CA NO GE/AFJ-20/2020-21 REPAIR TO ROOF , FALSE CEILING, FLOORING, REPAIR TO HANGAR DOOR, ATT, JOINERIES IN TECH AREA AND KALUCHAK AREA UNDER GE AIR FORCE JAMMU

Amount

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-in-charge.

Prepainted colored trapezoidal profiled Galvalume/ Zincalume coated steel sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy mettalic coating 550 MPA yield stress as per AS-1397), as in roof covering/cladding to wall fixed with self tapping screws colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling/self-tapping fastener (12-14 x 55 with EPDM seals) complete all as specified and directed by Engr-in-Charge. (Height of roof upto 10 metres) Make : Tata Blue Scope Steel Ltd/JSW Steel Ltd/CRIL

Prepainted colored plain Galvalume/ Zincalume coated steel sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy mettalic coating 550 MPA yield stress as per AS-1397), as in roof covering/cladding to wall fixed with self tapping screws colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling/self-tapping fastener (12-14 x 55 with EPDM seals) complete all as specified and directed by Engr-in-Charge. (Height of roof upto 10 metres). Make : Tata Blue Scope Steel Ltd/JSW Steel Ltd/CRIL

Dismantling wrought iron or mild steel work in posts, struts, including doors, gates but excluding framed truss, etc. or of any description not otherwise provided for complete all as specified and directed by Engr-in-charge.

Dismantling framed trusses of span not exceeding 10 metres complete all as specified and all as directed by Engineer-in-charge.

Structural steel rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed by Engineer-in Charge.

Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165,complete all as specified and as directed by Engineer-in-charge.

Structural steel rolled mild steel work as in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed by Engineer-in Charge.

Dismantling wall and ceiling boards (fibre pulp, insulation etc) or insulation boards / slabs / blankets, any thickness, including cover fillets, complete all as specified and as directed by Engineer-in-charge.

8mm thick PVC laminated Gypsum ceiling board/tiles of size 595 x 595mm, fixed in ceiling with screws to and including frame work of GI channel powder coated complete all as specified and directed by Engineer-in-Charge.

S&F for Hangers 6 mm dia GI ( up to 1200 mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 X 3 mm size 60 mm long drawing complete all as specified and as directed.

M&L for complete removal of existing roof treatment and picking, swiping clean and washing down with wire brushing and cleaning top surface of roof tarraving or cement concrete, including flashings and junction of parapets and usr to neat slurry complete removing debris and rubbish from site including rendering 15mm thick in cement mortar 1:4 mixed with water proofing compound (as per manufacturars instruction) and laying of APP based polymeric membrane minimum weighing 3.6 Kgs/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150 gsm/sqm) laid on primed surface by forced application complete all as specified laid over a coat of bituminous primer @0.3 ltr/sqm and finished with applying bitumen grade 85/25 coat @1.2 Kg/sqm. APP membrane shall be laid by torching with 75mm overlap in longitudnal direction and applying one coat of aluminium as directed. The products of the following firms shall be used for water proofing membrane: - MAKE: (a) "Hyper Plus Standard" (b) "Multi Plus" (c) Bengal Acquaflux-Bengal Bitumen" (d) "Superior Poly Plus S-30"

Supply and fixing in repairs 110mm bore, PVC (SWR) pipes, pressure rating 4 kg/sqcm, single or double socketed, in any length with rubber ring joints, fixed to wall with clamps, (work is to be commenced upto 30metre height) complete all as specified and as directed by Engr-in- Charge. MAKE: SUPREME /ASHIRWAD / FINOLEX / SFMC / ASTRAL

PVC (SWR) bend and shoes any radius, for 110 mm bore pipe, complete all as specified and as directed by Engineer-in-charge. MAKE: SUPREME /ASHIRWAD / FINOLEX / SFMC / ASTRAL

Demolition of Cement Concrete of any description and in any position not otherwise specifically provided for, including removal of demolished materials to a distance and deposited out side of Air Force station where directed at a level not exceeding 1.50 metre above the starting point, complete all as specified and as directed by Engineer-in-charge.

M&L for 75 mm thick plain cement concrete 1:4:8 type D2 (40mm graded crushed stone aggregate) as in sub base of flooring complete all as specified and as directed by Engr-In-Charge.

25 mm thick, Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in sub base for laying floor finishes including finishing the surfaces even and rough without using extra cement, complete all as specified and as directed by Engr-in-Charge.

