and as directed.

18/19mm thick block boards, grade 1 quality, exterior grade, commercial type, water proof, termite proof, fixed with screws to timber frame-work as in cub board shutter, shelves etc fixed in repairs complete all as specified and as directed.

0.90 mm thick decorative laminates of type 1, surface finish, colour and pattern as approved, fixed with approved adhesive as per manufcturer's instructions, fixed to door/cub board shutters including teak wood beading 3mm thick and 18 mm wide including painting to match the existing colour etc complete all as specified and as directed.

Solid PVC door frame, single rebated of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete as sepecified and as directed. NOTE :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

Factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (Stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face and 2mm plain colour PVC sheet on back face etc., complete all as specified and as directed.

Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete fixed in repairs all as specified and as directed.

Powder Coated (minimum thickness of powder coating 50 micron) aluminium sections weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing (door and window), handles 2 Nos in each shutter, hinges, anodised aluminum snap beading screws etc complete all as specified and as directed.

4.0 mm thick sheet glass, ordinary quality and glazing with oil putty and glazing clips in metal frame and second class hard wood beading in wooden frames in squares not exceeding 0.5 sqm in each pane all as directed.

4.0 mm thick figured glass, ordinary quality and glazing with oil putty and glazing clips in metal frame and second class hard wood beading in wooden frames in squares exceeding 0.5 sqm in each pane all as directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and as directed. '

Aluminium anodised tower bolt 200 mm long of extruded section etc., complete all as specified and as directed.

Aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed.

100 mm thick stainless steel butt hinges, heavy weight, and fixed etc complete all as specified and as directed.

150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed.

150 mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floors etc complete all as specified and as directed.

Continuous (piano) hinges, 30mm width of flaps (when open), mild steel bright finish or electro galvanised fixed to wooden or angle iron frame complete all as specified and as directed.

Kitchen sink made of stainless steel 1mm thick kitchen with plugs, washers and wastes: including bedding in cement mortar to dwarf wall or including fixing cantilever brackets or fixing in granite slab and connecting union to pipe overall size 495mm x 420mm bowl size 410mmx 330mm x 160mm complete fixed in repairs all as specified and as directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC(SWR) 'P' or 'S' trap connecting to flush pipe and to anti syphonage pipe, etc. complete including making good to floor fixed in repairs complete all as specified and directed.

EWC with normal closing seat cover of size 540 x 375 x 415mm with S trap including connection to out going pipe, & seat cover and flushing pipe complete all as specified and as directed. MAKE:- Cat No. 4018 of Prayag of equivalent make of Cera / Hindware.

Vitreous china wash basin flat back of size 550x400 excluding taps but including 32 mm dia chromium plated waste fitting, PVC waste pipe 610 mm long and PVC connection 450 mm long complete fixed in repairs all as specified and as directed.

PVC dueo flushing cisrern valveless with flushing out valve low level of 10 Ltr capacity white with inlet ball valve, float, flushing bend & handle including brackets & connection to pipe etc including PVC connection 450 mm long complete all as specified and as directed. MAKE:- Cat No BA-502 of Prayag or equivalent make of Cera/ Hindware.

Bib cock with flange, fancy type, cast copper alloy chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete fixed in repairs all as specified and as directed. MAKE:- Cat No. 9206 of Prayag of equivalent make of CERA/HIND WARE.

15mm bore brass CP wall mixer with L bend, with provision of hand shower for mixing hot and cold water screwed down for iron pipe and fixed in repairs complete all as specified and directed. MAKE:- Cat No 9275 of Prayag or equivalent make of CERA/HINDWARE.

15 mm bore central holes mixer with out pop up waste system (9" spout) fixed in repairs all as specified and as directed. MAKE:- Cat No 9350 of Prayag or equivalent make of CERA/HINDWARE.

15 mm bore sink mixer with regular spout W/M etc complete fixed in repairs all as specified and as directed. MAKE:- Cat No 9360 of Prayag or equivalent make of CERA/HINDWARE.

Angle cock with flange, fancy type, chromium plated, brass cast copper alloy screwed down high pressure with crutch fixed for 15 mm dia bore pipe complete fixed in repairs all as specified and as directed. MAKE:- Cat No. 9210 of Prayag or equivalent make of CERA/HINDWARE.

