SPECIAL REPAIR TO BLDG NO E4 (COOK HOUSE) PROVN OF 04 NOS TOILET AT MAMDOT HALL AND REPLACEMENT OF WATER LEVEL INDICATOR AT WATER SUPPLY INSTALLATIONS UNDER GE (WEST) FEROZEPUR CANTT

Amount

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegitation including roots near out let of RWP and OHT staging area or specifically ordered by Engineer-in-Charge in writing complete all as specified and directed.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified and directed. Note :- Demolition of mud puska to be cut in average thickness from top surface of roof for creating the slope as directed

M&L 10 mm thick screed bed or bedding layer of mortar in cement mortar 1:4 with water proofing compound @ 3% by weight of cement or as per manufacturer instructions will be on surface to have a smooth surface for laying of water proofing membrane complete all as specified and directed. Note: WPC shall be measured and paid for separately.

M&L applying evenly a tack coat of Industrial Bitumen 85/25 at the rate of 1.2 Kg per sqm including cleaning surfaces complete all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3 mm thick reinforced with polyster non wove fabric (Wt not less than 150 gm/Sqm ) land on primed surface by forced application complete all as specified and directed.

M&L applying two coats of solar reflactive bituminous based aluminium Paint @ 0.1 kg per sqm over APP membrane complete all as specified and directed.

Supply only water proofing compound.

M&L brick tiles 40mm thick laid on mud mortar (mud phuska) and joints grouted flush in cement mortar 1:3 mixed with 5% of crude oil by weight of cement and pointed flush as the work proceeds complete all as specified and directed.

All as per Srl item No 8 here-in-before but using old brick tiles retieved from dismantling under item No 1 here-in-before including cleaning and removal of mortar from tiles.

M&L Cover fillet in Plain Cement concrete 1:2:4, type B-0 (using 12.5mm graded stone aggregate) min radius of 75mm thick as in roof and parapet wall junction , roof benching, kerbs, mud stop, coping, rounded or chamfered on edges, incl necessary sloping on roof including form work complete all as specified and directed.

Dismantling of floor hearth and wall tilling incl mortar bedding removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Non - skid Ceramic tiles coloured 7 to 8 mm thick (square/ rectangular),primium quality area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and incl screed bedding 15mm thick in cement mortar 1:6 complete all as specified and directed.

M&L Non - skid Ceramic tiles coloured 7 to 8 mm thick (square/ rectangular),primium quality on vertical surfaces such as in skirting /dado etc area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L Glazed ceramicdisikelly coloured (colour & shade as approved) tile 450mmx300mm & 7mm thick on vertical surface such as skirting / dados set and jointed in neat cement slurry over & including 10 mm thick rendering in cement mortar 1:4 and pointed in white/ coloured cement with pigment to match the colour of tiles complete all as specified and directed.

M&L cement concrete type B-2, 1:2:4 (using 40mm graded aggregate) as in foundation, filling and mass concrete and all other similar works complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil, clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots, and trees not exceeding 30 cm girth (measured one metre above ground level) and removing rubbish upto a distance of 50 metres outside the periphery of the area complete all as specified and directed.

M&L 75 mm thik Cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in sub floors, sub bases,floors and paving etc. complete all as specified and directed.

M&L hardcore of gauge not exceeding 63mm, deposited spread and leveled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paverblocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L Granite(of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 10 mm thick plaster as in back coat cement mortar 1:4 complete including moulding at corners and polishing type complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

Demolition of un-reinforced cement concrete in any position complete all as specified and directed.

M&L Cement concrete 1:3:6, type C-1 (using 20 mm graded stone aggregate) as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as specified and directed.

M&L 3 mm thick glass dividing stripps, 38 mm width of strip and inserted in position to confirm to design complete all as specified and directed.

Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins,arches, pillars etc complete all as specified and directed.

M&L brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified and directed.

All as per Srl item No 26 here-in-before but using old bricks retrieved from demolition under item 25 here-in-before including cleaning and removal of mortar from old bricks complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified and directed.

All as per item No 28 here-in-before but size exceeding 1.5 Sqm and not exceeding 4 Sqm each.

Taking down Shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each and removing to store complete all as specified and directed.

Resecuring or easing & adjusting, without taking down Shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each complete all as specified and directed.

