Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.0 CrAccepted-Finance | ₹1.0 Cr | L1 | Accepted-Finance As per boq |
| 2 | L2₹1.2 CrAccepted-Finance | ₹1.2 Cr | L2 | Accepted-Finance As per BOQ |
Tender Value
₹1.3 Cr
EMD Value
₹2.6 L
Closing Date
21 Feb 2026, 6:00 pmClosed
Executive Engineer
JKPHC JAMMU
Construction of Building (3000 Sq ft) of PCP Badnote Kathua (C. No. 76)
2026_DGPJK_303240_1
Fresh 76 of PHC JAMMU DIV/2025-26 Dated14-02-2025 ( 2nd Call)
Open Tender
Civil Works
270 days
BADNOTE KATHUA
REFER PQ TERMS AND CONDITIONS
3 documents required · 3 mandatory
₹2,000
Executive Engineer, JKPHC Division Jammu
₹2.6 L
Executive Engineer, JKPHC NARWAL JAMMU
24 Feb 2026
14 Feb 2026
23 Feb 2026
14 Feb 2026
21 Feb 2026
14 Feb 2026
14 Feb 2026 - 17 Feb 2026
18 Feb 2026
Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge All kinds of soil
All kinds of Soil 80%
Ordinary Rock 20%
Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: 50 m Beyond Cutting Edge
All kinds of Soil 80%
Ordinary Rock 20%
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.
Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)
Providing and laying in position cement concrete of specified grade excluding C/o centering and shuttering all work upto plinth level in 1:3:6 (1 cement : 3 course sand : 6 stone agg. using 20mm nominal size) crushed agg. including curing complete including all carriages and cost of materials involved.
Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size).
Reinforced cement concrete work in walls (any thickness) including attached pilasters,buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 5.3.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level and above plinth level Mild steel and medium tensile steel bars including all leads lifts and carriages complete.
Brick work with common burnt clay Modular bricks of class designation 7.5. in foundation and plinth including curing complete in Cement mortar 1:6 ( 1 cement : 6 coarse sand)
Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level.
Half brick masonry with bricks of class designation 75 in foundations and plinth in : Cement mortar 1:4 ( 1 cement: 3 coarse sand) , including all costs and carriages of material complete.
Extra for half Brick masonry in superstructure above plinth level upto floor V level.
Centring and shuttering incl strutting, propping etc and removal of formwork in Foundation
Centring and shuttering incl strutting, propping etc and removal of formwork in coulmn
Centring and shuttering incl strutting, propping etc and removal of formwork in plinth Beams Lintel beams etc.
Centring and shuttering incl strutting, propping etc and removal of formwork infor suspended floors, landing , balconies etc
Centring and shuttering incl strutting, propping etc and removal of formwork for edges of slab
12mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 fine sand) .
15mm Cement plaster on the rough side of single or half brick wall of mix:1:6
6 mm cement plaster to Celings of mix 1:3 including all carriage and cost of material involved
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or dash fasteners shall be paid for seperately) sal wood.
Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm.
Providing and fixing Ist quality ceramic glazed wall tiles of size 300 mm x 450 mm conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.All carriages and cost of material included. (make Kajaria,Johnson or Equivalent).
Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown.Al carriages and cost of material included. (make Kajaria,Johnson or Equivalent).
Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour or shade.(Area of slab over 0.5 sqm)
Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite Work
Providing and fixing glazed shutters for doors/windows/ clerestory windows using 10kg/ sqm 4mm thick float glass panes including ISI marked M S pressed butt hinges bright finished of required size with necessary screws. 30mm thick 2nd class kail wood.
Providing and fixing 30mm thick wire gauze shutters using galvanized M.S wire gauze of average width for aperture 1:4mm with wire of dia 0.63mm for doors, windows and clerestory windows including ISI marked bright finished or / and black enameled M.S butt hinges with necessary screws.( 2nd class Kail wood )
.Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or crossbands and face veneers on both faces of shutters.With ISI marked M.S. pressed butt hinges bright finished of required 30mm size with necessary screws
Providing and fixing M.S. grills, Railing, lockup doors of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete
Providing and fixing Aluminium Sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS 1868 ) tranparent or dyed to required colour or shade with nuts and screws etc. complete.
Providing and fixing Aluminium tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS 1868 ) tranparent or dyed to required colour or shade with nuts and screws etc. complete 300 x 16 mm.
Providing and fixing Aluminium hanging floor door stopper ISI marked anodized (anodic coating not less than grade AC 10 as per IS 1868 ) tranparent or dyed to required colour or shade with nuts and screws etc. complete twin rubber stopper
Providing and fixing Aluminium handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS 1868 ) tranparent or dyed to required colour or shade with nuts and screws etc. complete
Finishing walls with OBD of approved brand and manufacture including primer coat with cement primer( two or more coats )incl cost of material and carriage.
Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)
Applying priming coat With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood).
Applying synthetic enamel paint of approved brand and manufacture on wood work (hard and soft wood).
Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete incl cost of material and carriage complete
Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.
Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931
Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931
Providing and fixing uplasticized PVC connection pipe with brass unions 45 cm length , 15 mm nominal bore
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour:600 mm long towel rail with total length of 645 mm, 78 mm wide and effective height of 88 mm, weighing not less than 190 gms.
Providing and fixing Towel Ring
Providing and fixing Looking Mirror 453 x357
Providing and fixing C.P Cup
Providing and fixing C.P Grating.
Providing and fixing Soap Dish.
Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.
Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required. W.C. pan with ISI marked white solid plastic seat and lid.
