PROVISION OF ADMINISTRATIVE AND TRAINING INFRASTRUCTURE (PHASE- I) AT NDA KHADAKWASLA

Amount

SCH 'A' PART-I: BUILDING/STRUCTURES Note: This schedule is not pre-priced by MES and the rate indicated as "Rs 0.00" under Col 6 signifies this fact only

Construction of Block of Squadron building complete all as shown in drawings and as specified. Note:- (i) The work required for connecting two Squadron buildings as shown in Drawing No. ADG/2023/AR/004 Sheet 21/21 is outside the scope of the above building and shall be measured & paid separately under respective items of Schedule 'A' Part VIII. (ii) Health Faucet (THF), Shower rose and Pillar tap shall be measured and paid for seperately under respective items of Sch 'A'.

Construction of Block of Cycle Parking Shed (for 60 Cycles) alongwith Shoe Cleaning Shed and Cycle repair shed complete all as shown in drawings and as specified. Note:- Tap and GI pipe though shown in the drawing shall outside the scope of the above building and shall be measured & paid separately.

Construction of Block of Cycle Parking Shed (for 60 Cycles) alongwith Cycle Repair Shed complete all as shown in drawings and as specified.

Construction of Block of Cycle Parking Shed (for 60 Cycles) alongwith Shoe Cleaning Shed complete all as shown in drawings and as specified. Note:- Tap and GI pipe though shown in the drawing shall outside the scope of the above building and shall be measured & paid separately.

Construction of Block of Md JCO's Accn with Car Garage complete all as shown in drawings and as specified.

Construction of Md JCO's Accn with Scooter Parking complete all as shown in drawings and as specified.

Construction of Block of Single JCO's Accn for 02 JCOs with Scooter shed complete all as shown in drawings and as specified.

Construction of Block of Stables including allied buildings as mentioned below complete all as shown in drawing No. CEPZ/2023/KDK/02(H) sheet 1/4 and connected drawings and as specified :- (i) Block of Stable for 13 Horses :04 Nos (ii) Block of Harness store including ramp : 01 No (iii) Block of Forage Block & Boiling House including steps : 01 No (iv) Block of Forge and Shoeing Shed, Blacksmith, Saddlers and Carpenter's Shop & Clipping Shed including ramp: 01 No (v) Block of Open standing for 52 horses (consisting of 06 blocks) includung 2 Nos over head tanks with staging as per TD drawing No. CEPZ/2015/TD/02/STR Sheet 1/1. Notes: (a) Refer Drawing series Nos CEPZ/2023/KDK/02(H), CEPZ/2023/KDK/02(J) , CEPZ/2023/KDK/02(K) and connected drawings for construction of above buildings. (b) The buidings mentioned at srl No 1.08 (i) to (v) shall be considered as 'One Block' and bidders are requiredto qoute their rates considering as item. (c) Road and Paved Path way though shown in drawing No. CEPZ/2023/KDK/02(H) sheet 1/4 shall be out side the scope of above item and shall be measured and paid seperately.

Construction of Block of Boxes for sick line for 18 Horses complete all as shown in drawings and as specified.

Construction of Block of Open Standing for Sick line for 09 Horses complete all as shown in drawing No. CEPZ/2023/KDK/02(M) sheet 1/1 and connected drawings and as specified.

Construction of Block of Accn for Sick Line (consisting of Ration Store, Dispensary, Dressing Room and Attendent Room) including ramp and steps complete all as shown in drawing in drawing No. CEPZ/2023/KDK/02(M) sheet 1/1 and connected drawings and as specified.

Construction of Block of Addl Kitchen for Cadet Mess including open Court Yard complete all as shown in drawings and as specified.

Construction of Block of Group 'D' Md Accn (Type I) consisting of six quarters complete all as shown in drawings and as specified.

Construction of Block of Group 'D' Md Accn (Type I) consisting of five quarters complete all as shown in drawings and as specified.

Construction of Block of Scooter Shed (Parking for 06 Scooters.) with ramp complete all as shown in drawings and as specified.

Construction of Block of Scooter Shed (Parking for 05 Scooters.) with ramp complete all as shown in drawings and as specified.

Construction of Block of Scooter Shed (Parking for 12 Scooters.) with ramp complete all as shown in drawings and as specified.

Construction of Block of Married Accn for service officer (Maj and above) with Garage complete all as shown in drawings and as specified.

Construction of Block of Servant Quarter complete all as shown in drawings and as specified.

Construction of Block of Military Hospital (20 Beded) complete all as shown in drawings and as specified.

Construction of Block of Fire fighting Pump house and Fire fighting storage tank (50KL) complete all as shown on drawing Nos CEPZ/2023/KDK/02(V) sheet 1/2 & 2/2.

NOTE: Schedule ‘A’ Part II to XIV items have been Prepriced by MES and the Bidders shall insert their lumpsum cost in green field under Column-6 only.

Total amount of Sch 'A' Part-II (Internal Water Supply)

Total amount of Sch 'A' Part-III (Internal Electric Supply)

Total amount of Sch 'A' Part-IV (Rain Water Harvesting)

Total amount of Sch 'A' Part-V (Road, Path and Culvert)

Total amount of Sch 'A' Part-VI (Area Drainage and Nallah Diversion)

Total amount of Sch 'A' Part-VII (Sewage Disposal)

Total amount of Sch 'A' Part-VIII (Retaining wall, Arch, Fencing and Gate)

Total amount of Sch 'A' Part-IX (External Water Supply)

Total amount of Sch 'A' Part-X (External Electric Supply)

Total amount of Sch 'A' Part-XI (Lightning protection)

Total amount of Sch 'A' Part-XII (Cooling appliances)

Total amount of Sch 'A' Part-XIII(Fire fighting system)

Total amount of Sch 'A' Part-XIV (Site Clearance, Excavation and Earthwork)

NOTE: Schedule ‘A’ Part II to XIV items which are not Prepriced by MES are given in Sch 'A' Part-XV, Bidders shall insert their rate in Column-6 only and the Estimated rate indicated as "0.0" are for that purpose.

SCHEDULE 'A' PART-XV (MISC B/R AND E/M WORKS)

Suuply and fix 15mm bore Angle stop cock cast copper alloy chromium plated, fancy type screwed down high pressure with wall flange, complete all as specified and directed. MAKE :- Jaquar, Cat No. CON-059KN or techno commercially equivalent model in makes as per Appendix 'C'.

