CWE/P-91/2020-21 SPECIAL REPAIR TO BLDG NO NP-15 (OR LIVING ACCN) UNDER GE (WEST) PATHANKOT

Amount

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement motar of any description complete all as specified.

M&L brick work with sub class ‘B’ burnt bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

Description all as per item No.3.00 here-in-before, but except bricks. Note : Old bricks retrieved from demolition shall be used.

M&L Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean to any radius in half brick thick wall built in cement mortar 1:4, complete all as specified.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically described (reinforement cut as required to facilitate demolition), complete all as directed by Engineer-in-Charge.

M & L reinforced cement concrete 1:2:4 type B 1 ( 20 mm graded crushed stone aggregate ) as in lintels upto 1.50 m clear span seismic band and other similar bands, etc complete all as specified and as directed

M&L for mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia or securing with clips quality complete all as specified

M & L TMT bars, 8 mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia as in stirrups, complete all as specified

S & F Form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams etc with fair finished surface of concret complete all as specified & directed

Taking down cement plaster on stone or brick wall/ceiling etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

M&L 15mm thick rendering in Cement Motar 1:4 on brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified

M&L 15mm thick rendering in Cement Motar 1:6 on fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

M&L rendering 5 mm thick on ceiling surfaces in cement mortar 1:3 on fair faces of brick and finishing the surface even and smooth without using extra cement, complete all as specified.

M&L Non-skid cermic coloured tiles 7 to 8 mm thick (square / rectagular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over and including screed bed 15 mm thick in cement mortar 1:6 complete all as specified.

All as per ser item No.15.00 here in before but in skirting over and including 10mm thick cement rendering in cement mortar 1:4 complete all as specified.

M&L Glazed ceramic coloured tiles in vertical surface 300 x 450 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade over and including 10 mm thick cement plaster in cement mortar 1:4 as in backing coat rough finished surface complete all as specified.

M&L for granite stone slab 20 mm thick machine cut, bedded as in steps jambs pillars window cills cooking platform and the like and jointed with grey cement and pointed with white cement with admixture of pigments to match the shade of granite stone includingrounding to edges rubbing/grinding & mirror finish polishing/granite polishing over and including 15 mm thick screed bed in cement mortar 1:6, surface finished rough to receive top finish including dismantling of old broken granite complete all as specified and directed.

M&L Non abrasive paving (rectified endura) cement concrete coloured tiles 300 mm x 300 mm x 10 mm thick set jointed and pointed in neat cement slurry mixed with pigment laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M & L for 40 mm thick PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in sub base on floor, path, pavings etc.complete all as specified and directed

S&F 38 mm wide and 3 mm thick glass dividing strips in flooring by fixing in position and making square or rectagle for casting concrete is flooring.

M & L Providing PCC 1:2:4, type B-0(using 12.5 mm graded crushed stone aggregate)in bed block for fixing hold fasts on door & window frames including necessary form works complete all as specified.

M & L Cement Concrete 75 mm Type C-1 1:3:6 (using 20 mm graded crushed stone aggregate) as in sub base , filling and mass concrete complete all as specified and directed.

M&L 50 mm thick PCC as in plinth protection and path type C-1, 1:3:6 (20 mm graded agg) finishing cement surfaces even and fair complete all as specified & directed

Taking down chowkhats or frames exc 1.50 but n.exc 4 Sqm each (without talking off shutters from the frame) complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frames) area not exc1.5 Sqm each and removing from site.

S & F pressed steel frames 105 x 60 x1.25 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate complete all as spd and directed

S & F pressed steel frames 165 x 60 x1.25 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate complete all as spd and directed

S & F 35 mm thick framed, panelled shutter (two panel) of 2nd class hard wood with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supplied and fixed 35mm thick factory made 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats Note: wire cloth shall be measured separately

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with wood grain printed PVC sheet & 5 mm thick x 15 mm wide PVC sheet beading PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, work rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, & joined together with solvent convent supplying and fixing to frame at site as per specification & drawing.

