SPL REPAIR TO BOUNDARY WALL AT CERTAIN LOCATION AT BENGDUBI MIL STN UNDER GE BENGDUBI

Amount

Demolition of brick work or rubbled stone masonry including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework and pre-cast cement concrete articles built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position, not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and any position, not otherwise specifically provided for, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description and any position, not otherwise specifically provided for, complete all as specified and as directed.

Dismantling of barbed wire, complete all as specified and directed.

Excavating in trenches n.exc. 1.50m wide and n.exc 1.50m in depth for foundation, laying of cable, pipe etc and getting out in soft/loose soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and directed

Removing excavated material to a distance not exc 50.00 mtr and depositng where directed at a level n.exc 1.5m above the stating point, complete all as specified and as directed.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete, complete all as specified and as directed.

M&L for reinforced cement concrete M-25 (Design Mix) as in foundations, including rafts, footings, foundation beams, plinth beams, base of columns, etc basement slabs, under reamed piles and mass concrete, complete all as specified and directed. Note: Reinforcement and Form Work shall be measured and paid for seperately.

M&L for reinforced cement concrete M-25 (Design Mix) as in beams, cantilevers, bressummers, lintels, beams over 1.5 m span, etc, complete all as specified and directed. Note: Reinforcement and Form Work shall be measured and paid for seperately.

M&L for reinforced cement concrete M-25 (Design Mix) as in columns, pillars, piers, post, sturts, etc, complete all as specified and directed. Note: Reinforcement and Form Work shall be measured and paid for seperately.

M&L for Brickwork with fly as Bricks, straight or curved on plan exc 6m mean radius built in Cement morter 1:6, complete all as specified and directed

Use and waste formwork to sides of concrete foundations, footings, base of columns, raft and raft beams, sides of soffits (if any) of foundation and plinth beams and similar work, vertical or to better for rough flat finished surfaces of concrete, complete all as specified and directed.

Use and waste formwork to sides of pillars, post, sturts, piers, columns and stanchions,etc, for rough finished surfaces of concrete, square or rectangular, complete all as specified and directed.

Use and waste formwork to sides of soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves, including supports, overhangs, etc also splays between floors and beams, etc, for rough and flat finished surfaces of concrete, complete all as specified and directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

M&L TMT bars 8mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and as directed.

S&F MS angle iron, flat iron, etc,using steel conforming to Fe-250 Gde E-165 as in post and sturts in fencing including cutting tops to shape as directed, drilling holes, notching of wire, etc, including all necessary drilling, bolting or riveting, embedding in concrete, fillets for securing wire-mesh, etc and similar work , complete all as specified and directed.

S&F Galvanized, 2 strand, steel barbed wire. 2.24 mm dia, barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins, etc, each line wire to be measured separately, complete all as specified and directe.

S&F 5 to 10 mm diameter of neck mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with hexagonal or square washers and one nut length of bolt exc 10 cm and n. exc 15 cm long, complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces finsihed even and smooth (without using extra cement), complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:4) on other than fair faces of brick work or concrete surfaces finsihed even and smooth (without using extra cement), complete all as specified and as directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of cement based paint, complete all as specified and directed.

M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

M&L for broken glass coping on top of wall fixed with CM 1:3, complete all as specified and directed.

M/S ASHWIRBAD WOODCRAFT

M/S G D CONSTRUCTION

M/S JYOTI SHARMA AND SONS