Supply and fix Wall Mixer with provision for Overhead Shower with 115mm long bend pipe on upper side, connecting legs and wall flanges complete all as specified and as directed. MAKE :- Jaquar, Cat No. CON-273KNUPR or techno commercially equivalent model in makes as per Appendix 'C'.

Supply and fix Sink Mixer with swinging spout (wall mounted model) with connecting legs and wall flanges complete all as specified and as directed. MAKE :- Jaquar, Cat No. CON-309KNM or techno commercially equivalent model in makes as per Appendix 'C'.

Supply and fix Central hole basin mixer without popup waste system with 450mm long braided hoses complete all as specified and as directed. MAKE :- Jaquar, Cat No. CON-167KNB or techno commercially equivalent model in makes as per Appendix 'C'.

Supply and fix Two way Bib cock for 15 mm bore pipe, cast copper alloy fancy type chromium plated complete all as specified and as directed. MAKE :- Jaquar, Cat No. CON-041KN or techno commercially equivalent model in makes as per Appendix 'C'.

Supply and fix Gun-metal, globe or gate valve for 75mm bore CPVC pipe with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed of makes as per Appendix 'C'.

Supply and fix Health Faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 m long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed. MAKE :- Jaquar Cat Part No. ALD 577 or techno commercially equivalent model as per Appendix 'C'.

Supply and fix LED light fittings, 20 Watt, 220V, AC, 4 feet tube light fitting, extruded polycarbonate housing and robust construction, LED lighting with not less than 100 lumen/Watt output, environmental friendly, energy efficient CRI-6500K, PF not less than 0.95, fixed on PVC square for mounting the fitting and electrically connecting with twin core 23/0.0076 PVC insulated multi stranded copper flexible cable from ceiling rose to light fitting (connector of lamp fitting) and one for earthing complete all as specified and as directed. MAKE :- Havells Model LHEXBLP7PN1W020 / BENLO Cat No. BLO4BAT20WT5 / Halonix Cat No. HLB-08-20-CW-IP.

Supply and fix surface mounted 9/10 watts, 2 feet tube light fitting, extruded polycarbonate housing and robust construction, LED lighting with lumen output, enviormental friendly, energy efficient CRI-6500K, PF not less than 0.95, fixed on PVC square box mounting the fitting and electrically connecting with twin core 23/0.0076 PVC insulated multistanded copper flexible cable from ceiling rose to light fitting (connector of lamp fitting) and one for earthing complete all as specified and as directed. MAKE :- Havells Model LHEXBLP7IN1W009 /HALONIX Cat No. HLB-07-10-CW-IP / Wipro Cat No. LL20-111-XXX-65 NE3 **6500K

Supply and fix LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V, AC, surface type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp suitable for roof ceiling including connecting up with driver, twin core 23/0.0076 PVC insulated multistanded copper flexible cable from ceiling rose to light fitting (connector of lamp fitting) and one for earthing complete all as specified and as directed. MAKE :- Havells Cat No. PLANOSUR2X2PLS36WLED857S0720 / Wipro Cat No. CRCO10S038HP57GL1 /Halonix Cat No. HLFPS22-02-36-CW-R-HL1

Supply and fix LED Security light fitting, 20 Watt, 230 V, AC, outdoor type with high pressure die cast aluminum hoUsing and heat resistant complete with driver, three core flexible copper conductor cable of suitable size with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection all as specified and as directed. MAKE :- Wipro Cat No. LR02-261-XXX-57-XX / Havells Model LHEXAYP7PN6K020 / Halonix Cat No. HLSLD-09H-20-CWL-R

Supply and fix LED street light fittings, 35 /36 Watt, 230 V, AC, outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, three core flexible copper conductor cable of suitable size with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection all as speckified and as directed. MAKE :- Philips Cat No. BRP030 LED35 CW MR PSU GR DX / Bajaj Cat No. ENXT P35L WH PO PC SD / Crompton Cat No. TRP-400-35-57-SL-LM-NSR.

Supply and fix street light bracket made out of 40 mm dia light grade GI pipe duly bent by hot forging for a length of 1.20 Mtr including two pairs of MS flat iron strip 35 mm x 4 mm clamps of suitable size with necessary GI nuts 75 mm in length 12 mm dia-04 Nos with flat washers, 3 mm thick -04 Nos, including painting with aluminium paint over one coat of red oxide primer to the MS clamps and braket etc., complete and fixing on wall /poles all as specified and as directed.

Supply and fix sheet metal enclosures, double door, for DBs when MCBs to be used single pole and neutral 240 volts 6 way IP-43 protection with not less than 100 Amps rated bus bar fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs / thimbles duly crimped for connection complete all as specified and as directed.

Supply and fix MCB DB VTPN 4 way, metal double door load line powder coated IP-43 protection with provision for 4 pole MCCB as incomer and SP/TP MCBs as outgoings complete, provided with insulated vertical phase bus bars neutral bars with shrouds, earth bars, sticking saddles, cement spill protector, colour-coded inter connecting wire set, cable ties, blanking plates and circuit identification labels, fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection complete all as specified and as directed. NOTE :- MCCBs shall be measured and paid seperately.

Supply and fix MCB DB VTPN 8 way, metal double door load line powder coated IP-43 protection with provision for 4 pole RCBOs as incomer and SP/TP MCBs as outgoings complete provided with insulated vertical phase bus-bars, neutral bars with shrouds, earth bars, sticking saddles, cement spill protector, colour-coded interconnecting wire set, cable ties, blanking plates and circuit identification labels, fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs / thimbles duly crimped for connection complete all as specified and as directed. NOTE :- RCBO shall be measured and paid seperately.

Supply and fix MCB DB VTPN 4 way, metal double door load line powder coated IP-43 protection with provision for 4 pole RCBOs as incomer and SP/TP MCBs as outgoings complete provided with insulated vertical phase bus-bars neutral bars with shrouds, earth bars, sticking saddles, cement spill protector, colour-coded interconnecting wire set, cable ties, blanking plates and circuit identification labels, fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs / thimbles duly crimped for connection complete all as specified and as directed. NOTE :- RCBO shall be measured and paid seperately.

Supply and fix RCBO 100 Amps, 415 Volts, 12 Modules, 10 KA, 4 pole fixed on VTPN 8 Way DB in and including copper lugs /thimbles of size as per wire / cable including crimping for connection, testing and commissioning complete all as specified and as directed.

