GE/PKT-39/2020-21 SPECIAL REPAIR TO BLDG NO. NP-11/01 TO NP-11/04 OR MD ACCN AND PROVN OF TOILETS, BATHROOM, URINAL AT CERTAIN LOCATIONS UNDER GE (WEST) PATHANKOT

Amount

Suface excavation n exc (not exceeding) 30cm deep and averaging 15cm deep and getting out soft and loose soil complete all as specified and directed.

M&L for Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m area on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D-2 (40mm graded curshed stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (40mm graded crushed stone aggregate) 75 mm thick as in sub base concrete surface finished even & fair complete all as specified and directed.

M&L for Hardcore of broken boulder gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for earth filling under floor including spreading in layers n exc. 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5 m high from base complete all as specified and directed.

Material and labour for sand filling under floors or in foundations including watering and consolidation or layer of sand cushioning below interlocking paver block complete all as specified and as directed.

M&L for Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

M&L for Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for Reiniforced cement concrete 1:2:4 Type B-I nominal Mix (20mm graded curshed stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for Reiniforced cement concrete 1:2:4 Type B-I nominal Mix (20mm graded curshed stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for Reiniforced cement concrete 1:2:4 Type B-I nominal Mix (20mm graded curshed stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Material and labour for RCC type B1 (1:2:4) using 20 mm graded aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like such as cover slab of septic tank/soak well etc complete all as specified and as directed. Note for item No. 10 to 13:- Reinforcement shall be measured and paid separately).

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat rough finish surface of concrete complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc flat rough finished surfaces of concrete complete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions flat rough finished concrete surface complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat complete all as specified and directed.

Material and labour for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and as directed.

All as per Srl item No -18 here-in-before but 6mm to 8mm dia of TMT bar complete all as specified and directed.

All as per Srl item No -18 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

Supply and fixing of second class hard wood plain fillets, square, rectangular or triangular in section, and secured with nails or screws, clean sawn sectional area exc 13 Sqcm but not exc 25 Sq cm complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises and removing the debris outside from defence land complete all as specified and directed .

M&L for green Marble work 18-20mm thick (table rubbed and polished ) in cooking plateform and like in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade green over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 etc complete all as specified and directed

M&L for 20mm thick granite (pure black) work (table rubbed and polished) in steps, jambs pillars, window cills ,cooking platform and like including pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade or granite over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 etc complete all as specified and directed. Note:- The stone slab shall be in one piece over kitchen plateform,making gas pipe holes 25mm dia with rounded holes and all open edges to be half rounded.

Material and labour for coloured Glazed ceramic tiles in vertical surface such as dado/ skirting etc 450mmX 300mmX 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and as directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

Supply and fixing of joint free non skid Ceramic tiles, coloured 7mm to 8mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for 25mm thick Cement concrete in sub base for receiving floor tiles and mass concrete using PCC 1:2:4 Type B1, (20 mm graded crushed stone aggregate) complete all as specified and directed. Note:- Finishing surfaces of concrete to be even and rough to receive the topping layer or floor tiles etc complete all as specified and directed.

M&L for 40 mm thick cement concrete type B1 , 1:2:4 (20 mm graded crushed stone aggregate) finished even and smooth without using extra cement as in flooring complete all as specified and directed.Note- Glass dividing strips shall be measured & paid separately as Supply only.

Supply only 38 mm wide and 3 mm thick glass dividing strips in flooring fixing in position and making square or rectagular for casting concrete in flooring complete all as specified and directed.

Material and labour for chequred cement concrete tiles 30 cm x 30 cm x 25mm thick rubrised, glossy finish, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments to match the shade over and including 20mm thick secreed bed or bedding layer in CM 1:6 complete all as specified and directed.

S&F of Cement concrete tiles 25cm x 25cm x22mm thick, with grey cement & pigment machine pressed; set, jointed & pointed in neat cement slurry in floors ,path & cut , polished over and including 20mm thick secreed bed or bedding layer in CM 1:6 complete all as secified and as directed.

M&L for non abrasive paving (endura) tiles 300mm x 300mm x10mm thick (square/ rectangular) polished, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm screed bed in CM 1:4 complete al as specified and directed.Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles complete all as specified and directed.

Material and labour for machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade rubber moulded glossy finish with grey cement and pigment complete all as secified and as directed. Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other, Colour of paver blocks,laying pattern approved by GE.

Demolition of cement concrete or lime concrete (unreinforced) in ground floors and Pavings not exc 15 cm thick (below or above ground level ) and removing the debris outside from defence land complete all as specified and directed .

Material and labour for Cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight complete all as specified and directed.

Demolition of cement concrete or lime concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing the debris outside from defence land complete all as specified and directed .

M&L for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregates as in surface channels and drains complete all as specified and as directed.

Material and labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified and directed.

Demolition of brick work , built in cement mortar or cement lime mortar including all quions, arches, pillars, etc and disposal of debris out of MoD land complete all as specified and directed.

M&L for Brickwork with subclass 'B' old size bricks, straright or corved on plan exc 6m mean radius built in Cement mortar 1:6 complete all as specified and directed.

All as per serial item No 40 here-in-before but except old size sub class 'B' bricks. NOTE: Old bricks retrieved from demolition shall be used.

M&L for Brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

All as per serial item 42 here-in-before but except old size sub class 'B' bricks. NOTE: Old bricks retrieved from demolition shall be used.

Taking down cement plaster of any description and thickness on walls/ceilings etc including racking out joints, hacking for key, scrubbing down with water etc including necessary scaffolding up to four storeys height of bldgs if required and removing of debris out of MoD land complete all as specified and as directed.

