SPECIAL REPAIR TO BLDG NO. T-03 (QM OFFICE) AND JCOS MD ACCN BLDG NO. P-169/1 TO P-169/6 (CONSISTING OF 06 QTRS) AT THE GRENADIERS RC JABALPUR (MP) UNDER GE(WEST) JABALPUR

Amount

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cms thickness (below or above ground level) including removal of debris to out side MD land complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removal of debris to out side MD land complete all as specified & directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified & directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil complete all as specified and directed.

Excavation over areas, n exc 1.5m deep & getting out in Soft/loose complete all as specified & directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L vitrified ceremic tiles 10 mm thick, in light shade, (Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specfied and directed.

All as per above item but in skirting with rendering 10mm thick CM 1:4 complete all as specified and as directed.

M & L Non Skid ceramic joint free tiles 7 to 8 mm thick ( square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of mortar with CM 1:4 complete all as specified and directed.

M&L for glazed ceramic tiles colour 350x250x7mm / 450x350x7mm thick in vertical surfaces such as skirting, dado and risers to steps set and jointed in neat cement slurry and pointed in coloured cement to match over 10mm thick cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing for tiles complete all as specified.

M & L providing, cement concrete type B1 1:2:4 (20 mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M & L 75mm thick PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in plinth protection, finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster etc on brick walls/ concrete (ceiling) surfaces of any descriptions including racking out joints, hacking for keys, scrubbing down with water and disposal of unserviceable materials to out side of MD land complete all as specified & directed.

M&L for rendering 15 mm thick in two layers(10mm thick in CM 1:6 & 5mm thick in CM 1:4) on external surfaces of wall, finished even and smooth without using extra cement complete all as specified & directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in CM in 1:6 finished even and fair without using extra cement complete all as specified & directed.

M&L for 02 coats of cement base paint on walls including preparation of surfaces on plastered new surfaces complete all as specified & directed.

M&L for applying 2mm thick wall care Putty in two layers and two coats of oil bound distemper including primer on old surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete all as specified & directed.

M & L preparation of walls old plastered surfaces & applying two coats of cement based paint complete all as specified & directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified & directed.

Ditto as per item above but except bricks. ( Note : Serviceable bricks retrieved gainst dismantling shall be re-used)

M & L preparation of new steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of primer complete all as specified & directed.

M & L preparation of old steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint complete all as specified & directed.

M & L preparation of old wooden surfacesof any description over 10 cm width or girth & applying two coat of synthetic enamel paint complete all as specified & directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.50 sqm each and removal complete all as specified & directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area exc 1.50 sqm but n.exc 4 sqm each and removal complete all as specified & directed.

S & F powder coated (min thickness of powder coating 50 micorn) Aluminium door, window,ventilator frame with one or more rebates and shutter incl jointing cleat for fixing etc. including making good to the disturbed surfaces and matching existing treatment (cement base paint/distemper/white wash/plastic paint) etc including taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area exc 1.50 sqm but n.exc 4 sqm each and removal complete all as specified & directed.

S&F powder coated of any colour aluminum door shutters, aluminium section weighing 0.55 Kg/ Rm including necessary jointing cleats, glazing clips, ruber neoprene packing, handles 02 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S&F powder coated aluminum window and ventilator shutters, fixed type without sash bars, aluminium section weighing 0.55 Kg/ Rm including necessary jointing cleats, glazing clips, ruber packing, anodised aluminium snap beading, screws etc. including making good to the disturbed surfaces complete all as specified and directed.

S&F galvanised MS wire cloth, 0.56mm nominal dia of wire average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed.

S&F 4 mm thick sheet glass, ordinary quality and glazing with rubber gasket in square exceeding 0.5 Sqm in each pane, complete all as specified and directed.

M & L Granite (Black/Ruby Red ) work (table rubbed and polished) 20 mm thick in cooking platforms bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including grinding and polishing complete over and including screed bed 15 mm thick in CM 1 : 4 complete all as specified and directed.

M&L Cudappah stone slab on cooking platform/shelf 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match with the shade of stone slab, over and including 20mm thick screed bed in CM 1:6, including rubbing and polishing and cutting of holes for gas pipe complete all as specified and directed.