M&L Pressed steel frames made of 1.25mm thick MS sheet of profile 105mmx60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

M&L Pressed steel frames made of 1.25mm thick MS sheet of profile 125mmx60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

M&L Pressed steel frames made of 1.25mm thick MS sheet of profile 75mmx50mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

M&L Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in filling of steel chowkhats including necessary form work complete all as specified and directed.

M&L Cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in bed block of hold fast, coping, including necessary form work complete all as specified and directed.

M&L Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2004) complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified. Make: Rajshri or equivalent as approved complete all as specified and directed.

S&F 35mm thick, 2nd class hard wood (Hollock), plain framed, paneled shutters, any number of panels, panels shall be of 12mm thick BWR glade veneered particle board medium density, wood particle board with commercial face veneers, size of members as specified in clause 8.24 (a) of MES Schedule Part-I section-8 complete all as specified and directed.

S&F 35 mm thick, 2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified.

M&L Medium density fibre board interior grade 18-20 mm thick solid construction type, fixed in repairs in Kitchen cabinets/ CBs doors shutters/ shelves ( horizontal or vertical of any type) on timber frame work /GI Flats orners with screws /nails complete all as specified and directed.

M&L 0.90 mm thick Decorative laminate type -1, both sides of boards surface finish, (colour and pattern as approved) fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F Factory made box type steel window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle single composite unit with glazed and gauged shutter both dovetailed or welded and mild steel 8mm square bar grill welded to frame with one shop coat of zinc chromate primer complete all as specified and shown on drawing No. CEJZ/TD-1019/08 & CEJZ/TD-1020/08 complete all as specified and directed.

S&F Factory made box type steel ventilator side/top hung with glazing bars or dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on drawing No. CEJZ/TD-1019/08 & CEJZ/TD-1020/08 complete all as specified and directed.

M&L preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide priming complete all as specified and directed.

M&L preparation of old steel surfaces of any description, over 10 cm width or girth and applying one coat of synthetic enamel paint over a coat of redoxide priming complete all as specified and directed.

M&L applying two coats of synthetic enamel paint on wooden surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surface & applying one coat of pink primer complete all as specified and directed.

M&L applying one coat of synthetic enamel paint on wooden surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of old painted surface complete all as specified and directed.

S&F continuous (Piano) hinges MS bright finish or Electro galvanized 25 mm wide flaps (when open) including welding to existing frame complete all as specified and directed.

M&L 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares not exceeding 0.50 Sqm complete all as specified and directed.

M&L galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples as in repair complete all as specified and directed.

M&L aluminium anodised tower bolts 150 mm long and fixed with steel screws complete all as specified and directed.

M&L butt hinges, 75 mm long extruded aluminium alloy with galvanised steel hing pins, anodised and fixed, type C-21 complete all as specified and directed.

M&L aluminium door handle, cast type, anodised 150 mm long and fixed with steel screws complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt 300mm length,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 300mm Mild steel helical door spring including roller and roller plate complete all as specified and directed.

S&F 200mm long aluminium, anodised barrel tower bolts of extruded section, complete all as specified and directed.

S&F Mild steel butt hinges 125 mm long medium weight cold rolled with screwed with steel screw or welded to steel frame and fixed with steel screws complete all as specified and directed.

S&F 75mm size, aluminium (cast type) anodized, handle and fixed with screws complete all as specified and directed.

S&F Hasp and staple of aluminium anodized, safety type, 100mm long, fixed with screws complete all as specified and directed.

S&F in repair 20 mm dia curtion rod powder coated fixed with fancy type chromium plated with bracket complete all as specified and directed.

S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging; also fastening & fixing complete GDE Fe410-0 or Fe 310-O complete all as specified and directed.

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etccomplete all as specified and directed.

M&L rendering 15mm thick in cement mortar 1:4 on any face of brick walls or concrete surfaces, finished even and fair without using extra cementcomplete all as specified and directed.

M&L rendering 10mm thick in cement mortar 1:6 on any face of brick walls or concrete surfaces, finished even and fair without using extra cement complete all as specified and directed.

M&L rendering 5 mm thick cement plaster on ceiling surfaces in cement mortar 1:3 finished fair and even without using extra cement complete all as specified and directed.

M&L preparation of new plastered surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L complete removal of existing treatment over wall and applying two coats of distemper oil emulsion over 1mm thick wall care putty complete all as specified and directed.

