Widening and Strenthening of Bahraich Huzoorpur Colonelganj Nawabganj Road (SH 155) Ch. 24.000 to 62.320

Amount

Excavation for trench of roadway in soil using manual means including loading in truck for carrying of cut earth to embankment site with all lifts and lead upto1000 metres.as per clause 301(3.1)

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5m , to site, spreading, grading to required slope and compacting to meet requirement of table 300.2 (without cartage)

Construction of subgrade with earthen soulders with approved material obtained from borrow pits with a lift upto 1.5m , transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300.2 (with Cartage)

Construction of Subgrade and earthen soulder,s deposited from roadway (Compaction only)

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with grader in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

Providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means.

Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects. (For V.G-40 Bitumen DBM Grade-2).

Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects. (For V.G-30 Bitumen DBM Grade-2).

Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects. (For V.G-30 Bitumen DBM Grade-1).

Providing and applying tack coat with bitumen using bitumen pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects (with VG-30 Bitumen).

Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects (with VG-40 Bitumen).

Construction of dry lean cement concrete Sub- base over a prepared surface with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a mechanical paver , compacting with 8-10 tonnes vibratory roller, finishing and curing.

Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing

Reinforced Cement Concrete M15 Grade Kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc (for Fifth KM stone).

Reinforced Cement Concrete M15 Grade Kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc (for KM stone).

Reinforced Cement Concrete M15 Grade Kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc (for HM stone).

ROAD SEFTY WORK- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including retroreflactive glass beads@ 250 gms per sqm area thickness of 2.5 mm is exlusive of suface applied glass beads as per IRC:35 the finished surface to be level uniform and free form streak and holes MORTH 803 (8.13).

Direction of place indentification sign with size more than 0.90 sqm size board providing and erecting direction place identification reflactoirised sign as per IRC 67 made high intensity grade shieeting wide clause 801.3 fixing over aluminium sheeting 2mm thick area exceeding 0.9 sqm supported on a mild steel angle iron post 75mm MORTH 801(8.6).

Providing and fixing of retero reflacting delinator post IZ-ASTMAD-456-4 Made of 75 mm dia round of 1.2 m high with fixing support

Supply and errective of build up Overhead structure 12m to 15m span comprising two vertical post of 6m high made up 300mm NB heavy class ms pipe as vertical member welded with 100 mm ms plate at top and bottom for bearing of horizontal MORTH 802.

Supply and errective of Cantilever structure 6 m span comprising o three vertical post of 6m high made up 300mm NB heavy class ms pipe as vertical member welded with 100 mm ms plate at top and bottom for bearing of horizontal MORTH 802.

Providing and Fixing of reflective signs with corrosion resistent 4 mm thick aluminium composit pannal as per IRC 67-2010 rectro reflective sheeting with M.S. angle frame 35 X 3 board etc.MORTH 801.

Thermoplastic Repeted Bar marking is a softer treatment to reduce the speed. One set of bar marking (refer TM 08) comprises of 6 bars of 300 mm wide. Each strip of thermoplastic strip shall be of 5 mm high and shall be set applied across the full width of the carriageway. MORT&H 803

Providing and fixing of retro relectorised cautionary, mandatory and infrormatory sign as per IRC :67-212 made of high intersity grade sheeting vide cluse 801.3 friced over aluminium sheeting type-IV 1.5 mm thick supproted on a mild steel angle iron post 75mmx75mmx6 mm firmly fixed to the gournd by means of propertly designed foundation with M 15 grade cement concrete 45 cm x 45 cm x60 cm, 60 cm below ground level as per approved drawing. The retro reflective sheeting shall be tested for 3 year outdoor weathering test in indian conditions as per IRC 37:2012 as per MORTH 801(8.4) (VIII). (i) 90 Cm equilateral tringle with diffinitation plate size (20cmX60cm).

Supply and fixing of Pavement Maker (Cat Eye) type X - ASTMD-4956-04 Avery denision/3-M (USA make) consisting of ASA Plastic housing fitted with tightyly adherent ploting compound. The housing shall contain prismatic to Glass covered prismatic reflecting face to reflect incident light /C al taxes.

(ii) 60 cm equilateral tringle with diffinitation plate size (20cmX60cm).

(iii)60 cm Circular with diffinitation plate size (20cmX60cm).

(iv) 80mm x 60mm rectangular with diffinitation plate size (20cmX60cm).

(v) 60mm x 45mm rectangular with diffinitation plate size (20cmX60cm).

(vi) 60mm x60mm square with diffinitation plate size (20cmX60cm).

(vii) 90cm high octagon.