S & F Steel windows/ventilator factory made , made out of mild steel tubular frame suitable for double shutters ie glazed and gauged shutters .Glazed shutter made out of Z section with sash bar and gauged shutter made out of Z section without sash bar including hinge, tower bolt, handle, grill 10 mm sq bar including one shop coat of red oxide primer over two coat of synthetic enamel paint taarred hold fasts, PCC blocks, including 3 mm thick sheet glass and galvanised 0.56 mm nominal dia of wire and average width of aperature 1.18 mm fixed with glass putty etc. all as shown on drg No CEPZ /TD-245/01 sheet 1/1 and CEPZ /TD -246/01 sheet No 1/2 & 2/2 complete all as spd including taking down existing spoiled and unserviceable windows of any type ( wooden/steel) complete all as specified.

M&L in repair for 18/19mm thick Prelaminated particle board,ISI marked, exterior grade fixed with screws to timber/PVC frame work in cup board shutters/shelves complete all as specified.

S & F Continuous (piano) hinges 30mm Width of flaps (when open) ,mild steel, bright finish or electrogalvanised complete all as specified and directed

S & F hasp and stapple, safety typeof Aluminium, anodised, including bolt to hinge type, fixed with screws of 100 mm size complete all as specified.

S & F 125 mm long Extruded Aluminium alloy handles, fabricated type, anodised. complete all as specified. ISI Marked

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified. ISI Marked

S & F 100 mm long medium weight, cold rolled mild steel Butt hinges complete all as specified. ISI Marked

S&F 300 mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified.

Supply and fix Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor Overall length of cover plate 150mm complete all as specified and directed.

Supplied and fixed 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

S & F 20 mm dia, decorative Aluminium alloy anodised curtain rails with bulb type brass metal brackets as directed by Engr-in-Charge complete all as specified and directed

S/F Aluminium alloy wire cloth/sheet. 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed

M & L preparation new of previously untreated steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint of colour as approved by GE complete all as specified.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide primer all as specified and directed.

M&L two coat of synthetic enamel paint over a coat of pink primer including preparation on new painted wooden or wood base surface of any description, not otherwise described over 10cm width or girth, complete, all as specified and directed

Supply and fxing in repairs,Vitreous china Wash hand basin, white, flat back of size 630x450mm excluding taps, brass chromium plated waste coupling, and waste pipe PVC 32mm dia pipe 750mm long (min) including bracket for fixing pipe including cutting for and pinning in ends of brackets or erecting stand etc , complete all as specified.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm, white, with integral foot rests with 'P; or 'S' trap, including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. in repairs including making good to floor complete all as directed.

S&F in repairs PVC low level flushing cistern, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets, connection to pipe all as directed.

Supplied and fixed in repairs Tubular towel rail, ISI marked 60cm long between flanges , 20mm dia 'D' type Brass Chromium plated incl necessary brackets, fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

Supply and fixing vitreous china white soap dish size 160x160x90mm fixed to plugs with chromium plated brass screws complete all as specified

Supplied and fixed in repairs Brass CP shower rose 125mm size with or without swivel joints including fixing to steel pipe or union complete all as specified and directed.

S&F in repair 15 mnm Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs 15mm Bib Taps of chromium plated fancy type long shank screwed for Iron Pipe or for brass ferrule complete all as specified and directed.

S & F in repairs Fancy type chromium plated with long shank and cup 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repairs Fancy type chromium plated with long shank and cup 20 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

M&L PVC connection 15mm size with PTMT nuts on both ends of length 450mm , complete all as specified.

S & F 50mm bore high density polyethylene pipes (HDPE) of pressure rating 6 Kgf/ Sq. Cm., fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed.

S&F GI water tubing of 15mm dia ,medium grade conforming to IS-1239(Part -1) including all fittings & fixed to walls,ceilings, & laid on floors (Concealed) complete all as specified and as directed by Engineer - in - Charge.

S&F GI water tubing of 20 mm dia ,medium grade conforming to IS-1239(Part -1) including all fittings & fixed to walls,ceilings, & laid on floors complete all as specified and directed

Re-fixing of old 15 mm bore steel tubing and connections in new or old position (walls, ceiling, floors etc.)(Concealed) complete all as specified and as directed by Engineer - in - Charge.

Refixing of old 20 mm bore steel tubing and connections in new or old position (walls, ceiling, floors etc.)

Dismantling of cast iron or reinforced concrtee drain pipes, jointed in cement mortar and taking out of trenches, if required Internal dia of pipe in 75mm/100mm complete all as specified and as directed.

Supply and fixed sand Cast iron soil, waste and vent pipes ISI marked, in any length with or without ears with cement joints, laid in trenches or in floors bore of pipe 75mm complete all as specified and as directed.