M&L for Rendering 15 mm thick in cement mortar 1:4 on wall & floor brick/concrete surface finished even and smooth (without using extra cement ) and mixed with water proofing compound as per manufacturer’s instructions complete all as specified and directed. (WPC shall be paid separately)

Material and labour for rendering 15mm thick in CM 1:4 mixed with liquid water proofing compound (as per manufacturer’s instructions) on fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed. (Note:- WPC shall be measured and paid separately)

Material and labour for two coat plaster 35 mm thick (20 mm + 15 mm) on rough concrete surfaces of fin, facia, chajjas and similar article in CM 1:3 with liquid water proofing compound (as per manufacturer’s instructions) mixed in both coats, finished even and smooth without using extra cement including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.(Note:- WPC shall be measured and paid separately) Note :- Two coat plaster shall be carried out as mentioned in clause 14.18 of SSR-2009, Part-I complete all as specified and directed.

Material and labour for rendering 15 mm thick in CM 1:6 on other than fair faces of brick work , concrete surfaces of wall,fin, facia, chajjas,parapet and similar article etc finishing surfaces even and smooth without using extra cement including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.

M&L for Renduring 5mm thick in ceiling in CM (1:3) surface finished even and smooth with out using extra cement complete all specified and as directed.

Material and labour for 10 mm thick rendering on brick work or concrete surfaces in CM 1:3 as in ceiling of roof slab,fin, facia, chajjas,parapet and similar article etc finishing surfaces even and smooth without using extra cement including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of ceiling and applying three coats of white wash without any brush marks on the surface including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.

M&L for Prepration of new plaster surface of wall applying three coat of white wash complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of Cement Base Paint without any brush marks on the surface in any colour over and including a coat of alkali resistant primer (as per manufacturer’s recommendations) including necessary scaffolding up to four storeys height of bldgs,Shade/colour shall be approved by GE complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of wall and applying 2mm thick wall care putty on the surfaces & making the surface absolutely smooth and applying two coats of distemper oil emulsion finished without any brush marks on the surface in any colour including necessary scaffolding up to four storeys height of bldgs if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of exterior grade emulsion paint (weather proof/weather coat) without any brush marks on the surface in any colour over and including necessary scaffolding up to four storeys height of bldgs,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

Material and labour for complete removal of existing treatment on surface of wall and applying two coats of exterior grade emulsion paint (weather proof/weather coat) without any brush marks on the surface in any colour including necessary scaffolding up to four storeys height of bldgs if required,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

Material and labour for complete removal of existing treatment on surface of wall and applying 2mm thick wall care putty on the surfaces and making surface absolutely smooth and applying two coats of distemper oil emulsion without any brush marks on the surface in any tint including necessary scaffolding up to four storeys height of bldgs if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

Material and labour for complete removal of existing treatment on surface of wall and applying one coat of primer (as per manufacturer’s recommendations) on the surfaces and applying two coats of distemper oil emulsion without any brush marks on the surface in any tint including necessary scaffolding up to four storeys height of bldgs if required ,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

Material and labour for preparation of old plastered or un-plastered surface of wall by brooming down or steel wire brushing,scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of cement base paint of any colour without any brush marks on the surface including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.

Material and labour for Painting lines, dashes, arrows, letters, etc. on roads, pavements & the like exc 10cm wide with road marking paint, white or golden yellow or any colour etc including preparation of previously treated surfaces of road to receive the painting complete all as spd and directed. Note:-(a) The rates included for provision of red signals to keep off traffic from wet paint, cleaning road surface and working during odd hours when traffic is light. (b) 'The line painting shall stand out boldly and solidly without showing signs of brush marks or surface underneath. If necessary, the surface shall be repainted until the desired result is obtained as directed by GE & Shade/Colour shall be approved by GE.

Material and labour for writing letters or figures (block, Roman, Italic or Indian) exceeding 15 centimeter high but not exceeding 30 centimeter high etc with synthetic enamel paint including necessary scaffolding up to four storeys height of bldgs if required,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

Material and labour for Stops, commas, short lines, dashes, hyphens, brackets, etc. including necessary scaffolding up to four storeys height of bldgs if required,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

Material and labour for obliterating the old writing of any description, not exceeding 0.1 square meter, with paint to match with the existing work including necessary scaffolding up to four storeys height of bldgs if required,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

Material and labour for repairing of chajjas, roof projection and faces of exposed reinforcement surface or damaged loose RCC surface and applying one coat of cement slurry @3kg/Sqm and filling with cement concrete 1 : 2 :4 type B-0 (using 12.5 mm graded crushed stone aggregate ) mixed with liquid water proofing compound (as per manufacturer’s instructions) and finished with 05mm thick rendering with cement sand mortar 1 : 3 with liquid water proofing compound (as per manufacturer’s instructions) using coarse sand in patch area not exc 1.00 sqm each and thickness of RCC member not exc 150 mm and reinforced with welded mesh of weight exc 2.00 Kg per sqm but not exc 3.00 Kg per sqm and finally applying two coats of exterior grade emulsion paint (weather proof/weather coat) without any brush marks on the surface in any colour over and including one coat of primer (as per manufacturer’s recommendations) including necessary scaffolding up to four storeys height of bldgs,Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

Material and labour for complete removal of existing treatment from ceiling surface and applying two coat of white wash on undecorated surfaces without any brush marks on the surface including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.

