SPL REPAIR OF TOILETS AT BLDG NO P 04 OF HQ TG EME UNDER AGE BR III ADDN ALTN TO 6 X BATHROOM IN BLDG NO P 263 OFFRS MESS AT 422 FD HOSP PROVN OF GARBAGE ROOM AT DCN SUB GROUP PALAM PROVN OF 08 X WATER GEYSERS 25 LTRS FO

Amount

Demolition of cement concrete (unreinforced)/lime concrete/sunken floor of any description and in any position not otherwise specifically provided for by mechanical means (like drill machine, Hilti, pneumatic chisel, etc) complete all as spd & directed.

M&L PCC 1:5:10 Type E-2 (using 40 mm graded stone aggregate ) in mass concrete for sunken portion of WC, complete all as specified and directed.

M & L for Water proofing treatment of sunken RCC slab : (i) 15mm thick plaster in CM (1:3) mixed with WP compound as per manufacturer's instructions shall be provided on sunken portion while the concrete is green. (ii) Apply cement slury @ 0.488 kg/sqm cement mixed with Acrylic based polymer modified cementious composite compound @ 0.253 kg/sqm and the surface will be allowed to air cure for 4 hours. (iii) Apply another layer of cement slurry @ 0.242 kg/sqm of cement mixed with Acrylic based polymer modified cementious composite compound @ 0.126 kg/sqm and the surface will be allowed to air cure for 4 hrs. (Make of cement composite compound of Dr. Fixit/Fosroc/Sikka) (iv) Curing the sunken portion with water minimum for 48 Hrs by ponding. (v) Paste 200micron thick poythene film of approved make with approved adhesives to the treated sunken surface. (vi) Joints/Traps/WC/Soil pies shall be properly sealed with approved sealing compound of approved make. (vii) Testing of all traps & joints shall be done after sealing and before filling of sunken slabs. (viii) Spout pipe shall be provided for drain out the water in sunken portion. Note : Flat surface shall be measured for payment.

Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars etc but excluding ashlars facings dressed stone work and Precast concrete articles, complete all as sfd and directed.

M&L for Brick work with Sub class 'B' bricks having compressive strength not less than 100kg/sqcm straight or curved on plan to any radious in half brick thick walls, built in Cement mortar 1:4 complete all as specified and directed.

M&L for Brick work with Sub class 'B' bricks straight or curved on plan exceeding 6m mean radius, built in Cement mortar 1:6 complete all as specified and directed.

M&L for 15mm thick rendering of ready mix mortar of approved make on brick work or concrete surfaces on walls, finish the surface even and smooth without using extra cement as complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls applying damp proof wall care putty 1mm on wall even and smooth surface and applying two coat of oil bound distemper over a coat of alkali primer (of approved quality and tint) on wall using painting roller, complete all as specified and directed.

Taking down cement plaster from stone/brick walls including racking out joints for keys and scrubbing down with water etc, complete all as specified and directed.

M&L for 5mm thick rendering of ready mix mortar of approved make on fair face on ceiling and finished even and smooth without using extra cement complete all as specified and directed.

M&L for three coats of White wash including preparation of new plastered undecorated surfaces on ceiling complete all as specified and directed.

M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified (Payment for providing grooves shall be included in the quoted rate.)

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

Taking down chowkats or frames not exc. 1.5 sq. m with shutters (without taking off shutters from the frames) , complete all as specified and directed.

S&F in repairs door closer hydraulically regulated of aluminium (extruded section) , designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 complete all as specified and directed.

S&F solid PVC Door Frame of size 50mm x 95mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid Panel PVC moulded door shutter, 30mm thick (style) consisiting of frame made out of MS tubes for top and bottom rails. M.S. frame shall covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail, bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing including fittings complete all as specified.

S&F SS Butt hinges type C-11 100 mm long for PVC doors complete all as specified.

S&F aluminium anodized extruded bow handle fabricated type 125mm long complete all as specified.

S&F 200mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, top hung and with provision of louvers without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

Dismantling of floor, hearth or wall tiling including cement mortor bedding (but not backing removing serviceable to store and rubbish off the premises complete all as specified and directed.

M&L for 40 mm thick cement concrete type B0 (1:2:4) using 12.5 mm graded stone aggregate as in sub bases complete all as specified.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc set and joined in neat cement slurry and pointed in white or colour cement to match colour tiles including 15 mm thick screed bed in CM 1:4 complete all as specified & directed.

