Construction of Laboratory Counters and allied works in 04 No. Pre-fabricated Laboratories in Govt. Degree College at Bishnah (LUP 1682, Under Languishing Programme)

Amount

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate) 40mm nominal size crushed.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level. 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) Crushed.

Half brick masonry with bricks of class designation 75 in foundation and plinth in cement mortar 1:4 (1 cement : 4 coarse sand).

Extra for half brick masonry in super structure above plinth level upto floor V-level

Providing and laying in position 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement. All work up to plinth level using crushed aggregate.

Providing and laying in position cement concrete of 1:3:6 grade (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20mm nominal size) excluding the cost of centering and shuttering. All work upto plinth level.

15mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement : 4 fine sand).

Centering and shuttering including strutting, propping etc. and removal of form work for :-

Foundations, footings, bases of columns.

Suspended floors, roofs, landings, balconies and access platforms.

Edges of slabs and breaks in floors and walls upto 20cm wide.

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars.

Providing and fixing 10mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding and joints filled with acid and/or alkali resisting cement as per IS:4457 complete as per direction of Engineer-in-charge in flooring on a bed of 10mm thick mortar 1:4 (1 acid proof cement: 4 coarse sand). Acid and alkali resistant tile.

Fabrication and installation of cabin and racks by way of Providing and fixing 19mm thick water proof particle board with both side lamination with 0.80mm thick laminated (Sunmica) sheet conforming to IS specifications (complete job).

Providing and fixing 6mm thick water proof ply including one side lamination with 0.80mm thick laminated sheet conforming to IS specifications on back side of cabin and racks (complete job).

Providing and fixing aluminium handles ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. 100mm.

Providing and fixing aluminium sliding door bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. 250x16mm.

Providing and fixing sliding glazed shutters with glass of 6mm thickness in cup board including channel, roller, handle and all assories (complete job).

Providing and fixing gas connection from gascylinder to working site including supply of burner with stand, composite pipe of Ki-tec, stopper regulator nozle, nozle connector alongwith regulator near cylinder as per IS specification. The work shall be done as per direction of Engineer-in-charge (complete job).

Steel work welded in built-up sections/framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar, ladders, railings, brackets, gates and similar work.

Providing and placing on terrace( at all floor level) Polythene water storage tank ISI 12701marked indicating the BIS licence no with cover and suitable locking arrangement and making necessary holes for inlet , outlet and overflow pipes but without fittings and the base support for tank ( SINTEX / STAR/Lotus) (02 Nos. 500 ltrs capacity each).

Providing and fixing G.I connection to PVC water tank with nipple 20mm, union, nipple, 100mm sockted brass ball valve including 20mm teak for air pipe making conforming to IS specifications (complete job).

Providing and fixing flame hood of 1 feet dia of stainless steel of 24 gauge .

Providing and fixing G.I pipes complete with G.I fittings and clamps, including cutting and making good the walls etc. 20mm dia nominal bore (Medium).

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug 40mm C.P. brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete including painting of fittings and brackets, cutting and making good the walls wherever required size 600x450x200 mm.

Providing and fixing uplasticised PVC connection pipe with brass unions. 15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved make conforming to IS : 8931. 15mm nominal bore.

Providing and fixing of sink cock tap of U-shaped of make Cera, Hindware, Parco conforming to IS marked (complete job).

Providing and fixing of 1 HP Motor Crompton/Keloskar conforming to IS marked (complete job).

Carriage of material by Mechanical Transport including loading / unloading and stacking at site complete.

Stone agg. below 40mm size for an avg. lead of 10 Kms.

Sand for an avg. lead of 10 Kms.

Bricks for an avg. lead of 15 Kms.

ranjeet kour

M/s Anil Gupta