M&L for 80 mm thick reflective coloured interlocking machine pressed precast concrete interlocking paver block any shape, any colour and rubber finished type confirming to IS 15658-2006, M-40 grade laid and jointed in neat cement slurry with grey cement and pigment laid over 30 mm thick sand cushioning complete all as specified and directed. MAKE: NTC/NITCO/ULTRA /JOHNSON

M&L for 60 mm thick reflective coloured interlocking machine pressed precast concrete interlocking paver block any shape, any colour and rubber finished type confirming to IS 15658-2006, M-35 grade laid and jointed in neat cement slurry with grey cement and pigment laid over 30 mm thick sand cushioning complete all as specified and directed. MAKE: NTC/NITCO/ULTRA /JOHNSON

M&L for 20 mm thick interlocking machine pressed precast concrete interlocking paver block any shape, any colour and rubber finished type confirming to IS 15658-2006, M-35 grade laid and jointed in neat cement slurry with grey cement and pigment, laid over and including 15mm thick screed bed in cment mortar 1:4 complete all as specified and directed. MAKE: NTC/NITCO/ULTRA /JOHNSON

M & L for coloured heavy duty parking tiles 300MM X 300MM X 10 to 12 MM thick, set, jointed & pointed in neat cement slurry in floor with grey cement mixed with colour pigments over 20 mm thick screed bed in 1:6 CM complete all as spd. & directed. MAKE: NTC/NITCO/ULTRA /JOHNSON/AGL/KAJARIA/CERA

Providing, cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregates) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, bed blocks for hold fasts, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed by Engineer-in-Charge.

Providing precast cement concrete Type B1 1:2:4 (20mm graded crushed stone aggregates) as in kerb stones of any section and size, window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling) corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar 1:4 including necessary form work complete with joints to match complete all as specified and as directed by Engineer-in-Charge.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots complete including removal all debries exceeding 50m but not exceeding 100m all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars,drains etc, but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and directed.

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4, complete all as specified and as directed by Engr-in-Charge.

M&L for Brick work with old size bricks, using old serviceable bricks, as retrieved from dismantling of brick work under respective item, after removing mortar from and cleaning bricks; straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar 1:4, complete all as specified and directed by Engr-in-charge.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper in any tint, over a coat of primer over and including one coat of Birla white wall care putty @ 1.20 kg per sqm, complete all as specified and directed by Engr-in-charge. MAKE: NEROLAC PAINTS/JEHNSON & NICHOLSON /BERGER PAINTS/ICI DULUXE/ASIAN PAINTS

Preparation of old previously treated surfaces of walls including complete removal of exisiting treatment and applying two coats of oil bound distemper in any tint, over a coat of primer over and including one coat of Birla white wall care putty @ 1.20 kg per sqm, complete all as specified and directed by Engr-in-charge. MAKE: NEROLAC PAINTS/JEHNSON & NICHOLSON /BERGER PAINTS/ICI DULUXE/ASIAN PAINTS

Preparation of old surfaces of walls by brooming down with steel wire brushes, scrapping down smoke soot moulds moss and efflorescence salts washing, rubbing down and cleaning oil greasy spots etc and apply one coat of white wash to walls complete all as specified and directed by Engr-in-charge.

Preparation of old surfaces of ceiling by brooming down with steel wire brushes, scrapping down smoke soot moulds moss and efflorescence salts washing, rubbing down and cleaning oil greasy spots etc and apply one coat of white wash to ceiling complete all as specified and directed by Engr-in-charge.

Preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Preparation of old decorated surfaces of wood and wood based material of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-charge.

Preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide/zink chrome primer, including removing of zinc coating by using modrant solution before applying red oxide primer complete all as specified and as directed by Engr-in-Charge.

Preparation of old decorated surfaces of steel or iron works of any description exc 10 cm over width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engr-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed by Engineer-in Charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre but not exceeding 4.00 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed by Engineer-in Charge.

Taking down wooden shutter of any dscription n.exc 1.00 Square metre, each (with all fittings) complete all as specified and directed.

Taking down wooden shutter of any dscription exc 1.00 Square metre but n.exc 2.00 Square metre , each (with all fittings) complete all as specified and directed.

Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing, conforming to Fe 410-W (Gde- E- 250) quality-A complete all as directed at site.

Cutting holes in brick walls exceeding half brick but not exceeding one brick built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed by Engr-in-Charge.

S&F for factory made 35mm thick 2nd class hard wood Plain, framed, panelled shutters, with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces.The size of rail and stile as per IS:1003 (Part-I), kiln seasoned and chemically pressure treatedmedium density, wood particle board with commercial face veneers fitted to chowkhat complete all as specified and as directed by Engineer-in-Charge. MAKE: M/S WOOD PRODUCT INDORE M/S GOYAL INDUTRIES CORPORATION 8743 DESH BANDHU GUPTA ROAD NEW DELHI M/S JAIN WOOD INDUSTRIES MURTHAL SONIPAT M/S PIONEER TIMBER PRODUCT CHANDIGARH M/S SHIV JOINERY& FURNITURE INDUSTRIES JAMMU