All as per item No 68 herein before but fixed to walls

Supply and fixed sand Cast iron soil, waste and vent pipes ISI marked, in any length with or without ears with cement joints, laid in trenches or in floors bore of pipe 100mm complete all as specified and as directed.

M & L Cast iron bends (ISI marked) (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 75mm, complete all as specified.

M & L Cast iron bends (ISI marked) (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 100mm, complete all as specified.

S & F 75mm bore cast iron cowls complete all as specified and directed.

M&L for 75mm dia PVC nahani trap, with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) complete all as specified and directed.

S &F in repair Grating round 100 mm size of PTMT, with or without waste hole.(Minimum weight 50gms) complete all as specified and directed.

Dismantling water tanks and removing from site capacity exceeding 500 ltr and not exceeding 1000 ltr complete all as specified and directed.

M&L Rotational moulded polythene water storage tank tripple layer cylindrical vertical with threaded closed top cover 500 litre capacity hoisted and fixed in position, connecting to inlet and outlet pipe connections, with and including 20mm dia GI wash out with plug, top cover complete all as specified and directed.

Ball brass valves, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule, 20mm bore complete all as specified and directed.

M&L for water proofing treatment by applying water proofing membrane APP (Atactic Polyprobhlene Polymer) modified membrane with non-woven polyster reinforcement/mat with thermal insulation with white mineral gravel finished on upper side of weight not less than 3.5 kg/sqm and thickness not less than 3 mm, laid by torch application method with overlap 100 mm on length side and 100 mm on the width side over a coat of hot industrial bitumen 85/25 applied @ 1.20 Kg/Sqm on prepared surfaces complete all as specified and directed and laid over 20 mm thick screed bed in cement mortar 1:4 incl mixed with water proofing admixture @ 200 ml per bag of cement including demolition of existing roof treatment of any description such as wornout tarfelt, cracked mortar,shurves vegetation,tree,terracing tile or concrete bedding and cleaning,washing down with water to remove all loose dirt, debris etc. complete all as specified and directed.

M&L for cutting out cracks to V-Section in existing roof or terracing, cleaning out wetting, grouting with cemnet and sand slurry 1:3 all as specified and directed.

M & L for post construction ATT treatment to points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same (using 20mm graded cushed stone aggregate) complete all as specified and directed.

M & L for providing and injecting chemical emulsion for post constructional anti-termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling 12mm dia upto 300mm deep and 300mm centre to centre and plugging holes in cement mortar 1:2 complete all as specified and directed.

M&L Cutting holes into or through brick walls in cement mortar superficial area exe 150 sqcm but n exe 400 sqcm including making good to the original surfaces of any description complete all as specified and directed.

S&F Steel work in tubular/ angle trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 including one shop coat of Zinc chromate primer paint including preparation of surface,complete all as specified.

S&F 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with L type or J type or cranked hook bolts and washers in roof,wall sheet 0.50mm thick, of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

Demolition and breaking up SWG drain pipes of internal dia 150 mm in cement mortar including bedding and haunching complete all as specified and directed.

M&L Concrete bed to drain pipes including packing under and haunching against the sides of pipes for 150mm drain pipe after they are laid in PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

M & L 150 mm dia Salt Glazed stone ware drain pipes grade 'A' laid in trenches and jointed and set in cement mortar 1:1 complete all as specified and directed.

M&L Precast cement concrete 1:2:4, type B1 (Using 20 mm graded granite stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and directed.

M&L Preparation of new plastered surface and applying two coats of oil bound distemper over a coat of primer including 1.5 mm thick wall care putty complete all as specified

M&L for preparing of newly plastered wall surfaces and priming with alkali resistant priming paint with two coats of Cement base paint complete all as directed and specified complete

Complete removal of existing treatment and preparing wall surfaces applying 1.5 mm putty complete and providing two coats of oil bound distemper all as specified and directed

Complete removal of existing treatment and preparing plastered wall surfaces and priming with alkali resistant priming paint with two coats of Cement base paint complete all as directed and specified complete

M&L for preparation of old plastered surfaces and applying one coats of white wash on ceiling all as specified.

S & F PVC (SWR) pipes (ISI marked) single socketed in any length with rubber ring joints of bore 110 mm fixing to walls and laid in floors incl taking down of old pipes complete all as specified and directed.

Supplied and fixed PVC (SWR) (ISI marked) bends any radius 110mm dia all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm with any type of soil complete all as specified and directed.