M&L for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars and similar work conforming to Fe- 290 ( Gde-E-165) complete all as specified and as directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts). No claim whatso ever shall be entertained by Govt on this account.

Dismantling of walll and ceilling boards (fibre,pulp,insulation,etc) or insulation boards/slabs/bblankets, any thickness including cover fillets complete all as specified and as directed.

M&L for suspended false ceiling system using chicago metallic (E grid)exposed supended system, grid section size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions 39 mm X 24mm X 0.8mm thick (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600mm length) Cross Tee of dimensions 29mm X24mmX0.8mm thick and thick wall angle 22.2mmX22.2mmX 0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length)with and including 4mm thick HPSC(High pressure steam cured) pre-primed , self embossed . textured designer board, water resistant termite resistant , fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with butterfly clips(Wt-0.007 Kg/clip)hold down clips (Wt-0.0035 Kg/clip) with Provn of light fixture complete all as directed.

S & F for Wash basins, Table Top Basin ,fixed in repairs complete all as specified and as directed.

S & F in repair for Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, 15 mm, fancy type fixed complete all as specified and as directed.

S&F in repair for vitreous china full stall urinals,white, complete including providing and fixing plugs, securing urinals to plugs with and including 60mm long brass screws, fixing flush pipe, grating and union for discharge pipe.

S & F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60 gms) complete all as specified and as directed.

S & F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube manufactured as per SSR Part I specifications and drawing complete all as specified and as directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) manufactured as per SSR Part I specifications and drawing. consisting of frame made out of MS tubes for top & Bottom rails. MS frames shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement manufactured as per SSR Part I specifications and drawings complete all as specified and as directed.

S&F 100mm long aluminium butt hinges alloy with galvanised ms hinge pin, anofised and fixed type C-21 complete all as specified and as directed.

S&F 150mm long aluminium anodised barrel tower bolt and fixed complete all as specified and as directed.

S&F 125mm long aluminium anodised handle cast type and fixed complete all as specified and as directed.

S&F 300mm long Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed.

S&F, PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, laid in trenches or fixed on walls complete all as specified and as directed.

S&F, PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls

S&F PVC (SWR) bends ISI marked any radius of 110 mm bore with access door complete all as specified and directed.

S & F PVC (SWR) bends any radius, 75 mm bore complete all as specified and as directed.

PVC (SWR) 110mm bore 'T' equal or unequal complete all as specified and directed.

PVC (SWR) vent cowl for 110 mm bore pipe complete all as specified and as directed.

PVC (SWR) floor trap with grating 75 mm dia including jointing with solvent cement complete all as specified and as directed.

M & L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 100 mm bore, complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 15mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 20mm bore of pipe complete all as specified and as directed.

Supply and fix in repair 10 ltr capacity PVC valve less syphonic action type flushing cistern low level 'white' with inlet ball valve, float valve & handle Including 32mm bore PVC flush pipe & brackets and brackets fixed to wall complete all as specified & directed.

S&F in repairs white vitreous china wash down water closet pan pedestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe complete all as specified and as directed.

S&F, in repair, plastic water closet seat, white/ black closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device complete all as specified and directed .

S&F, in repair, Stainless steel conduit curtain rod with PVC coating fancy type curtain rod 20 mm dia of any colour including end globe as approved by GE, complete including side mounting complete all as specified and directed .

S&F Stainless steel Bracket with PVC coating fancy type for curten rod 20 mm dia of any colour as approved complete all as specified and directed .

Supply & laying of CPVC pipes 16 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete all as specified and directed .

S & F, in repair, Stop valves, cast copper alloy, chromium plated concealed type screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed , 20 mm fixed complete.

S & F, in repair, Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed complete.

S & F for PVC connections 15 mm size with PTMT nuts of length 6000mm fixed complete all as specified.

Towel Rail 600mm long of PTMT/SS fixed with and including Chromium plated brass screws and wooden/plastic cleats .(Minimum weight 190gms) fixed complete all as specified and directed .

Supply and fix 500 ltrs capacity rotational moulded polyethylene water storage tank double layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

S & F in repair for Grating doom 100 mm dia of chromium plated (Minimum weight 25gms) fixed complete all as specified & directed.