S&F for factory made 35mm thick 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass/gauge etc divided into squares, with plain , chamfered or rounded, mitred and rebated sash bars, any numbers edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of door shutters as specified in SSR Part-I sec 8 clause 8.20 (a), fixed to chowkhat all as specified and as directed by Engineer-in-Charge. MAKE: M/S WOOD PRODUCT INDORE M/S GOYAL INDUTRIES CORPORATION 8743 DESH BANDHU GUPTA ROAD NEW DELHI M/S JAIN WOOD INDUSTRIES MURTHAL SONIPAT M/S PIONEER TIMBER PRODUCT CHANDIGARH M/S SHIV JOINERY& FURNITURE INDUSTRIES JAMMU

Steel window (box type) factory made with side hung shutters including pintol hinges, with 02 Nos tower bolts of 150 mm size on each shutter, steel handle and stopper of Z section with sash bars dovetailed or welded ready for glass fixing, including all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer, without guard bars/grills complete all as specified and shown in drawing No CEPZ/TD-325/07 dated 04.02.2007 and CEPZ-TD-324/07 dated 04.12.07 MAKE: M/S AGEW STEEL MANUFACTURE PVT LTD AHMEDABAD / M/S SHIV MULARA NARODA AHMEDABAD / GODREJ AND BOYCE MFG MUMBAI / SEN HARVIC MUMBAI / SHIVAM STEEL JAMMU

Description all as per item No 45.00 here in before but without glazing bar but including 10 x 3mm flat iron for fixing wire gauge, dovetailed or welded complete all as specified and as directed.

S&F in repair Galvanised mild steel wire cloth 0.56mm nominal dia wire and average width of aperture 1.18mm and fixed with tinned tacks of galvanised wire staple to steel windows/fixed with wooden beads of 2nd class HW to wooden doors/windows complete all as specified and directed.

Hacking out old broken glass (any thickness size/ quality description) from metal frame including punching or drilling out old glazing pin/spring clips and providing and fixing new one complete all as specified and directed.

S&F for 3.00mm thick sheet plain glass ordinary quality and glazing with oil putty/ wooden beads with nails in square n.exe 0.5 Square metre in each pane etc complete all as specified and directed. MAKE: SAINT GOBAIN/MODI GUARD/ATUL/ASAHI

S&F for 3.00mm thick figured type pin headed glass sheet ordinary quality and glazing with oil putty/ wooden beads with nails in square n.exe 0.5 Square metre in each pane etc complete all as specified and directed. MAKE: SAINT GOBAIN/MODI GUARD/ATUL/ASAHI

S&F in repair 125mm hasp & staple safety type of aluminum with mild steel hinge including bolt to hinge plate and fixed with screw complete all as specified and directed.

S/F for Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. MAKE: SINTEX INDUSTRIES/RAJSHRI PLASTIWOOD LTD/ M/S DURA PLAST EXTRACTION PVT LTD/FENESTA / POLYTUFF

20 to 22mm thick PVC, UV printed shutter one side UV printed designing and back side plain colour printed for cub board boxes or Kitchen cabinet with itself, drawer, shutter and frame full size fitted under cooking platform and other platform including fittings, etc. complete all as specified and as directed. Make: MAKE: SINTEX INDUSTRIES/RAJSHRI PLASTIWOOD LTD/M/S DURA PLAST EXTRACTION PVT LTD / FENESTA/POLYTUFF OR ANY OTHER MAKE AS APPROVED BY E-in-C's BRANCH

S/F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed. MAKE: SINTEX INDUSTRIES/RAJSHRI PLASTIWOOD LTD / M/S DURA PLAST EXTRACTION PVT LTD / FENESTA / POLYTUFF

Butt hinges, medium weight, cold rolled mild steel and fixed with screws to wooden frames or with welding to existing MS frames, 100 mm size, ISI marked, complete all as specified and directed by Engineer-in- Charge.

Continuous (piano) hinges width of flaps 40 mm when opened, mild steel, bright finish or electrogalvanised complete all as specified and as directed.

40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finishedcomplete, fixed in repairs, all as specified and dirceted.

Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed fixed in repairs complete all as specified and dirceted.

S&F for Aluminium alloy, anodised, sliding door bolt, ISI Marked, 250mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F for Aluminum, anodized, barrel tower bolts, ISI Marked, of extruded section 150 mm long, complete all as specified and directed.

Aluminium handles, cast type anodized of size 125 mm, ISI marked, complete all as specified and directed by Engineer-in- Charge.

Galvanised mild steel wire cloth 0.56mm nominal dia wire and average width of aperture 1.18mm and fixed with tinned tacks of galvanised wire staple to steel windows/fixed with wooden beads of 2nd class HW to wooden doors/windows complete all as specified and directed.