Supply and fix RCBO 40 Amps, 415 Volts, 12 Modules, 10 KA, 4 pole fixed on VTPN 8 Way DB in and including copper lugs / thimbles of size as per wire/cable including crimping for connection, testing and commissioning complete all as specified and as directed.

Supply and fix miniature circuit breaker (MCB) of single poles and neutral (SPN) /DP current carrying capacity 6 to 32 Amps, 240V, 10 KA 'B' curve in and including copper lugs / thimbles of size as per wire / cable including crimping for connection, testing and commissioning complete all as specified and as directed.

Supply and fix miniature circuit breaker (MCB) of single pole and neutral (SPN) / DP current carrying capacity 40 to 100 Amps, 240V, 10 KA, 'B' curve, in and including copper lugs / thimbles of size as per wire / cable including crimping for connection, testing and commissioning complete all as specified and as directed. NOTE FOR SRL ITEM NO. 15.18 & 15.19 :- (i) MCBs, MCCB's shall be measured and paid for separately under respective items. (ii) MCB DB & MCBs, Isolator, RCBO shall be of uniform make.

Supply and fix blank MCB plates all as specified and as directed.

Material and labour for earthing with 600x600x6mm galvanised steel earth plate electrode buried vertically in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the plate at a depth of not less than 1.5m below ground level, connected to and including GI wire of size 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised steel, GI pipe 15 mm dia light grade pipe for protection of GI earth lead wire both to be provided to the extent of 7.5 metres as earthing lead and connecting to the eqpt / machinery etc., including charcoal dust and common salt packed all around the earth plate in alternate layers in the earth pit all as per electrical plate No. 3 of SSR Part I-2009 including PCC chamber made up of PCC (1:3:6), type C1 and RCC chamer cover of size 540x540x100 mm made with RCC (1:2:4), type B1, using 8 mm dia TMT steel bars and 10 mm dia MS round bar for handle, 20 mm dia medium grade GI watering pipe from top edge of the earth plate upto MS funnel with wire mesh provided inside the concrete earth pit for watering arrangement including excavation and earth work in any type of soil and testing complete all as specified and as directed.

Supply and installation weather proof polycarbonate Meter box suitable for single phase smart energy meter, including bolts, nuts, washers clamps, fastners etc., complete all as specified and as directed.

Supply installtion weather proof poly carbonate Meter box suitable for three Phase smart energy meter, including bolts, nuts, washers, clamps, fastners etc., complete all as speified and as directed.

Material and labour 200 mm thick (compacted thickness) Granular Sub Base (GSB) of Grade I as per table 400-1 of MORT&H, IRC specification laid with mechanical pavers, rolled and compacted to required gradient and camber with 8 to 10 tonne power roller and vibratory roller complete as per MORT&H specification clause-401 including all tools and plants etc., complete all as specified and as directed.

M&L 250mm thick (compacted thickness) Wet Mix Macadam (WMM) laid in two layers, as per MORT&H specifications (Table 400-II), using crusher broken graded stone aggregates (Basalt /trap /granite), pre-mixing the material with water at OMC in mechanical mixer (pug mill), carriage of mixed material by tippers to site, laid in uniform layer over prepared sub base /base course using mechanical paver and rolled and compacted to required gradient and camber with 8 to 10 tonne power vibratory roller to achieve the desired density, complete as per MORTH specification clause-406, complete including all material, labour, machinery, lighting, guarding and maintenance of diversion, all as specified and as directed.

Providing and applying thermoplastic reflective paint of any colour as approved for traffic lane strips 100/150mm wide and 2mm thick of pigment 10% on clean dry and good road surface with 10% glass beads, 20% binder, 10% extender and 60% of filler materials all as per IRC complete all as specified and as directed.

Supply and fixing metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed. (Makes - Siddhi Vinayak Enterprises / Road Safety Mark / Dark Eye / Alaxius / 3M / Greenlite).

S&F Cat eye solar reflective type of metal body alloy of size 10mm x 100mm x 20mm with PAMA strip lens reflector of model No. DA 972 fixed with and incl MS stud of suitable size as per manufacturer's instructions complete all as specified and directed. (Makes - Siddhi Vinayak Enterprises / Road Safety Mark / Dark Eye / Alaxius / 3M / Greenlite).

S&F Solar cat eye aluminium alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono crystafine solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600 MA) consisting of super bright LED with 10,000 to 18,000 mcd complete as per manufacturer's instructions complete all as specified and directed. (Makes - Siddhi Vinayak Enterprises / Road Safety Mark / Dark Eye / Alaxius / 3M / Greenlite).

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bilingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of mild steel angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. mild steel angles of size 35x35x5 mm to a vertical post made up to mild steel Tee section of ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles, flats, providing and fixing mild steel message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours), backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts complete all as specified and as directed.

Supply, laying, jointing and testing Ductile iron pipes, K7 class with spigot and socket, suitable for push on rubber joint, with internal cement mortor lining, and external zinc and black bitumen coated pipes in any lengths conforming to IS:8329-2000 including rubber gasket & joints as per IS:9523-2000 laid in trenches/ road/ ducts/ footpath / on wall / on floor locations of size 100 mm dia pipe complete all as specified and as directed.

All as per Sl Item No. 15.33 above but 150 mm dia.

All as per Sl Item No. 15.33 above but 200 mm dia.

All as per Sl Item No. 15.33 above but 300 mm dia.

Material and labour for connecting pieces one end flanged and other end socket or spigot and bell mouth pieces one end flanged other end tapering as bell mouth, DI bends tapers, Tees, pieces (single or double branch) any type and angle/radius and straight connecting pieces for DI pipe of size 100 to 300 mm bore complete all as specified and as directed.

Supply and fix for Cast Iron sluice valve of size 65 mm bore dia with stainless steel spindle and cast iron hand wheel complying with IS:14846-2000, class PN 1.0 both ends flanged with and including two nos rubber insertion gasket joints, nuts, bolts & washers of required size and in required Nos complete all as specified and as directed.

All as per Sl Item No. 15.38 above but 80 mm dia.

All as per Sl Item No. 15.38 above but 100 mm dia.

All as per Sl Item No. 15.38 above but 150 mm dia.

All as per Sl Item No. 15.38 above but 200 mm dia.

