Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹24.6 LAccepted-AOC | L1 | Accepted-AOC Being lowest | |
| 2 | L2₹27.7 L+₹2.9 L (11.5%)Rejected-Finance E 11 CWE WELLINGTON A I A II A V B I | KOLKATA | WEST BENGAL | 700001 | L2 | Rejected-Finance Not being lowest | |
| 3 | L3₹29.9 L+₹5.1 L (20.4%)Rejected-Finance 18 KUSHAL LAYOUT 1ST CROSS KAGGADASAPURA CV RAMAN NAGAR POST BENGALURU 560093 | BENGALURU | BENGALURU URBAN | KARNATAKA | 560093 | L3 | Rejected-Finance Not being lowest |
Tender Value
₹22 L
EMD Value
₹44,000
Closing Date
20 Sept 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
CWE WELLINGTON
Headquarters, Commander Works Engineers, Military Engineer Services Ministry of defence Wellington, Barraks-Post, The Nilgiris, PIN 643231
PROVISION OF GUARD REST ROOM ALONGWITH TOILET FACILITY NEAR LOCAL REPAIR WORKSHOP AT MADUKKARAI , CERTAIN REVENUE AND MINOR WORS AT ARMY AREA COIMBATORE UNDER AGE (I) COIMBATORE. CONTENTS
2022_MES_521692_3
84445/E8
Open Tender
Civil Works
Item Rate
180 days
COIMBATORE
Class E
Category a(i)
8 documents required · 8 mandatory
₹500
AGE (I) COIMBATORE
₹44,000
Yes
10 Oct 2022
31 Aug 2022
28 Sept 2022
31 Aug 2022
20 Sept 2022
8 Sept 2022
1 Sept 2022 - 7 Sept 2022
Amount
B/R PORTION Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in hard/ dense soil all as specified and as directed.
Excavating in trenches, n.exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/ dense soil complete all as specified and as directed.
M & L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and as directed.
M & L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.
M & L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.
M & L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed.
Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm in hard/dense soil complete all as specified and as directed
Removal of excavated materials (soil) to a distance exc 5Km and not exc 10Km and depositing where directed at a level n.exc 1.5m above the starting point all as specified and as directed.
M & L for PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.
M & L for Brickwork in CM (1:6) with subclass ‘B’ bricks, straight or curved on plan exceeding 6m mean radius complete all as specified and as directed.
M & L 15mm thick rendering in CM (1:4) on fair faces of brick wall/ concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.
M & L 15mm thick rendering in CM (1:6) on other than fair faces of brick wall/ concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.
M & L for mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for column hooking ends and binding with and including mild steel wire (annealed) not less than 0.9m dia or securing with clips all as specified and as directed.
Description all as per Item No 13 above but 6 to 8 mm dia as in stirrups complete all as specified and as directed.
M & L for cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) in lintel upto 1.5m clear span/ lintel band, in coping including necessary form work complete all as specified and as directed.
M & L for hard core of broken stone or boulders n.exc 63 mm deposited, spread and levelled in layers n.exc 15cm thick, water and rammed to a true surface complete all as specified and as directed.
M & L for providing 100mm thick PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed.
M & L for providing 25mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in sub base, flooring using with/ without extra cement (as applicable) complete all as specified and as directed.
M & L for Non-skid coloured ceramic tiles 7 to 8mm thick, area of each tile exc 0.18 Sqm and n.exc 0.38 Sqm (square/ rectangular) set and jointed in neat cement slurry and pointed in coloured cement to match as in floors etc., laid over and including 15mm thick screed bed or bedding layer in CM (1:6) for laying floor finishes complete all as specified and as directed.
M & L for Non-skid coloured ceramic tiles 7 to 8mm thick, area of each tile exc 0.18 Sqm and n.exc 0.38 Sqm (square/ rectangular) set and jointed in neat cement slurry and pointed in coloured cement to match as in vertical surfaces such as skirting, dado etc., laid over and including 10mm thick rendering/ backing coat in CM (1:3) complete all as specified and as directed.