Demolition of Roofs, floors (other than ground floors), beams staircases, landing, chajjas, & similar suspended work cement concrete is reinforced (reinforcement cut as required to facilitate demolition) and disposal of debris out of MoD land complete all as specified and directed.

Demolition of existing roof treatment of any description such as wornout tarfelt, mortar of any description & any thickness,shurves vegetation,tree,terracing tile (where as reqd) or concrete bedding and Cleaning of all foreign material such as fungus, mass, dust ,debris etc by brushing and dusting,washing down with water,surface shall be levelled with a layer of 20 mm thick screed bed in CM 1:4 including mixed with water proofing admixture as per manufacturer's instrucions and applying roof treatment on top of roof with APP modified membrane with non-woven polyster reinforcement(centre core) with thermal insulation with white mineral gravel finish on upper side of weight not less than 3.5 kg/sqm & thickness not less than 3mm, laid by torch application method with overlap 100 mm on length side and 100 mm on the width side as per manufacturer's instructions over a coat of approved cold applied bituminous oil based primer (IS-3384) @0.30 litre/sqm complete all as specified and directed (Note:- WPC shall be measured and paid separately)

Material & labour for cleaning of plastered /concrete surfaces and applying priming coat using bituminous primer @ 0.30 Kg/Sqm. followed by applying evenly a tack coat @ 1.20 Kg/Sqm. using with 85/25 grade bitumen and 3mm thick APP modified polymeric water proofing membrane with non woven polyester reinforced of weight not less than 3.6 Kg/Sqm. unrolled and bonded to substance with side and end laps 75mm and 100mm respectively as per manufacturer’s instructions and finishing top of APP water proofing polymeric membrane with a coat of hot blown industrial bitumen 85/25 grade @ 1.20 Kg/Sqm and finally finished with a coat of bituminous aluminium paint @ 0.20 Kg/Sqm surface shall be levelled with a layer of 20 mm thick screed bed in CM 1:4 including mixed with water proofing admixture as per manufacturer's instrucions complete all as specified and directed.

M&L for PCC 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregate) mixed with water proofing compound as per manufacturer’s instructions as in padding on roof, surface finished even and smooth without using extra cement all as specified and as directed.(Note:- WPC shall be measured and paid separately)

M&L for Providing cement concrete 1:2:4, type B-1, (using 20 mm graded crushed stone aggregate) mixed with water proofing compound as per manufacturer’s instructions as in roof kerbs,bands etc or mud stops, rounded or chamfered on edges complete all as specified and as directed.(Note:- WPC shall be measured and paid separately)

Supply only `Liquid Water Proofing Compound. complete all as specified and as directed .

M&L for cutting out cracks to V-Section in existing roof or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand in ratio 1:1 by weight complete all as specified and directed.

Material and labour for cutting down plants / trees of girth not exc 15 cm & surface area not exc 0.36 Sqm each from roof tops /sides of external walls of buildings, chajja, wall junctions, junctions of of rain water / soil /waste vent pipes including taking out roots entered in wall/slab surfaces and pouring chemical for burning of roots etc. making good the surfaces including repairing the CI/GI/PVC joints of affected locations by applying TUFALO (herbal medicine )and making good to suit the adjoining surfaces using PCC type 1:2:4, type B-O or cement mortar 1:2 complete all as per manufacturer instructions and as specified. NOTE: Any CI/GI/PVC pipes and fittings damaged during work shall be replaced by new one to insure leakage / seepage free joint without any extra cost to the department and Unit rate quoted by tenderer shall included for use of all scaffolding, trestles, ladders, cradles etc ,hoisting, lowering and protective measures etc up to four storeys height of bldgs and removing of debris out of MoD land complete all as specified and as directed.

Material and labour for for precast reinforcement cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar (1:4) complete all as specified and as directed. Note:- Reinforcement shall be measured and paid separately).

Taking down chowkhats or frames exc 1.50 and n.exc 4 Sqm each (without talking off shutters from the frame) complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frames) area not exc1.5 Sqm each and removing from site complete all as specified and directed.

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each and removing from site complete all as specified and directed.

S&F of Steel window/ventilator factory made box type and shutter (double shuter) with sash bar made out of section using flash butt welding, complete including hinges ,tower bolt,handle , grill made out of 10 mm sq bar including two coat of synthetic enamel paint over and including one coat of red oxide primer, tarred hold fasts, PCC blocks, including plain/figured glass and stainless steel wire mesh 0.56 mm nominal dia of wire and average width of aperture 1.18 mm all as shown on drg No CEPZ /TD-245/01 sheet 1/1 and CEPZ /TD -246/01 sheet No 1/2 & 2/2 complete all as specified and directed. including taking down existing spoiled and unserviceable windows/ventilators of any type ( wooden/steel) complete all as specified and directed

S & F of pressed steel frames 105 x 60 x1.25 mm with one or more rebates including necessary fixing of lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate including one shop coat of primer complete all as spd and directed

S & F pressed steel frames 125 x 60 x1.25 mm with one or more rebates including necessary fixing of lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate including one shop coat of primer complete all as spd and directed

M & L for cement concrete 1:3:6, type C-0 using 12.5 mm graded crushed stone aggregate as in back filling of hollow portion of frame with plain cement concrete and for fixing of hold fast complete all as specified and directed.

Supply and fixing of 40mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed

Supply and fixing of Factory Made Solid PVC flush door shutter with wood free EPS core, 28 to 30mm thick (stiles), with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face Supplying & fixing in frame at site as per specification & drawing complete all as specified and directed

Supply and fixing of 35mm thick factory made 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); Supply and fitted to chowkats Note: wire cloth shall be measured separately

Supply and fixing of stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixing with stainless steel wire staples or using metal nut and bolts complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and directed.