All as per Sl Item No. 15.38 above but 300 mm dia.

Material and labour for cutting of roads upto 50 cm depth for laying of GI protection pipes of suitable size for cable and making good disturbed surfaces to match with existing finishes all as specified and as directed.

Supply and fix PP-R Gate valve (brass insert) of grade PN-25, SDR-7.4, 3 layered, (outer green coloured UV stabalized, middle black coloured UV stabalized, and inner most layer white coloured with antimicrobial property )fusion welded PP-R ( Polypropyelene random copolymer) gate valve brass, light weight ISI marked as per pre requirement of the site with handle screwed both ends for PP-R pipes of outer dia 20 mm or for unions complete all as specified and as directed.

All as per Sl Item No. 15.45 above but size 25mm dia.

All as per Sl Item No. 15.45 above but size 32 mm dia.

Supply and fix Cast Iron Air Valves with two air outlets conforming to IS-14845 of size 200 mm dia bore and fixing up in cast iron water supply mains of size 200mm did complete all as specified and as directed.

Material and labour for construction of brick masonry valve chamber of size 600mm x 600mm x 600mm (internal dimensions) to accomadate 40 mm to 100mm bore size valves of any type, with 150mm thick foundation using PCC (1:3:6), type C-2, using 40mm graded stone aggregate over 150mm thick hardcore, 230mm thick brick wall built in cement and sand mortar (1:4), 15mm thick internal and external plaster including top of floor in cement and sand mortar(1:3) finished even and smooth without using extra cement, 10mm thick MS sheet cover with, 50mm x 50mm x 6mm MS angle iron frame embeded in PCC (1:2:4), type B1, using 20mm graded stone aggregate as in coping having rectangular hinged opening of suitable size with locking arrangements & handle made out of 25mm dia MS round bar, hold fasts etc applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surfaces including excavation and earth work in any type of soil and disposal of surplus soil to a distance n.exc 50m complete all as specified and as directed.

Material and labour for construction of brick masonry valve chamber of size 900mm x 900mm x 900mm (internal dimensions) to accomadate 150 mm to 200mm bore size valves of any type, with 150mm thick foundation using PCC (1:3:6), type C-2, using 40mm graded stone aggregate over 150mm thick hardcore, 230mm thick brick wall built in cement and sand mortar (1:4), 15mm thick internal and external plaster including top of floor in cement and sand mortar(1:3) finished even and smooth without using extra cement, 10mm thick MS sheet cover with, 50mm x 50mm x 6mm MS angle iron frame embeded in PCC (1:2:4), type B1, using 20mm graded stone aggregate as in coping having rectangular hinged opening of suitable size with locking arrangements & handle made out of 25mm dia MS round bar, hold fasts etc applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surfaces including excavation and earth work in any type of soil and disposal of surplus soil to a distance n.exc 50m complete all as specified and as directed.

Material and labour for construction of brick masonry valve chamber of size 1200mm x 1200mm x 1200mm (internal dimensions) to accomadate 300mm bore size valves of any type, with 150mm thick foundation using PCC (1:3:6), type C-2, using 40mm graded stone aggregate over 150mm thick hardcore, 230mm thick brick wall built in cement and sand mortar (1:4), 15mm thick internal and external plaster including top of floor in cement and sand mortar(1:3) finished even and smooth without using extra cement, 10mm thick MS sheet cover with, 50mm x 50mm x 6mm MS angle iron frame embeded in PCC (1:2:4), type B1, using 20mm graded stone aggregate as in coping having rectangular hinged opening of suitable size with locking arrangements & handle made out of 25mm dia MS round bar, hold fasts etc applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surfaces including excavation and earth work in any type of soil and disposal of surplus soil to a distance n.exc 50m complete all as specified and as directed.

Material and labour for cutting cast iron pipes of 100mm dia and reducing to required length including fixing of fittings such as tail piece, Tees and necessary run lead joint including caulking, flanged joint, jointing material like lead,rubber gasket, nut, bolt and washers complete all as specified and as directed. NOTE :- Fittings shall be measured and paid separately under relevent items of BOQ

All as per Sl Item No. 15.52 above but size of pipe 150 mm dia.

All as per Sl Item No. 15.52 above but size of pipe 300 mm dia.

All as per Sl Item No. 15.52 above but size of pipe 450 mm dia.

Material and labour for cutting the existing GI pipes of size 80mm dia for insertion of 20mm connection and reducing to required length including fixing of fittings such as Tees, elbows, nipples, washers etc., complete including excavation, earth work, refilling required at site all as directed.

Material and labour for cutting the existing GI pipes of size 50mm dia for insertion of 20mm connection and reducing to required length including fixing of fittings such as Tees elbows, nipples etc. washers complete including excavation, earth work, refilling required at site all as directed.

Material and labour for drilling and tapping cast iron water mains (in position) for branch connections of the internal dia 25 mm all as specified and as directed.

Supply, install, testing and commissioning of vertical type openwell submersible pump of capacity 10-90 LPM, head 30-5.5 meter single phase 3 stage of size 25 mm x 25mm ( suction discharge ) with DOL starter in sheet steel enclosure, relay range 9-14 Amps and necessary copper cable of 4 sq.mm x 2 core complete all as specified and as directed.

Supply and fix Gang operated air break switch, off load disconnecting switch 11 KV, 200 Amps with 12 insulators, triple pole, each pole consisting of galvanised steel base HT insulator as per BSS/ISS non-ferrous knife and spring loaded contacts, arching arms of adequate section to break magnetising current complete with square shaft of GI, adequate length for phase separation, operating handle complete with locking arrangement with lock and key in both "OFF" and "ON" position, with suitable clamp, nuts, bolts complete for fixing on the channel, making all electric connections / jumpers with bottle lugs commissioning and testing complete along with supply and fix new drop out expulsion fuse HT 11 KV grade rating up to 50 Amps mounted on insulator and steel frame complete all heavy duty fuse barrel with fuse element complete set conforming to IS: 1818 as specified and as directed.