Bottle trap (with internal partitions) 32 mm size with 250 mm & 190mm long wall connection pipe and wall flange etc complete fixed in repairs all as specified and as directed. MAKE:- PRAYAG / CERA /HIND WARE

Toilet roll paper holder complete fixed in repairs all as specified and as directed. MAKE:- Cat No. BA-38 of Prayag or equivalent make of CERA/HINDWARE.

Glass shelf 500 x125 mm with brass brackets complete fixed in repairs all as specified and as directed. MAKE:- Cat No. BEA-45 of Prayag or equivalent make of CERA/HINDWARE)

Full corner glass shelf with brass brackets complete fixed in repairs all as specified and as directed. MAKE:- Cat No. BEA-52 of Prayag or equivalent make of CERA/HINDWARE.

Soap dish holder with glass complete fixed in repairs all as specified and as directed. MAKE:- Cat No. BA-25G of Prayag or equivalent make of CERA/HINDWARE.

Overhead round rain shower 8" dia with out arms of 15 mm bore dia complete fixed in repairs all as specified and as directed. MAKE:- Cat No. BOS-41 of Prayag or equivalent make of CERA/HINDWARE.

Health faucet, ABS body with 1.2 mtr long SS braided rubber hose pipe & wall hook all as per Jaquar Cat No. ALD-CHR 583 or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Jet spray, brass chromium plated suitable for EWC / Ango Indian EWC including fittings fixed in repairs complete all as specified and as directed.

Bathroom cabinet mirror of moulded PVC of size 431.80mm x 355.60mm fixed in repairs to wall as specified and as directed. Make : Prayag or equivalent.

Stainless steel plate rack made out of of 0.63mm thick stainless steel sheet, over all size 990.60mm x 914.40mm with shape, capacity of utensiles and pattern as directed fixed in repairs complete all as specified and as directed.

Towel rack of stainless steel including fixing arrangements complete fixed in repairs all as specified and as directed. MAKE:- Cat Noo SS-1 of Prayag or equivalent make of CERA/HINDWARE.

Stainless steel grab bar towel rail 450 mm long including fixing arrangements fixed in repairs complete all as specified and as directed. MAKE:- Cat No. GM-04 of Prayag or equivalent make of CERA/HINDWARE.

Stainless steel towel ring including fixing arrangements fixed in repairs complete all as specified and as directed. MAKE:- Cat No. BA-41 of Prayag or equivalent make of CERA/HINDWARE.

16mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, fixed to wall, ceiling or laid in floors including all fittings and specials complete all as specified and as directed.

20mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, fixed to wall, ceiling or laid in floors including all fittings and specials complete all as specified and as directed.

25mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, fixed to wall, ceiling or laid in floors including all fittings and specials complete all as specified and as directed.

Rotational moulded polythene water storage tank (cylindrical vertical with closed top) with ISI mark embosed on it, hoisted and fixed in position complete all as specified in SSR part I capacity of tank 1000 ltrs capacity complete complete all as specified and as directed.

Rotational moulded polythene water storage tank (cylindrical vertical with closed top) with ISI mark embosed on it, hoisted and fixed in position complete all as specified in SSR part I capacity of tank 500 ltrs complete all as specified and as directed.

25 mm dia of bore ball float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and as directed.

Gun metal gate or globe valves 25 mm dia with iron wheel head, screwed both ends for iron pipe and fixed in repairs complete all as specified and directed

110 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints laid in trenches and necessary fittings fixed in repairs complete all as specified and as directed.

75 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints laid in trenches and necessary fittings fixed in repairs complete all as specified and as directed.

110 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints fixed to wall including PVC clamps and necessary fittings fixed in repairs complete all as specified and as directed.

75 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints fixed to wall including PVC clamps and necessary fittings fixed in repairs complete all as specified and as directed.

PVC (SWR) bends type 'B' of any radius, 110 mm dia complete all as specified and directed.

PVC (SWR) bends type 'B' of any radius, 75mm dia complete all as specified and directed.