S & F in repair for Soap dish, any type, fixed to plugs with chromium plated brass screws fixed complete all as specified and directed.

PVC (SWR) floor trap with grating 75 mm dia incl jointing with solvent cement

S&F in repair Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for iron pipe complete.

M & L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified & directed.

M&L 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed

M&L for Machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment, conforming to IS 15658-2006of 60mm thickness, M 35 Grade of concrete, laid over and including 50mm thick sand cushion complete all as specified and as directed.

M&L PCC 1:2:4 type B-1 (using 20 mm graded stone agg) as in seismic and other similar bands, coping, bed block or similar work including necessary form work complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as required for 150 mm internal dia of pipe complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified & directed.

M & L solid wall DWCP socketed drain pipes class SN-8, conforming to IS 16098 (Part-2) with 150 mm bore dia in 6m length including laying and jointing complete all as specified and as directed

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 using 20 mm graded stone aggregate in foundation, including rafts, footings, beams, plinth beams; bases for columns; etc; basement slabs, under-remed piles and mass concrete complete all as specified & directed.

M&L for RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in cloumns, pillars, piers, posts and struts complete all as specified & directed.

M & L for RCC 1:2:4 Type B1 using 20mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified & directed.

M & L for RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed.

M&L for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams sides and soffits (if any) of foundation and plinth beams and similar works; vertical or to batter, complete all as specified & directed.

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified & directed.

M & L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelves including sup- ports, overhangs,etc. also splays between floors and beams, etc. complete all as specified & directed.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete for flat rough surface of finish, complete all as specified & directed.

M&L for mild steel TMT bars 10 mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 8 mm dia as in stirrups, spacers and binders for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Supply only Expanaded metal in required size , weight n. exc 4 Kg /Sqm complete all as specified and as directed .

Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided for, complete all as specified & directed.

M&L 25mm thick PCC 1:2:4 type B0 (12.50mm graded crushed stone aggregate) as in floors finished even & smooth using extra cement in patches complete all as specified and directed .

M&L 15 mm thick rendering in CM 1:4 on external surfaces of walls & top surfaces of chajja/roof, mixed with liquid water proofing compound as per Manufacturer's' instructions, surface finished even and smooth without using extra cement complete all as specified & directed. ( Note : Liquid water proofing compound will be measured and paid for separately against relevant item of BoQ)

Supply only liquid water proofing compound ISI Marked, of make as approved by GE complete all as specified & directed.

M&L for preparing new plastered surfaces of wall and applying three coats of white wash on walls complete all as specified & directed.

M & L for rendering 5 mm thick in CM (1:3) on Ceiling in patches, finished smooth without using extra cement complete all as specified and directed

M & L applying two coat of white wash on newly plastered or unplastered ceiling surfaces including preperation of surfaces, complete all as specified & directed.

Supply & laying of CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete all as specified & directed.

S&F, in repair, chromium plated mixer for wash hand basin for mixing hot and cold water, screwed down for iron pipes suitable for 15mm bore pipe complete all as specified and directed .

S & F, in repair, Brass chromium plated bath Mixer (2/3 hole) for mixing hot & Cold water arrangement, long shank suitable for 15mm bore of pipe of approved quality screwed down for iron pipe and fixed complete all as specified & directed.

M & L for cutting chases, pinning in brick walls/ stone concrete block or slab walls , making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings , steps, cills, sunshades, shelves, lintels etc; and cutting chases for concealed water tubing or cocealed conduit wiring, etc and making good , cutting not exceed 10 cm girth complete all as specified and as directed.

Taking down eaves gutter,rain water pipes of any size or pattern including all fittings etc complete all as specified and directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified & directed.

S&F PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe with access door complete all as specified and directed.

S&F PVC (SWR) junction single, (single T) equal or unequal of 75 mm bore of pipe complete all as specified and directed.

S&F PVC (SWR) junction single, (single T) equal or unequal of 75 mm bore of pipe with access door complete all as specified and directed.

S & F PVC (SWR) branch piece 110mm bore, single (single Y) equal or unequal complete all as specified and directed.

