Supply of Materials and Erection for Construction of 11 KV and LT line, 33/11 S/S, Installation of New Power T/F, Increasing Capacity of Distribution T/F and Replacement of Damaged Poles etc. under EDC Pratapgarh Distt. Pratapgarh in Deposit Scheme

Supply of Materials for Construction of 33/11 KV S/S (1x5) MVA Derwa and 1x5 to 2x5 Dhakwa, Katra Gulab Singh and Installation of 11 KV VCB at different S/S

Terminal gantry Structure

Main Bus bar complete with structure

33 KV Pin Insulator with G.I. pin

33 KV Line Isolator

33 KV Bus Isolator

Structure for above

33 KV Post Insulator

Structure for above

Lightning Arrester

Structure for above

33/11 KV 5 MVA T/F

90 Lbs Rail Pieces for T/F(44.64Kg)/M

Plinth and Foundation of T/F (5 MVA)

33 KV VCB with Single T/F control Pannel and CT 200/100/ 1A with Structure

Plinth and Foundation of VCB

11 KV Switch gear

11 KV Switch gear 600/300/5A 350 MVA I/C

11 KV Switch gear 200/100/5A 350 MVA O/G

11 KV 3x185 mm2 XLPECable

11 KV 3x120 mm2 XLPECable

11 KV 3x185 mm2 XLPE Cable Jointing Kit O/D & I/D

M.S.Channel 125x65x4000mm for cable stand

11 KV 3x120 mm2 XLPE Cable Jointing Kit O/D & I/D

24 Volt Battery & Battery Charger

Control cables

Control cable 4x2.5 mm2

Control cable 2x2.5 mm2

Earthing of Sub Station

Outdoor equipment (Including earth mat)

Indoor equipment (Including earth mat)

Barbed wire fencing with gate etc.(Switchyard)

D/P of 11 KV Structure on PCC. 8.5 mtr. For feeder

Outdoor & Switchyard & approch road lighting

63 KVA 11/0.4 KV T/F

11 KV fuse set with fixing clamp

11 KV TPMO Switch with fixing clamp

Cost of Accessories for mounting of 63 KVA T/F

L.T.PVC cable 4x25 mm2

Painting of S/S Structure

Sundries of stores

Table Wooden

Chair Wooden

Fire bucket(04no.) with stand

Hand gloves

Nomenclature board of Switch Yard & control room

Rubber Matting

Sub-Station Name Board

ERECTION OF WORK AS PER RESSPO NORMS.

Errection of complete terminal gantry already fabricated and provided by the Contractor in switch yard as per drawing.The work includes mounting and fitting of 33KV Disc Insulator,Disc fitting, Pin, Pin insulator, M.S.Channel and all other accessories provided by the department to complete terminal gantry.Work also includes construction of gantry plinth of size 1.0x0.45x0.45 cum with cement,coarse sand and ballast in ratio 1:3:6 and Plastaring of plinth with cement & sand in ratio 1:4 including digging of Pits & backfilling, All Concreting material like cement, ballast, sand Labour & T&P etc.shall be also provided by the contractor.

Erection of complete bus bar gantry already fabricated and supplied by the Contractor in switch yard as per drawing.Work also includes construction of gantry Plinth of size 1.0x0.45x0.45 cum with cement,coarse sand and ballast in ratio 1:3:6 and Plastaring of plinth with cement & sand in ratio 1:4 including digging of Pits & backfilling,All Concreting material like cement,ballast,sand Labour & T&P etc.shall be provided by the contractor.

Erection of complete structure for 33 KV Isolator in switch yard as per RESPO drawing. Work also includes construction of gantry Plinth of size 1.0x0.45x0.45 cum with cement,coarse sand and ballast in ratio 1:3:6 and Plastaring of plinth with cement & sand in ratio 1:4 including digging of Pits & backfilling,All Concreting material like cement,ballast,sand Labour & T&P etc.shall be provided by the contractor.

Erection of complete structure for 33 KV lightening arrestor in switch yard. as per RESPO drawing. Work includes Erection of 3 Nos.33 KV Lightening arrestor, its fitting and mounting with care. Grouting of structure with L.C, of 1:3:6 construction of plinth size 0.90x0.45x 0.45 cum. plastering the plinth with cement mortar with cement and sand in ratio 1:4. Works includes cost of clamp concrete material, labour T&P and cement, which shall be provided by the contractor.

Erection of complete 33 KV VCB with structure in switchyard and grouting of VCB Structures. C.T. Structure by cement, sand, brick ballast mortar in ratio 1:3:4. Work includes complete fitting of VCB and C.T. on structure carefully with making all connections of control cable for operating the VCB and C.T. Only VCB, C.T., Battery and battery chargar and their structure shall be provided by the Contractor . All other item like cement, concrete material, T&P shall be provided by the contractor. Work also includes installation and commissioning of Battery and Battery charger.

Installation of 33 KV transformer control pannel in the switchgear room and grouting the pannel by rag bolt using cement, sand mortar in ratio 1:3. Work includs fitting of all accessories in all respect with complete connection of control cable with pannel.Grouting material will be provided by the Contractor.

Erection of complete structure for 33 KV post Insulators in Switch yard. Work includes Installation of 3 Nos. 33 KV Post Insulator on each structure complete as per schedule, grouting of Structure with Ist class brick ballast in the ratio of 1:3:6, plastering in the ratio of 1:3 on plinth size 0.90x0.45x0.45 Cum. The work is to be done strictly as per RESPO drawing. All the material like post Insulator cap, Cement, concrete material used for above work will be provided by the Contractor.

Construction of complete T/F plinth size 4.46 x 3.46 x 1.0 Mtr. above the ground level and 0.5 Mtr. deep foundation made as per drawing. Top of plinth is to be L.C. work in the ratio of 1:3:6 fitted with 3 Mtr. long, 90 lbs, 2Nos. rail pieces. Cement mortar is to be used in 1:3 ratio. Cement, concrete material, bricks used in plinth shall be supplied by the contractor. 6” stone grit is to be laid before foundation start for whole plinth. Only Rail pieces shall be supplied by Contractor . Other material shall be provided by the contractor.