Design, fabricating, supply, errecting connecting and testing totally enclosed LT cubicle panel board, 3 Phase, 4 wire system, outdoor, double door front and back opening type, sloped canopy (hood) on top extended 100 mm all arround, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cables in and out, incoming and out going feeders duly marked on riveted plates etc., complete CPRI type tested factory made, fabricated out of 3mm thick CRCA sheet duly treated through 8 tank pre treatment process and painted with epoxy powder coated matt finish of SIEMENS GREY structural RAL 7032 shade colour, built in industrial type locking arrangements on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, panel mounted on angle iron frame of sutable size duly painted and embeded in PCC (1:3:6), 45 cm below ground level and 45cm above ground level and consisting of following items :-

BUSBAR CHAMBER :- Electrically grade bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic, non combustible, track resistant high strength FRP insulators for phases and neural set of 4 for RYB &N -01 set.

Incoming :-

(a) MCCB Four Pole 415 Volts 50 Hz 63 Amps of 16 KA,Ics=100% of Icu thermal magnetic release , adjustable Overload Setting, protection against overload / shortcircuits, inbuilt instantaneous proctection - 01 No.

(b) Multifunctional Meter to read V,A,HZ etc -01 No

(c) Indicator LED Type for RYB set of 3 - 01 set

Outgoing :-

(i) MCB 16 Amps, 4 Pole,415V, 50Hz 10 KA - 08 Nos. ( 01 No.each one for 07 Nos. Qtrs,& 01 Spare).

(ii) MCB 4 pole 16 A (Street light ) - 01 No.

(iii) MCB SP 6 A (Street light timer ) - 01 No.

(iv) Astronomical Time switch - 01 No.

(v) Power contactor 3 pole AC, with 230V coil, 9 amps AC1 rating - 01 No.

Design, fabricating supply, errecting, connecting and testing totally enclosed LT cubicle panel board, 3 Phase, 4 wire system, outdoor, double door front and back opening type, sloped canopy (hood) on top extended 100 mm all arround, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cables in and out, incoming and out going feeders duly marked on riveted plates etc., complete CPRI type tested factory made fabricated out of 3mm thick CRCA sheet duly treated through 8 tank pre treatment process and painted with epoxy powder coated matt finish of SIEMENS GREY structural RAL 7032 shade colour, built in industrial type locking arrangements on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs ,panel mounted on angle iron frame of sutable size duly painted and embeded in PCC (1:3:6) 45 Cm below ground level and 45 Cm above ground level and consisting of following items :-

BUSBAR CHAMBER : Electrically grade Bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic,non combustible,track resistant high strength FRP insulators for phases and neural set of 4 for RYB &N -01 set

Incoming

(a) MCCB four pole 415 Volts 50 Hz 400Amps (Relay Range 320-400 A) repturing capacity of 35 KA ,Ics=100% of Icu , with thermal magnetic protection system, thermal adjustable, protection against overload/shortcircuits, inbuilt instantaneous proctection, Over temperature alarm indication, integrated contact module for status indication - 01 No.

(b) Multifunctional Meter to read V,A,HZ etc -01 No

(c) Indicator LED Type for RYB set of 3 - 01 set

Outgoing-

(i) MCCB Four Pole 415 Volts 50 Hz 200 Amps 25KA ,Ics=100% of Icu with thermal magnetic protection system, thermal adjustable, protection against overload / short circuits, inbuilt instantaneous proctection, Over temperature alarm indication, integrated contact module for status indication - 04 No. (Sub panel 1,2,3 + 01 Spare )

(ii) MCB 4 pole 16 A (Street light ) - 01 No

(iv) MCB SP 6 A (Street light timer ) - 01 No

(v) Astronomical Time switch - 01 No

(vi) Power contactor 3 pole AC, with 230V coil, 9 amps AC1 rating - 01 No

Design, fabricating, supply, errecting, connecting and testing totally enclosed LT cubicle panel board, 3 phase, 4 wire system, outdoor, double door front and back opening type, sloped canopy (hood) on top extended 100 mm all arround, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cables in and out, incoming and out going feeders duly marked on riveted plates etc., complete CPRI type tested factory made, fabricated out of 3mm thick CRCA sheet duly treated through 8 tank pre treatment process and painted with epoxy powder coated matt finish of SIEMENS GREY structural RAL 7032 shade colour, built in industrial type locking arrangement on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, panel mounted on angle iron frame of sutable size duly painted and embeded in PCC (1:3:6) 45 Cm below ground level and 45 Cm above ground level and consisting of following items :-

BUSBAR CHAMBER : Electrically grade Bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic,non combustible,track resistant high strength FRP insulators for phases and neural set of 4 for RYB &N -01 set

Incoming

(a) MCCB 200Amps, TPN, 415V, 50Hz 25 KA, Ics=100% of Icu with thermal magnetic protection system, thermal adjustable, protection against over load / short circuits, inbuilt instantaneous protection, over temperature alarm indication, integrated contact module for status indication - 01. No.(Incoming)

(b) Multifunctional Meter to read V, A, Hz etc -01 No

(c) Indicator LED Type for RYB set of 3 - 01 set

Outgoing-

(i) MCB 63 Amps, TPN, 415V, 50Hz 10 KA - 7 Nos (01 Spare)

Design, fabricating, supply, errecting connecting and testing totally enclosed LT cubicle panel board 3 Phase 4 wire system outdoor double door front and back opening type, sloped canopy (Hood) on top extended 100 mm all arround ,separate compartment for each control gear,cable alley, provision of knock out type plates for various sizes of cables in and out , incoming and out going feeders duly marked on riveted plates etc., complete CPRI type tested factory made fabricated out of 3mm thick CRCA sheet duly treated through 8 tank pre treatment process and painted with epoxy powder coated mat finish of SIEMENS GREY structural RAL 7032 shade colour,built in industrial type locking arrangement on front and back ,and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs ,Panel mounted on Angle iron frame of sutable size duly painted and embeded in PCC 1:3:6 45 CM below ground level and 45 Cm above ground level and consisting of following items :-

BUSBAR CHAMBER : Electrically grade Bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic,non combustible,track resistant high strength FRP insulators for phases and neural set of 4 for RYB & N - 01 Set

Incoming

(a) MCCB 200 Amps, 4 pole , 415V, 50Hz 25 KA ,Ics=100% of Icu with thermal magnetic protection system, thermal adjustable, protection against overload/shortcircuits, inbuilt instantaneous proctection, Over temperature alarm indication, integrated contact module for status indication - 01 No.(Incoming)

(b) Multifunctional Meter to read V,A,HZ etc -01 No

(c) Indicator LED Type for RYB set of 3 - 01 set

Outgoing-

(i) MCB 40 Amps, TPN, 415V, 50Hz 10 KA - 1No

(ii) MCB 63 Amps, TPN, 415V, 50Hz 10 KA - 7 No (including 01 No spare)