Supply & fix, in repair, kitchen sink with drainage board made of stainless steel 1.0mm thick with plug, washers with and including 32 mm dia PVC rigid waste pipes and C.P coupling including fixing cantilever brackets of suitable shape & size as required at site and connecting unions to pipe, overall size 915 mm x 460mm, bowl size 410 mm x 330 mm x 160mm and necessary cutting to slab complete all as specified & directed.

S&F in 0.63 mm thick kitchen plate rack made of stainless steel 900 x 750 x 220 mm size fixing with wooden plug with suitable size of screws complete all as specified and directed.

Taking down Shutter exc. 1 sqm and not exc. 2 sqm each complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staples beads or in steel window complete all as specified and directed.

Supply only floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm complete all as specified and directed.

M&L for pressed steel door frame size 125 mm x 60 mm and 1.25 mm thick including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and directed.

M&L for providing PCC 1:2:4, type B-0 (using 12.50 mm graded stone aggregate) as in filling of pressed steel door frame and holdfasts including necessary farmwork etc. complete all as specified and directed.

M&L for factory made second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats complete all as specified & directed. Notes:- (i) glazing will be measured and paid for separately. (ii) Butt hinge will be measured and paid for separately .

M&L for factory made 35mm thick second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, framed, panelled shutter (two or three panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stiles as per IS: 1003 (Part-I), kiln seasoned complete all as specified & directed.

S&F in 18mm rigid prelaminated coloured solid PVC sheet suitably fixed in MS angle frame work as in cup board , Cabinate ,Drawer etc as per manufacturer specification and drawings complete all as specified and directed. (Note :- Mild steel frame work shall be measured and paid for separatly.)

M & L for 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished

S & F factory made single piece extruded solid PVC door prelam frame (single rebate ) made out of single piece extruded (SPE) solid PVC foam profile with smooth outer integral skin having of size 90mmX 47mm PVC profile throughout reinforcement with MS tube with PVC Sheet As per manufacturer specification and direction of Engineer-in-charge.

S&F 100 mm long aluminium alloy type C-22 butt hinges with galvanised ms hinge pin etc. complete all as specified & directed.

S&F 200mm long aluminium anodised barrel tower bolt and 12 mm dia fixed, complete all as specified & directed.

S&F 150mm long aluminium anodised handle cast type and fixed, complete all as specified & directed.

S&F 100mm long aluminium anodised handle cast type and fixed, complete all as specified & directed.

S&F alluminum alloy, anodised, sliding door bolt with hasp & staple (bolt type) and length of 250 mm long etc., complete all as specified & directed.

S&F 100mm long butt hinges medium weight, cold rolled mild steel and fixed, complete all as specified & directed.

S & F Door spring ordinary rat tail rod pattern springs including roller and roller plate complete of mild steel 150mm long complete all as specified & directed.

Hacking out old broken glass(any thickness, size, quality or description) from wooden/steel frames, glazed with putty or fixed with beads complete all as specified and as directed.

S&F 3mm thick figured glass pin head type and glazing with oil putty or wooden beads in squares n exc 0.50 Sqmtr each pane complete all as specified and directed .

S&F continuous (Piano) hinges,mild steel, bright finish or electro galvanised width of flaps (when open) 30 mm complete all as specified and directed.

M&L two coat of synthetic enamel paint over new wooden surfaces of any description not otherwise described over 10cm in width or girth, over one coat of pink primer including preparation of surfaces compelte.

M&L two coat of synthetic enamel paint over new steel surface of any description over 10cm in width or girth, not otherwise described over one coat red oxzide primer incl preparation of surfaces complete.

M&L for 40 mm bore low density polyethylene pipes (LDPE) with fittings of pressure rating 6 Kgf / Sqcm fixed to walls or in floors etc complete all as specified and directed.

S&F in repair chromium plated shower rose fancy type fixed to 15mm bore pipe complete all as specified & directed.

S & Fin repair for Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed, 15 mm, fancy type, chromium plated fixed complete all as specified & directed.

S & Fin repair for Stop valves, cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed , 15 mm fixed complete all as specified & directed.

S & F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats(Minimum weight 300gms) fixed complete.

S & F Sheet corner glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified & directed.

S & F, in repair, Brass Chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges including taking down the existing towel rail.