M&L for Glazed ceramic coloured tiles in vertical surface 7 to 8mm thick size exc 0.11sqm but not exc 0.18 sqm set and jointed in neat cement slurry and pointed in white or colour ement to match including 15mm thick screed bedding/backing in CM 1:4 complete all as specified & directed.

M&L 18-20mm thick black granite of size in single pieces with full width of wall (tabled rubbed, polished and moulded) as in columns, steps, window cills and like laid over 15mm screed bed or plastering in CM 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with the shade of granite including dismantling of stone slab complete all as specified and directed.

S&F in repair grating doom 100 mm dia of CP complete all as specified and directed.

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified & directed.

Supplying and laying of 20 mm external dia CPVC pipes SDR 11 & Plain CPVC SDR 11 with all plain and brass fittings in trenches/ walls including dismantling old GI pipes including cleaning for refixing or removal to store complete all as specified and directed.

Supplying and laying of CPVC pipes 25mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all brass and plain fittings including dismantling old GI pipes complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls fixed with MS clamps and shoe at ground level complete all as directed.

S&F110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls fixed with MS clamps and shoe at ground level complete all as directed.

M&L for PVC (SWR) multi floor trap of 100mm dia,plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

S&F 110mm PVC (SWR) bends any radius complete all as specified & directed.

S&F 75 mm PVC (SWR) bends any radius complete all as specified & directed.

S&F PVC (SWR) 75/110 mm junction single/double, (double T), equal or unequal complete all as specified & directed.

S&F PVC (SWR) 75/110 mm branch piece, single (single Y) equal or unequal complete all as specified & directed.

S&F PVC (SWR) 75/110 mm vent cowl complete all as specified & directed.

Supply and fix for 100 mm dia cast Iron trap 'P' or 'S' type (fixed with lead joints) with grating including jointing to waste pipe fixed in cement concrete type B1 complete all as specified and directed.

S&F 19mm thick Prelaminated particle board, inferior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screw to timber frame work all as specified and directed.

Supply and fix in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as directed. Make ; Cat no CAN-1173 or Kohler /Marc of Equivalent catpart .

Supply and fix in repairs chromium plated single tubular towel rail 20mm dia, D type 60 cm long between flanges, including a pair of CP brass brackets complete all as specified and directed. Make : Jaquar Cat No ACN-CHR-1111N or Kohler /Marc of Equivalent catpart .

Supply and fix in repairs chromium plated shower rose with shower arm rod complete all as specified and directed. (Make-Hindware Cat No F-160052 /JAQUAR/MARC).

Supply and fix in repairs 15 mm dia wall mixer , chromium plated brass fancy type with all connection sleeves, capstan head, scrwed down complete all as specified. Make-Hindware JAQUAR/ /MARC) .

Supply and fix for soap dispensor with glass bottle all as directed. (Make: jaquar cat no CAN-CHR-1135N ) or Kohler /Marc of Equivalent catpart .

Supply and fix for soap dish all as directed. (Make: jaquar cat no CAN-CHR-1131N ) or Kohler /Marc of Equivalent catpart .

S&F in repair vitreous china wash hand basin, white flat back, size 580 x 450mm excluding taps, waste pipe chain and plug and porcelain but including brackets, waste coupling complete all as specified and directed.

S&F counter top vitreous china wash hand basin, oval/circular shaped excluding taps, waste pipe chain and plug and porcelain but including brackets, waste coupling complete all as specified and directed. MAKE :- CERA, Jaquar, HINDWARE etc

S&F Vitreous China urinal of size 465x355x265 mm, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified & directed.

S&F Vitreous China urinal with electronic flushing system, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified & directed. Make Catpart No:- CERA B2050109 HINDWARE 60018

S&F Urinal spreader of CP any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) ® complete all as specified & directed. Make :- CERA, Jaquar, Kohler, Marc & ESS etc

S&F in repairs Two way Bib cock, fancy type chromium plated cast copper alloy with capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed complete in all respect as specified. Make :- CERA, Jaquar, Kohler, Marc & ESS etc

S&F Health Faucet mild steel chromium plated suitable for 15 mm dai pipe with 1.25 mtr long flexible tube and wall hook including making connections and fixed in position complete in all respect as specified. Make :- CERA, Jaquar, Kohler, Marc & ESS etc

S&F Brass CP mixer for mixing hot & cold water (for wash hand basin) and fixed including dismantling of 15mm dia chromium plated pillar tap, complete all as specified and directed. Make :- CERA, Jaquar, Kohler, Marc & ESS

S&F mirror 600mm X800mm 5 mm thick with double coat for protection and longevity having 3 shelves with clear 5 mm and stainless steel rails silver plating on back for better reflection complete all as specified and directed. Make :- CERA catpart No. B3510144 , Kohler Catpart No. 26052-BGL

S&F in repair vitreous china single piece WC with softclose seat cover (PP), brass higes, fixing assessories set, cistern fittings, traps distance (MM) S-110, complete all as specified and directed (Make : Jaquar Cat Part No. SLS-WHT-6851S110PP, CERA Cat Part No. S1013222, HINDWARE CatPart No. PEARL S-300.

