SPL REPAIR TO BLDG NO P-62H (OR LIVING ACCN) AND BLDG NO T-06, FRESH STORES AT FSD POONCH AND BLDG NO T-36, P-49B AND P48B ORs BATHROOM AND TOILET BLOCK FOR 237 FD WKSP COY EME AT POONCH UNDER GE 881 EWS

Amount

B/R Portion: -Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

Dismantling timber scantling under 40 sq cm in section in any position, framed work in fillets, rails, posts, rafters, purlins, etc complete all as specified and directed.

Dismantling plain or corrugated, semicorrugated, Plain etc. sheets in roof coverings including nainital or similar pattern complete all as specified and directed.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets omplete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar omplete all as specified and directed.

Demolition of cement Concrete is ground floors and pavings n exc 15 cm thickness (below or above ground level) including old polymeric membraneomplete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar omplete all as specified and directed.

Taking down cement plaster on brick or stone wall including raking out joints hocking for key scrubbing down with water etc omplete all as specified and directed.

Taking down chowkhats without taking down shutters n exc 1.5 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1.5 sqm but not exc 4 sqm complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) of any description exc 1.5 sqm but not exc 4 sqm complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in Ridge, fixed with self tapping screws complete all as specified and directed.

Clean swan second class hardwood in scantlings,in repairs, to replace old and decayed timber (including piecing, scarfing, etc., of old and new timbers if required) and removing defective portions to store complete all as specified and directed.

All as per items No 14 above but except timber complete all as specified and directed.

PCC 1:2:4 type b-1 cills, steps; seismic and other similar bands, plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones,bed plates, kerbs not provided for in Item 04028 of SSR-Pt -II, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

Walling of random rubble stone masonry, brought up to course, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed.

All as per items No 17 above but except stone complete all as specified and directed.

Rendering 20 mm thick on stone masonry wall or concrete surface in CM 1:6, finished even and smooth without using extra cement complete all as specified and directed.

Rendering 20mm thick on stone masonry wall or on other htan fair faces of brick work/concrete surface in CM 1:4, finished even and fair complete all as specified and directed.

75 mm thick cement concrete (1:3:6), type C-2 using 40mm graded stone aggregate as in floors, hard standing etc and laid in alternate bays complete and finished the even & fair and providings joints through out the thickness of plinth protection filed with mastic filling comprising one part of 01 bitumen Vg 20 grade and three part of sand by weight all as specified and directed.

Two coats of Oil bound distemper on new/old surface over and including a coat of alkail resistance primer and including preparation of surface complete all as specified and directed.

Complete removing of existing treatment and preparing old plastered or unplastered surfaces of walls and applying two coat of distemper oil emulsion complete all as specified and directed.

Preparation of new plaster or un-plastered surfaces of walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10sqm over new surfaces on walls complete all as specified and as directed.

Two coats of synthetic enamel paint over and including a coat of pink primer on new wooden surfaces over 10 cm in width or girth including preparation of new or previously untreated surfaces of wood complete all as specified and directed.

One coats of synthetic enamel paint on old wooden surfaces over 10 cm in width or girth including preparation of surfaces of wood complete all as specified and directed.

Mild steel work conforming to Fe-290 Gde E-165 in wind ties for roof, posts and struts including cutting top to shape as directed, drilling holes and fixed with L or J type cranked hook bolts complete all as specified and directed.

Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed using IInd class hard wood (Sal/Hollock) complete all as specified and directed.

Cutting holes in stone walls exc half bricks but not exe. one brick in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required:hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains;hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee pieceinserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats using second class hard wood complete all as specified and directed.

2nd class hard wood 35 mm thick plain framed, panelled shutters (any number of panel). with panels of timber flat on both sides (feather edged), or of vennered particle board medium density, wood particle board with commercial face veneers; fitted to chowkats complete all as specified and directed.

30 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (b); supplied and fitted to chowkats using second class hard wood for windows complete all as specified and directed.

3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sq.m in each pane complete all as specified and directed.

3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square nexc 0.5 sq.m in each pane including hacking out old glass complete all as specified and directed.

Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S & F in repair galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

Butt hinges 75 mm long, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

Butt hinges 100 mm long, medium weight, cold rolled mild steel, and fixed complete all as specified complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

Aluminium, anodised, barrel tower bolt of 150mm long bolts of extruded section complete all as specified and directed.

Aluminium, anodised, barrel tower of 75mm long bolts of extruded section and fixed complete all as specified and directed.

Aluminium, handle cast type anodised,150mm long complete all as specified and directed.