Supply and fixing of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet & edges will be painted to match with printed sheet ,reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

Supply and fixing of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) used instead of exposed portion of PVC sheet beading suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

Supply and fixing of stainless steel butt hinges of size 100mm long for fixing of pvc door shutter etc complete all as specified and directed.

Supply and fixing of butt hinges medium weight 100 mm cold rolled mild steel complete all as specified and directed..

Supply and fixing of Aluminium, anodised, barrel tower bolts of extruded section, Length of bolt 150mm complete all as specified and directed

Supply and fixing of Aluminium, anodised, barrel tower bolts of extruded section, Length of bolt 200mm complete all as specified and directed

Supply and fixing of Aluminium handles, cast type, anodised Size of handle in 150mm complete all as specified and directed.

Supply and fixing of Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing of clips of sheet, cast or extruded sections and fixing of bolts and sliding bolts of extruded sections or cast aluminium alloy Length of bolt 250 mm complete all as specified and directed.

Supply and fixing of Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. fixing in floor Overall length of cover plate 140mm complete all as specified and directed.

Supply and fixing of 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate including welding to steel frames complete all as specified and directed.

Supply and fixing in repair 25mm outer dia stainless steel decorative drapery rod ( Model No- SS-25FL of Vista) of thickness 20 gauge and for every 01 RM length, provide 10 numbers stainless steel rings (Model No:- SS CRNG of Vista) 50 mm dia and proportionate for part there off, with stainless steel brackets ( Model:- SS 25 BR, Vista) near to ends with stainless steel finials ( Model:- SS-1 of Vista with adapter) for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

Supply and fixing of peg set of 4, brass chromium plated, fancy type, superior quality and fixing with screws complete all as specified and directed.

S&F of brass door magic eye as given specification material resin lens +zinc alloy,top diameter: 31.2mm, botom diameter approx 24mm, pipe diameter approx 16mm total length approx 50mm, inner height approx 36mm application 35 to 60mm thick viewing angle 200 degree of surrounding without opening the door unique design ultra clear view and superior finish, wide angle best in class lens for all round visibility the outsider cannot hide any ware, the back cover protects from the outsider observing any movements inside easy to instal with inbuilt screw over a wide range of door thickness from 35 mm to 60mm etc as required at site complete all as specified and directed.

Supply and fixing of solid chromium plated heavy duty door chain (weight not less than 249 gms) with brass screws to any type of door shutter and frame complete all as specified and directed.

M&L for Prepration of new steel surfaces and applying one coat of red oxide primer and two coat of synthetic enamel paint complete all as specified and directed.

M&L for 18/19mm thick Prelaminated particle board,ISI marked, exterior grade,prelaminated one side with decorative choice lamination & other side balancing white lamination,fixing of with screws rawal plug to timber frame work including all exposed edges with 6mm thick teak wood lipping and finish with french polish as in cupboards, kitchen cabinets,shelf etc complete all as specified and directed.

Supply and fixing of Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixing of complete all as specified and directed.

Supply and fixing of 40mm dia, cupboard knobs fixing with nut, screw and washer of brass, polished complete all as specified and directed.

Supply and fixing of hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixing with screws, Size of hasp and staple in mm 100 complete all as specified and directed.

S & F of Continuous (piano) hinges 30mm Width of flaps (when open) ,mild steel, bright finish or electrogalvanised complete all as specified and directed

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubing or conduit wiring, etc and making good, cutting not exceeding 10cm girth complete all as specified and directed

Cutting holes in brick walls built in cement mortar or cement lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required,Depth of embedded portion of hold fasts or lugs measured from the face of the jamb into the wall exc Half brick but not exc one brick complete all as specified and directed.

S & F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, etc. fixing with self tapping screws complete all as specified and directed.

S & F mild steel work in tubular trusses (framed) /rectangular hollow section, purlines and fastening including distance pieces etc. including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and directed.

M&L for two coats of synthetic enamel painting on steel surfaces of any description over 10 cm in width or girth not otherwise described new or previously untreated surfaces complete all as specified and directed.

Taking down eaves gutter and rain water pipe any size any pattern , PVC/ AC pipe including all fittings ,heads shoes, bends etc, Internal dia of pipe in 75MM/110mm complete all as specified and directed.

Supplied and fixed PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

Supplied and fixed PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

Supplied and fixed PVC (SWR) bends any radius 75mm dia all as specified and directed.

Supplied and fixed PVC (SWR) bends any radius 110mm dia all as specified and directed.

M&L for Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof suitable for 100mm dia pipe complete all as specified and as directed.

Dismantling of cast iron or reinforced concrtee drain pipes, jointed in cement mortar and taking out of trenches, if required Internal dia of pipe in 75mm/100mm complete all as specified and as directed.

Supply and fixing of sand Cast iron soil, waste and vent pipes ISI marked, in any length with or without ears with cement joints, laid in trenches or in floors bore of pipe 100mm complete all as specified and as directed.

Supply and fixing of sand Cast iron soil, waste and vent pipes ISI marked, in any length with or without ears with cement joints, laid in trenches or in floors bore of pipe 75mm complete all as specified and as directed.

Supply and fixing of sand Cast iron soil, waste and vent pipes ISI marked, in any length with or without ears with cement joints, fixing to walls bore of pipe 75mm complete all as specified and as directed.