Safe shifting and mounting of 33/11 KV 5 MVA T/F on the transformer plinth. This work includes dragging loading, shifting, lifting and complete assembling after placing on the plinth.All special and ordinary T&P is to be arranged by the contractor. Special care is to be taken to avoid tilting of T/f and loss of transformer oil. Any damage in T/F will be chargeable to contractor.

Laying of earth mat through out 33 KV Switchyard area as per RESPO design and drawing provided by the department. The work includes digging of trenches 0.75 Mtr deep as per drawing. Boaring of 33 mm M.S. Round electrodes upto 0.5 Mtr below ground level. Connecting all electrodes with the help of G.I. Strips of size 35x6 mm (Approx. 600 Kg) and 40 mm G.I. pipe with proper welding with high quality electrodes M.S. rod, G..I. Strip & G.I. Pipe shall be provided by the contractor.

Earthing of each Structure erected in the yard with 35x6 mm. G.I. strip in duplicate fully welded at both ends to be connected to the earthmat, necessary G.I. strip shall be provided by the contractor.

Earthing of 11 KV indoor equipments, switch gears as per RESPO Drawing. with G.I. Strip of Size 50x6 mm, provided by which will be the contractor.

Earthing of 33 KV C.T. Structure complete as per schedule with 50x6 mm.G.I. Strip. All earthing material shall be provided by the contractor.

Special earthing of lightening arrestor structure with 6 Nos. additional 40 mm dia 2.5 Mtr. Long G.I. pipe electrodes/rod by digging 3 Mtr. deep pits and connecting it with L.A. through G.I. Strip 35x6 mm welded at both ends. All the material Like G.I. pipe, G.I. strip shall be provided by the contractor.

Special earthing of T/F neutral by boring 2” dia 20 feet long G.I. pipe in the wet earth and connecting it with 35x6 mm. G.I. strip to T/F neutral giving half round turn at the T/F. Two separate earthing to be provided to T/F body by connecting it with earth mat by special earthing arrangement for earthing work. Material Like Strip of size 50x6/35x6 mm and G.I. pipe 2” dia 2.9 mm thick shall be provided by the contractor used in above work.

Laying and stringing of ACSR dog conductor for busbar between busbar gantry as well as terminal gantry. Three phase jumpering from bus to bar L.A, VCB, C.T., Post insulator and 33/11 KV T/F, Terminal Gantry, Isolator etc. properly with jumpering with P.G. Clamp, T. Clamp and Post Insulator clamp, P.G. clamp, T.clamp, A.C.S.R. Dog conductor and any other clamp required for jumpering shall be provided by the contractor.

Painting of All structure and equipment inside the switch yard with two coats of red oxide primer and thereafter two coats of aluminium paint, giving silver white finish, painting is to be done after proper cleaning of the structures. paint, primer, thinner etc. required shall be provided by the contractor himself.

Providing and erection of fire stand as per drawing for fire bucket with M.S. Angle Iron 50x50x6 mm with shed of M.S. sheet to cover the bucket and stand properly. All matrial required for this work like M.S. Angle. 5 Nos fire bucket shall be provided by the contractor.

Installation of 11 KV VCB in the switch gear room, by grouting base channel 100 x 50 x 6 x 1000mm. Fixing of 11 KV switchgears rag bolt, mounting of P.T. on incoming.

11 KV In coming

11 KV O/G VCB

Laying of 11 KV 3 x 70/120/185/300 Sqmm. XLPE power cable by digging 0.75 Mtr. deep trench, putting layer of sand in the bottom, ramming it, laying of cable over it RMT and covering the cable from sides and top by laying bricks, finally covering the same by earth and levelling of the same, all the materials, except cable, will be provided by the contractor. Rates may be quoted per RMT

Construction of cable trenchs for L.T. cable for station T/F in the switchyard as per direction of engineer. trenchs to be 12” wide and 9” deep. work includes digging, of trench, concreting of the foundation in the ratio 1:3:6 R.B. wall 9” wide with cement mortar 1:4 and plastering inside the trench in the ratio 1:3 and sand filling in the trench. All material will be provided by the contractor.

Erection of 4 No. D/pole 11 Mtr long STP pole including fixing of Top channel on the top the pole and cross brasing, with the help of clamp for 11 KV outgoing feeder of 33/11 KV S/S all material required for this work shall be provided by Contractor

Erection of 2 No. D/pole 8.5 Mtr long PCC pole for Substation T/F in switch yard including fixing of top channel cross bracing, S/S base angle, TPMO, fuse set and mounting of 63 KVA T/F on D/P and fitting of all accessories as per RESSPO drawing. all material required for this work Shall be provided by Contractor

Cartage of all above materials will be done by Contractor

Termination of cable boxes of size 3 x 185 Sqmm. for XLPE cable Boxes I/D & O/G will be of Heat Shrink indoor type and outdoor type cable boxes will be provided by the contractor

Termination of cable boxes of size 3 x70/120 Sqmm. for XLPE cable Boxes I/D & O/G will be of Heat Shrink indoor type and outdoor type cable boxes will be provided by the contractor

Laying of 0.4 KV Alm. PVC 4x16mm2 L.T. power cable from sub station T/F to L.T. Distribution Board. Approx Length of cable 100 Mtr. Shall be provided by contractor.

Fabrication and fixing of cable support channel of size 125 x 65 x 6mm. 3.5 Mtr. long and grouting with mortar 1:3:6 ratio in switch yard.All the material , shall be provided by the contractor.

Fabrication and fixing of neutral strip support of T/F made of 65x65x6mm. 3.5 mtr. long and grouting with mortar 1:3:6 ratio in switch yard.All the material such as cement, concrete except strip shall be provided by the contractor.

Laying of following copper control cable form C.T. T/F to transformer control pannel/protection Board. All control cable shall be supplied by the contractor.