M&L preparing newly plastered surfaces of wall and applying 2 coats of distemper oil emulsion over 1mm thick wall care putty complete all as directed of any shade on walls surfaces complete all as specified and directed.

M&L preparation of old treated plastered surfaces including complete removal of existing treatment and applying two coats of cement base paint complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls etc., and applying three coats of white washcomplete all as specified and directed.

M&L preparation of old plastered surfaces of walls & applying one coat coat of white wash complete all as specified and directed.

M&L white wash in three coats on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M&L white wash in one coat on old plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation,complete all as specified and directed.

Taking up or down existing steel water tubing, 20mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed.

S&F galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F galvanised iron steel water tubing, 20mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.

Fixing only old 15 mm steel tubing and including cleaning in position (walls, ceiling and floor etc complete all as specified and directed. Notes:- (i) 15mm dia bore serviceable pipes obtained from dismantling (taking up or down) shall be reused. (ii) Cleaning of pipes and the cost of any new fittings if, required at site shall be deemed to be included in the quoted rate.

Fixing only old 20 mm steel tubing and including cleaning in position (walls, ceiling and floor etc complete all as specified and directed. Notes:- (i) 20mm dia bore serviceable pipes obtained from dismantling (taking up or down) shall be reused. (ii) Cleaning of pipes and the cost of any new fittings if, required at site shall be deemed to be included in the quoted rate.

S&F in repair 1000 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I complete all as specified and directed.

S&F chromium plated fancy type 1-way angle cock with flange suitable for 15mm bore pipe, ccomplete all as specified and directed.

S&F chromium plated bib tap for iron pipe of 15mm bore fancy type with crutch or butterfly handle, screwed down high pressure complete all as specified and directed.

S&F in repairs brass chromium plated long body bib tap for iron pipe of 15mm bore fancy type with crutch or butterfly handle, screwed down high pressure complete all as specified and directed.

S&F Low density polythene pipe (LDPE) of pressure rating 6 Kg per Sqcm, 450mm long, heavy duty with two sets of brass nuts & washers (one at each end)etc suitable for 15mm bore of pipe as in repair complete all as specified and directed.

S&F 125mm dia PTMT grating fixed over trap with cement complete all as specified and directed.

S&F Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed to walls with steel screws and wooden/rawl plugs as in repairs complete all as specified and directed.

S&F piller taps, chromium plated, screwed down, high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts, screwed for 15mm bore of iron pipe and fixed complete all as specified and directed.

S&F Soap dish of CP fixed to wall with steel screws and PVC rawl plug complete all as specified and directed.

S&F Vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing complete all as specified.

S&F in repair sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and waste coupling and pipe including bedding in cement morter to dwarft wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410 mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore dia of outlet of pipe complete all as specified and directed.

Excavation in post holes (or similar holes) each not exceeding 0.5 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layer not exceeding 25cm hard and dense soil complete all as specified and directed.

M&L Roof trusses (framed), trussed, purlins, crame gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections), including distance pieces, cleats etc complete all as specified and directed.

M&L Pre painted galvatume aluminum zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F powder coating on any colour (Thickness or powder coating not less than 50 micron) Aluminium anodised door shutters, aluminium section weight 0.55kg/m including necessary joining clwats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc.complete all as specified and directed.

S&F powder coating on any colour ( Thickness or powder coating not less than 50 micron) Aluminium anodised window and ventilator shutters, fixed type without sash bar, aluminium section weight 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1no.), hinges type B-21 100mm long (2 no) suitable handle (1no.) complete all as specified and directed.

M&L 5.5 mm thick sheet glass, ordinary quality and glazing with aluminium beads and rubber gaskit in square exceeding 0.5 sqm in each pane frosted on one side complete all as specified and directed.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and directed.

S&F in repair 5 mm thick coloured of any selecetd design hollow PVC wall cladding strips interlocked to each other fitted to wall including PVC 'U' shapes at top/ bottom and PVC angles at windows/door openings all as per manufacturer’s fixing instructions complete all as specified and directed.

Demolition of ceiling boards of any description, and any thickness including cover fillets and frame work complete all as specified and directed.

M&L GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and directed.

M&L fancy designed 6 mm thick exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grid (frame work for ceiling shall be measured and paid separately) fixed to GI frame work in ceiling and all other similar works complete all as specified and directed.