All as per serial item No. 121 here-in-before 75mm thick fixed to walls :- old cast irom soil, waste and vent pipes any type retrieved from dismantling shall be used

Supply and fixing of sand Cast iron soil, waste and vent pipes ISI marked, in any length with or without ears with cement joints, fixing to walls bore of pipe 100mm complete all as specified and as directed.

All as per serial item No.123 here-in-before 100mm thick CI pipe above but except pipe note: - Old Cast iron soil, waste and vent pipes any type retrieved from dismantling shall be used).

M & L for Cast iron bends (ISI marked) (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 100mm, complete all as specified and directed.

M & L for Cast iron bends (ISI marked) (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 75mm, complete all as specified and directed.

Material and labour for Cast iron floor trap (ISI marked) of 75mm dia of outlet, plain with grating including jointing to waste pipe with solvent cement fixing in repair, and set in cement concrete 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) complete all as specified and as directed.

Supply and fixing of Articles n exc 5 kg each Cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire & soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters & similar articles complete all as specified and directed.

M&L two coats of black japan painting on new iron/steel surfaces of any description over 10 cm in width or girth not otherwise described including preparation of new surface complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, PVC/AC or Reinforced concrete) set in cement mortar,and taking out of trenches, if required, Internal dia of pipe in 75MM/100mm complete all as specified and directed.

S&F of PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F of PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

M&L for PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement fixing in cement concrete 1:2:4 complete all as specified and directed.

M&L for PVC (SWR) vent cowl 75mm dia complete all as specified and directed.

M&L for cutting Existing Steel tubing 50/40/25/20mm dia for alternations or additions (Each cut Measured )including threading of existing pipes placing new tee of required size tapping connection for new pipe line complete all as specified and directed. (cost should be inclusive of earth work)

Taking up or down 15mm bore, steel tubing and connection complete all as specified and directed.

Fixing only 15mm bore old Steel water tubing including cleaning of pipe all new galvanized fittings like elbow, tee, socket, bend etc and fixing to wall, ceiling or laid in floor complete all as specified and directed. Note: - Old Steel water tube/pipe any type retrieved from taking down shall be used along with all new GI fittings)

Supply and fixing of 15mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixing to wall, ceiling or laid in floor complete all as specified and directed.

Taking up or down 20mm bore, steel tubing and connection complete all as specified and directed.

Fixing only 20mm bore old Steel water tubing including cleaning of pipe all new galvanized fittings like elbow, tee, socket, bend etc and fixing to wall, ceiling or laid in floor complete all as specified and directed. Note: - Old Steel water tube/pipe any type retrieved from taking down shall be used along with all new GI fittings)

Supply and fixing of 20mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixing to wall, ceiling or laid in floor complete all as specified and directed.

S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing of cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supplied and fixed in repairs sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x460 mm and bowl size 410mmx330mmx 160mm complete all as specified and directed.

M&L for Stainless steel plate rack(Utensil Rack) of size (900mmx750mmx250mm ) made out of AISl 304 stainless steel 0.63 mm thick sheet fixing with brass screw of required size including necessary fittings/nuts,bolts & washers complete all as specified and as directed.

M&L in repair Stainless steel plate rack(Utensil Rack) of size (900mm x 750mmx250mm ) made out of AISl 304 stainless steel 0.63 mm thick sheet fixed with brass screw of required size including necessary fittings/nuts,bolts & washers complete all as specified and as directed.

S & F in repair 15 mm bore long body CP Bib taps cast copper alloy fancy type with capstan heads (chromium plated),and cup screwed down , high pressure for iron pipe complete all as specified and directed.

S & F of 15 mm bore CP Bib taps long body cast copper alloy fancy type with capstan heads (chromium plated),and cup screwed down , high pressure for iron pipe complete all as specified and directed.

Supply and fixing of Rotational moulded polyethlene water storage tanks of 500 ltrs capacity ISI marked (cylindrical vergical with closed top) triple layered hoisted and fixing in position all as specified in SSR Part I including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixing of. (Minimum weight 20mm-210 gms) including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

Supply and fixing of Rotational moulded polyethlene water storage tanks of 500 ltrs capacity ISI marked (cylindrical vergical with closed top) triple layered hoisted and fixing in position all as specified in SSR Part I complete all as specified and as directed.

S&F of Ball valves high pressure 20 mm of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixing of. (Minimum weight 20mm-210gms complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of water storage tanks of capacity exc 250 litres but not exc 500 litres complete all as specified and as directed. Note: While cleaning any float valve/tank cover,GI pipe to be removed and refixing of the same in position after cleaming of tank and incase of damaged during work shall be replaced by new without any extra cost to the department.

Supply and fixing in repair Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed.

Supply and fixing of Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed.

S&F of Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed.

S&F in repairs Vitreous China bowl type urinal flat back, size of 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe ,white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

S&F of Vitreous China squatting pan orissa pattern size 580 x 440 mm white with integral foot rests including provision of lime concrete bedding pvc flush 32mm dia suitable for low level flushing cistern and socket of WC pan complete all as specified and directed.

Supply and fixing in repair viterous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc. complete including making good to floor complete all as specified and as directed.

S&F Vitreous China wash down water closet pan including P or S trap (pedestal pattern), white or in matching colour of tiles (excluding flushing cistern and flush pipe) including plastic water closet seat, white or in matching colour , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device and wash down water closet complete all as specified and as directed.