PVC (SWR) vent cowl 110 mm dia, type 'B' all as specified and as directed.

Rendering 5 mm thick on concrete ceiling surfaces in CM (1:3) finished even and smooth without using extra cement all as specified and as directed.

15mm thick rendering on brick or concrete surface in cement mortar (1:6) and finishing the surface with even and smooth without using extra cement complete all as specified and directed.

Rendering 15mm thick in CM(1:4) mixed with water proofing compound as per manufacturers instructions finishing the surfaces even and smooth without using extra cement including necessary scaffolding complete all as specified and directed. NOTE:- WPC will be measured and paid separately under relavent items.

Plain Cement Concrete (1:2:4) type B1, using 20 mm graded stone aggregates as in copings, Chajja kerbs, roof padding/staging of water tank etc including necessary formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed

Rendering 15 mm thick in CM (1:3) on fair faces of brick work or concrete surface mixed with water proofing compound as per manufacturers instructions complete all as specified and as directed Notes : WPC shall be measured and paid seperately

Roof treatment by applying bitumen primer @ 0.27kg/sqm, providing 3mm thick APP modified water proofing membrane weighing not less than 3.8 kg/sqm reinforced with non woven polyester matt weighing not less than 180gm/sqm, having softening point not less than 140 centigrade, having tensile strength of 650 N/sq.cm in longitudinal and transverse directions, the reinforced tearing strength of 180N by torch application with minimum 10cm side overlap and 15cm end lap applying a coat of blown grade hot bitumen VG-10 over the membrane @ 1.2kg/sqm, top of membrane shall than be finished with solar reflective bituminous aluminium paint @0.10kg/sqm all as specified and as directed.

Providing and laying water proofing treatment to sunken portion of WCs, bathroom and kitchen etc by applying cement slurry mixed with two component elastomeric acrylic based polymer modified cementitious composite compound coating of make as approved in TI 5/2003 including demolition and removal of existing treatment of any type with the following procedure in sequence all as specified and as directed:- (i) Demolition of existing treatment of any type including cleaning and removal of debris from site. (ii) First layer of cement slurry @ 0.488 kg/sqm of cement mixed with acrylic based polymer modified cementitious composite compound @ 0.253 kg/sqm, the layer will be allowed to air cure for 4 hours. (iii) Second layer of cement slurry @ 0.242 kg/sqm of cement mixed with with acrylic based polymer modified cementitious composite compound @ 0.126 kg/sqm, the layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (iv) 20mm thick screed in cement mortar (1:3) mixed with including supply of liquid water proofing compound as per manufacturers instructions. Contd.. 1.96

Contd.. 1.95 (v) Ponding the treated portion atleast 48 hours, if any leakage / seepage observed the entire procedures will be repeated without any extra cost. (vi) Provide 40mm dia light grade GI spout at the lowest point with 30cm projection beyond the out face of the wall. (vii) Sunken portion shall be filled with lean cement concrete(1:5:10), type E-2 using 40mm graded stone aggregate. NOTE :- (i) The sunken slab sloped towards outer face to drain the water in to GI spout pipe. (ii) Coving shall be provided at the junction of slab with the wall. (iii) Nahni trap shall be 10mm below finished floor level and drain pipe dia is larger than the nahni trap size. (iv) The outer end of the spout should be chamfered. (v) mode of measurement : plan/floor area will be measured.

Supply only integral liquid water proofing compound all as specified and as directed.

Preparing newly plastered surface of ceiling and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

Complete removal of existing treatment of ceiling applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

Preparing new plastered surfaces of walls and applying uniform layer of 2mm thick Birla/Asian wall care Putty and applying two coats of oil bond distemper white or any tint over a coat of primer complete as specified and as directed.

Complete removal of existing treatment of wall and applying uniform layer of 2mm thick Birla/Asian wall care Putty and two coats of oil bond distemper white or any tint over a coat of primer complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of primer all as specified and as directed.

Preparation of old treated wall surfaces of any description including brooming down with steel wire brushing scrapping down smoke soot’s, moulds, moss and efflorescence, salts, trading oil and greasy spots etc and applying two coats of cement based paint on outer surfaces including in narrow width bands cornices splisters.all as specified and as directed.