Aluminium, handle cast type anodised,100mm long complete all as specified and directed.

Position suspended false ceiling using E- grid suspended ceiling grid system of grid size 600x600mm with GI frame work of main runner 38 x 24mm sheet thickness 0.4mm, cross Tee 28 x 24mm sheet thickness 0.3mm and wall angle 24 x 24mm x 3mm using 4mm thick high pressure stream cured classic variant E-board, designer pattern (ISI marked, IS No 14862-2000) fibre cement E board to be placed in the grid suspended by 4mm GI wire hangers from the purlins of the roof with butter fly clips including preparation of surfaces and applying two coats of synthetic enamel paint over one coat of primer complete all as specified and directed.

Machine cut kota stone slab flooring 180to 20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and screed bed 20mm thick in CM 1:4 complete all as specified and directed.

Machine cut kota stone slab 18 to 20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed including rubbing and polishing with 10mm thick rendering in CM 1:4 complete all as specified and directed.

Grinding, cutting, polishing and rubbing to kota stone slab floor and filling grey cement slurry mixed with pigment to match the shade complete all as specified and directed.

Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

25mm thick PCC (1:2:4) type B-0 with using 12.50 mm graded stone aggregates as in sub base/levelling course of flooring, finished even and rough to receive the top layers complete all as specified and directed.

25mm thick chequered cement concrete tiles, of size 30cmx30cm, set and jointed in neat cement slurry including 20mm thick screed bed and pointed in white or coloured cement mixed with mixture of pigments to match with the colour of tiles complete all as specified and directed.

75mm thick PCC (1:4:8) type D-2 with using 40mm graded stone aggregates as in sub base to receive the top layers complete all as specified and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe.290 Gde E-165 complete all as specified complete all as specified and directed.

Two coats of synthetic enamel paint over and including a coat of red oxide primer on steel surfaces over 10 cm in width or girth including preparation of new or previously untreated surfaces of steel surface complete all as specified and directed.

Hollow PVC Wall Lining consisting of 5mm thick PVC sheet of plain colour sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

5mm thick PVC sheet fillet of width 35mm for wall paneling includingusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed.

18 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

Stainless steel handles 200mm long fixed to wooden shutters complete all as specified and directed.

Magnetic catchers fixed in cabinets with screws complete all as specified and directed.

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flap 30 mm complete all as specified and directed.

Rolled mild steel works as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to grade. Fe-410-W(Gde-E-250) quality-B complete all as specified and directed.

Material & Labour for complete removing of existing treatment and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces in painting on walls complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises complete all as specified and directed.

Glazed coloured ceramic tiles of size 450x350x7 mm thick as in vertical surfaces such as skirting, dados/repairs to step, set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the colour of tiles including 15mm in CM 1:4 rendering as backing coat etc complete all as specified and directed.

100mm thick PCC 1:4:8 type D-2 (40mm graded agg) as in sub base, finished even and fair complete all as specified and directed.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade complete all as specified and directed.

Sand filling as in cushioning below interlocking paver block complete all as specified and directed.

Demolition of RCC any descripation and any postion not otherwise specifically provided complete all as specified and directed.

RCC type B0 1:2:4 (12.5mm graded aggregate) as in lintel beam, Chajjas complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.fair finished surface complete all as specified and directed.

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) ot less than 0.9mm dia or securing with clips, complete all as specified and directed.

All as per item No 71 above but 8mm to 10mm dia bars in stirrups, spacers and binders complete all as specified and directed.

Anodised aluminium frame for doors, windows, ventilators Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

Anodised aluminium. door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified complete all as specified.

Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

Sheet glass, 5.5 mm thick ordinary quality and glazing Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers exc 0.5 sq. m in each fixed in door and window complete all as specified and directed.

Prelaminated particle board 9mm thick, interior grade, prelaminated both side with decorative choice lamination & other side balancing white amination, fixed with screws to aluminium frame complete all as specified and directed.

Sheet glass, ordinary quality, 4 mm thick and glazing with oil putty or wooden beads, in square n exc. 0.5 Sq.m pane, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks triple layers (Cylindrical vertical with threaded closed top) hoisted and fixed in position all as spd in SSR Pt-I, capacity in 500 Ltrs including dismantling existing water tank and removing to store, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks triple layers (Cylindrical vertical with threaded closed top) hoisted and fixed in position all as spd in SSR Pt-I, capacity in 1000 Ltrs including dismantling existing water tank and removing to store, complete all as specified and directed.