Material and labour for Anodized powder coated aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc, complete in all respect as per manufacturer's instruction and including making good disturbed surfaces complete all as specified and directed by Engineer-In-Charge. Make : Hindalco/Indalco/Jindal

Powder coated aluminium window fixed type with three track (min 1.5mm thick) with three shutters made of 18 x 40 x 1.25 mm section (one for wire mesh and two for tinted glass) with rubber gasket beading and locking arrangement etc complete all as specified including 5.5mm thick tinted glass and wire mesh of size 0.56mm dia of wire and 1.40mm aperture including making good distrubed surfaces complete all as specified and directed by Engineer-in-Charge. Make : Hindalco/Indalco/Jindal

Anodized aluminium powder coated window/ventilator side hung type without sash bars, aluminium sections weighting 0.55 Kg/ m (min 1.5mm thick) shutters including 5.5mm tinted glass with rubber gasket beading and locking arragement and wire mesh of size 0.56 mm dia of wire and 1.40mm aperture, jointing cleats, glazing clips, rubber packing, anodised aluminium fittings such as peg stays 150 mm long (1 no), hinges type B21, 100 mm long (2 nos) suitable handle (1 no) etc including making good disturbed surfaces to match with the existing finishes complete all as specified and as directed. Make : Hindalco/Indalco/Jindal

Anodised aluminium powder coated door shutters, fixed type with sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium fittings such as 150 mm long (4 nos) hinges, 200 mm long (2 nos) suitable handle,, 250mm long Aluminium Tower bolt (1 no), 140mm long aluminium door stopper 01 No and anodised alumnium snap beading, screws etc. complete all as specified and as directed. Make : Hindalco/Indalco/Jindal

S&F for 5.50mm thick sheet plain glass ordinary quality and glazing with oil putty/ wooden beads with nails in square exceeding 0.5 Square metre in each pane etc complete all as specified and directed. MAKE: SAINT GOBAIN/MODI GUARD/ATUL/ASAHI

5.50mm thick sheet glass, ordinary quality, (sheet glass ground or obscured or frosted, on one side), glazing with glazing clips not exceeding 0.50 Sqm in each pane, rubber packing anodized aluminium snap beading screw with aluminium frame work complete all as specified and as directed. MAKE: SAINT GOBAIN/MODI GUARD/ATUL/ASAHI

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, fixed in repairs, complete all as specified and dirceted. MAKE: GODREJ/DROMA INDIA/DYANA/EVEREST

Aluminium (extruded section body) door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg, fixed in repairs, complete all as specified and dirceted. MAKE: GODREJ/DROMA INDIA/DYANA/EVEREST

Cement concrete 1:3:6 type C2 using 40mm graded stone crushed aggregate in plinth protection, 75mm thick, finished even and smooth using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete.

Cast iron work grade FG 150, machined, in rollers, pulleys and the like small articles exceeding 10 kg each article, including railing/rollers, suitable to match with railing at ground level for smooth movements of shutter, fixed in repairs, complete all as specfied and directed.

Post construction anti-termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors, complete all as specified and directed by Engineer-in-Charge. NOTE: Anti-termite treatment shall be got done through an proved specialized agency as mentioned below: MAKE (i) M/S Pest control Service, Delhi. (ii) M/S Pest Control, Corporation Delhi. (i) M/s Pest Control Delhi. (ii) M/S Dr Swarop’s Pest Control. (iii) M/S Pesst control & Fumigation Enterprises Delhi.

Post construction anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron, complete all as specified and directed by Engineer-in-Charge. NOTE: Anti-termite treatment shall be got done through an proved specialized agency as mentioned below: MAKE (i) M/S Pest control Service, Delhi. (ii) M/S Pest Control, Corporation Delhi. (i) M/s Pest Control Delhi. (ii) M/S Dr Swarop’s Pest Control. (iii) M/S Pesst control & Fumigation Enterprises Delhi.

Post construction anti-termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same, complete all as specified and directed by Engineer-in-Charge. NOTE: Anti-termite treatment shall be got done through an proved specialized agency as mentioned below: MAKE (i) M/S Pest control Service, Delhi. (ii) M/S Pest Control, Corporation Delhi. (i) M/s Pest Control Delhi. (ii) M/S Dr Swarop’s Pest Control. (iii) M/S Pesst control & Fumigation Enterprises Delhi.

SCHEDULE 'A' PART-II (Schedule of credit) Credit amount of Rs (Refer schedule of credit) for retrieved material mentioned in Sch 'A' Part-II of Tender documents in PDF form will be deducted offline during acceptance of tender of lowest bidder.

Note: (1) The repair has to carried out as and when required basis and accordingly site will be available in piecemeal wise and as directed by Enginer-in-Charge in the Technical area of Air Force station and Kaluchak area

Rakesh Kumar Malia

M/s Sunny Gupta

M/s Mohan lal