Preparation of old painted wooden surfaces of any description exceeding 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of new or previously untreated steel and iron surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel over a coat of red oxide primer, complete all as specified and directed.

Preparation of old painted steel surfaces of any description exceeding 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Stainless steel decorative curtain rod of 25 mm bore with wood finishes (weight not less 400 gms per running meter) including fancy finale caps fixed in reapirs complete all as specified and as directed.

Stainless steel decorative brackets for curtain rod of dia 25 mm dia made out of stainless steel flat not less than 20 mm wide 1.50 mm thick and overall length not less than 160 mm fixed with screws min 2 Nos with rawl plug of size not less than 50 mm long fixed in repairs complete all as specified and as directed.

18mm thick, PVC sheet one side prelaminated of approved texture, Celuca ply of Rajshree or equivalent as approved by GE as in kitchen cabinet with shelves and partitions including necessary fittings and fixtures as per manufacturer's instructions complete fixed in repairs all as specified and as directed.

Stainless steel kitchen basket in various type of baskets susch as plaint basket height 4", Thali basket 8" height, Cup saucer basket 4" heigt, and perforated cutlury basket 4" height all as specified and directed.

Stainless steel channel for basket sizes 600mm long and 46mm wide all as specified and directed (Make : Hettich/Godrej)

Stainless steel auto closing concealed hinges 9.5 cranks for half overlay doors with opening angle 95* (14-32mm) with integrated overlay adjustment + 2.50mm & depth adjustment 4mm complete all as specified. Make : Godrej / Hettich.

Easy dry wall mounted stand consisting of 19 mm dia power coated MS base frame with a structure (Mesh) of 6 Nos of 2020 Grade SS rods of dia 5 mm and length 750 mm for drying clothes, with each mesh has total length of 4500 mm (approx 15 feet) of SS Rod, fixed in repairs all as specified and as directed.

35 mm thick factory made second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc, sizes of members of shutters as specifed in SSR part i, Section 8, cluase 8.24 (a) including two coats of synthetic enamel paint over a coat of pink primer and aluminum door closer etc complete all as specified and as directed.

Walling of square regular coursed well bonded, bedded and solidly hearted built in 1:4 including 40 mm thick graanite or trap stone hammer dressing including flush pointing etc complete all as specified and as directed

E/M WORKS

Taking down carefully aluminium/ copper wiring / power point wiring (light, fan,call bell socket or power circuits) complete and making good the disturbed surface of walls, ceiling etc., including painting with same colour of the back ground complete all as specified and as directed by Engineer-in-Charge.

Point wiring, modular type, complete with 1.5 sq.mm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and incl non-metalic rigid PVC conduit of medium grade ISI marked including accessories concelaed type wiring with GI/ MS branded sunken boxes of suitable module concealed in walls including modular frame and cover plates of suitable module fixed with cadmium plated iron screws for housing modular type switches, switch socket outlets, fan regulators etc., including provision of 1.5 sq.mm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly complete all as specified and as directed for :- (a) One light point controlled by one switch.

(b) One fan point controlled by one switch/regulator.

(c) One light point controlled by two 2 way switches.

(d) One 3 pin socket out let 5 Amps on independent board.

(e) one bell/buzzer point controlled by bell push.

(f) one 3 pin socket out let 5 A on same board.

Point wiring, modular type, complete with 2.5 sq.mm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and incl non-metalic rigid PVC conduit of medium grade ISI marked including accessories concelaed type wiring with GI/ MS branded sunken boxes of suitable module concealed in walls including modular frame and cover plates of suitable module fixed with cadmium plated iron screws for housing modular type switches, switch socket outlets, fan regulators etc., including provision of 2.5 sq.mm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly complete all as specified and as directed. NOTE FOR SL ITEM NO. No 2.002 to 2.008 :- (i) The earth wire for the points in the same circuit can be looped from point to point. (ii) Earth wire shall be taken inside the conduit. (iii) Cost of terminal box is deemed to be included in the item rate quoted for point wiring. (iv) Cost of a circuit of any length of cable from DB to any switch/ socket board to be included in point wiring.

