Renovation of DSW

Amount

Providing and fixing 3 seater chair stainless steel perforated seat back, Stianless steel pipe legs, frames having size 1390 (L) X 550 (D) X 890 (H) of approved make and as per the direction of Engneer-in-Charge.

WORKSTATIONS: Manufacturing, providing and placing in position machine madefactory assembled workstation of make Rockworth_ Rubix Series or equivalent of STEEL CASE / HAWORTH / GODREJ INTERIO make (as per finally approved sample by department) of following specifications: Frame Work, Partition and Cable management : Frame work shall consist of main spine and return spine of aluminium extruded section of minimum thickness of 1.2 mm. The overall thinkness of Panel base System should be 60-70 mm. The panel ill be hollow inside to accommodate wiring for electrical/data and outer frame of panel should be made of extruded aluminium. The panel shall be made up of 3 mm thick MDF both sides of the wooden frame to create the hollow for the wire management. Finishes of panel above the worktop: Above the top fabric pinup with raceway on main spine between workstation. The hollow panel made of MDF and 3mm thick foam which is upholstered with 0.5mm thick fabric with half fabric pinup + half glass marker board. The thickness of partition panel should be 60-70 mm for main & 25mm thick return spine. Finishes of panel below the worktop: Below the top the hollow panel should be made of MDF tile and 0.5mm thick steel sheet pasted on MDF which is powder coated with EPC finish 80-90 microns for durability on the inside as well on the outside. The thickness of partition panel should be 60-70 mm for main spine & 25mm thick return spine .The panel outer aluminium frame is designed such a way that it can be easily slide in to the columns/ Connectors by means of stacking one over the other.Horizontal race way should be 150-170 mm height aluminium profile. There shall be complete cable management arrangement with openable raceway below worktop with provision for fitting electrical/data switches and holes for passing cable. Connectors/ Post Description: End Post: Aluminium 60-70 mm width – 1200-1250 mm height. One way post: Aluminium 60-70 mm width – 1200-1250 mm height. Two way post: Aluminium 60-70 mm width – 1200-1250 mm height. Three way post: Aluminium 80-120 mm width – 1200-1250 mm height. Four way post: Aluminium 80-120 mm width – 1200-1250 mm height. Brackets: Table top support: 50-60mm width steel bracket.Table top to table top connector: 150-170 mm Width x 120-140 mm Depth width connector. WIRE MANAGEMENT trolley connected to Top of table should contain the horizontal cable channel that fitted with a modesty panel tidily and effectively. Raceway should be made out of CRCA steel of thickness 2mm duly powder coated.Powder coating should of 60-70 micron thickness to be provided fitted to the under structure legs of table. Powder coating should be scratch resistance (cross hatch test 6x6 grid method). Worktop: Worktop should be made of minimum 35mm thick MDF with PU polish or any approved shade/colour of natural veneer of thickness of 0.5-0.6 mm. MDF should be confirming to IS: 14587 grade II & Type II. The exposed edge of worktop shall be secured with 1.2mm-1.5mm thick PVC edge banding tape of approved colour. The height of Worktop shall be 740-760 mm from ground level. The MDF board should be E-1 Grade with pvc edge banding. WIRE Tray should contain the horizontal cable channel that fitted with top of workstations tidily and effectively provided with FLIP Top on the top of table with provision to be connected to wire management tray and provision of fixing electrical and data sockets. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310 mm (W). Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality. Worktop: Worktop should be made of minimum 35mm thick MDF with PU polish or any approved shade/colour of natural veneer of thickness of 0.5-0.6 mm. MDF should be confirming to IS: 14587 grade II & Type II. The exposed edge of worktop shall be secured with 1.2mm-1.5mm thick PVC edge banding tape of approved colour. The height of Worktop shall be 740-760 mm from ground level. The MDF board should be E-1 Grade with pvc edge banding. WIRE Tray should contain the horizontal cable channel that fitted with top of workstations tidily and effectively provided with FLIP Top on the top of table with provision to be connected to wire management tray and provision of fixing electrical and data sockets. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310 mm (W). Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality. Linear WORKSTATION – 1 group of two persons (Size : 1200mm x 600mm (Worktop Height) x 1200-1250 mm (Height of panel from Ground) for two person.

anufacturing, providing and placing in position machine made factory assembled Storage of make rockworth _ Zen Series_Cabinet or equivalent of STEEL CASE/HOWARTH/GODREJ INTERIOR make (as per finally approved sample by department) of following dimensions with the following specifications. Back Storage : The storages should be made of minimum Top 35mm thick MDF and 16-19 mm thick door, sides and shelves with approved shade of natural Veneer(minimum thickness of 0.5-0.6 mm) MDF should be confirming to IS: 14587 grade II & Type II. The exposed edge of worktop shall be secured with 1.5 mm-2 mm thick PVC edge banding tape of approved colour. The height of Worktop shall be 740-760 mm from ground level. The MDF board should be E-1 Grade with pvc edge banding. The exposed edge of panale secured with 1.2mm-1.5mm thick PVC edge banding tape of approved colour. The wiring tray is made of steel sheet thickness 1.2mm. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 5 years warranty. Back Storage 1650mmW x450mmD x740mmH

Providing & fixing steel almira with 2 doors, 4 adjustable shelf, thickness 0.8 mm, powder coated size : 750 x 485 x 1980.of approved make.and as per the direction of engineer in charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion . Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing in position 10mm thick of approved make polymultiwall polycarbonate clear structured sheets fixed to aluminium /MS frame with anodized aluminium profile(top and bottom) in approved colour with EPDM gaskets, stainless steel screws, silicon sealant etc complete to ensure a water tight structure as per directions of Engineer-in-Charge (Aluminium frame/MS Frame profile to be paid separately).