S&F in repair European vitretious china wash down water closet pan (excluding flushing cistern but including flush pipe and pvc seat cover white) complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

M & L for chromium plated bottle trap (with internal partition ) 32mm size with 250mm and 190mm long wall connection pipes & wall flange complete all as specified and directed. Make : Jaquar or equivalent of Marc/Ess

S&F in repairs 32/38 mm PVC waste pipe 900 mm long with complete all as specified.

S&F flushing cistern 10ltr capacity syphonic action type low clevel with inlet ball valve ,float valve and handle including bracket etc. complete all as directed.

S&F 15mm dia bib taps, cast copper alloy chromium plated with capstan head fancy type,screwed down,screwed for iron pipe or for brass ferrule and fixed all as specified.

S&F 15mm dia concealed Stop valves/stop cock, male or female cast copper alloy chromium plated, screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe on for unions all as specified.

S&F in repairs 15 mm bore angle valve, cast copper alloy screwed down high pressure with capstain head with long shank & cup complete all as specified & directed.

M&L in repair rotational moulded polythylene water storage tanks1000 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified including 20 mm brass valve high pressure with polythene float and fly nut complete and GI tank nipple, screwd for iron pipe complete all as specified and directed.

S&F in repair 100mm dia CI bends or diminishing pieces fixed to wall/floor complete all as specified and directed.

S&F in repair100mm Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or fixed to wall in repair complete all as specified and directed.

S&F 100mm bore CI vent cowl complete all as specified and directed

S&F 100mm bore CI tee, Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F for 100mm bore dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/window or other frames/chowkats of size 45x70mm comprising of vergin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk/ wheet husk) and non toxic additive etc all as per SSR 2020 part 2 ser No 08100A. complete all as specified and directed

S&F Factory made single extruded WPC (W) solid decorative type flush door shutter of size 30mm thick comprising of vergin polymer of K value 58-60 (Suspension grade ), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non toxic additive etc all as per SSR 2020 part 2 ser No 08105C. complete all as specified and directed.

S&F in repair aluminium anodised barrel tower bolt 150 mm size of extruded section complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed..

S&F stainless steel butt hinge medium weight 100 mm size complete all as specified and directed.

M & L for providing and fixing of 10 mm thick plaster of Paris ceiling with sunk or raised moulding as ordered (Gypsum anhydrous) to flat wooden surface or metal frame work and reinforced with GI wire mesh complete all as specified and directed.

S&F false ceiling with powder coated GI grid of size 600x600 mm using main Tee of size 24x28x0.40mm prepunched to accept cross tee of size 24x28x0.40mm and wall angles of size 25x25x0.40mm fixed with wall around of size with and including 4mm thick fiber cement board white colour designer tiles as approved by GE of size 595x595 mm placed in the grid and held in position duly suspended by 4mm dia GI wire hanger from the roof with holding down clips, butter fly clips and necessary provision for light fixture etc complete as per manufacturers instructions complete all as spd & directed including dismantling old false ceiling any type complete all as specified and directed.

M&L for preparation and applying two coats of OBD over one coat of primer including application of 1mm thick wall care complete all as specified and directed.

S&F aluminium anodised louvered ventilator with 4 mm thick pin headed glass and 100 mm wide glass strips, white framed and fixed with aluminium anodised frames etc including taking down existing old window of any description complete as specified and directed.

Surface excavation n exc 30cm deep and averaging 15cm deep including getting out in hard/dense soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base flooring complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade including 25mm thick sand bedding complete complete all as specified and directed.

M&L for mild steel work with square/rectangular section in post, Roof trusses (framed), trussed, purlins, rafter, crane gantries, wind ties, rails and fastenings and heavy bracket, framing of tube sections including distance pieces, cleats, MS plates, nut & bolts etc complete all as specified and directed.