33 KV line Derwa

SUPPLY OF MATERIALS

Single PCC Pole 9.0 m long

V-type Cross arm 100x50x6 mm, M.S. Channel (7.9 Kg/M, Total Weight 14.5 Kg) with Holding Clamp

ACSR dog conductor (0.25 KM CKT)

Top channel 125x65mm 3200 mm (10.70 Kg./mtr.) with Clamp

33 KV Disc Insulator Polymer 70 Kn

33 KV Disc fitting 70 Kn

33 KV Pin Insulator Polymer

Complete Stay (GI stay rod 20x1800 mm, stay wire 7/8 SWG 10 kg, stay clamp, bolt, nut & washer) with concret grouting

Earthing of pole by MS earthing rod of 20x2500 mm and 6 SWG earthing wire etc.

MS angle iron 65x65x6mm, 4300 mm long bracing with clamp

Earth wire clamp with bolt & nut

E-bracket for 33 KV

F-bracket for 33 KV

Bolts, Nuts & Washers

Danger Board with Clamp

Barbed Wire

Concreating of Support with Cement, Sand and Briks Bllast ratio 1:4:8 0.45x0.45x1.5 Mtr. Deap Under the ground

ERECTION OF WORK AS PER RESSPO NORMS.

Digging of pits of size 0.45x1.25x 1.50 mtr. for erection of PCC pole 9.00 mtr. long ( S/P,D/P,T/P, F/P)

Erection of single PCC pole of 9 mtr long.

Fabrication and erection of double pole of P.C.C. poles 9 mtr long.

Mounting and fitting of V-type cross arm, 33 KV pin, pin insulator, earth clamp complete in all respect as per drawing of RESPO on single PCC pole 9 mtr long and single S.T. pole 11 mtr long. Cross arm, Pin, Pin insutator, cross arm cramp, Danger board with clamp shall be provided by contactor.

Fabrication, mounting and fitting of top channel, bracing made of m.s. angle, earth clamp, 33 KV pin & pin insulators, disc insulator and disc fitting on P.C.C. . double pole. Top channel bracing M.S. angle, 33 KV pin and pin Insulator. Disc Insulator and disc fitting , Earth clamp, stay clamp, top channel clamp, bracing clamp, danger board etc. shall be provided by contractor.

Grouting of single PCC pole 9 mtr long with cement, sand and brick bllast ratio 1:4:8 size 0.45x 0.45x 1.5 mtr deep under the ground as per drawing No. RES-6.Cement, sand, brick, ballast shall be provided by the contractor.(S/P, D/P, T/P, F/P)

Digging of pits of size 0.60x 0.60x1.2 mtr and grouting the stay rod anchor plates 0.45x 0.45x 0.45 mtr with cement, Ganga sand and brick ballast ratio 1:4:8 as per drawing No. RES-16. Cement, sand, brick, ballast shall be provided by the contractor.

Complete fitting of stay rod and fastening stay wire including fitting of stay clamp, turn buckle, and making ring of stay wire on both ends in seven strands 9” to 12” long. Stay clamp, Turn buckle shall be provided by the contractor.

Earthing of single PCC pole by digging 1.00 mtr deep pit and driving the electrodes of MS earth rod and connecting all the metallic parts of poles with earthing rod by G.I. wire and filling pits with soil after completion of earthing.earth wire/ G.I. wire M.S.rod shall be provided by the Contractor.

Laying of A.C.S.R. Dog conductor with the help of aluminium roller by hanging three nos. on each support in a manner taking sufficient care to ensure safety of A.C.S.R. Dog conductor against rubbing on ground, precaution for safety of crops is also to be taken. The work includes jointing of Conductor by providing jointing sleaves, stringing of conductor upto correct sag and binding of conductor with insulators on each support. All material required for above work shall be provided by Contractor such as jointing sleeve binding wire, armour rod etc.

Loading carriage and unloading of following line materials

P.C.C. 9 Mtr. Long.

33 KV 3x300 Sqmm XLPE Cable

Other items as per requirement for construction of line (Disc, Disc fitting, X-arm. Pin, Pin Insulator, stay rod, earth rod, M.S. rod, G.I wire etc.

Jumpring of 33 KV line on 33 KV Bay using P.G. Clamp dog to dog & dog conductor & binding of jumper and other accessories on terminal gantry at 33/11 KV S/S Malawa and Chamanganj Disst. Prayagraj. Binding wire & P.G. Clamp, Aluminium Lug etc. provided by Contractor.

Increasing capacity of 33/11 KV S/S (2x5) MVA to (5+10) MVA Gadwara Bazar

SUPPLY OF MATERIALS

33 KV Bus Isolator

Structure for Above

33 KV Post Insulator

Lighting Arrester

33/11 KV 10 MVA T/F

33 KV VCB with Single T/F control Pannel and CT 200/100/1A with Structure

Plinth and Foundation of VCB

11 KV Switch gear

11 KV Switch gear 200/100/5A 350 MVA O/G

11 KV 3x300 mm2 XLPECable

11 KV 3x120 mm2 XLPECable

Supply of Material for laying of 11KV Cable Including cost of sand & brick

Supply of 11 KV Jointing Kit (3x300 sqmm) to be mounted with switch gear and T/F

11 kv Cable Jointing kit 120 mm.sq.

M.S.Channel 125x65x4000mm for cable stand

Control cables

Control cable 4x2.5 mm2

Control cable 2x2.5 mm2

Painting of S/S Structure

Hand Gloves

Rubber Matting

ERECTION OF WORK AS PER RESSPO NORMS.