S&F in repair PVC Coloured bathroom cabinet with looking mirror divided into shelf overall size 600mm x 450mm complete all as specified and as directed

S&F of 10 ltrs capacity PVC syphonic action type, flushing cistern, low level, white, with inlet,ball valve, float and handle including brackets, fush pipe of polyethylene of low or high density or PVC. 32 mm dia complete all as specified and directed.

Supplied and fixed in repairs 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets ,fush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specfied and as directed.

S&F Swivel shower of PTMT any colour for fixing with 15mm pipe (min. weight 40gms) complete all as specified and directed.

S&F of tubular towel rail,20mm dia D type brass chromium ,60cm long between flanges complete all as specified and directed.

S&F of angular stop cock, chromium plated with Chromium head and wall flange suiable for 15mm bore pipe fancy type complete all as specified and as directed complete all as specified and as directed.

All as per serial item No.165 here-in-before fancy type, chromium plated with long shank and cup (concealed type)

S&F of Vitreous China wash hand basin white flat back size 550mmx400mm including brackets & cutting for and pinning in ends of brakets or erecting stand complete all as specified and directed.

Supplied and fixed in repairs Viterous China wash basin, white, flat back, size 550x400mm excluding taps etc but including brackets,including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specfied and as directed.

S&F of Brass CP mixer for mixing hot & cold water screwed down for 15mm dia iron pipe and fixing complete all as specified and directed.

S&F of CP Pillar taps 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F of PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F of stainless steel Soap dish any type fixing to plugs with chromium plated brass screws complete all as specified and directed.

S&F of Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard & railing 60cm long complete all as specified and directed.

S & F in repair corner glass shelf with bracket fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

S&F of CP brass towel ring 20mm dia, fancy type, superior quality, fixing with and including chromium plated screws and wooden/plastic cleats complete all as specified and directed.

Supply and fixing in repairs 15mm bore CP Health faucet with flexible pipe not less than 90 cm long,PVC tube & wall hook, screwed for 15mm dia bore iron pipe complete all as specified and directed.

S&F of hat pegs coat hooks solid body 175mm to 250mm long cast iron or mild steel complete all as specified and directed.

M&L for Septic tank exc in ordinary soil PCC 1:2:4 typr B-I (20mm graded stone aggregate) in foundation and any other locations brick work in CM 1:4 all RCC work in M-30 (Nominal mix) for 10 users all as shown in drawing No. CEPZ/C-TD/013/13 Sheet No. 1/5 to 5/5 complete all as specified and directed.

M&L for Sockage wells exc in ordinary soil foundation in PCC 1:3:6 brick work in honey combing and solid wall in CM 1:4, all RCC work M-30 (Nominal mix) and filling with brick bats complete of size 1.20M dia X 3.0M deep all as shown in drawing No. CEPZ/C-TD/013/13 Sheet No. 1/5 to 5/5 complete all as specified and directed.

S&F of 150mm dia SGSW pipes laid in trenches with cement joints including PCC bed and packing under and haunching against sides of pipe after laid and tested in PCC (1:4:8) using 40mm graded stone aggregate and testing complete all as specified and directed.

M&L for unplastited drainage pipe 200mm dia type "B" with wall thickness 4mm(min) of pressure rating 8 KN/sqm laid in trenches and jointed with cement solvent including testing complete all as specified and directed including demolition and breaking up drain pipes in cement mortar including demolition of PCC bedding and hunching complete all as specified and directed

M&L for Concrete bed to drain pipes including packing under,and haunching against the sides of pipes after they are laid and tested in Cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate for Bore of pipe 200mm complete all as specified and directed

Cutting 20mm dia existing steel tubing for alterations or additions (Each cut measured) including threading of both end complete all as specified and directed

S&F of Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F of Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws etc. complete all as specified and directed.

S&F of 5.5mm thick Sheet glass, ordinary quality and glazing in square exc 0.5 sq.m in each pane for fixing in aluminium shutters complete all as specified and directed.

S & F of suspended false ceiling system using chicago metallic (E grid)exposed supended system, grid section size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions T-section 39 mm X 24mm X 0.8mm thick (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600mm length) Cross Tee of dimensions 29mm X24mmX0.8mm thick wall angle 22.2mmX22.2mmX 0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length)with and including 4mm thick HPSC(High pressure steam cured) pre-primed , self embossed . textured designer board, water resistant termite resistant , fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixing with steel dash through fasteners from purlins of the roof with butterfly clips(Wt-0.007 Kg/clip)hold down clips (Wt-0.0035 Kg/clip) complete all as specified and directed.

Material and labour for Cutting existing road mechanically including excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for crossing sewage line/drain pipe etc. not exc 10 sqm area on plan and not exc 1.5m in depth and getting out in any type of soil complete all as specified and directed. Note :1-Due care shall be taken while deciding pipe route for excavation. However any damage to Signal, BSNL, MES cable water/sewage pipe or any other service while excavation will be made good by the contractor and cost of the same for jointing material & labour is deemed to be included in this item. 2-The rates include for provision of red signals & flag to keep off traffic control and working during odd hours when traffic is light and proper barricade will be provided.

M&L 40mm thick PCC type B-1, (1:2:4) using 20mm graded stone aggregate finishing even and fair including Spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green as in floor for filling of road cutting surface complete all as specified and directed

M & L reinforced cement concrete pipes 450 mm bore, class NP3, laid and jointed complete with collars, complete all as specified and as directed.

Dismantling structural steel work including doors gates, grills but excluding framed truss etc.complete all as specified and directed.