S&F in repair push tap 15 mm bore any colour of PTMT suitable for urinals screwed for iron pipe and fixed (minimum weight 15mm-47 gms) complete all as specified and directed.

Dismantling asbestos cement/PVC pipe including clamps complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F in repair 110 mm bore PVC (SWR) bends ad provided with access door complete all as specified and as directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F PVC (SWR) bends any radius 75mm dia complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc of cess pits, soakwells & cable/pipe laying etc in any type of soil complete all as specified and directed.

Excavating in trenches exceeding 1.5m wide and not exceeding 3.0m deep and getting out for foundation of cess pits, soakwells & cable/pipe laying etc in any type soil complete all as specified and directed.

M&L plain cement concrete 1:4:8, type D2 (using 40 mm graded aggregate) as in foundation, filling & mass concrete complete all as specified and directed.

M&L RCC M-25 Design mix using 20 mm graded aggregate for foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, and mass concrete etc complete all as specified and directed.

M&L Form work to sides of concrete foundations, footings, bases of columns, raft and raft eams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter for flat rough finished surfaces of concrete complete all as specified and directed.

M&L RCC M-25 Design Mix using 20 mm graded stone aggregate for Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L Formwork to sides of pillars, posts, struts, piers, columns and stanchions for Square, Circular rectangular on plan or polygonal flat rough finished surfaces of concrete complete all as specified and directed.

M&L RCC M-25 design mix using 20 mm gradded stone aggregate for beams, cantilevers & lintel beams etc complete all as specified and directed.

M&L Formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M&L RCC Design mix M-25 in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed.

M&L Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exceeding 10cm but not exceeding 20cm wide complete all as specified and directed.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L RCC Design mix M-25using 20mm grade aggrigates in beams in chajjas complete all as specified and directed.

M&L Formwork to chullah hoods, chajjas, troughs and similar items in cluding edges complete all as specified and directed.

S&F MS TMT bars 10mm dia and over cut to length, bent to shape required incl cranking, bending, spirally for hooking for column, hooking ends and binding with MS wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to FS-410 complete all as specified and directed.

S&F MS TMT bars 6 to 8mm dia and over cut to length, bent to shape required incl cranking, bending, spirally for hooking for column, hooking ends and binding with MS wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to FS-410 complete all as specified and directed.

M&L Brickwork with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M&L Brickwork with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M&L Rendering 15 mm thick in cement mortar 1: 6 on fair faces of brick masonry surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L two coats of cement based paint on external wall surfaces over a coat of alkali resistent primer incl preparation newly plastered surface complete all as specified and directed.

M&L two coats of oil bound distemper on internal wall surfaces over a coat of primer incl preparation newly plastered surface and 1mm thick wall are putty complete.

M&L two coats of oil bound distemper on ceiling incl preparation newly plastered surface and chalk whiting complete all as specified and directed.

M&L Moorum/red bajri filling in floors or paving, laid in layers not exceeding 15 cm thick, spread, leveled and rammed including watering complete all as specified and directed.

M&L hard core filling under floor, breaking stone or boulder exceeding 63mm and not exceeding 100mm gauge of sand stone complete all as specified and directed.

M&L Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M&L Non-skid Coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 75mm thick PCC 1:4:8, type D2 (using 40 mm graded crushed stone aggregate) and including 25mm thick PCC 1:2:4, type B1 (using 20 mm graded crushed stone aggregate) as in sub base, and including 15mm screed in cement mortar 1:4 of floor complete complete all as specified and directed.

M&L Rendering 10mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces of roof complete all as specified and directed.

Returning, filling in soils, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6, type C-2 (using 20mm graded stone aggregate) as in plinth protection, shall be laid in 1:20 slope. The concrete shall be laid at a stretch not exceeding 3-meter in length. Joint gap between the adjoining slab, at corners and at junctions of wall shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen of grade 85/25 garde mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3-meter interval at corner and junction walls complete all as specified and directed.

M&L Figured glass 4mm thick pin head type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F Solid PVC door frame single side prelam of size 50mmx47mm made out of 5mm single side prelam pvc sheet reinforced with ms square tube suppling and fixing in opening as per specification & drawing.