33 Kv VCB with Cantrol Pannel

33 Kv Bus isolator

Structure for isolator

33 Kv Post

11 Kv 3x300 mm2 XLPE cable

11 Kv 3x120 mm2 XLPE cable

11 Kv outgoing switchgear

M.S angle 65x65x6mm (for cable stand & Newtrol earthing)

11 Kv Cable jointing kit 3x300 mm XLPE O/D

11 Kv Cable jointing kit 3x120 mm XLPE O/D

Control cable 2x2.5 mm2

Control cable 4x2.5 mm2

33 Kv VCB Foundation

CT Structure

Red Oxide Paint

Allu. Paint

Repairing of Plinth & Foundation of T/F

Dismentaling of Old 5 MVA T/F

Shifting of old 5 MVA T/F plinth to outside switchyard

Installation of New 10MVA T/F at plinth in S/S

11 KV Line (Appx. 144 Km.) From Various 33/11 KV S/S

SUPPLY OF MATERIALS

Single PCC Pole 8.5 m long

Single STP Pole 11 m long

T/Off M.S. Channel of size (2240x65x6) with clamp

V-type Cross arm 100x50x6 mm, M.S. Channel (7.9 Kg/M, Total Weight 14.5 Kg) with Holding Clamp

ACSR Rabbit conductor (144 KM CKT)

MS Angle 65x65x6 mm, 3.2 mtr long (5.8 kg per mtr) for guarding with Clamp

Top channel 125x65mm 3200 mm (10.70 Kg./mtr.) with Clamp

11 KV Disc Insulator Polymer 45 Kn

11 KV Disc fitting 45 Kn

11 KV Pin Insulator Polymer

Complete Stay (GI stay rod 20x1800 mm, stay wire 7/8 SWG 10 kg, stay clamp, bolt, nut & washer) with concret grouting

Earthing of pole by MS earthing rod of 20x2500 mm and 6 SWG earthing wire etc.

GI wire 6 SWG (5 mm) & 10 SWG (3 mm) for guarding and lacing

MS angle 65x65x6mm, 3200 mm long bracing with clamp

Earth wire clamp with bolt & nut

E-bracket for 11KV

F-bracket for 11 KV

Bolts, Nuts & Washers

Danger Board with Clamp

Barbed Wire

Supply of Material for Concreating and Support with Cement, Sand and Briks Bllast ratio 1:4:8 0.45x0.45x1.5 Mtr. Deap Under the ground

11 KV 3x120/185 sqmm XLPE Cable

11 KV 120 sqmm Jointing kit indoor and outdoor

11 KV 185 sqmm Jointing kit indoor and outdoor

ERECTION OF WORK AS PER RESSPO NORMS.

Digging of pits of size 0.45x1.25x 1/6th of pole lenth for erection of PCC pole 8.5 mtr. long (single pole).

Digging of pits of size 0.45x1.25x 1.75 mtr for erection of STP 11.0 mtr. long (single pole).

Erection of single pole P.C.C.8.5 mtr long

Erection of double pole of PCC 8.5 mtr. long

Erection of single pole STP 11.0 mtr long .

Mounting and fitting of V-type cross arm,11 KV pin, pin insulator, Danger board complte in all respect as per drawing of RESPO on single PCC pole 8.5 mtr long only P.C.C. /11 Mtr. S.T.P. pole & cross arms shall be provided by contracto all other material F-clamp, cross arms clamp, Danger board etc. provided by contractor.

Mounting and fitting of T-off channel ,11 KV pin, pin insulator, disc & disc fitting Danger board complte in all respect as per drawing of RESPO on single PCC pole 8.5 mtr long only P.C.C. /11 Mtr. S.T.P. pole shall be provided by contracto all other material F-clamp, T-off channel, Danger board etc. provided by contractor.

Fabrication, mounting and fitting of top channel, bracing made by m.s. angle,11 KV pin& pin insulator, disc insulator and disc fitting on double pole. top channel bracing M.S. angle, 11 KV. pin and pin Insulator, Disc Insulator and disc fitting shall be provided by contractor, stay clamp, Top channel clamp, Bracing clamp, Danger board,E-clamp , PG clamp etc. provided by contractor.

Digging of pits of size 0.60x 0.60x1.2 mtr grouting the stay rod anchor plates 0.45x 0.45x 0.45 mtr with cement, Jamuna sand and brick ballast ratio 1:4:8 as per drawing No. RES-16, Cement, sand, brick, ballast shall be provided by contractor. grouting the stay rod anchor plates 0.45x 0.45x 0.45 mtr with cement, Jamuna sand and brick ballast ratio 1:4:8 as per drawing No. RES-16, Cement, sand, brick, ballast shall be provided by contractor.

Complete fitting of stay rod and fastening stay wire including fitting of stay clamp, turn buckle, and making ring of stay wire on both ends in seven stands 9” to 12” long. Stay clamp, Turn buckle Stay Clamp shall be provided by contractor.

Earthing of single PCC/ ST pole by digging 1.00 mtr deep pit and driving the electrodes of MS earth road and connecting all the metallic parts of poles with earthing rod by G.I. wire and filling pits with soil after completion of earthing.earth wire/ G.I. wire M.S.rod shall be provided by contractor

Work of road, canals, telephones and H.T.line crossing by providing gurding angles/ channels on supports and fabrication and fitting of guarding net as per drawing No. 48 with G.I. wire No. 8/10SWG. guarding clamp turn buckle shall be provided by contractor only G.I wire garding angle provided by contractor

Laying & stringling of A.C.S.R.Rabbit conductor with the help of aluminium roller by hanging three nos. on each support in a manner taking sufficient care to ensure safety of A.C.S.R. weasel conductor against rubbing on ground precaution for safety of crops is also to be taken. The work includes jointing of Conductor by providing jointing sleaves stringing of conductor upto correct sag and binding of conductor with insulators on each support.The contractor shall provide jointing sleeve,Binding wire.All work to be carried out stricktly as per RESPO Norm.

Jumpring of 11 KV line on D/P using P.G. Clamp weasel to weasel & binding of jumper on Pin insulator, P.G. Clamp provided by the contractor.

Laying of 11 KV XLPE Cable 3x120/185 with G.I. Pipe and Cable Box O/D and I/D

Loading carriage and unloading of all line materials will be done by Contractor

P.C.C. 8.5 Mtr. long.

STP 11 mrt long

ACSR Rabbit Conductor

11 KV 3x120/185 sqmm XLPE Cable

Procured items as per requirement for construction of line.(Disc, Disc fitting , X-arm,Pin,PinInsulator,stay rod,earth rod,M.S.rod,G.I.wire etc.)