Supplied and fixed Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled & countersunk for balusters running bars, for doors,balusters,nosing to steps including embeding in concrete & screwing etc. wind ties for roof including securing bolts; posts & struts in fencing/cooler stand including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., & similar work conforming to Fe 290-0 Gde E-165 complete all as specified and directed.

S&F in repair Mild steel, plain black sheet 1.25mm thick in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; waters tanks; water troughs; ducts; urinal troughs & funnels, etc. cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets & fixed to wood or steel members, etc., with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets,etc. as required

M&L for plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in copings, bed plates including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable punned down to 18 cm complete all as specified and directed. Note: Punned thick 18 cm will be measured for payment.

M&L for Brick covering with width equal to length of brick as mechanical protection to cable with well burnt sub class 'B' bricks laid complete all as specified and directed.

Supply and fixing of GI Tubing medium grade of 40mm nominal bore of pipe in trenches/under roads/ under culverts/under paths/under flooron walls/with pole in new position with screwed sockets joints together with all tube fittings (such as bend, elbow, tees, short places connections back nuts, dimnishing places, caps, plugs and union etc) complete all as specified and directed

M&L for XLPE insulated, armoured, heavy duty electric cable with aluminum conductor, 1100 volts grade, in replacement of cross-sectional area 16 Sqmm, 4 core including taking down of old UNSV/burnt electric cable complete all as specified and directed Note Earth work including excavation ,returning filling ,removing sand cushioning GI pipe brick covering for mechanical protection of cable etc will be measured and paid for seperstely under respective items of schedule .

Taking down old unserviceable copper/aluminium point wiring (light, fan, socket , power socket and bulk head fittings) on surface wiring on wooden batten/casings & caping complete, including fixture and fittings such as switches, ceiling roses,pendents holder, regulators and sockets by unscrewing carefully from boards etc and making good disturbed surfaces of walls, as per existing finishes complete all as spd and directed.

M & L for point wiring for one light/one fan controlled by one switch with 1.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable with and including PVC concealed conduit heavy duty 20 mm dia having thickness not less than 1.8 mm with all fittings including anodised pressed steel sunken box having thickness not less than 2mm with 3mm bakelite laminated sheet ISI marked for switches and sockets , including 1.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly, including cutting chiseling for concealed piping and making good disturbed surface to match with the existing surface complete all as specified and directed.Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green)(Make of 1.5 sqmm copper wire:

All as per srl item No 200 here-in-before but for 5 pin 5 amps socket outlet on independent board complete all as specified and directed.

All as per srl item No 200 here-in-before but for 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed.

All as per Srl Item No 200 here-in-above but for call Bell point complete all as specified and directed.

M & L for point wiring with 2.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable with in and including PVC concealed conduit heavy duty 20mm dia having thickness not less than 1.8 mm with all fittings including anodised pressed steel sunken box having thickness not less than 2mm with 3mm bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface finishing the surface to match with the existingsurface complete all as specified and directed.Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black,Earth- Green)(Make of 2.5 & 1.5 sqmm copper wire:

All as per serial item No. 204 here-in-before but using 4.00 sqmm PVC insulated unsheathed copper conductor multistrand flexible cable and 4 sqmm PVC insulated unsheathed multistrand copper conductor cable (green colour) as earth lead for geyser/ food warmer point complete all as specified and directed.

S & F of switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed.

S & F of switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed.

S & F of socket outlet 2 in 1, 5 pin 5 amps flush type 240 volts complete all as specified and directed.

S & F of socket outlet 2 in 1, 3 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S & F of lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

S & F of ceiling rose 65 x 50mm three terminals complete all as specified and directed.

Supply and fixing of ceiling fan regulator electronic socket type 5 stage speed variation ISI marked complete all as specified and directed.

S&F of sheet metal enclosure MCB distribution board single pole and neutral with a two pin and earth plug and socket 20 Amp 240 volts, complete with one single pole MCB of 20 Amp 10KA 'C' curve complete all as specified and directed.

S & F of LED smart Lamp, B22 type ,14 watt,complete all as specified and directed.

S & F of energy saving decorative LED box type with LED Rod 20 watt (4 Feet), 230 volts, 6500 K energy efficient tube light fitting extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories prewired and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings. (Note power factor should not be less than 0.95) complete all as spd and directed. Make of LED Rod:- CROMPTON LTT8-20 and Make of LED Fitting:- CROMPTON DMLN1LT8-16 or Technocommercially equivalent in any of the make mentioned in list of products.

M & L sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 6 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

M & L for MCB Single Pole 240 volts any rating from 20 to 40 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

M & L for MCB SPN 240 volts any rating from 6 to 40 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

Supply, fixing, testing and connecting the star rated ceiling fan 230 volts, single phase of 1200 mm sweep double bearing type with and including down rod, canopy cover etc and connecting with 3 core flexible copper conductor of 0.50 sqmm and including writing MES No. with black enamelled paint complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode , 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level)with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point , GI tubing 15 mm bore light grade protection pipe , GI watering pipe 20mm bore light grade with funnel and wire mesh , 15cm thick layer of charcoal & salt packed around the earth plate and PCC (1:2:4) pit and precast cover RCC 1:2:4 (Nominal mix ) reinforced with XPM having weight not less than 4 kg /sqm including suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover including earth work in any type of soil , removal of surplus soil to a distance n.exc 50m and connecting , testing on completion complete all as shown on electric plate No 03 of SSR -2009 Part I complete all as specified and directed.(Note: Excavation and earth work is deemed to be included in the rates quoted).