Providing and fixing wash basin with padestal ,with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 630 x 450 mm with a 15 mm CP Brass single hole basin mixer.
Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour:
Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour: Flexible pipe 32 mm dia
Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.:Internal work-Exposed on wall
15 mmdia nominal bore
20mm dia nominal bore
Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.:Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall:
15 mmdia nominal bore
20mm dia nominal bore
Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work).
15 mm dia. nominal bore
20 mm dia. nominal bore
PVC Pipe 4"
MANHOLE (1' X 1') with cover
MANHOLE (2' X 2') with cover
Floor Trap 3"x4"
PVC Bend 4"
Ball Valve 20 mm
Union 20 mm
TANK NIPPLE
Structural steel work in built up sections, trusses and framed work,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.Riveted and bolted
Providing corrugated G. S. sheet roofing including vertical/curved surfacefixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gram/m2
Providing and fixing 20mm thick wooden planks ceiling (frame work for base to be paid for separately) with M.S. screw 2nd class kail wood
Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately) :12 mm
Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gram/m2
Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 1.00 mm thick with zinc coating not less than 275 gram/m
Providing and fixing plained eaves boarding2nd class kail wood250x32 mm (nominal size )
Demolishing of old Building (Single Storied ) consisting of Mud Mortar / stone masonary foundation , stone walls in supper structure etc. complete job. Stacking of serviceable material and disposal of unserviceable material (Serviceable material to be handed over to the user department by the concerned contractor failing which the cost of serviceable material shall be deducted from the contractor concerned. Plinth area to be measured for the payment.Disposal of unserviceable material within 3km lead included and shall not be paid saperately.
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S Tube
Random Rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including levelling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) and curing complete at window sills, ceiling level and the like: Cement mortar 1:6 (1 Cement : 6 coarse sand
Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished without floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete50 mm thick with 20mm nominal size stone aggregate.
Carriage of material by mechanical transportation.
Sand average lead 52 Km By M.T +1500 meter Head Load
Stone aggregate upto 40mm and abone Average Lead 52 Km By mechenical means.+1500 meter Head Load
Brick work , Average Lead 152 Km By mechenical means.+1500meter Head Load
Disposal of surplus earth for average lead of 100 m Head Load
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box nd earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including conduit as required. 32mm
Supply and fix LED Bulb 9W,230V Energy Efficient lamp Make : PHILLIPS, SURYA, SYSKA
Supply and Fixing ceiling fan 1200mm sweep with downrod,canopy and connecting up including provision of cable withmulti stranded copper conductor cable of size 0.75 Sqmm fromceiling rose to connector of ceiling fan and connecting up complete all as specified and as directed. Make : Usha / Havells / Crompton Greaves
Supplying and fixing of MCB board with required MCBs and box, including all necessary fittings and fixtures, complete in all respects as per site requirements. The MCB distribution board shall be metallic, IP42/43-rated, double-door, surface/recessed type, suitable for single-phase/three-phase systems, prewired with copper bus bars, neutral and earth links, interconnections, and DIN rail for mounting MCBs. MCBs shall be ISI-marked, modular type, conforming to IS: 8828 (latest edition), with SP/DP/TP/TPN configurations of appropriate ratings (6A, 10A, 16A, 32A, 63A) as per load requirements. The installation shall include all necessary accessories, connectors, lugs, conduit/cable entry fittings, and proper earthing as per IS: 3043. The work shall be carried out as per standard electrical norms, ensuring proper alignment, secure mounting, and safe connections, followed by testing and commissioning to ensure proper functionality.
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required
Wiring for 5-10A socket out lets for computer (Inverter) with 2X2.5 sq. mm FRLS PVC insulated copper conductor (Havell/Polycab/ Fenolex/Anchor/ equivalent as directed by engineer incharge.) single core cable in surface/recessed medium class PVC conduit, alongwith 1 No. 2.5 sq. mm FRLS PVC insulated copper conductor single core cable for earthing etc. as required.including the cost of conduit.
Wiring for light/power plug points (15/16A heating points) with 2x4sq mm FRLS PVC insulated flexible stranded copper conductor wires in recessed or surface medium class PVC conduit along with 1x4 sq. mm FRLS PVC Insulated copper conductor single core cable for earthing, etc. as required. (Havells/Polycab/ Anchor/ Finolex/KEI/RR or equivalent) including the cost of conduit
Supplying and fixing 8 Module GI Box with modular plate & cover infront including providing 15/16 A modular Socket ,15/16 A modular Switch(2nos) & 5/6 A modular sockets(Combo) including connections etc. as reqd.
Supply & Installation of Exhaust Fans With Stylish Plastic Exhaust 250 mm(10") in the existing opening including connections,testing commissioning etc as required
Disposal of unwanted Mulba/ material from the site of work including Cheselling & repairing whereever required
Providing ,installation,testing and Commissioning of 100 watt LED Flood light with connection etc as required
supply and fixing of 5 inch dia Fan Box / concealed box with round sheet cover for covering the base and bottom and dual painted with red oxide
Supply & Installation of Bulk Head Lights including connections,testing commissioning etc as required
Conducting and providing soil investigation/ bearing capacity test and preparation of site plan three sets on A2 size, architectural drawings (three sets on A2 size) design of structure (three sets of A3 size) from reputed architect and structural designer and also vetting of structural drawings from IIT, NIT, GCET or DIQC Before execution of work
Please Enable Macros to View BoQ information
stage.html
html • 0.03 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.95 MB
BOQ_984173.xls
BOQ • 0.39 MB
Download all tender documents and submit your bid