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : Decorative veneer facings of approved manufacture

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-incharge (Frame work shall be paid for separately). 12mm thick commercial ply conforming to IS : 1328 BWR type

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 800x800 mm

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing & fixing of Roller blinds at the existing doors and windows made of 1000% glass fiber fabric in with PVC foil coating in black out style with room darkening and blind with roll on the metal rod with the top of rollers fixed at the side metal bracket s duly powder coated including all other components as per approved colour & shade and all the blinds will be manually operated and to be made in different width & height as per requriement all complete with fixing charges inclduing material.as per direction of Engineer-in-Charge.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing.

Providing and fixing stainless steel letters "Directorate of students of welfare" with LED S. S. letters in height 16" height with 50 mm raising front with 0.75" laser cutting out line on 20 gauge SS 304 sheet raised letter 2" and Back cover sunboard sheet box in side 4 mm imported Acrylic sheet laser cutting letter for lighting complete with 1.2 W LED module powered by samsung with copper wiring & 3 nos. water proof power supply installation. Display on top of wall with logo of University with necessary fixing ararngemnts & as per the direction of Engineer-in-Charge

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. Size 40 mm

Providing and fixing stainless steel handles with necessary screws etc. complete: 75 mm

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. Triple strip vertical type

Providing and fixing shelves with commercial board marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). 18 mm thick

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.

Dismantling existing various type of light fittings/ ceiling fans/wall fans including disconnections etc complete as required

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. 'Group C

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required. Group C

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. '3 x 1.5 sq. mm

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. '3 x 4 sq. mm

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. '6 x 4 sq. mm

Supplying and drawing following pair 0.5 mm dia FR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 4 Pair

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. '20 mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. '25 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. '5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. '15/16 amp switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. '3 pin 5/6 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. '6 pin 15/16 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. '1 or 2 Module (75mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. '3 Module (100mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. '4 Module (125mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 6 Module (200mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 8 Module (125mmX125mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. '1 or 2 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 6 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 8 Module

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 2 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 3 run of cable

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying and fixing 400mm sweep 230 volt 50 HZ. Wall bracket fan with oscillating arrangement etc, as required.

Supply, installation, testing and commissioning of 34 W- 36 W recessed type cool day light 5700/6500 K, full glow LED panel of size 595 mm X 595mm, having minimum system lumen out put of 3600 lumens minimum system efficacy of 100 Lumen/Watt, power factor >0.90, CRI>80, THD<10 with APFC isolated driver with efficiency of >85% serge protection >2 KV operating voltage 150 to 270 volt, 50 Hz A.C. Supply. Complete with all accessories as per specifications to be fixed in existing Gypsum false ceiling, tightening with suitable M.S. Chain suspension arrangement. LED Chip make- Cree, Nichia, Philips, Lumiled, Osram, Edison, Seoul, Bridge lux, Luminare shall be complying to LM80 Report from LED manufacturer for 50,000 Burning Hrs and LM-79 Report from NABL accredited lab, connection with 3x1.5 sqmm FRLS PVC conductor wire etc, complete as required.

Supply, installation, testing and commissioning of 10 W- 12 W round recessed type LED Down Lighter having minimum system Lumen out put of 900 Lumen and minimum system efficacy of 100 lumen/Watt in die cast Aluminium heat sink/housing, Colour temperature (5700K to 6500K) power factor >90, CRI>80, THD<10 with APFC isolated driver with efficiency of >85% surge protection>2 KV, Suitable for operation on 150 to 270 volts, 50 Hz A.C. complete with all accessories as per the specifications in the existing cut out of size 165 mm dia in Gypsum false ceiling and repair of false ceiling/gypsum/calcium silicate etc if any for fixing. LED Chip make- Cree, Nichia, Philips, Lumiled, Osram, Edison, Seoul, Bridge lux, luminare shall be complying to LM80 Report from LED manufacturer for burning life of 50,000 Hrs and LM-79 Report from NABL accredited lab, connection with 3x1.5 sqmm FRLS PVC conductor wire etc, complete as required.

Supplying and fixing the following ms flexible pipe complete with all accessories i.e. Coupler, Saddle etc. as required. 25mm size

Credit Item on account of old material Fittings/Downlighters

Credit Item on account of old material Wire/Conduit etc

Credit Item on account of old material Switch & Socket with plate/Industrial Socket

Credit Item on account of old material Ceiling Fan/Wall fan/Exhaust Fan

NARESH KUMAR

Saranam Associates