Supply & fix vitreous china squatting pan, Orissa pattern of size 580x440 mm white, with integral foot rest and PVC 'P' or 'S' trap including connection to trap, and to flush pipe, etc (excluding flushing pipe) and making good to floor complete all as specified & directed.

S & F Vitreous china WHB 550x400mm on exsting brackets , fixing flat back or angle back type with PVC (HDPE) 32 mm dia waste pipe, brass coupling 32 mm CP etc fixed in repair complete all as specified and directed.

S & F Door Seal rubber etc,complete all as specified & directed.

S & F PVC cabinate with mirror etc, complete all as specified. Make : Prayag : (Size : 400 x 500 ) complete all as specified & directed.

Complete removal of existing treatment on walls including steel wire brushing and scraping etc and applying 3mm thick( Avg) Birla wall care putty in two layers on wall surfaces including rubbing, levelling and preparing the surfaces for receiving further finishes as directed.

M&L for preparation of old decorated surfaces of ceiling including brooming down or steel wire brushes, scraping down smoke soot moulds, moss and effeorescent salts and trading oil and greasy spot and applying one coat of white wash complete all as specified & directed.

M&L for applying two coat of distemper Oil emulsion white or tinted on new putty surfaces of wall complete all as specified and directed.

M&L for preparation of old surfaces of wall and applying two coat of distemper Oil emulsion white or tinted complete all as specified & directed.

Material & Labour for complete removal of existing treatment on walls by scrapping with steel wire brushes or sand paper & washing & rubbing down with water and after cleaning the wall surface, facia of roof projections or chajjas surface and applying two coats of weather proof Exterior emulsion first quality paint of approved colour and shade on external wall surfaces etc as per manufacturer instruction complete all as specified & directed.

M & L for preparing surfaces of sunken floor by brooming down or steel wire brushing and cleaning the surface with water and applying a coat of Rendercok HBF water proofing coating as per manufacturer's instructions over slab and sides of sunken complete all as required and as directed .

M&L for complete removal of existing water proofing treatment from top of roof and canopies / chajjas of building including removal of debris out side MD land all as directed.

M&L Water proofing treatment on roof surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete

M&L for 10mm thick rendering over roof surfaces in CM 1:3 , finished even and smooth without using extra cement complete all as specified & directed.

Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster complete all as specified & directed.

Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm including cleaning surfaces complete all as specified & directed.

M&L for unrolled over the bitumen coated surface, 3mm thick spun bonded non-woven polyester reinforced APP modified water proofing membrane weighing not less than 3.0 Kg/Sqm with minimum side over lap of 100mm and end over lap of 150 mm shall be sealed by flame as per manufacturer's instructions complete all as specified & directed. Note:- Suitable embedment of APP modified water proofing membrane shall be ensured into walls/parapet walls, special care shall be taken in laying APP modified water proofing membrane in situations such as drain/ expansion joints etc.

M&L for applying a coat of bituminous aluminium paint @ 100gm/ sqm over non-accessible roof and blinding material such as dry sand @ 0.75Kg/ Sqm over & including a coat of hot air blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm over polymeric membrane complete all as specified & directed. Note- Bituminous aluminium paint shall be of same manufacturer as specified for polymeric water proofing membrane.

Cement concrete tiles size 25cmx25cmx22mm thick machine cut pressed set jointed and pointed in neat cement slurry with grey cement and pigments fixied in floors over & including 15 mm thick scred bed in cm 1:6 and cut and polished complete all as specified and directed

M & L for formwork to chullah hoods,chajjas, troughs and similar items including edges etc., work in rough finished flat surfaces of concrete complete all as specified.

M & L for RCC (Nominal mix)1:2:4 Type B1 using 20mm graded aggregate as in Chajjas etc complete all as specified and directed.

