SPL REPAIR TO EXISTING FLOOR AND ROOF OF MT GARAGE BUILDING NO P-21 AT 411 (I) PARA FD COY UNDER GE (EAST) AGRA

Amount

Demolition of cement concrete in ground floor and paving n exc 15cm thickness (below or above the ground level) built in cement mortar complete all as specified and directed.

M&L cement concrete type B2, 1:2:4 (40 mm graded aggregate) 100 mm thick as in floor fair finish for laying wear proof topping complete all as specified and directed.

M&L 20 mm thick Wear proof topping as specified (incorporating an approved metallic floor hardner), laid on concrete floors and pavings, and finished even and smooth (except metallic hardner) complete all as specified and directed. Note : Metallic hardner shall be measured and paid in item No 5.00

Supply only glass dividing strips 3 mm thick of width 20/22 mm complete all as specified and directed.

Supply only metallic floor hardner for floor finishes and paving (as approved by GE nito bond EP base resin FOROC) complete all as specified and directed.

Taking down cement or cement lime plaster of any description on brick or stone walls/ ceilings etc, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on brick or concrete surface complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces at any height (not.exc 11mtr) complete all as specified and directed.

Dismantling of asbestos cement (corrugated and semi corrugated etc) sheet in roof cobvering complete all as specified and directed.

S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet AZ - 150 thickness of sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F 0.63 mm plain galvanised mild steel sheeting, in ridges, hips, valleys, gutters, drip and straight flashings( including necessary wooden plugs, nut and bolts, welding and connected materials at any height up to four stories buildings) with grade of zinc coating 275 including fixed with L or J type hook bolts complete all as specified and directed.

Taking down rolling shutters and re-fixing to its original position after cleaning all parts, straightening rails, changing damaged strips, bottom rail, guide rail, helical spring as required, greasing, oiling, painting servicing for smooth functioning of all parts completed all as directed for the following sizes :- Note: Lath strips, bottom rail, spring, gears, guide rail etc. will be measured and paid separately as supply only. Area of rolling shutter n.exc 10sqm each

M&L for preparation of old painted steel surfaces & applying one coat of synthetic enamel paint on steel surface of any description over 10 cm in width or girth complete all as specified and as directed.

Supply only mild steel spring made out of 6mm to 11mm dia high tension steel wire confirming to IS 4454 having 65 to 100 helical for rolling shutter for smooth working condition complete all as specified and directed (dia of spring 100mm to 150mm)

Supply only for replacement of existing unserviceable gear box with new gear box made out of 1mm thick mild steel sheet including painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Supply only 75mm wide laths strips 1mm thick for rolling shutter including mild steel clips at either ends duly painted with and including two coats of synthetic enamel paint (shades to match with the existing) over a shop coat of red oxide primer complete all as specified and directed.

Supply only mild steel bottom rail lock plate with two handles 150 mm wide and 3mm thick including necessary locking arrangement on both sides and painting to bottom rail with and including two coats of synthetic enamel paint to match with existing over a shop coat of red oxide primer complete all as specified & directed.

Supply only Ball bearing for rolling shutters complete all as specified and directed.

Supply only 65 to 75mm wide guide rail, 3mm thick suitable for rolling shutter complete all as specified and directed.

S&F in repair steel rolling shutters,1 mm lath thickness with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated, gear operated type with bevel gear box and crank handle etc complete all as specified and directed.

S & F in repair of 1 mm thick top cover galvanized iron sheet for steel rolling shutters complete all as specified and directed.

Taking down Chowkhats or frames not exc. 1.5 sqm but (without taking off shutters from the frames each complete all as specified and directed.

S & F factory made steel windows with side hung shutters including box type hinges with Z section steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F factory made steel windows with side hung shutters including box type hinges with Z section steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S & F mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed in steel frame/wooden and fixed with stainless wire staples complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality, plain/frosted on one side for window/ventilators in square not exceeding 0.50sqm each pane complete all as specified and directed.

M & L 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc including fixed with L type or J type hooks or cranked bolts etc complete all as specified and directed.

S & F 6 mm thick A. C. serrated ridge for corrugated or semi corrugated sheets as in ridge fixed with L or J type hook etc complete all as specified and directed.

S&F steel work in tubular post / other work including special shaped washer etc for strengthening existing steel structure as in purlin etc complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

Cement concrete type D-2, 1:4:8 mix (using 40mm graded stone aggregates) as in Sub base of flooring of 75mm thickness complete all as specified and directed.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand in repair complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge n. exc. 63 mm, bricks deposited, spread and levelled in layers n. exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in copings, kerbs, benching and the like, including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

M&L for preparation of new painted steel surfaces priming with red oxide & applying two coat of synthetic enamel paint on steel surface of any description over 10 cm in width or girth complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed and removing from site.