S&F Factory made solid panel PVC door shutter 30mm thick (Styles) consisting of frame made out of MS tubes for top and bottom rails. MS frames shall be covered with heat moulded plain coloured PVC,C, channel having PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and both side prelam PVC sheets top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Stiles and rails feathered at edges. Panelling of both side prelam PVC sheet to be fitted in the MS frame with 3 Nos stainless steel hinge 100 mm size, welded/sealed to the stiles rails with suitable PVC sheet beading and jointed together with solvent cement. S&F in the frame as per manufacturer's instructions complete all as specified and directed.

S&F PTMT butt hinges, 100 mm long and fixed with steel screws complete all as specified and directed.

S&F PTMT tower bolts, 150 mm long and fixed with steel screws ccomplete all as specified and directed.

S&F PTMT door handle, 150 mm long and fixed with steel screws complete all as specified and directed.

S&F water closet, make-Jaquar Single Piece WC S-Trap LYS-WHT-38851S220UFSMN one piece water closet (Size 365mmx655mmx765mm) including screwed down for pipe and fixed complete all as specified and directed.

S&F wash hand basin, make -Jaguar under Counter Basin With Fixing Accessories, Size: 600mmx450mmx170 mm, Shape: Rectangular including PTMT waste fittings & pipe, 32mm bore size and angle iron brackets and fixed and making good disturbed surfaces to match with the existing complete all as specified and directed.

S&F bathroom mirror, make-Koheler, Essential polished chrome colour, size 560 mm x 865 mm rectangular framed mirror K-26052IN-CPL, complete all as specified and directed.

S&F urinal Make CERA, Cat No. : S4010102 Urinal with integrated EFS 320mm x 300mm x 525 mm complete all as specified and directed.

S&F ladies urinal Make CERA, Cat No. : S4040101 Squatting Urinal 470mm x 360mm x 100 mm complete all as specified and directed.

S&F partition for urinal Make CERA, Cat No. : S4090101 Division Plate 90mm x 320mm x 720 mm complete all as specified.

S&F brass CP mixer 15mm bore for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F rotational moulded synthetic (HDPE), water storage tank 1000 litre capacity (cylinderical vertical with closed top,) hoisted & fixed in position all as specified in SSR Part-I complete all as specified and directed.

S&F Chromium plated tubular towel rail 20mm dia D type 60 cm long between flanges.

S&F Mild steel work as in rungs, handles and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L concrete bed to drain pipes of 150mm bore in PCC 1:3:6, type C2 (using 40mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L reinforced concrete pipes 150mm dia, NP-3 laid and jointed complete with collars complete all as specified and directed.

M&L cutting into existing manholes/ crossings of walls etc for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required for 150mm dia pipe complete all as specified and directed.

M&L cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in surface channels and drains etc complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc.as in manhole pipe line portion only complete all as specified

M&L Plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in bed blocks, coping,benching and similar work including necessary form work complete.

M&L providing reinforced cement cocrete 1:2:4, type B-1 (using 20mm graded stone aggregates )as in cover slab (for manhole) and setting in cement mortar 1:4 including necessary form work complete all as specified and directed.

M&L mild steel galvanized steel tubing 15 mm bore (concealed) with screwed socket joints, medium grade, together with all fittings (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.) and fixed complete to walls and ceiling with clips, wall hooks, wooden plugs or laid in floors including, screwing and waste and for forged bends on piping as required complete all as specified and directed.

S&F 15 mm bore Unplasticiscd PVC pipes of pressure rating 10 kgf/cm2 laid in trenches complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F Mild steel galvanized steel tubing 20 mm bore (concealed) with screwed socket joints, medium grade, together with all fittings (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.) and fixed complete to walls and ceiling with clips, wall hooks, wooden plugs or laid in floors including, screwing and waste and for forged bends on piping as required complete all as specified and directed.

S&F stop valves/Angle valves, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore and fix complete all as specified and directed.

S&F Soap dish, vitreous China white, approximate chromium plated brass screws complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F 20 mm dia bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 110 mm dia bore PVC (SWR) pipes single socketed, in any length with rubber ring joinets, laid in trenches or in floor complete all as specified and directed.

S&F 110 mm dia bore PVC (SWR) bends any radius with oval acess door complete all as specified and directed.

S&F PVC (SWR) 'P' trap 125/110 mm including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) gully trap, 125/110 mm dia, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 75 mm dia bore PVC (SWR) pipes single shocketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed.

S&F 75 mm dia bore PVC (SWR) pipes single socketed, in any length with rubber ring joinets fixed to walls complete all as specified and directed.