Trimming of tree branches Big/small tree branches which is lying on 11 KV feeder allignment of 11 KV Line

Small

CONSTRUCTION OF CONTROL ROOM BUILDING, BOUNDARY WALL , ROAD & OTHER MISC. CIVIL WORK AT 33/11 kV SUBSTATION- DERAWA

Item of works

Clearing jungle including uprooting of rank vegetations,grass, bush, wood, trees and saplings of girth upto 30cm measured at a height of 1.0m above ground level and removal of rubbish upto a distance of 50m outside the periphery of UPPCL area cleared. (CSI No. 4.08)

Excavation in foundation in ordinary soil (Loam Clay or Sand) including lift upto 1.5m and lead upto 30m and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of the foundation work. (CSI No. 4.01)

Concrete with 4cm gauge I class brick ballast, coarse sand and cement in proportion of 12:6:1 in foundations and under floors including supply of all materials, labour and tools and plants etc. required for proper completion. (CSI No.5.01 )

Concrete with 4cm gauge stone ballast, coarse sand (F.M. 1.8 to 2.5) & cement in proportion of 12:6:1 in foundations &under floors including supply of all materials, labour and tools and plants etc. required for proper completion. (CSI No. 5.02)

TMT/Tor steel in plain work such as reinforced concrete or reinforced brick work (when not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage, bend, hooks and authorized overlapping shall be measured. (Steel shall be arranged by the contractor)(CSI No. 9.03)

RCC work with cement approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like grainite, quartzite etc from Dalla, Jhansi or other quarries and approved coarse sand in proportion 1:1.5:3 in raft foundation and footings , excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P. (CSI No. 5.27)

RCC work with cement approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like grainite, quartzite etc from Dalla, Jhansi or other quarries and approved coarse sand in proportion 1:1.5:3 in RCC T beam-slab and column , excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P . (CSI No. 5.29)

First class brick (class-150) work in 1:6 cement and coarse sand (F.M.1.8 to 2.5) mortar in foundation and plinth including supply of all materials, labour & T&P etc. required for proper completion of work. (CSI No. 6.01)

First class brick (class-150) work in 1:4 cement and coarse sand (F.M.1.8 to 2.5)mortar in Superstructure for walls of 1/2 brick (115 mm) thickness including supply of all materials, labour& T&P etc. required for proper completion of work (CSI No. 6.03+6.07+6.09)

Earth filling under floors and/or sub station area including cost of earth when obtained from with in 8 km outside UPPCL area including its roylty and carriage including watering, ramming in 20 cm layers and dressing of earth etc. all complete. (CSI No. 4.10)

Local sand filling in plinth including supply of necessary quantity of local sand from outside the UPPCL premises including watering, dressing etc. Rate to include cost of all materials, labour and T&P etc. required for proper completion of work. (CSI No. 4.05)

Pre-Construction anti-termite treatment, by creating a barrier under and around the columns pits, foundation trenches, under floors, junctions of Walls & floors, around the external perimetre of building, expansion joints, surrounding of pipes and coduits etc. (Plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981))with Aldrine emulsifiable 0.2% concentration or any other approved material such as Heptachlore or chlordance will be used. The consumption of emulsion shall be (i) Foundation and masonary @ 5 Ltrs/Sqm, (ii) Back fills in immediate contact of foundation@ 7.5 Ltrs. / Sqm, (iii) Top surface of Plinth filling @ 5 Ltrs / Sqm, ( iv) Junction of walls & floors @ 7.5 Ltrs / Sqm, (v) Soil along external perimetre of building @ 7.5 Ltrs / Sqm (vi) under apron of the building @ 5 Ltrs. /Sqm. The rates includes cost of all materials, labour, equipments, T&P complete. (CSI No. 17.01)

Cement concrete with 2cm gauge approved hard stone ballast, coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 1:1.5:3. including supply of all materials, labour,side shuttering if required and T&P etc. required for proper completion of work (CSI No. 5.21)

Mild Steel or Iron work in heavy sizes such as trusses built up gates, door frames, record, racks roof work gates etc. wrought to required form including holes rivetting or welding where necessary and also fixing in proper position and alignment including cost of all materials supplied by contractor. (CSI No. 9.01)

First class brick (class-150) work in 1:6 cement and coarse sand (F.M.1.8 to 2.5) mortar in super structure a including supply of all materials, labour & T&P etc. required for proper completion of work. (CSI No. 6.01+6.07+6.08)

Providing and fixing steel glazed window and ventilators of standard rolled Mann or Mahavir steel sections conforming to IS 7452-1974 as per drawing joints metered & welded with 100x14x3.15 mm holdfast embedded in cement concrete block 15x10x10 cm. Size of 1:3:6 proportion I.E. First part of cement 3 part of approved coarse sand & 6 part of graded stone (aggregated 20mm. Nominal size) S/F of glass panes of plain pin headed 4mm. Thick nuts glazing clips and special putty of approved make complete and including a cost of red oxide paint. The fabrication should conform to I.S.1038-1975. (Aluminum beading with rubber packing included). (CSI No. 9.17)

RCC work with cement approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like grainite, quartzite etc from Dalla, Jhansi or other quarries and approved coarse sand in proportion 1:1.5:3 in lintels of doors and windows, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P. (CSI No. 5.23)

Cement concrete with 2cm gauge approved hard stone ballast, coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 4:2:1 including supply of all materials, labour,side shuttering if required and T&P etc. required for proper completion of work. (CSI No. 5.06)

RCC work with cement approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like grainite, quartzite etc from Dalla, Jhansi or other quarries and approved coarse sand in proportion 1:1.5:3 in slab, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P . (CSI No. 5.24)

S/F hexagonal Fan Box with hexagonal side of approx 80mm in length fabricated from 16SWG MS sheet incorporating 10mm dia MS round bar duly bend for supporting fan hanger, duly painted with red oxide and screw arrangement and with wiring conduit laid in the RCC roof before concreting alongwith supply of all material labour T&P etc. required for proper completion of work as per direction of EIC.(NSI)