M & L for glazed ceramic tiles of size 300 x 250 x 8-10mm thick set and jointed in neat cement slurry and pointed in coloured cement to match on vertical surfaces such as skirting, dado etc., laid over and including 10 mm thick rendering/backing coat in CM 1:3 complete all as specified and as directed.
S & F pressed steel frames of size 165 x 60 mm for doors with one or more rebates including necessary fixing lugs, lock strike plate etc , and filling with PCC complete all as specified and as directed.
M & L for providing PCC (1:3:6) type C-0 (using 12.50 mm graded stone aggregate) as in filling hollow of pressed steel frame, bed blocks for hold fast including formwork complete all as specified and as directed.
S & F 30 mm thick, second class hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and as directed.
S & F second class hard wood 35 mm thick glazed and skeleton shutters, open rebated prepared to receive glass/gauze etc., edges of framing, divided into squares with plain chamfered or rounded, fitted with cut mitered beads for securing glass/gauze all as specified and directed including chiselling and planing of wooden existing frame to receive the shutter complete all as specified and as directed. Note: Glazing and gauze will be measured separately.
S & F 150mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.
S & F 300 mm long, aluminium alloy, anodized sliding door bolt, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts of extruded section complete all as specified and as directed.
S & F 150mm size, mild steel butt hinges, medium weight, cold rolled complete all as specified and as directed.
S & F aluminium handles, cast type, anodised 150 mm long complete all as specified and as directed.
S & F floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel pin fixed to door, overall length 140 mm all as specified and as directed.
S & F steel windows with side hung shutters incl projecting type hinges with steel handles, steel peg stay complete with glazing dove tail or welded complete all as specified and as directed.
S & F steel windows with side hung shutters incl projecting type hinges with steel handles, steel peg stay complete without glazing dove tail or welded complete all as specified and as directed.
M & L 4 mm thick sheet glass ordinary quality and glazing with oil putty in squares n.exc 0.5 Sqm in each pane all as specified and as directed.
S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.
M & L for preparation of new steel iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.
M & L for preparation of new wood or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.
M & L for providing 75mm thick cement concrete (1:3:6), type C-1 (using 20 mm graded stone aggregate) as in plinth protection complete all as specified and as directed.
M & L for providing 75mm thick cement concrete (1:3:6), type C-2 (using 40 mm graded stone aggregate) as in plinth protection and finished even and smooth with using extra cement complete all as specified and as directed.
S & F for steel work in tubular trusses including special shaped washer etc., complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 complete all as specified and as directed.
S & F pre-painted galvalume aluminium zinc coating GI based corrugated sheet 0.50 mm thick of any colour having tensile strength 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and as directed.
S & F pre-painted galvalume aluminium zinc coating GI based plain sheet 0.45mm to 0.50 mm thick of any colour having tensile strength 550 MPa as in ridges, fixed with self tapping screws all as specified and as directed.
S & F 15mm bore, unplasticised PVC pipes of pressure rating 10 Kgf/Sqcm fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.
S & F 20mm bore, unplasticised PVC pipes of pressure rating 10 Kgf/Sqcm fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.
S & F bib tap 15mm dia, cast copper alloy, fancy type chromium plated, screwed down, screwed for iron pipe or ferrule complete all as specified and as directed.
S & F sink with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.
M & L for preparing surfaces of wall and applying two coats of oil bound distemper over a coat of wall care putty and a coat of primer on newly plastered wall surface complete all as specified and as directed.
M & L for preparing surfaces of wall and applying two coats of cement based paint on newly plastered wall surface complete all as specified and as directed.