S&F sub Main Wiring with two single core PVC insulated unsheathed multistranded flexible copper conductor cable of size 2x6 sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor 4 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in and including not metallic PVC concealed conduit 20mm dia heavy duty complete and making good to disturbed surface of wall/floor with cement mortar and finishes to match existing surface all as specified and directed.

M & L for providing/ cutting the round/ square hole of required size in wall finishing the same for distrubed surfaces as per existing finishes complete all as spd and supply and fixing Plastic Ventillation fans, Single phase, 230 volts 150 mm sweep complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 1.5 sqmm copper cable from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as specified and directed.

S & F of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 4 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S & F of bldg secuirty light fitting energy saving high efficiency LED street light fitting 25 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 32 mm dia bent to shape having length not less than 1.5 mtr fixing with clamp etc and making connections using cord flexible 3 core copper cable of size 23/ .0076 from ceilling rose/ PVC connector to light fittingscomplete all as specified and directed. Make: CROMPTON CAT REF. LSTS-25-CDL or technocommercially equivalent in any of the make mentioned in list of products.

S & F of Bell AC,230 Volts, Single pole complete all as specified and directed.

S & F of Bell push flush type 5 Amp 240 volts complete all as specified and directed.

Taking down ceiling fan by disconnecting the electric connection and dismantling the blades and removing from ceiling/roof of bldg by descrewing the nut, bolt etc complete all as specified and directed.(Note-Old u/s balance ceiling fans will be deposited in Store yard)

Rehanging only of ceiling fan and connecting up including provision of PVC insulated and overall sheathed flexible copper conductor cable 3 core of size 0.50Sqmm from ceiling rose or connector to fan including minor repairs such as replacement of locking pin, reel insulators, bolts, nuts etc and spraying one coat of synthetic enamel paint of required colour complete all as specified and directed.

Supply and Fixing in replacement LED Bulkhead 10 watt all as specified and directed by Engr-in-charge. Make :- Crompton Cat Part No:- LBHP-10-CDL or equivalent in any of the make mentioned in list of products.

S & F in replacement energy saving decorative LED box type 20 watt (4 Feet), 230 volts, 6500 K energy efficient tube light fitting extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories prewired and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings. (Note power factor should not be less than 0.95) complete all as spd and directed. Make of LED Rod:- CROMPTON LTT8-20 and Make of LED Fitting:- CROMPTON DMLN1LT8-16 or Technocommercially equivalent in any of the make mentioned in list of products.

S & F in repair energy saving LED Rod 20 watt (4 Feet), 230 volts, 6500 K energy efficient tube light complete all as spd and directed. Make of LED Rod:- CROMPTON LTT8-20 or equivalent in any of the make mentioned in list of products.

M & L in repair sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

M & L for MCB in repair Single Pole 240 volts any rating from 20 to 40 amps, with rupturing capacity 10 KA, 'C' curve including providing thimble for out going cables complete all as specified and directed.

M & L for MCB in repair SPN 240 volts any rating from 6 to 40 amps, with rupturing capacity 10 KA 'C' curve, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement sub Main Wiring with two single core PVC insulated unsheathed multistranded flexible copper conductor cable of size 2x6 sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor 4 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in and including non metallic PVC concealed conduit 20mm dia heavy duty complete and making good to disturbed surface of wall/floor with cement mortar and finishes to match existing surface all as specified and directed including taking down of existing un serviceable sub main wiring complete.

S & F in replacement bldg secuirty light fitting energy saving high efficiency LED street light fitting 25 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 32 mm dia bent to shape having length not less than 1.5 mtr fixing with clamp etc and making connections using cord flexible 3 core copper cable of size 23/ .0076 from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage. Make: CROMPTON CAT REF. LSTS-25-CDL or technocommercially equivalent to any of the make mentioned in list of products.

S & F in replacement of old unsv sheet metal enclosures distribution boards, double door three phase 415 volts 4 ways vertical TPN DB for comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following (a)MCCB FOUR POLE 100 AMPS AC 415 VOLTS 25 KA=01 NO as incoming and 12 nos. MCB SP 40 Amps, C series as outgoing (Note :- (i)The DB shall be VTPN series of Schenieder Cat Part No:- A9HVD04L or equivalent in any of the make mentioned in list of product . (ii) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(iii)connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped.(1v) all the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) double continuous earth wire shall be provided for each three phase DB from earthing mains dolly

Supply and laying of XLPE insulated, armoured, heavy duty electric cable with aluminum conductor, 1100 Volts grade, of size 25 Sqmm 4 core and taking down of old unservicable /brunt electric cable complete all as specified and directed. Note:- Earth work including excavation, returning filling , removing, sand cushioning, GI pipe,brick covering for mechanical protection of cable etc will be measured and paid for separately under respective items of schedule.

Supply and fixing in replacement of GI tubing medium grade of 40 mm nominal bore of pipe in trenches/under roads/ under culverts/under paths/under floor/on walls /with pole in new position with screwed sockets joints, together with all tube fittings (such as bends, elbow, tees, short places connections back nuts, diminishing places, caps, plugs and union etc) complete all as specified and directed .

Notes :- (a) The contract sum shall be arrived at after deduction of amount of Schedule of Credit. (Rs. 57,333.00). (b) PERFORMANCE SECURITY :- (Refer condition 19 of IAFW-2249) The performance security for an amount equivalent to 5% (Five percent) of the accepted contract sum shall be delivered by the successful bidder immediately after the date of intimation letter of acceptance and all provisions shall be applicable as per condition 19 of IAFW 2249

Ambika Construction Co

M/S SALARIA BUILDERS