12 mm thick plaster with cement mortar consisting of one part of cement & three part of coarse sand (1:3), minimum thickness not to be less then 10 mm including supply of all material labour and T&P etc for proper completion of work. (CSI No. 11.06)

6 mm. thick plaster with 1:3 cement & coarse sand including labour, materials & T&P etc. required for proper completion of the work. (CSI No. 11.17)

3 mm thick floating coat of neat cement finish including supply of all materials,labour and T&P etc. required for proper completion of the work.( cement consumtion 0.044 bag/Sq.m.) (CSI No. 11.20)

S/mixing approved water proofing compound (CICO,DR FIXIT etc) in cement mortar in plaster or concrete work in the proportion as recommended by the manufacturer. (CSI No. 11.15)

12 mm thick plaster with cement mortar consisting of one part of cement & four part of coarse sand (1:4), minimum thickness not to be less then 10 mm including supply of all material, labour and T&P etc for proper completion of work. (CSI No. 11.07)

12 mm thick plaster with cement mortar consisting of one part of cement & six part of coarse sand(1:6),minimum thickness not to be less then 10 mm including supply of all material, labour and T&P etc for proper completion of work. (CSI No. 11.09)

Add for extra labour and materials for plaster over rough face of one brick thick wall. (CSI No. 11.12)

Providing (12x15) mm section groove in plaster including all material, labour and T&P etc. required for proper completion of the work. (CSI No. 11.16)

Making drip course (25x12) mm in 1:2 cement and course sand including supply of all materials, labour and T&P etc required for proper completion of work. (CSI No. 11.19)

Providing M.S. Frames work, rack etc for R.C.C. Trench covers and edging with M.S. angles and M.S reinforcement including cutting, bending and welding as per approved drawing. The rate is including cost of all labour, materials etc. as required for proper completion of the work. (CSI No. 9.20)

Fixing of cable trench edging in proper position and alignment including cost of all labour, material and T&Petc. required for proper completion of the work (Labour rate only). (CSI No. 9.30)

Concreting of 40 mm thick RCC trench covers in mild steel frame work with RCC 1:1.5:3 in Cement,Chopan coarse sand (F.M. 1.8 to 2.5) and 2cm gauge graded hard stone ballast with 3mm thick floating coat of neat cement finish on top of cover complete with all labour, materials and placing the same in proper position at required location of cable trench within the substation area. (CSI No. 5.18)

4.0 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and T&P etc, required for proper completion of the work. without base CC (CSI No. 12.04)

Providing and fixing glass strips of 3.15 mm thickness & 40mm depth in joints of floor and skirting at the time of laying floors, flush with floor level including supply of all materials, labour& T&P etc. completion required for proper completion of work. (CSI No. 12.14)

Supply of 80 mm thick I shaped mechanically compressed inter locking cement concrete paver block manufactured by high pressure & controlled vibration machine having plan dimension 200X(160+120 mm) with minimum 5 mm thick toping of O.P.Cement mixed with 25% marble powder. The compressive strength of concrete pavers blocks shall not be less than 30 MPa & 4.5 Kg/No. including cost of all material, labour, T&P etc. required for proper completion of work as directed by Engineer-in-charge but excluding G.S.T. which shall be paid extra as per rules. (CSI No.12.23)

Straight over burnt bricks on edge floor laid dry, joints sand filled, including preparation of base to proper slope and its ramming including supply of all material labour & T&P etc. required for proper completion of the work. (CSI No. 12.09)

Supply and fixing galvanised mosquito proof jali (16x24 gauge) with M.S. flat of 20 x 3 mm. size, on both sides screwed or welded to window or door frame. (CSI No. 9.18)

Providing and laying floor of 8 mm thick vitrified tiles in flooring or skirting of approved brand (Bell, Johnson or equi. make) size of 600x600 mm of approved shade, colour and pattern , laid over base cement mortar 1:4 mix including finishing the joints with white cement mixed with pigment to match the shade of tile including cost of all material, labour and T&P required for proper completion of the work. (CSI No. 12.18)

Supply and Laying 8 mm thick glazed floor tiles of Somany, Johnson or equivalent make, of size 300x300 mm, laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry, jointing and polishing complete, including supply of all materials, labour and T&P etc. completion required for proper completion of the work. (CSI No. 12.11)

Supply and Laying 6 mm thick glazed tiles of size 300x450 mm in skirting / dado laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry, jointing and polishing complete,including supply of all materials, labour and T&P etc. completion required for proper completion of the work. (CSI 12.12)

Supply and filling brick bat in soak pit including all labour,material and T&P etc complete. (for 01 soak pit) (CSI No. 6.23)

First class brick (class-150) laid dry in foundation and plinth as in circular soakpit walls of one brick thickness and 2.0 to 3.0M depth including cutting moulding bricks as required including cost of all materials labour and T&P complete. (CSI No. 6.16)

Providing and fixing 15 mm dia B-class Jindal,JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.01a)

Providing and fixing 20 mm dia B-class Jindal,JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.01b)

Providing and fixing 25 mm dia Jindal, JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes external GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.02C)

Providing and fixing 32 mm dia Jindal, JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes external GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.02d)

Providing & fixing half turn 32mm dia gate valve, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.05d)

Providing & fixing half turn 25mm dia gate valve, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.05c)

P/FBRASS ANGLE VALVE 15 mm dia (400 gsm) ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.16i)

Providing and fixing CP BRASS BIB COCK15 mm dia. HEAVY QUALITY ( 400gm) ( L & K and equi.) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.16a)

Providing and fixing CP BRASS Piller cock HEAVY QUALITY ( L&K or equi. ) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.16j)

Providing and fixing first quality white glazed "Orissa" pattern W.C.Pan Hindustan, Cera make. size 580 mm.(Hindustan,Cera Make) with out "P" trap including supply of all materials,labour and T&P etc.complete. (CSI No. 27.01)

Providing and fixing PVC CONNECTION PIPE, 450X15 with 2 brass units ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.09b)