LED batten fittings, 18 watts, 6000K, (4 feet long), suitable for indoor applications wall mounted with extruded aluminium heat shink provision, efficient heat dissipation and integrated electronic driver, industrial batten type, powder coated top cover, with bipin holders, connector block , lamp etc., complete all accessories internally pre wired all as per Bajaj, Cat No.BCLAB 18 WH LED P or techno commercially equivalent makes specified in PS including connecting up twin core twisted flexible copper conductor cable all as specified and directed.

LED tube light fittings, 10 watts, 6000K, (2 feet long), wall mounted with extruded aluminium heat sink provision, efficient heat dissipation and integrated electronic driver, industrial batten type, powder coated top cover, with bipin holders,connector block, lamp etc., complete all accessories internally pre wired all as per Bajaj, Cat No.BCLAB 10 WH or techno commercially equivalent makes specified in PS including connecting up with twin core twisted flexible copper conductor cable all as specified and directed.

LED luminaries, round 18 watt PERARL + LED Slim surface panel mounted type suitable for indoor application, complete with all accessories all as per Crompton Greaves Cat part No: LCDSPLN-R-18-CDL or techno commercially equivalent makes specified in PS including connecting up twin core twisted flexible copper conductor cable including taking down the existing all as specified and directed.all as specified and directed.

Modular switch 1 way, 6 Amps, one module including taking down the existing complete all as specified and as directed.

Modular switch 1 way 16 Amps, one module including taking down the existing complete all as specified and as directed.

Modular switch 2 way, 6 Amps, one module including taking down the existing complete all as specified and as directed.

Modular bell push, 6 Amps, one module including taking down the existing complete all as specified and as directed.

Modular socket, 6 Amps, 2/3 pin combined, two module including taking down the existing complete all as specified and as directed.

Modular socket, 6 Amps / 16 Amps, 2/3 pin combined, two module including taking down the existing complete all as specified and as directed.

Modular fan regulator, five stepped, 120 Watt, 2 Module including taking down the existing complete all as specified and as directed.

Angle holder PVC/polycarbonate type including taking down the existing all as specified and as directed.

MCB single pole and neutral 240 Volts, 32 Amps including taking down the existing un serviceable MCB complete all as specified and as directed.

MCB single pole 240 Volts, 5 to 40 Amps including taking down the existing un serviceable MCB complete all as specified and as directed.

MCB TPN 415 volts 63 Amps including taking down the existing complete as specified and as directed.

MCB DB, SPN 8 ways, 240 Volts with 200 Amps rated busbar, double door for housing MCBs all as specified and as directed.

MCCB DB TPN 4 ways double door vertical type 415 volts with 200 Amps rated busbar for housing of MCBs as specified and as directed.

Ceiling rose, surface bakelite type, 65 x 50 mm, 2 to 3 terminals all as specified and as directed.

Replacement of ding dong bell AC 230 volts single pole all as specified and as directed.

Sub main wiring with two runs of single core 6 sq.mm, 1100 volts grade multi stranded copper conductor cable along with one run of 6 sq.mm PVC insulated single core multistranded copper conductor cable as earth continuity conductor drawn through and including non rigid PVC conduit medium grade of suitable size including taking down the existing complete all as specified and as directed. NOTE: Two runs of 6 sq.mm cable, one run of 6 sq.mm earth continuity conductor and one run of PVC conduit shall be measured as one unit for payment purpose.

Earthing complete with galvanised steel plate electrode 600mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge not less than 1.5 m below ground level connected to earth lead by GI wire 4 mm dia by means of bolts nuts, check nuts, washers made out of galvanised iron connected to main switch all as shown in elect plate No 3 of MES SSR Part -I includingn excavation and earth work in any type of soil,funnel, 20 mm dia light grade GI watering pipe with chamber of PCC 1:3:6 type C1 40mm thick of size 450mm x450mm (1:2:4) type B1 for cover slab reinforced with 8mm dia TMT bars 10cm c/c both ways and with 6mm MS hook etc complete all as specified including testing on completion all as specified and directed.