M & L for second class hard wood plain fillets, square, rectangular or triangular in section, bull nosed, splayed, chamfered or rounded on one edge or face, sectional area exceeding 13 and not exceeding 25 Sq. cm., clean sawn, secured with nails or brads, complete all as specified and directed

S & F Hasp and Staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws 75 mm size, complete all as specified and directed

S & F Ball catches with 8 mm dia., steel ball, and brass body and striking plate including letting in and fixed, complete all as specified and directed

M & L for First class hard wood beads, straight (any Size) for glazed or gauzed joinery, renewed, including mitres etc., and removing old beads to store, complete all as specified and directed

M & L Machine cut Kota stone slab flooring 20-25 mm thick over and including cement screed base 20mm thick in CM( 1:4), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed

M & L Kota stone slab 18 to 20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 10mm thick rendering in cement mortar 1:4 , on fair faces of brick work or concrete surfaces as backing complete all as specified and directed

M & L for providing and injecting chemical emulsion for Post Constructional Anti Termite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per q. M of the vertical surface of the sub-structure to a depth of 300 mm including excavating channel along the wall and rodding etc., complete all as specified and directed

M & L Hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/ rammed to a true surface, complete all as specified and directed

Dismantling water tanks capacity exc 250 Ltr but n exc 500 Ltr and removing from site complete all as specified and directed.

Providing precast cement concrete 1:2:4 type B-1 (using 20mm graded stone agg)as in manhole covers set in cement motar 1:6 all as specified and directed including necessary formwork and moulds all as specified.

M & L for Cutting into existing manholes for connecting new drains, making good to pipe and ren-dering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 100 mm bore of pipe complete all as specified and directed.

M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc complete all as specified and directed.

Taking down carefully any type point wiring (light, fan, socket bell or power) , complete with fitting such as switches ceiling roses,lamp holders sockets,regulators,call bell light fitting with PVC conduit surface /concealed or wooden pattens including sunken cast iron /pressed steel terminal boxes etc complete all as specified and directed .

Taking down carefully ceiling fan/Exhaust Fan of any sweep and size and depositing to MES store and Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed .

Taking down carefully Main switch and Distribution boards any make and size complete all as specified and directed .

Taking down carefully Old unserviceable any type sub main wiring with wooden batten/PVC surface conduit of any size complete all as specified and directed .

Material & Labour Sub main wiring with four single core PVC Insulated cable two run of size 4.0 Sqmm multi-strand copper conductor FRLS cable 1100 volts grade drawing into PVC conduit, medium grade not less than 25 mm dia with all conduit accessories and one run of 4.0 Sqmm multi-strand copper conductor FRLS cable as continuous earth wire including making good disturbed surface to match existing complete all as specified & directed. Note : - two run of 4.0 Sqmm & one run of 4.0 Sqmm cable shall be measured as one unit run.

M/L for Sub Main Wiring two single core PVC insulated cable of size 6.0 Sqmm multistranded copper conductor two run drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting,fixing accessories and one run of 6.0 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :-Two Nos of 6.0 Sqmm Wire and one No of 6.0 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor cable 1100 volts grade drawn into and including concealed PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of antirorrrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed by Engineer in charge.

One light point controlled by one switch.

One fan point/exhaust fan controlled by one switch.

One socket point controlled by one switch on same board.

One socket point controlled by one switch on Independent board.

Description all as per item No 185 here in before but with 1100 volts grade copper standard conductor cable of size 2.5 Sqmm with 1.5Sqmm solid copper conductor PVC for 3 pin switch socket outlet 15Amp independent board complete all as specified and directed .

M/L for fan regulator socket type AC 230 volts complete all as specified and directed .

M/L for Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed .

M/L for Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed.

M/L for Switch socket combination 3 pin 5 and 15 Amps AC 230 volts flush type complete all as specified and directed .

M/L for ceiling rose surface bakelite 65 mm x50 mm three terminal AC 230 volts flush type complete all as specified and directed .

Supply & Fixing Smart bright Batten Series, LED luminaire using LEDs 22 watt 110 LM/watt with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets (supplied along with The Luminaire has been tested as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), report has established conformity of the product(s) to the requirements of the Standard/Specification complete all as specified and directed

S & F LED light fitting 1x9W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed .

S & F Sheet metal enclosure DBs Single Pole and Neutral 8 way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and directed .

S & F MCB single pole and neutral 240 volts 40 Amps, 'B' Series complete all as specified and directed.

S & F MCB single pole 240 volts 6 to 40 Amps, 'B' Series complete all as specified and directed .

Supply & fix, in replacement, LED Security Light Luminaire 35 watt 6000K with .high power LED cool white,CRI 75,+ 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens. complete all as specified and as directed.