M&L 25 mm granite as in plateform in mortar 1:4 including pointing in white cement complete all as specified and directed.

M&L 100 mm thick Cement concrete(1:4:8, type D-2 using 40mm graded stone aggregate as in sub floors, sub bases, floors and paving etc complete all as specified and directed.

M&L providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Taking down carefully copper /aluminium point wiring (light, fan , socket or power ) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L Point wiring complete with 1100 volts grade PVC insulated unsheathed FRLS cable of copper conductor, multi stranded of size 1.5 sqmm, single core, in and including rigid non-metallic PVC conealed conduit, with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 sqmm unsheated stranded copper conductor with green PVC insulation connected to common earth dolly complete all as specified and directed for the followings :- (a) One light/fan/Bell Point controlled by one single pole one way switch.

(b) One socket outlet on the same board controlled by one single pole one way switch

(c) One 5 amps socket outlet independent controlled by one single pole 5 Amp switch.

All as per Srl Item No 187 here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sq mm PVC insulated copper conductor and 2.5 Sqmm copper conductor for continuous earthing complete all as specified and directed.

Supply & Fixing Switch piano flush type single pole one way 5/6 Amp complete all as specified and directed.

Supply & Fixing Switch piano flush type 15 amps, single pole one way duly ISI marked complete all as specified and directed.

Supply & fixing Socket outlet 2 in one , 5/6 Amps flush type ISI marked complete all as specified and directed.

Supply & Fixing Socket outlet, 2 in one 6 pin 5 and 15 Amps piano flush type ISI marked complete all as specified and directed.

Supply & Fixing ceiling rose, PVC/Polycarbonate, isolated 65mmx50mm, three terminals complete all as specified and directed.

Supply & Fixing Lamp holder PVC/Polycarbonate,isolated with back plate suitable for batten fittings including 10W LED Bulb complete all as specified and directed.

S&F LED tube light fitting 1X18 W decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Makes:- . Cat Part No LHEXBLP7UN1W018 of make "Havells" or techno-commercially equivalent in approved makes.

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series TPN DBs (Vertical type)fitted with ABS frame and 415 volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed.

S&F MCCB 100 Amps, 415 volts, 16 KA, 4 Pole complete all as specified and directed.

S&F sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 8 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed.

S&F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all specified and directed.

Supply and fixing SPN 32 AMP rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all specified and directed.

S&F Sheet Metal Enclosures with Socket plug top and MCBs Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 20 Amp complete all as specified and directed.

M&L Sub main wiring with two single core PVC insulated FRLS cable with Copper conductor unsheathed cable of size 2x6 Sqmm drawn through in and including PVC Concealed with 1x6 sqmm PVC insulated copper conductor single core for continuous earthing complete including PVC conduit 25 mm dia complete all as specified and directed. Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0 Sqmm and one run of 6.0 Sqmm PVC insulated copper conductor single core,one run of PVC conduit shall be measured as single run)

Supply, laying, commissioning and testing cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 4 core complete all as specified and directed.

M&L sand filling under floors, foundation or cable protection including spreading leveling in layer not exceeding 25cm thick complete all as specified and directed.

M&L bricks common brunt clay building bricks, sub class 'B' designation 75 laid dry width wise across the line of cable in trenches for protection of cable complete all as specified and directed.

S&F Mild steel galvanised iron pipe light grade (ISI marked) 40mm bore for passing of earth lead laid in trenches fixed to walls laid under floors, roads including all fittings i.e MS clamps nuts & bolts etc complete all as specified and directed.

S&F Modular Switch one way 6 A, 1 module complete all as per specified and directed. Makes:- - Precision/Anchor/Havells/Legrand

S&F Modular Switch one way 16 A, 1 module complete all as per specified and directed. Makes: - Precision/Anchor/Havells/Legrand

S&F Modular Socket,6A - 2/3 pin combined 2 module complete all as per specified and directed. Makes: - Precision/Anchor/Havells/Legrand

S&F Modular Socket,6A16A - 2/3 pin combined 2 module complete all asper specified and directed. Makes: - Precision/Anchor/Havells/Legrand

S&F Modular white cover plate 2 module complete all as per specified & directed. Makes:- Precision/Anchor/Havells/Legrand

S&F Modular white cover plate 6 module complete all as per specified &directed. Makes : Precision/Anchor/Havells/Legrand