Non skid ceramic coloured tiles of size 400x400x7mm thick in floor etc set & jointed in neat cement slurry & pointed in coloured cement to match with the tiles, laid over and including screed bed 15 mm thick in CM(1:4) complete all as specified and directed.

Preparing New plastered or unplastered surfaces of walls and applying Two coat of cement base paint complete all as specified and directed.

Complete removal of existing treatment of old plastered or unplastered surfaces of walls and applying two coat of cement base paint complete all as specified and directed.

Complete removal of existing treatment of old plastered or unplastered surfaces of ceiling and applying two coat of oil bound distemper complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for roof trusses and purlins, complete all as specified and as directed

Two coat of synthetic enamel painting to steel Surfaces plain or moulded, n exc 10cm width or girth when unconnected with other painting or when painted in a different tint complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exe 15 cm bot not exe 22 cm long and dia 16 -20mm all complete as specified and as directed.

Solid PVC door frame of size 50 X 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplied and fixed in repair in opening as per specifications and drawing complete as directed.

Factory made solid panel PVC door shutters 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail, MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail; Panelling of plain colur PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement, Supplied and Fixed in the frame at site as per specification and drawings complete all as specified and directed.

Supply & fixed in repair, Pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanks and fly nuts screwed for 15 mm dia bore of pipe all complete as specified and as directed.

Bib tap 15 mm bore, Brass CP, fancy type (long shank). With capston head screwed down screwed for iron pipe or for brass ferrule and fixed in repair complete all as specified.

Angle cock (ISI Marked), cast copper alloy, fancy type chromium plated screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore and fixed in repair complete all as specified.

Supply & fixed in repair, Vitreous china wash basin, counter type oval shape of size 550 x 400 mm excluding taps, waste chain and plug and porcelain stopper but including brackets, waste pipe & CP waste coupling 32mm complete all as specified and directed.

PVC connection 15 mm bore with CP nuts of length 600 mm long complete all as specified and directed.

Grating doom 100 mm dia with waste hole of PTMT (minimum weight - 40 gms) complete all as specified and directed.

S & F in repair squatting pan of size 580 x 440 mm white, with integral foot rests including connection to trap, flushing cistern and flushing pipe, anti-syphonage pipe, etc. complete including 100 mm dia ‘S’ trap set in and including concrete making good to including jointing to existing pipe of floor of size 100mm complete all as specified and as directed.

Supply & fixed in repair, Vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe (excl flushing cistern, flush pipe and waste pipe).

Taking up or down steel tubing 15mm and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing 20 mm and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F GI tubing medium grade 15mm bore with all fittings, cutting, threading and fixing to walls,ceiling or in floors, complete all as specified and directed.

S&F GI tubing medium grade 20mm bore with all fittings, cutting, threading and fixing to walls,ceiling or in floors, complete all as specified and directed.

Excavation in trenches n. exc. 1.5m wide and n. exc. 1.5 m deep; in hard/dense ; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 sq.m on plan and n. exceeding 1.5m in depth and getting out complete all as specified and directed.

PCC (1:4:8) type D-2(Using 40 mm graded coarse aggregate) as in bed to 150mm dia drain pipe including packing under, and haunching aginst the size of pipe after they are laid and tested complete all as specified and directed.as specified .

150 mm bore reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed .

Brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:4 complete all as specified and directed.

PCC (1:4:8 type C-2 (Using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete, complete all as specified and directed.

PCC type B-1 1:2:4 (20 mm graded crushed stone aggregate) as in coping, bed plates etc slightly rounded or chamfered angles and throating, complete all as specified and directed.

15 mm thick rendering on fair faces of brick work in in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

Mild steel TMT bar 6mm to 8mm dia cut to length bend to shape required including crabking behind spirally for hooping for columns hooking ends and binding with and including mild steel wire (unnealed) not less than 0.9mm dia or securig with clips, compl.

Providing precast reinforced cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mirtar 1:4 complete all as specified and directed.

Removal of excavated material (soil)to a distance n. exc 50 m depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

PVC (SWR) floor trap of 75mm dia of outlet, plain with grating including jointing to waste pipe with solvent cement fixed, complete all as specified and directed.

PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe including clamps, complete all as specified and directed.

PVC (SWR) bends of any radius 110mm dia provided with access door, complete all as specified and directed.

PVC (SWR) branch piece of any radius 110mm dia double (double 'Y') equal or unequal, complete all as specified and directed.

PVC (SWR) 110 mm bore junction single, (Single T) equal or unequal complete all as specified and directed.

E/M Portion:-Taking down carefully unserviceable copper/aluminium point wiring including all fittings and making good to disturbed surfaces of wall, floor etc. to match with existing finishes complete all as specified and as directed.