Design, fabricating, supply, errecting, connecting and testing totally enclosed LT cubicle panel board, 3 Phase, 4 wire system, outdoor, double door front and back opening type, sloped canopy (hood) on top extended 100 mm all arround, separate compartment for each control gear,cable alley, provision of knock out type plates for various sizes of cables in and out , incoming and out going feeders duly marked on riveted plates etc., complete CPRI type tested factory made fabricated out of 3mm thick CRCA sheet duly treated through 8 tank pre treatment process and painted with epoxy powder coated matt finish of SIEMENS GREY structural RAL 7032 shade colour, built in industrial type locking arrangements on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, panel mounted on angle iron frame of sutable size duly painted and embeded in PCC (1:3:6), 45Cm below ground level and 45Cm above ground level and consisting of following items :-

BUSBAR CHAMBER : Electrically grade bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic, non combustible, track resistant, high strength FRP insulators for phases and neural set of 4 for RYB & N - 01 set

Incoming :-

(a) MCCB four pole, 415 Volts, 50 Hz, 400Amps rapturing capacity of 35 KA, Ics=100% of Icu with thermal magnetic protection system, thermal adjustable, protection against overload / shortcircuits, inbuilt instantaneous proctection, Over temperature alarm indication, integrated contact module for status indication - 01No

(b) Multifunctional Meter to read V,A,HZ etc -01 No

(c) Indicator LED Type for RYB set of 3 - 01 set

Outgoing-

(i) MCCB Four Pole 415 Volts 50 Hz 100Amps adjustable type with rupturing capacity of 16KA - 05 No ( 01 No. For subpanel 1,2,3 and 4 & one No. spare)

(ii) MCB 4 Pole 16 A (Street light ) - 01 No

(iii) MCB SP 6 A (Street light timer ) - 01 No

(iv) Astronomical Time switch - 01 No

(v) Power contactor 3 pole AC, with 230V coil, 9 ampsAC1 rating - 01 No

Design, fabricating, supply, errecting, connecting and testing totally enclosed LT cubicle panel board, 3 Phase, 4 wire system, outdoor, double door front and back opening type, sloped canopy (hood) on top extended 100 mm all arround, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cables in and out , incoming and out going feeders duly marked on riveted plates etc., complete CPRI type tested factory made, fabricated out of 3mm thick CRCA sheet duly treated through 8 tank pre treatment process and painted with epoxy powder coated matt finish of SIEMENS GREY structural RAL 7032 shade colour, built in industrial type locking arrangements on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, panel mounted on angle iron frame of sutable size duly painted and embeded in PCC (1:3:6), 45 Cm below ground level and 45 Cm above ground level and consisting of following items :-

BUSBAR CHAMBER : Electrically grade bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic, non combustible, track resistant high strength FRP insulators for phases and neural set of 4 for RYB &N -01 set.

Incoming :-

(a) MCCB 100 Amps, 4 pole, 415V, 50Hz, 25 KA, Ics=100% of Icu, Ics=100% of Icu, with thermal magnetic protection system, thermal adjustable, protection against overload / short circuits, inbuilt instantaneous proctection, over temperature alarm indication, integrated contact module for status indication - 01 No.(Incoming).

(b) Multifunctional Meter to read V,A,HZ etc -01 No

(c) Indicator LED Type for RYB set of 3 - 01 set

Outgoing :-

(i) MCB 32 Amps, TPN, 415V, 50Hz 10 KA- 7 No ( 01 No. for each qtrs (6qtrs =6 Nos.) and one spare)

Design, fabricating, supply, errecting, connecting and testing totally enclosed LT cubicle panel board, 3 Phase, 4 wire system, outdoor, double door front and back opening type, sloped canopy (hood) on top extended 100 mm all arround, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cables in and out, incoming and out going feeders duly marked on riveted plates etc., complete CPRI type tested factory made, fabricated out of 3mm thick CRCA sheet duly treated through 8 tank pre treatment process and painted with epoxy powder coated matt finish of SIEMENS GREY structural RAL 7032 shade colour, built in industrial type locking arrangements on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, panel mounted on angle iron frame of sutable size duly painted and embeded in PCC (1:3:6) 45 Cm below ground level and 45 Cm above ground level and consisting of following items :-

BUSBAR CHAMBER : Electrically grade bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic, non combustible, track resistant high strength FRP insulators for phases and neural set of 4 for RYB &N -01 set

Incoming :-

(a) MCCB 100 Amps, 4 Pole, 415V, 50Hz 25 KA F,Ics=100% of Icu, Ics=100% of Icu, with thermal magnetic protection system, thermal adjustable, protection against overload / shortcircuits, inbuilt instantaneous protection, over temperature alarm indication, integrated contact module for status indication - 01 No.(Incoming).

(b) Multifunctional Meter to read V,A,HZ etc -01 No

(c) Indicator LED Type for RYB set of 3 - 01 set

Outgoing :-

(i) MCB 32 Amps, TPN, 415V, 50Hz 10 KA - 6 No ( 01 No. for each qtrs (5qtrs =5 Nos.) and one spare)

Design, fabricating, supply, errecting, connecting and testing totally enclosed LT cubicle panel board, 3 Phase, 4 wire system, outdoor, double door front and back opening type, sloped canopy (hood) on top extended 100 mm all arround, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cables in and out, incoming and out going feeders duly marked on riveted plates etc., complete CPRI type tested, factory made, fabricated out of 3mm thick CRCA sheet duly treated through 8 tank pre treatment process and painted with epoxy powder coated matt finish of SIEMENS GREY structural RAL 7032 shade colour, built in industrial type locking arrangement on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, panel mounted on angle iron frame of sutable size duly painted and embeded in PCC (1:3:6), 45Cm below ground level and 45Cm above ground level and consisting of following items :-

BUSBAR CHAMBER : Electrically grade bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic, non combustible, track resistant high strength FRP insulators for phases and neural set of 4 for RYB &N -01 set.