Providing and fixing in position 32 mm. dia P.V.C. WASTE PIPE FOR WASH BASIN. including supply of all materials,labour and T&P etc.required for proper completion of the work. (CSI No. 27.14)

Providing and fixing 100 mm dia PVC "P" or "S" trap including cement concrete and all materials, labour cartage T&P etc.required for proper completion of the work.(For W.C.) (CSI No. 27.24)

Providing and fixing 10 littres low level PVC flushing cistern, COMPLETE WITH ALL FITTINGS including supply of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 27.12)

Providing and fixing in position 32 mm. dia P.V.C. flush pipe. for W.C. with unions, bends etc. including supply of all materials,labour and T&P etc.required for proper completion of the work. (CSI No. 27.13)

Supply and fixing 100 mm dia PVC Nahani Trap India make of heavy approved quality complete with grating, including supply of all materials,labour and T&P etc. required for proper completion of the work. (CSI No. 27.21b)

Providing and fixing 550X400 mm wash hand basin of white glazed earthern ware first quality I.S.I. marked (Hindustan,Neycer / Cera make) including supply of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 27.08)

Supply and fixing of Syntex or equivalent make water storage tank including all materials, labours, T&P etc required for proper completioon of work. (CSI No. 26.12)

Providing and fixing of 110 mm dia PVC pipe 6 Kg/ Sq.cm for with special such as Tee, bend, socket, elbow etc including supply of all labour,material,T & P etc complete required for proper completion of work. (CSI No. 26.17)

Providing and fixing 600 mm x 450 mm beveled edge mirror of Atul,Kiran makeglass with Indian polish 6.50 mm thick complete with back of 600 mm x 450 mm x 6 mm hard board sheet fixed to wooden cieats with C.P. brass screws and washers including supply of all materials, labour and T&P etc.required for proper completion of the work. (CSI No. 27.15)

Applying Birla or equivalent putty on new interior or exterior surface over one coat of water based cement primer of ICI or equivalent brand for smoothening and levelling of the surface as per requirement and direction of Engineer I/C including cost of all material, labour, T & P etc required for proper completion of work. (CSI No. 13.20)

Painting two coat with Acrylic emulsion paint of Berger/ Asian/ ICI or equivalent paint (Paint and water in the ratio 1:1 by volume) over prepared and primed surface of cement concrete, cement plaster and bricks including all labour, material and T&P etc required for proper completion of the work, (preparation of base with Birla putty etc. and a coating of primer shall be paid extra) . (CSI No. 13.25+13.26)

Painting Two coat with APEX or equivalent brand weather coat paint on new wall surfaces (well prepared with Birla putty and one coat of primer ICI or equivalent which shall be paid separately) including through washing with water including cost of all materials, labour, T&P required for proper completion of work. (CSI No. 13.22+13.23)

Painting or varnishing new iron works or new wood work with one coat of ready mixed priming paint and two coats of approved superior quality ready mixed paint LUXOL or equivalent brand or varnish including supply of all materials, labour& T&P etc. required for proper completion of the work (C.S.I. No. 13.01+13.02)

Grouting of vertical or inclined post of pale/chain/security fencing in true level, alignment and in plumb or inclination as required, including cost of all labour, materials and T&P required for proper completion of work. ( Post and concrete for grouting shall be measured separately) (CSI No. 9.28)

P/F Concertina coilfencing with required dia. 600 mm upto 3 M height of wall between existing angle iron ‘Y’ shaped placed 2.4 M or 3.0 M apart and with 6 horizontal R.B.T. stud tied with G.I. staples and G.I. clips to retain horizontal including necessary golts or G.I. barbed wire tied to angle iron all complete ( No. of rounds will be 7 to 8 in one Meter length) as per direction of Engineer I/C with reinforced barbed tape (R.B.T.)/ Spring core (2.5mm thick ) wire of high tensile strength of 165 kg/Sqmm with tape ( 0.52 mm thick ) of supreme make or equivalent and weight 43.478 gm/meter ( cost of MS angle, C.C. blocks shall be paid separately).(CSI No. 9.37)

Wiring point for light with 1.5 sq. mm FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit pipe CONCEALED IN THE WALL with 1sqmm FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit piano type switch and ceiling rose/angle/batten holder on 3mm thick phenolic laminated backelite sheet etc,complete in all respects,as directed, including maching colour wash.(NSI)

Wiring point for fan/fresh air fan(light duty exhaust fan) with 1.5 sq. mm FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit pipe CONCEALED IN THE WALL with 1sqmm FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit piano type switch and ceiling rose/angle/batten holder on 3mm thick phenolic laminated backelite sheet etc,complete in all respects,as directed, including maching colour wash.(NSI)

Wiring point for exhaust fan with 1.5 sq. mm FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit pipe CONCEALED IN THE WALL with 1 sqmm FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit,15A piano type switch and ceiling roseon 3mm thick phenolic laminated backelite sheet etc,complete in all respects,as directed, including maching colour wash.(NSI)

Wiring point for plug with 1.5 sq. mm FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit pipe CONCEALED IN THE WALL with 1 sqmm FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit,piano type switch and ceiling rose/angle/batten holder on 3mm thick phenolic laminated backelite sheet etc,complete in all respects,as directed, including maching colour wash.(NSI)

S/F of switch box made of 16SWG (1.5mm) thick MS sheet of 100x100x65mm size duly painted with red oxide primer and flush with wall including cutting of brickwork fixing it to level with cement sand mortar including matching color wash with all materials labour and T&P required for proper completion of work as directed at site by the EIC.(NSI)

S/F of switch box made of 16SWG (1.5mm) thick MS sheet of 150x150x65mm size duly painted with red oxide primer and flush with wall including cutting of brickwork fixing it to level with cement sand mortar including matching color wash with all materials labour and T&P required for proper completion of work as directed at site by the EIC.(NSI)

S/F of switch box made of 16SWG (1.5mm) thick MS sheet of 175x100x65mm size duly painted with red oxide primer and flush with wall including cutting of brickwork fixing it to level with cement sand mortar including matching color wash with all materials labour and T&P required for proper completion of work as directed at site by the EIC.(NSI)