S&F Modular white cover plate 8 module complete all as per specified &directed. Makes : Precision/Anchor/Havells/Legrand

S&F modular metal flush box 1/2 module complete all as per specified & directed. Makes:- Precision/Anchor/Havells/Legrand

S&F modular metal flush box 6 module complete all as per specified & directed. Makes:- Precision/Anchor/Havells/Legrand

S&F modular metal flush box 8 module complete all as per specified & directed. Make:- Precision/Anchor/Havells/Legrand

S&F exhaust fan made of strudy Engineering plastic complete with louvers shutter, voltage 230V,50Hz,RPM 1200, copper winding of sweep 300mm complete all as specified and directed.

S&F LED tube Mirror light 7 Watt 2ft adjustable type energy saving curve type complete all as specified and directed.

S&F sheet metal enclouser SPN DB's 12 way double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series, 240 volts 200 Amps rated enameled bus bar 3 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed.

Supply, laying, commissioning and testing cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 Sqmm 2 Core complete all specified and directed.

M&L Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm & 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009) complete all specified and directed.

S&F galvanised iron steel tubing 25 mm (1") bore ISI marked medium grade with all fittings (ISI marked) duly laid in trenches complete all specified and directed.

S&F Galvanised iron steel tubing 20 mm (3/4") bore ISI marked medium grade with all fittings (ISI marked) duly laid in trenches complete all specified and directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of size 25 mm dia and fixed complete all as specified and directed.

Cutting existing CI/GI pipe 40/50/80/100 mm bore including run lead joints of suitable size with necessary fittings complete all specified and directed.

Supply, Installation,Testing and Commissioning of Ultrasonic Level Transmitter at Sump for measurement of level with following specification:- Range : 0-8 meters Accuracy : 0.5 % minimum Supply Voltage : 24V DC Output : 4-20 mA , 0-10V DC Makes: Nivelco / Siemens / Banner

Supply, Installation Testing & Commissioning of Outdoor type having Canopy and Double Door for weather protection, PLC ( Programmable Logic Controller) based Automation, Protection Panel suitable for control and monitoring of 01 Nos. Ultrasonic Sensor. The panel should be of minimum size 600(H) X 600(W) X 250(D) mm fabricated from 3.15 mm CRCA Sheet. The Panel shall be comprised the following functions & items:- (i) Water Level Sensing & Display (ii) 01 No. PLC with following specifications:- (MAKE:- SCHNEIDER/SIEMENS/ABB/PHOENIX CONTACT) (a). Non isolated RS 485 communication port or Ethernet communication port. (b). Suitable No. of digital / analog input and outputs. (c). Programming software based on IEC to facilitate building of custom build function blocks. (iii) 01 no. HMI - 7" Graphical Touch screen display (Make: SCHNEIDER / SIEMENS/ ABB/ PHOENIX CONTACT) (a). Should have 01 No. RS 485 and 01 No. USB programming port. (b). Should have USB downloading port. (c). Support external data storage on a USB memory stick for storing production data and backing up applications (iv) 01 No. SMPS of 1.5A rating as suitable according to panel design. (Make: SCHNEIDER / OMRON / PHOENIX CONTACT) (v) MCB rating 6-10A. (Make:- Legrand/ Schneider/ABB) (vi) Indicator lamp :- As per requirement (Make:- Schneider/ ESBEE/ABB) CRCA Enclosure:- Make (UNIVERSAL SWITCH GEAR CONTROL / HOFFMAN / ADLEC / TRICOLITE ) Make of the PLC based panel:- (Universal Switch Gear Control or equivalent in ABB Automation/Tricolite/GE Automation)

Supply and fixing Unplasticiscd PVC pipes of pressure rating 10 kgf/cm2 laid in trenches fixing on wall/ laid in trenches for drawing 4 core screened/ shielded communication cable with min 20mm bore and saddles etc complete all as specified and directed. Makes:- Havells/ Polycab/ Belden

Supply and fixing 2 Core 1.5 sq. mm PVC sheathed PVC insulated copper armoured cable complete all as specified and directed. Makes: Havells/Polycab/Gloster

Supply and fixing 4 Core 1.5sq.mm. PVC sheathed PVC insulated copper armoured cable complete all as specified and directed. Makes: Havells/Polycab/Gloster

RAKESH KUMAR SATISH KUMAR (BID ID -3462534)