Incoming :-

(a) ACB 415 Volt 4 Pole, capacity 800Amps, 50 KA Manual drawout type - 01 No. (Incoming)

(b) Multifunctional Meter to read V,A,HZ etc -01 No

(c) Indicator LED Type for RYB set of 3 - 01 set

Outgoing :-

(i) MCCB 250 Amps, 4 Pole, 415V, 50Hz, 25 KA, Ics=100% of Icu with thermal magnetic protection system , Thermal adjustable Overload Setting, protection against overload/shortcircuits, inbuilt instantaneous proctection - 05 No ( 4 Nos for sqn 1,2,3 & 4 and 01 spare)

(ii) MCCB 160 Amps, 4 Pole, 415V, 50Hz, 25 KA, Ics=100% of Icu with thermal magnetic protection system, thermal adjustable, protection against overload /short circuits, inbuilt instantaneous proctection, over temperature alarm indication, integrated contact module for status indication - 01 No ( Fire Fighting)

(iii) MCB 4 pole, 16 Amps,10 KA (street light ) - 01 No

(iii) MCB SP 6 A ,10 KA(Street light timer) - 01 No

(iv) Astronomical Time switch - 01 No

(v) Power contactor 3 pole AC, with 230V coil, 9 Amps AC1 rating - 01 No

Design, fabricating, supply, errecting, connecting and testing totally enclosed LT cubicle panel board, 3 Phase, 4 wire system, outdoor, double door, front and back opening type, sloped canopy (hood) on top extended 100 mm all arround, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cables in and out, incoming and out going feeders duly marked on riveted plates etc., complete CPRI type tested, factory made, fabricated out of 3mm thick CRCA sheet duly treated through 8 tank pre treatment process and painted with epoxy powder coated matt finish of SIEMENS GREY structural RAL 7032 shade colour, built in industrial type locking arrangements on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, panel mounted on angle iron frame of sutable size duly painted and embeded in PCC (1:3:6) 45 Cm below ground level and 45 Cm above ground level and consisting of following items :-

BUSBAR CHAMBER : Electrically grade bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic,non combustible, track resistant high strength FRP insulators for phases and neural set of 4 for RYB &N -01 set.

Incoming :-

(A) MCCB 250 Amps, 4 Pole 415V, 50Hz, 36 KA , Ics=100% of Icu with thermal magnetic protection system, thermal adjustable, protection against overload / short circuits, inbuilt instantaneous proctection, over temperature alarm indication, integrated contact module for status indication - 01 No . (Incoming)

(b) Multifunctional Meter to read V,A,HZ etc -01 No

(c) Indicator LED Type for RYB set of 3 - 01 set

Outgoing :-

(i) MCCB Four Pole 415 Volts 50 Hz 100 Amps ,Ics=100% of Icu thermal magnetic release adjustable, adjustable overload setting, protection against overload / short circuits, inbuilt instantaneous proctection - 04 No ( Each for Ground Floor, First Floor , Second Floor and 01 No. Spare)

(ii) MCCB Four Pole 415 Volts 50 Hz 63 Amps adjustable type with repturing capacity of 16 KA - 02 No ( (Solar water heating system)

Supply, installation, commissioning and testing of panel of suitable size, factory made, CPRI type tested, outdoor, cubical compartmental type, double door, both side openable with hinged doors & locking arrangement, made out of 3.15 mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron of size 50 mm x 50 mm x 6 mm, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (8 tank process), duly fixed in ground with PCC foundation (1:2:4) type B1, with danger notice plate of 1.6 mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3- Phase 4 Wire system, 500 V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length size, including fixing lugs bolts, screws etc. all complete as specified and directed. (For Solar panel Sqn Bldg)

Busbar Chamber: Electrically grade Bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic,non combustible,track resistant high strength FRP insulators for phases and neural set of 4 for RYB &N -01 set

INCOMING

(a) MCCB 4 Pole 63 A,16 KA )-01 No

(b) Digital VAF meter 01No

(c) R,Y B Indicator lamp LED type - 01 Set

OUTGOING

(a) MCB SP 10 A (for heater) -08 Nos

(b) MCB SP 6 A (for heater and pressure pump) -01No

(c) Indicating lamp on -off for pump -02 Nos

NOTE FOR SERIAL ITEM NO 15.61 to 16.61 (a) Panel manufacturer should have in house powder coating plant with minimum 8 tanks pretreatment of MS sheet facilities, dust free spray paint booth. (8 tanks pretreatment process includes:degreasing / water rinsing /de-rusting / waterinshing / activation / phosphating / water rinsing / passivation). (b)Thickness of powder coating shall not be less than 80 microns and test certificate for powder coating shall be furnished along with LT panel. (c) Pre dispatch inspection shall be carried out by the authorized representative of Accepting Officer. In case of any deviation from approved drawing, the same shall be rejected and fresh LT panel shall be fabricated by the manufacturer. Testing shall be done at manufacturer 's premises and all routine test like IR and continuity tests shall be performed /recorded in presence of authorized representative of Accepting Officer. (d)All the electrical switchgear like MCCBs,MCBs and ACBs should be of same make. (e) Make of Panel Board shall be as per Appendix 'C'.

Material and labour for earthing with 600x600x6mm galvanised steel earth plate electrode buried vertically in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the plate at a depth of not less than 1.5m below ground level, connected to and including galvanised earth strip 32 mm x 6 mm by means of bolts, nuts, check nuts and washers of galvanised steel, GI pipe 40 mm dia light grade pipe for protection of GI earth strip both to be provided to the extent of 7.5 metres as earthing lead and connecting to the eqpt / machinery etc., including charcoal dust and common salt packed all around the earth plate in alternate layers in the earth pit all as per electrical plate No. 3 of SSR Part I-2009 including PCC chamber made up of PCC 1:3:6 type C1 & RCC Chamer cover of size 540x540x100 mm made with 1:2:4 Type B1 using 6 mm round MS bar & 8 mm MS bar for handle , 20 mm dia medium grade G.I. watering Pipe from top edge of the earth plate upto M.S. funnel with wire mesh provided inside the concrete earth pit for watering arrangement incl excavation and earth work in any type of soil and testing complete all as specified and as directed.