M&L point wiring with 1.5 sqmm multi stranded copper conductor 1100 volts. grade FRLS PVC insulated unsheathed cable with proper colour coding drawn in including PVC concealed conduit not less than 20 mm dia with all accessories and FRLS PVC insulated 1.5 Sqmm multi standard sheathed copper wire for continues earth, sunk in cast iron/Pressed steel terminal boxes 60 mm deep & 1.6 mm thick duly painted with aluminum inside and anticorrosive paint out side/PVC polycarbonate PVC rectangular block 50 mm deep, including 3 mm thick plastic laminated sheet for mounting switches, sockets, fan regulators etc connecting earth and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles. Note :Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit is not feasible at no extra cost for the following :- (a) One light /fan point controlled by one switch

(b) One 3 pin socket outlet 5 amps on the same board with other switches

All as per item No 37.00 here in before but with cable size 4 Sq mm for one 5 pin 15/16 Amps socket out let on independent board and multistrand insulated copper earth continuity conductor of size 4 sqmm complete all as specified and directed.

Supply and fix switch piano flush button single pole one way 5 amps 240 volts with polycarbonate body complete all as specified and directed.

Supply and fixing piano switch 16 Amp , 240 volt all as complete all as specified and directed.

Supply and fix socket 5 amps 5 pin flush type, 240 volts with polycarbonate body complete all as specified and directed.

Supply and fixing 16 Amp socket, multipurpose as complete all as specified and directed.

Supply and fix ceiling rose , 3 phase/PVC/ polycarbonate, isolated body surface Bakelite 65mm dia three terminals complete all as specified and directed.

Supplying and fixing 20 watt LED battan surface / wall mounted with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly pre-wired upto terminal block, power consumption < 20W, luminaire lumens > 2000 lms, driver efficiency > 85%, power facor > 0.95 THD < 20% as per IEC 61000-3-2, colour temp - 6500 K Surge protection 2.5 KV, 50000 burning hrs (min) as per L 70 criteria, two stages isolated constant current operated driver with range 150 - 270 VAC and safety extra low voltage safe level < 60 VDC as per IEC standard with LM 70 & 80 certification and connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.75 Sqmm and fixing arrangements for fixing the light fitting, complete all as specified and directed.

Supply & fixing LED security light 35 watt with aluminium pressure diecast housing, IP 65 protection, luminaire lumens > 3000 lumens and in built electronic driver prewire upto terminal block with driver efficiency > 85 %, power factor > 0.95, as per IEC 61000-3-2, colour temp 6500 K Surge protection 3.5 KV, 50000 burning hrs (min) as per L70 Criteria, multi stage constant current operated driver with range 150-270 VAC and safety exra low voltage safe load < 60 VDC as per IEC standards with LM 70 & 80 certification complete all as specified, fixed to pole or wall of buiding with and including suitable Bracket made out of 25 mm dia GI light grade pipe, 1.00 m long bent to shape by cutting & welding as required & directed and fixed with two Nos of FI clamps 50x6 mm to be tightened with suitabe size of bolts, nut and washers and including painted with two coat of aluminium paint over a coat of red oxide primer, and including connecting the fitting to electric source with & including twin twisted copper flexible wire of size 0.75 Sqmm including all accessories and fixing arrangements for fixing the light fitting complete all as specified & directed.

M&L for Wiring for circuit/submain wiring with two single core FRLS PVC insulated unsheathed multistranded flexible copper conductor cable of size 2x1.5 sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor 1x1.5 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in existing conduit complete all as specified and directed.

Supply and fixing in repair sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 8 way with IP-43 protection double door complete with appropriate size bus bar and neutral link complete all as specified and directed.

Supply and fixing in repair MCB SP 1 to 32 Amp rating 240V, 10KA 'C' curve and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified & directed.

Supply and fixing in repair MCB SPN 40 to 63 Amp rating 240V, 10KA 'C' curve and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified & directed.

Materials and labour as in replacement for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level ) with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized steel wire 4mm dia as earth lead soldered and riveted to earth plate by means of nuts, bolts, check nuts & washers, of galvanized iron or steel with connected to test point and testing on completion including 15mm GI light grade pipe for earth lead protection from earth point to earth plate, including provn adequate quantity of charcoal dust mixed with 35 % common salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth plate with 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire mesh with and including all necessary excavation & earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c Both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and as directed. NOTES:- (i) On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor.

3Krishna Enterprises (BID ID -3126542)

Balaji Associate (BID ID -3124725)

aman construction & general suppliers (BID ID -3126886)

N.K. ENTERPRISES (BID ID -3126321)

M/S RADHEY GOVIND ENTERPRISES (BID ID -3126498)

SahaDevSingh Constructions (BID ID -3126489)

M/s Kok Singh Sisodia (BID ID -3126496)