Removing excavated material (soil) exceeding 500m and not exceeding 1.5Km depositing where dircted at a level not exceeding 1.50m above the starting point, all as specified and directed.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

M&L Point wiring for light/fan/bell point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel sunkun boxes having thickness as specified 3mm bakalite laminated sheet for switches and sockets, including 1.5sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) (b) On RCC roof ceiling PVC conduit shall be provided on surface for fan with proper fixing clips all as directed.

Description all as per item No.101 here-in-before but for 5 Pin socket outlet 5 Amps point on independent board w complete all as specified and directed.

All as per above item no 101 here in before but for one 3 pin socket outlet 5 amp on same board with other switch complete all as specified and directed.

All as per above item no 101 here in before but call bell point complete all as specified and directed by E-in-C.

M&L Point wiring with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC concealed condult heavy duty 20 mm dia having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2 mm with 3mm bakalite laminated sheet ISI marked suitable for 5 pin 15 Amp socket outlet, including 2.5sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface finishing the surface to matching with the existing surface complete all as specfied and directed. Note : (a) Insulation test of point wiring (b) Colour coding is to be maintained (Ph-Red, N-Black, Earth- Green) complete all as specified and directed.

M&L Switch piano flush type 5 Amp 240 Volts single pole one way, (ISI marked), complete all as specified.

M&L Switch piano flush type 15 Amp 240 Volts single pole one way, (ISI marked), complete all as specified.

M&L Socket outlet 2 in 1, 3 pin , 5 Amp flush type, 240V complete all as specifed.

M&L Socket outlet 2 in 1, 3 pin, 5 & 15 Amp flush type, 230V complete all as specifed.

M&L Lamp holder insulated body with bakelite back plate having matching colour to holder for angle/batten fittings complete all as specified and directed.

M&L Electric bell 230 volts AC supply single pole all as specified and directed by Engineer-in-Charge.

M&L unsv Switch bell push flush type 5 Amp 240V (ISI marked) complete all as specified & directed

M&L Ceiling rose, 65x50mm three terminals complete all as specified & directed

M&L multi music bell 230 volts AC supply single pole all as specified and directed by Engineer-in-Charge.

M&L bell push flush type 5 Amp 240V (ISI marked) complete all as specified & directed

S&F replacement of ceiling fan regulator electronic socket type 5 stage speed variation ISI marked complete all as specified & directed

Supply and Fix in replacement existing unsv sleek LED mirror light fitting 2 feet long 1x10 W including LED tube 2 feet long of same make having ballast, bipin holder, connector block etc complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed.

M & L Energy new generation 10W LED bulkhead luminaire with opal diffuser with lamp complete all as specified and directed.

S&F in replacement of CFLs with LED smart lamp, B22 type 14 watt all as specified & directed

S & F energy saving decorative LED box type with Led Rod 20 watt (4 Feet), 230 volts, 6500 K energy efficient tube light fitting extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories prewired and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings. (Note power factor should not be less than 0.95) complete all as spd and directed.

S & F energy saving LED Rod 20 watt (4 feet), 230 volts, 6500 k energy efficient tube light complete all as spd and directed. Make of LED rod:-CROMPTON LTT8-20.

Supply & Fixing in replacement sheet metal enclosure single pole and neutral with 2 pin and earth plug and socket 20A 240V complete with one single pole MCB of capacity 20A complete all as specified.

S & F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 12 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed by Engr-in-charge.

S & F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 6 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed by Engr-in-charge.

S & F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 4 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed by Engr-in-charge.

S & F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 2 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed by Engr-in-charge.

S & F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed by Engr-in-charge.

M & L MCB SP 240 volts any rating from 6 to 40 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed by Engr-in-charge.

M & L MCB SPN 240 volts any rating from 6 to 40 amps, with rupturing capacity 10 KA, including providing thimble for out going cablescomplete all as specified and directed by Engr-in-charge.

M&L Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, connected to galvanized iron wire 4mm dia as earth lead by means of bolts,nuts and washers of GI up to test point,earh lead wire of size 4.0 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3 of SSR Part I, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI medium grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. Note: The rate quoted include cost of 7.5 metre earthing wire with protection pipe.

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

GANDOTRA CONSTRUCTION CO

M/S SALARIA BUILDERS

malghotra construction co

kay gee construction co

Jay Ann Construction Company