Material and labour for earthing with 600x600x6mm galvanised steel earth plate electrode buried vertically in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the plate at a depth of not less than 1.5m below ground level, connected to and including galvanised earth strip 25 mm x 4 mm by means of bolts, nuts, check nuts and washers of galvanised steel, GI pipe 40 mm dia light grade pipe for protection of GI earth strip both to be provided to the extent of 7.5 metres as earthing lead and connecting to the eqpt/machinery etc., including charcoal dust and common salt packed all around the earth plate in alternate layers in the earth pit all as per electrical plate No. 3 of SSR Part I-2009 including PCC chamber made up of PCC (1:3:6) type C1 & RCC Chamer cover of size 540x540x100 mm made with (1:2:4), type B1 using 6 mm dia round MS bar & 8 mm dia MS bar for handle, 20 mm dia medium grade GI watering pipe from top edge of the earth plate upto MS funnel with wire mesh provided inside the concrete earth pit for watering arrangement including excavation and earth work in any type of soil and testing complete all as specified and as directed.

Supply and fix Weather proof Street light Junction box 300 x 200 x 105 mm depth including MCB SP, 6 Amps, B curve and connecting terminals, 4 way and fixing with street light poles (steel) using necessary MS clamps, nuts, bolts washers of suitable size etc., including fixing arrangements complete all as specified and as directed.

Material and labour for boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 Mpa working pressure complete all as specified and as directed.

Supply and Install Refrigerator, electric driven (single phase), capacity 360 Litres or nearest size, BEE 3 star rated convertible plus with inverter linear compressor door cooling smart diagnosis, auto smart connect double door with Auto Power Factor Correction for stabiliser free operation complete with suitable PVC stand all as specified and as directed. Makes:- Samsung/ LG/ Whirlpool/ Godrej

Supply and fix Cast Iron Air Valves with two air outlets conforming to IS-14845 of size 100 mm dia bore and fixing up in cast iron water supply mains of size 100mm bore complete all as specified and as directed.

Supply, install, testing and commissioning Active Repeater with Full Function Control, Compatible with GST200 Series,GST5000 Series and GSt-IFP8 panel, additional network card need to be ordered all as directed.

Supply, installation, commissioning and testing of panel of suitable size, factory made, CPRI type tested, indoor, cubical compartmental type, double door, both side openable with hinged doors & locking arrangement, made out of 2 mm thick mild steel CRCA sheet, supported and fixed on structural frame angle iron of size 50 mm x 50 mm x 6 mm, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (8 tank process), duly fixed in ground with PCC foundation (1:2:4) type B1, with danger notice plate of 1.6 mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3- Phase, 4 Wire system, 500 V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length and size, including fixing lugs bolts, screws and including necessary switches, contactors, relays etc. of required size for auto operation making electric and engine operated pump set auto ON /OFF based on pressure switch, Rates for which is deemed to be included in the item rate.etc. all complete as specified and directed(at New Fire fighting Pump house) comprising of the following:-

Busbar Chamber: Electrically grade Bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic, non combustible, track resistant high strength FRP insulators for phases and neural set of 4 for RYB &N -01 set

INCOMING

(a) MCCB 4 Pole 100A,16 KA -01No

(b) Digital VAF meter 01No

(c) R,Y B Indicator lamp LED type - 01 Set

OUTGOING

(a) MCCB 4 Pole 80 A,18 KA -01No

(b) MCB SPN 20 A PH Lighting)-01No

(c) Star Delta Starter of capacity 50HP with single phase preventor- 01No

(d) ON /OFF Indicator lamp LED type - 02No

Supply, installation, commissioning and testing of panel of suitable size, factory made, CPRI type tested, outdoor, cubical compartmental type, double door, both side openable with hinged doors & locking arrangement, made out of 3.00 mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron of size 50 mm x 50 mm x 6 mm, including earthing stud, labeling, painting to all internal & external exposed steel surfaces with powder coating paint (8 tank process), duly fixed in ground with PCC foundation (1:2:4) type B1, with danger notice plate of 1.6 mm thick mild steel sheet, vitreous enameled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3- Phase 4 Wire system, 500 V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length size, including fixing lugs bolts, screws etc. all complete as specified and directed(at TERACE For each Booster Pump) comprising of the following :-

Busbar Chamber: Electrically grade Bus bar aluminium of capacity equal to 1.5 times of rated incoming control switch gear including interconnection of all switch gears duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic,non combustible, track resistant high strength FRP insulators for phases and neutral set of 4 for RYB &N -01 set

INCOMING

(a) MCCB 4 Pole20A,16 KA -01No

(b) Digital VAF meter 01No

(c) R,Y B Indicator lamp LED type - 01 Set

OUTGOING

(c) Star Delta Starter of capacity 15HP with single phase preventor- 01No

(d) ON /OFF Indicator lamp LED type - 02 No

Supply and lay PVC Insulated & sheathed copper conductor single core cable of size 10 sq.mm x single core all as specified and as directed.

Supply and lay PVC Insulated & sheathed copper conductor single core cable of size 25 sq.mm x single core all as specified and as directed.

Supply, testing and commissioning of 2 X 1.5 sq.mm. solid copper armored cable including shadling/cable gland etc., all as specified and as directed.

Material and labour for ductile iron pipe including specials, class K -7 of size 100 mm dia conforming to IS 8329 including bend ,tee ,socket ,elbow,reducer etc including jointing and jointing material all as specified and as directed.

Supply and fix Dish washer, Quick wash, delay start & error display features 14 place setting, Auto restart feature, refill indicator Quiet, efficient & reliable inverter direct drive Turbo Cycle to clean hard soiled dishes, child lock feature Gliding rail & ball bearing wheel provides an effortless glide Quad Wash ensures cleaning from every angle Sparkling dishes & less water spots with True Stream Easy loading & maximum flexibility with Easy Rack Plus complete all as specified and as directed. MAKES: Bosch / IFB / Godrej

Supply and fix Chimney 90 cm 1200 Cum/Hr auto clean, cleo 90, filterless, steel/grey colour complete all as specified and as directed. MAKES: IFB / ELICA / FABER / HINDWARE / SUNFLAME / INALSA

Provide PROVISIONAL SUM for provision of Solar Water Heating system of capacityr 5000 LPD (02 Nos) including Solar Panel flat plate collector type, with heat exchanger, Hot Water Tanks, Booster Pumps, Water Pipes, Insulation complete all as specified and as directed.

Hariom Projects Pvt Ltd

K R TRADERS

Som Projects Pvt Ltd

Agarwal Jagdish Construction Company Private Limited

vijay infraprojects pvt ltd

Beejay Associates Contracts Pvt Ltd

SHRE GURMUKHDAS CONTRACTOR PVT. LTD.

Sharda Infratech