S&F Sheet metal enclosure MCB distribution board including 200 Amps bus-bar triple pole and neutral vertical 415 V, 4 Ways, double door type,complete all as specified and directed. With Incoming MCCB of 100 Amps Capacity complete all as specified and as directed.

S & F MCB TP 25 to 63 Amps, 240 Volts, minimum 10 KA, "C" series rupturing capacity and to be housed in DBs catered here in before complete all as specified and directed. (Note :- Proper and suitable size cable copper lugs to be fixed with MCBs are included in unit rate of each MCB of any rating)

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Supply & Fixing in repair single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with 01 number single pole MCB 20 Amps complete all as specified & directed.

S&F LED light fitting square 59.5x59.5 CM Not less than 36 watt along with fixture Surface / Recessed /Pendent mounting LED luminaries with diffuser channel Luminaires ers, connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed .

Supply , laying and testsilng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cab les ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 3.5 core 50 Sqmm complete all as specified and directed.

Supply,laying & fixing double wall corrugated (DWC) pipes, 50 mm outer dia and 38 mm inner dia, made of high density polythethyline (HDPE) with all accessories i.e. all type of joints,Sockets,Elbows,bends and End caps etc with all as required complete all as specified and directed.

S & F in repair for bell ding dong AC 230 volts single pole one way complete all as specified and directed .

S & F in repair fan regulator Step type of polycarbonate complete all as specified and directed .

Supply and fixing in repair of LED lamp rotary type/holder type of 12 watt all as specified and directed .

Supply and fixing in replacement of decorative wall light fitting WITH LAMPS 9 WATT made up of Polycarbonate , City-1 , Cylindrical shape , with LED lamp 9 Watt complete with fixing arrangements on wall all as specified and directed.

S & F in repair of LED Decorative /mirror light fitting 9 watt along with fixture Surface mounted suitable for indoor aplication , connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed .

S & F in repair Bulk head endura LED light fitting complete with10 watt LED and making necessary electric connection to ceiling rose with copper conductor of suitable size & length complete all as specified & directed.

S & F in repair Sheet metal enclosure DBs Tripple Pole and Neutral 4- way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and directed .

S & F, in repair, MCB TPN 415 volts 63 Amps, C Series complete all as specified and directed .

Supply and fixing Single phase ceiling fan 1200 mm permanent magnet brushless DC Motor 230 v 50 Hz single phase 26-30watt rated current 0.16 amp,pf 0.98 370/360 rpm air delivery 220m3 rated service value 629m3/min/watt no of blades three type of blade leaf 1.05 mm thick aluminium sheet remote control radio frequency 5 speed +off timer option speed regulation class of insulation two nos bearings including connecting wire complete with all as required and directed .

S & F in repair Sheet metal enclosure DBs Single Pole and Neutral 8 way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and directed.

Supply and fixing in replacement MCB/Isolators single pole 240 volts upto 40 Amps, B Series complete all as specified and directed.

Supply & Fixing in repair single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with 01 number single pole MCB 20 Amps complete all as specified & directed.

S & F in repair for bell push piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed .

S&F Sheet metal enclosure MCB distribution board including 200 Amps bus-bar triple pole and neutral vertical 415 V, 12 Ways, double door type,complete all as specified and directed.

S & F MCCB TP 63 Amps, 240 Volts, minimum 16 KA, "C" series rupturing capacity and to be housed in DBs catered here in before complete all as specified and directed . (Note :- Proper and suitable size cable copper lugs to be fixed with MCBs are included in unit rate of each MCB of any rating)

S & F Exhaust fan heavy duty metallic body size sweep 300 mm sweep, 230 v, 50 Hz , complete with louvers including making holes and making good the disturbed surface complete all as specified and directed .

S & F Exhaust fan plastic body size sweep 300 mm sweep, 230 v, 50 Hz , complete with louvers including making holes and making good the disturbed surface complete all as specified and directed.

Supply , laying and testing cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 4 core 25 Sqmm complete all as specified and directed.

Schedule of credit amount of Rs 68,465.00 to be deducted during AOC

Kirti Chandeliya and Assosicates

M/S Modern builders

M/s Ram Associates

Deepesh Electricals

M/s Shrangi Rishi Construction