M&L for preparation of new steel & iron surfaces of any description over 10cm in width or girth not otherwise described and applying two coats of syntethic enamel paint over a coat of red oxide primer complete all as spd & directed.

S&F pre-painted galvatume aluminium zinc coated (150GSM) GI based corrugated steel sheet 0.50 mm thick of (Green) colour as approved by GE having tensile strength of 550Mpa as in roof covering, ridge, fixed with self tapping screws complete all as spd & directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surface, 6 to 7 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.18 sqm, in patch work set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed bed/backing in CM 1:4 including complete all as specified and directed.

M&L for Preparation of new surfaces (Plastered or un-plastered) of walls and applying two coats of cement based paint white or tinted ,complete all as specified and directed .

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work complete all as specified and directed.

S&F 1.60mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

S&F Welded steel wire fabric complete to wood or steel members n.exc 4kg per sqm complete all as specified and directed.

M & L for 25 mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) as in sub floor of floor finishes, finished even and rough complete all as specified and directed.

M&L for wooden flooring is made of Maple wood 20mm thick, 56-100 mm wide laid over wooden runners 35mm x60mm which rest on 11mm rubber air pads, which is turn rest on a PE moisture barrier. The Maple wooden pieces are jointed together in a tongue and groove fashion. Nailing is done on the tongue of the plank, so that the nails are not exposed. The runner are Deodhar/pine wood. The wood may be varying width and length but each line will be of the same width. All wood will be anti-termite treated. The runner are laid horizontally across the court from wall to wall and rubber cushions are fixed under them complete all as specified and as directed.

M & L for light shade or printed vitrified ceramic tiles 9 to 10mm thick (square/rectangular) polished, area of each tile n. exc 0.36 sqm in floors, steps (treads and risers) etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed.

M&L for powder coated Anodised aluminium frame for doors, windows, ventilators, grill, partitions with one or more rebates including joining cleat for fixing etc. complete all as specified

M&L for powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing,(handles 2 Nos in each door, 15mm aluminium hinges-3 Nos each door, 15mm Aluminium tower bolt 02 Nos each door), anodised aluminum snap beading screws etc. complete all as specified.

M&L for complete removal of old treatment and preparation of old plastered surfaces of walls and applying two coats of plastic emultion paint over a coat of 1 mm thick wall care putty to bring uniform surafce complete all as specified.

M&L for preparation of old treated surfaces of ceiling and applying one coat of oil bound distemper complete all as specified and directed (Note :- Height of building upto 04 storey)

M&L for cutting upto a depth of 15cm into cncrete walla and trimming surface as required,girth exc.30cm complete all as specified and directed.

Taking down carefully copper/aluminium any type of point wiring (light/fan/socket /power) complete (fittings such as switches, ceiling roses, holders, sockets,regulators light fittings) and making good the disturbed surfaces of wall/floors/ceiling etc) complete all as specfied & directed.

Material and labour for concealed point wiring with PVC insulated unsheathed multistranded colour code copper conductor in PVC conduit with FRLS cable1.5 Sqmm size 1100 volts grade conforming to IS:694 in new modular metal flush box of 1.6 mm thick including one coat of synthetic enmelled black paint and providing modular white cover plate with frame of suitable size of required colour fixed with brass screws and cup washers including single core stranded FRLS copper conductor 1.5 Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit all as specified and directed by Engr-in-charge for the following :- (a) One light/fan/bell point controlled by one way switch 5 amps.

(b) One 3 pin 5 Amps socket outlet point controlled by one way switch on independent board.

(c) One 3 pin 5 Amps socket outlet point controlled by one way switch on same board.

Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded FRLS copper conductor in PVC conduit with cable 2.5 Sqmm size 1100 volts grade conforming to IS:694 in new modular metal flush box of 1.6 mm thick including one coat of syenthetic enamelled black paint with new modular white cover plate with frame of suitable size of required colour fixed with brass screws and cup washers including single core stranded FRLS copper conductor 1.5Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit for One 3 Pin socket 15A/modular AC box Indepentent board

S&F Modular switch 1 way 6 A,1 module complete all as specified and directed.

S&F Modular switch 1 way 16 A,1 module complete all as specified and directed.

S&F of Modular socket outlet 6 A, 2/3 pin, combined 2 module complete all as specified and directed.

S&F of Modular socket outlet 16 A, 2/3 pin, combined 2 module complete all as specified and directed.