45 Watt LED building security light with pressure die-cast housing along with prismatic polycarbonate modular secondary lens optics with IP-66 ingress protection and impact resistance of IK-08. 4kV inbuilt and 10kV external surge protection with top opening, driver cover for easy maintenance complete all as specified and as directed. MAKE:- Bajaj Cat No :- ENXT P 54L WH CR PC SD or equivalent model in Phillips and CG.

Brackets made out of GI tubing medium grade 25 mm bore, approx length 1.5 m long including MS clamps made out of MS flat iron 25 x 6 mm , nuts, bolts, washers etc and including before fixing applying two coats of aluminum paint over a coat of red oxide primer including removing the old existing GI bracket from building complete all as specified and directed.

Sheet metal enclosure single pole and neutral with a two pin earth plug and socket with one single pole MCB 20 Amps, 230 Volts AC complete all as specifeid and directed.

Point wiring complete with 1.5 sq.mm single core FRLS PVC insulated unsheathed cable 1100 volts grade with multi stranded copper conductor conforming to IS 694 drawn through and including non-metalic rigid PVC conduit medium grade with accessories concealed type run on walls/ ceiling including MS terminal boxes fabricated with 1.6 mm thick MS sheet concealed mounted on walls with hylam laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., including provision of 1.5 sq.mm FR PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed for :- (a) One Light point controlled by one switch.

(b) One fan point controlled by one switch and regulator.

(c) One bell point controlled by one bell Push

(d) One 3 pin socket out let 5 Amps on independent board.

(e) one 3 pin socket out let 5 Amps on same board.

(f) One light point controlled by two 2 -way switches.

Point wiring complete with 2.5 sq.mm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with copper conductor conforming to IS 694 drawn through and including non-metalic rigid PVC conduit with accessories surface type run on walls/ ceiling with MS terminal boxes fabricated with 1.6 mm thick MS sheet concealed on walls with hylem laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., including provision of 2.5 sq.mm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed. NOTE FOR SL ITEM NO. No 2.032 to 2.038 :- (i) The earth wire for the points in the same circuit can be looped from point to point. (ii) Earth wire shall be taken inside the conduit. (iii) Cost of terminal box is deemed to be included in the item rate quoted for point wiring. (iv) Cost of a circuit of any length of cable from DB to any switch/ socket board to be included in point wiring.

Switch Piano, flush type, 5 Amps, 240 Volts single pole, one way with ISI marked complete all as specified and as directed.

Switch socket combination 3 & 2 pin, 5 Amps, 240 Volts, flush type multipurpose controlled by one switch all as specified and as directed.

Switch socket combination 2 in 1, 3 pin and 2 pin, 5 and 15 Amps flush type, universal complete all as specified and as directed

RCBO four pole 100 mA, 415 volts, 63 Amps for earth leakage ,over load and short circuit protection including taking down the existing un serviceable RCBO complete all as specified and as directed.

Stepped type electronic fan regulator flush type all as specified and as directed.

Bell push, flush type, 5 Amps, 240 Volts single pole with ISI marked complete all as specified and as directed.

Switch Piano, flush type, 5 Amps, 240 Volts single pole, two way with ISI marked complete all as specified and as directed.

Replacement of RCBO double pole 30 mA, 240 Volts 32 Amps 10 KA breaking capacity all as specified and all as directed.

Taking down the existing ceiling fans 1200mm sweep from its position by duly disconnecting electric wire and refixing the same in original position & connecting the electric lines after the painting of ceiling fan complete in situ with synthetic enamel white paint by spraying including filling cavities with one filler coat after cleaning all the dust all as specified and as directed.

Servicing of Geyser by preparation of old painted surfaces and painting the geyser with one coat of spray paint of white enamel replacing with 15 Amps 3 pin top connection all as specified and as directed.

MCB DB SPN 4 way 240 volts, double door, with 200 Amps rated busbar for housing MCBs all as specified and as directed.

Storage type water heater 25 Ltrs BEE 5 star rated completed including steel wired pipe for hot/cold water connection for inlet and out let water etc complete all as specified and as directed. Make: Bajaj Cat Part No. Model No. 150800 CANDIA or equivalent in Recold / Venus / Havells.

UNIVERSAL ENGINEERING

Karthick Constructions

Atom Engineers and Builders

SHANKAR