(viii) 50x60 cm single chevron.

(ix)155x60 cm double chevron.

(x) 30x90 cm (Left/ Right) Object Hazard.

(xi) 45x90 cm two way object Hazard.

(xii) 30x90 cm + 45x78 cm Guarded/unguarded Railway Crossing.

H.P Culvert/ RCC Culvert/ Box Culvert/ Drain Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work.

Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.

Brick Masonry Work in Cement Mortar in Foundation complete excluding Pointing and Plastering, as per Drawing and Technical Specifications.(With Cement: Sand) - 1:3

R.C.C. Work with cement approved coarse sand and 20 mm gauge stone grit in proportion of 1:1.5:3 for slabs excluding supply of reinforcement and its binding but including its fixing and binding the same with 24 B.W.G.G.I. binding wire and including necessary centering and shutterring etc. and also including supply of all materials labour and T&P etc. required for proper completion of work. Binding wire cost being included in the item

Supplying, fitting and placing HYSD bar reinforcement in super-structure complete as per drawing and technical specifications

Stuck pointing with cement and fine sand of 1.25 fineness modulus morter on stone work in proportion of 1:2 including supply of all materials, labour and tools and plants etc. required for proper completion of the work

Providing and laying of weephole in brick massonary in abutment and wing wall with 100mm dia PVC pipe extending through the full width of the structuer with slope of 1v:20 H toward drawing force complete as per drawing and technical specification (MORTH &H-13.8/2706&2200)

M-10 in Foundation M-10 nominal mix in Foundation with crusd stone Aggrigate 40 mm Nominal size Mechenicaly mix ,Placed in foundation and Compactiing by Vibration including Curing for 14 days. MORTH 2100 Sr No. 12.04

Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical SpecificationsRCC Grade M25 using batching plant & manual placing( MORTH 1500,1700 &2200 Sr No. 15.11 E Case II)

PCC Grade M20 Using Batching Plant ,Transit Mixher and Manual PlacingRCC Grade M20 using batching plant & manual placing (MORTH 1500,1700 & 2100 Case II Sr No. 15.11 BII)

Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications MORTH 2702 Sr No. 15.2

Supplying, fitting and placing HYSD bar reinforcement in sub-structure complete as per drawing and Technical Specifications MORTH 1600 &2200 Sr No. 13.06

Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications MORTH 2503 Sr No. 16.01

Sand Filling in FDN complete as per Drawing and Technical Specifications. MORTH 304 SR No. 12.03

Laying Reinforced cement concrete pipe NP3/prestressed concrete pipe for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 and excavation, protection works, backfilling, concrete and masonry works in head walls and parapets . - For 600 mm dia

Laying Reinforced cement concrete pipe NP3/prestressed concrete pipe for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 and excavation, protection works, backfilling, concrete and masonry works in head walls and parapets . - For 900 mm dia

Routine Maintenance of road after completion of work :- (A) Carriageway/ Pavement: (a) Potholes, cracks, other surface defects (SWMM & BC), (b) Repair of Edges, Rutting (BC) (B) Road, Embankment, Cutings, Shoulders, Trees & Plantation : (a) Road Maintained free of edge drop, inadequate cross fall, undulations, settlement, Ponding (E/W), (b) Deficent slopes, rain cuts in embankments (E/W), Vegetation growth, Loping of tree branches. (C) Bridges and Culverts: (a) De-Silting, (b) Clearing vegetation growth (Jungle Clearance), (c) Damaged/distrubed boulder pitching, breast/toe wall retaining wall, apron flooring, guide bunds (Boulder Apron), (d) Parapet, any damage to foundations, (e) Any defects in sub-strucures, (f) Any defects in superstructures, raillings, parapets. (g) Wearing coat, (h) Approach slab, (i) Painting & Lettering of No. plates, repair. (D) Repair of Roadside Drains: (a) Brick Work in 1:4, (b) Plaster, (c) CC- 1:2:4. (E) Road Furniture: (a) Cleaning, Painting & lettering of stones & sign boards, Replacement of damaged/ missing stone & sign boards. (b) 200 m Stones, (c) Km stones, (d) 5th km stones. Maintenance requriment as per above and Mentioned in Special Condition of Contract for Maintenance. Payment of Maintenance work as Percentage of final Civil Construction Cost :

a) For Ist Year @ 0.00%

b) For IInd Year @ 0.25%

c) For IIIrd Year @ 0.50%

d) For IVth Year @ 0.75%

e) For Vth Year @ 1.00%

M/s Raj Laxmi Enterprises (BID ID -5800393)

C S Infraconstruction Limited (BID ID -5799638)