Material and labour for concealed point wiring with PVC insulated unsheathed multistranded colour code copper conductor in PVC conduit with FRLS cable1.5 Sqmm size 1100 volts grade conforming to IS:694 in box of 1.6 mm thick including one coat of synthetic enmelled black paint and providing with brass screws and cup washers including single core multi stranded FRLS copper conductor 1.5 Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit all as specified and directed by Engr-in-charge for the following :-(a) One light/fan/bell point controlled by one way switch 5 amps.

(b) One 3 pin 5 Amps socket outlet point controlled by one way switch on independent board.

(c) One 3 pin 5 Amps socket outlet point controlled by one way switch on same board.

Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded FRLS copper conductor in PVC conduit with cable 2.5 Sqmm size 1100 volts grade conforming to IS:694 in new metal flush box of 1.6 mm thick including one coat of syenthetic enamelled black paint fixed with brass screws and cup washers including single core multi stranded FRLS copper conductor 1.5Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit for One 3 Pin socket 15A Indepentent board

S&F of switch piano type 5 amps single pole one way complete all as specified and directed.

S&F of switch piano type 15 amps single pole one way complete all as specified and directed.

S&F of socket outlet multipurpose 2/3 pin 5 amps flush button type complete all as specified and directed.

S&F of socket outlet multipurpose 2 in 1, 5 and 15 Amps complete all as specified and directed.

S&F of single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 including taking down old MCB's complete all as specified and directed.

S&F of SPN MCB 32 amp, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘C’ curve, 10 KA breaking capacity, complete all as specified and directed.

S&F of SPN MCB 40 amp, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘C’ curve, 10 KA breaking capacity, complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.complete all as specified and directed.

Supply and fixing LED lights fitting 1x 12W (2 feet length), 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.complete all as specified and directed.

Supply only ultra bright compact 12 W LED downlighter (round or squrae shape) with high efficiency LEDs ideally suited for low ceiling areas to give glare free light, complete all as specified and directed.

Taking down exhaust fan, sealing cable end, dismantling blades and removing fan and blades and deposit to MES store complete all as specified and directed.

Supply & fix exhaust fan made up of sturdy engineering plastic complete with louvers shutter, voltage 230 V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed.

S&F ceiling rose 3 phase/PVC/polycarbonate isolated body complete all as specified and directed.

S&F electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV,connection pipe incl all PVC & CP connections all as directed.

S&F bib taps 15mm fency type with crutch or butterfly handle, screwed down screwed for GI pipe complete all as specified and directed.

S&F stop valve 15mm fency type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for GI pipe complete all as specified and directed.

S&F GI tubing pipes galvanized, "Medium class", supplied and laid complete including fittings 15 mm (1/2") dia complete all as specified and directed.

Cutting of Existing water supply main any size upto 25 mm for Taking branch connection for taking branch connection of size 15 mm including insertion of Tee unegual all as required at site or directed.

M&L for modular AC Box with 20A SP mini MCB,Plastic enclosure & unbreakable Heavy Duty ISI mark Plug Top complete set dully concealed in wall complete all as specified and directed.

S&F of factory made epoxy polyester powder coated distribution board TP & N 4 way (VTPN MCCB DB) with metal double door (IP-54 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with provn for DPX 160, 4 pole MCCB and ELM as incommer and 12 SP MCBs outgoings complete all as specified and conforming to IS: 8623 along with cable end box for above DB including taking down old DBs all as specified. NOTE :- (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F in replacement MCCB 4 pole 125 Amp, Icu = 16 KA, 415 volts, 50 Hz, type with thermal magnetic release duly connected with copper spreader links 04 Nos and proper size of lugs, nuts bolts and washers for proper connections all as specified and directed.

S&F of factory made epoxy polyester powder coated distribution board SP & N 8 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 6 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 alongwith cable end box for above DB all as specified and directed. NOTE (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

Supply and fixing ceiling fans complete with blades, down rods, regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fixing in repairs energy saving environment frindly & robust highbay LED light with PDC housing suitable for Ceiling(Surface/Suspended) mounting IP 65 protected luminaire of capacity 150 watts, ( 22500 System Lumens ) with efficacy >150 lm/W, Wide voltage operating range of 140 V - 270 Volts & Wide temperature operating range: -10 °C to +50 °C & Surge Protection Upto 10 kV complete all as specified and directed

Deduct Credit: for demolished/dismantled material of (-) Rs 84025.00 (Minus) as listed in Schedule 'A' Part II (Credit Schedule) Note: Tenderer's shall not quote against this item. The amount of Credit Schedule is tentative, however the same shall be considered to arrive at the contract sum

POONAM ENTERPRISES