S/F of switch box made of 16SWG (1.5mm) thick MS sheet of 250x250x65mm size duly painted with red oxide primer and flush with wall including cutting of brickwork fixing it to level with cement sand mortar including matching color wash with all materials labour and T&P required for proper completion of work as directed at site by the EIC.(NSI)

Supply and fixing of LED tube light of make Syska,Bajaj Phillips or equivalent make of 22watt on surface complete including all material and T&P etc in all respect as per direction of EIC (NSI)

Supply and fixing of LED bulb of make Syska,Bajaj Phillips or equivalent make of 12watt on surface complete in all respect as per direction of EIC (NSI)

Supply and fixing of LED flood light of make Syska,Bajaj Phillips or equivalent make of 100watt on surface complete in all respect as per direction of EIC (NSI)

Supply and wiring of sub main with two Nos 2.5 Sq.mm F.R.P.V.C insulated 1100V grade multi strand single core copper conductor, cable in 20mm dia heavy duty (2mm thick) PVC conduit concealed in wall with one number 1.5 sq.mm multi strand copper conductor, cable as earth continuity wire drawn in a conduit .(NSI)

Supply and wiring of sub main with two Nos 4 Sq.mm F.R.P.V.C insulated 1100V grade multi strand single core copper conductor, cable in 20mm dia heavy duty (2mm thick) PVC conduit concealed in wall with one number 2.5 sq.mm multi strand copper conductor, cable as earth continuity wire drawn in a conduit .(NSI)

Supply and fixing of 1200mm sweep ceiling FAN of make USHA/HAVELLS or its equivalent make including supply of all material, labour, T&P etc. required for proper completion of work as per direction of EIC . (NSI)

Supplying and fixing 63A DP isolator of approved make (Havells,Crompton, Anchor or equivalent) complete including all material and T&P etc in all respect as per direction of EIC(NSI)

Supply and fixing of 6 Amps to 32 Amps MCB 10KA HAVELLS or equivalent make including all materials, labour and t&p requiered for proper completion of work as per direction of EIC (NSI)

Supply and fixing of power plug with 15Amps. 250V. Flush type switch and 5pin 15A-250V. Flush type universal socket in suitable M.S.box of 175x100x50mm Size with phenolic laminated bakelite sheet cover 3mm. Thick fixed with brass machines screws and cup washer(NSI)

Supply and fixing of surface /flush mounting 12 ways SPN Distribution board with additional metal door without MCB complete in all respect as directed by EIC(NSI)

Supply and fixing of power plug with 20Amps. 250V. Flush type modular switch and 5pin 20A-250V. Flush type universal modular socket switch on concealed MS box including supply of all material, labour, T&P etc. required for proper completion of work as per direction of EIC (NSI)

Supply and fixing of electronic FAN regulator 120-280V ISI marked on the existing switch board incl. making connection, required mmaterial, labour T&P etc. for completion of the work to the satisfaction of EIC . (NSI)

Supply and burying of safe earthing electrode of T90 (hot dip galvanised) length upto 2M, outer pipre 50mm , Inner pipe 25mm,terminal dia 12mm, outer GI pipe of 16SWG and inner GI pipe of 12 SWG with hot dip galvanisation upto 100 micron field with crystalline condutive mixture having anti corossive and condutive property with 50kg activated soil (BFC) capable of reducing the soil resistivity wit good mixture of retaining capacity alongwith 30cm square CI frame with hinged cover and masonry housing (from electrode terminal to switch board, cost of 25x3mm GI strip will be extra) including all labour , material and T&P required for proper completion of work as per direction of EIC. NSI

Supply and installation of INDIA MARK HAND PUMP II including 150 mm dia ,70m deep boring up to second starta including supply and lowering 110mm to 63mm dia PVC pipe( 24m-110mm & 44m , 63mm,6 kg/sq.m) with required strainer,reducer joining 90 mm dia long cylinder,32mm dia GI pipe 3mlong including supply anf filling of course sand of approved quality (approx. .15 cum) including developing the bore well to achive clear and sand free water for continous 60 min. including cost of all material, labour and T&P and its cartage for installation of hand pump complete as per drawing including construction of 1.85 m dia chabutara with excavation of earth and laying 25mm C.C. floor 1:2:4 with cement, c.sand and 20mm stone ballast with water proofing compound over 100 mm thick c.c. 1:6:12 with cement, c.sand and 40 mm brick ballast and making side edge 115mm thick and 300 mm deep with brick work 1:4 and plaster the same with 1:4 mix with neat cement finish also including 115 mm wide drain in 1:4 brick work & plaster all around the periphery of plateform complete including supply of all materials,labour and T&P etc required for proper completion of work. Rate as per SE,7th Mandal,UP Jal Nigam, Gorakhpur Letter no 1045 DT 16.02.15 (CSI No.28.10)

Supply and fixing of 40.00 mm dia G.I. ("B" class ) column pipes JTC/ JINDAL make with column coupling socket as required for proper completion of work including all labour material & T&P. (CSI No. 19.22c )

Supply and fixing 40 mm dia support clamps for column pipes made out of MS flats, pairs of bolt-nuts etc complete with all material, labour, T&P. (CSI No. 19.24d)

Supply & Installation of 1.5 HP outlet 40mm dia. or more, Head 71/36, Discharge 2000/6000 LPH submersible pump of K.S.B/ CALAMA. or eqt. make including cost of labour, T&P and material required for completion of work. (CSI No. 19.32b)

Supply & installation of electrical control panel for 1.5/ 2 H.P pump set single phase of L&T / Havells or equivalent make for submersible pump / pumpset containing contractor relay condenser. (CSI No. 19.31b)

Supply & fixing of steel wire rope for submersible pump including cost of labour, T&P and material required for completion of work. (CSI No. 19.34)

Supply and fixing of 2.5 mm2 for pump above 1 HP and up to 3 HP. submersible cable Havels or equivalent make, for submersible pump complete in all respect. (CSI No. 19.33B)

M/S Grid Power Systems