M&L for point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light / fan point controlled by one switch complete all as specified and as directed.

One 5 pin, 6 A socket outlet on the same board complete all as specified and as directed.

One 5 pin, 6 A socket outlet on the independent board complete all as specified and as directed.

All as per item No. 119 above but for 2 x 2.5 sqmm (as phase and neutral) and 1 x 1.5 sqmm (as earth continuity conductor) for one 15 Amps socket outlet on independent board complete all as specified and as directed.

Ceiling rose, 3 terminal, surface bakelite 65 x 50mm complete all as specified and as directed.

Piano type switch, 1 way,6 Amps, flush type, complete all as specified and as directed.

Socket outlet 2 in 1,5 pin ,6 Amps, flush type complete all as specified and as directed.

Switch socket combination 5 pin, 6 Amps, flush type complete all as specified and as directed.

Switch socket combination 2 in 1, 5 pin and 15 Amps, flush typecomplete all as specified and as directed.

Lamp holder insulated body all as specified and as directed complete all as specified and as directed.

Inverter type LED Lamp, 12 watt, complete all as specified and as directed.

Electronic step regulator (speed regulation in 5 steps) suitable for ceiling fan 1200 / 1400 mm sweep complete all as specified and as directed.

LED light fittings, 1x20 w LED, 230 V complete with all accessories internally per wired including and connecting up with PVC insulated and sheathed, 1100 v grade, flexible, multistranded copper conductor three core cable complete all as specified and as directed.

Building security light fittings, 35 watt LED,230v, AC out door type pre-wired, IP-65/66 protection, with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket complete all as specified and as directed.

Sheet Metal enclosure for SPN DBs, 8 Ways, Double Door (IP-43), with netral link complete suitable for 240 Volts, AC, 50 Hz complete all as specified and directed.

Sheet Metal enclosure for SPN DBs, 12 Ways, Double Door (IP-43), with netral link complete suitable for 240 Volts, AC, 50 Hz complete all as specified and directed.

MCBs, SPN, 240 volts, breaking capacity 10 KA, rating 40-63 amps, complete all as specified and as directed.

MCB, SP,240 volts, breaking capacity 10 KA, rating 6 to 32 amps, complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of the earth plate not less than 1.5 m below ground level, connected to GI earth wire 4mm dia by means of bolts, nuts,check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of SSR Part-I, connected to earth test point all as specified or indicated including excavation and connected earth work in soft / loose soil, P.C.C 1:3:6 type C-1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 15mm bore GI medium grade earth lead protection pipe, 50mm thick R.C.C. 1:2:4 type B-1 cover slab of earth pit reinforced with 8mm dia TMT bars @ 10cm C/C both ways and with handle made out of 10mm dia bars, funnel, strainer,charcoal and testing on completion including dismantling unserviceable earthing complete all as specified and as directed.

Supply and laying in trenches/on floor/pole or under road/culvert 1100 volts grade armoured, heavy duty XLPE electric cable with aluminium conductor of size 16 Sqmm 2 core including taking down old/ unsv cable any type complete all as specified and directed.

S&F Sub main wiring with single core cable 2x 6 Sqmm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including suitable size PVC casing capping medium grade ISI marked alongwith 1x 4 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-Three wire of 2x 6 sqmm and 1x 4 sqmm and one run of PVC conduit/casing caping shall be measured as one unit.

Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply and fixing 1100 Volts grade heavy duty cable PVC insulated aluminum conductor, served with inner sheathing of PVC tape and overall PVC sheathed twin core cable flat or circular of size of aluminum conductor 10 sq mm stranded conductor including taking down old UNSV cable complete all as specified and directed.

S&F Sub main wiring with single core cable 2x2.5 Sqmm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including suitable size PVC casing capping medium grade ISI marked alongwith 1x 2.5 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-Three wire of 2.5 sqmm and one run of PVC conduit/casing caping shall be measured as one unit.

S&F in repair Sheet Metal enclosure for SPN DBs, 2 Ways, single door (IP-43), with netral link complete suitable for 240 Volts, AC, 50 Hz complete all as specified and directed.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as directed.

NATIONAL TRADING COMPANY (BID ID -3481673)

JAMWAL CONSTRUCTION CO (BID ID -3477636)

M/S FAIZ AHMED KHAN (BID ID -3476146)

M/S KEWAL KRISHAN SANJEEV KUMAR VAID (BID ID -3481540)

M/S IMRAN MAJID (BID ID -3476542)

M/S BHATT TRADERS (BID ID -3481526)