M & L for false ceiling using GI snap grid system with roll-formed out of hot-dip galvanised steel capping (powder coated), main runner 38 x 24mm, cross tee 29 x 24mm and wall angle 24 x 24mm and thickness not less than 1 mm, members suspended with hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size, 60mm long and expansion hold fasteners 12.5mm dia. 40mm long , with 4mm thick designer ceiling board of any texture (Lake & Hill, Oceanic, Cascade or Electra) as approved by GE, all as per Everest Ceiling grid system "Regular T-2430" or its techno-commercially equivalent as approved by GE complete all as specified and as directed
Excavation over areas, n.exc 1.5m deep for foundation etc & getting out in hard/dense soil all as specified and as directed.
Excavation over areas, exc 1.5m deep & n.exc 3.00m in deep; for foundation etc & getting out in hard/dense soil all as specified and as directed.
Removing excavated material (soil) to a distance n.exc 50m & deposited where directed at a level n. exc 1.5m above the starting point all as specified and as directed.
M & L for broken brick bats of guage 80 to 150mm loose filling in soakage pits, soakage wells etc., complete all as specified and as directed.
M & L for providing 80mm thick PCC(1:2:4) type B-2 (using 40mm graded stone aggregate) as in flooring finished even and smooth using extra cement all as specified and as directed.
M & L for Precast cement concrete (1:3:6) type C1 (using 20 mm graded stone aggregate) block masonry with solid blocks, exc 10 cm in width and set in cement mortar (1:4) complete all as specified and directed.
M & L for providing precast cement concrete (1:3:6) type C-1 (using 20mm graded stone aggregate) solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in CM (1:4), complete, in walls all as specified and as directed.
M & L for rendering 10mm thick in CM (1:4) mixed with WPC as per manufacturer's instruction on fair faces of brick work or concrete surfaces and finished fair and even and smooth without using extra cement all as specified and as directed. Note: WPC shall be measured and paid separately.
Supply only water proofing compound conforming to IS-2645 1975 all as specified and as directed.
M & L for use and waste of timber as in formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exec 20Cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n.exc 20cm complete all as specified and as directed.
M & L for use and waste of timber as in formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surfaces of concrete flat all as specified and as directed.
M & L for RCC (1:2:4) (Nominal Mix) type B-1 (using 20 mm graded stone aggregate) as in beams and columns in floors roofs, landing, balconies, canopies,deck slab and in shelves and like complete as specified and as directed.
M & L for Precast Reinforced cement concrete (1:2:4) type B-1,(using 20 mm graded stone aggregate) as in cover slabs (for manholes), chajjas, sunshades, shelves etc with plain fair faces including setting in CM (1:4) all as specified and as directed. Note : Reinforcement shall be measured and paid seperately.
M & L for PCC (1:3:6) type C-1 (using 20mm graded stone aggregate) as in coping including necessary form work all as specified and as directed.
M & L for PCC (1:3:6) type C-2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 110 mm bore complete all as specified and directed.
M & L for 110mm bore PVC (SWR) pipes, type 'B', single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.
S & F PVC gully trap with cover of size 125mm x 110mm, setting and jointing with solvent cement including PCC bed complete all as specified and as directed.
M & L for 75mm bore PVC (SWR) pipes, type 'B', single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.
S & F PVC (SWR) vent cowl 75mm bore complete all as specified and as directed.
S & F PVC (SWR) bends any radius 75mm bore incl access door all as specified and as directed.
S & F PVC (SWR) junction single, (Single T) equal or unequal 75mm bore all as specified and as directed.
S & F PVC (SWR) bends any radius 110mm bore incl access door all as specified and as directed.
S & F for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat, square tube sections etc.,) including distance pieces, cleats etc., conforming to Fe 410-W (Gde-E- 250) quality- A all as specified and as directed.
M & L for use and waste of timber as in formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for fair finished surfaces of concrete flat all as specified and as directed.
M & L for use and waste of timber as in form work to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete square, rectangular or polygonal complete all as specified and directed.
M & L for RCC (Design Mix M-25) (using 20 mm graded stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.
M & L for RCC (Design Mix M-25) (using 20 mm graded stone aggregates) as in columns, pillars, piers, posts and struts etc complete all as specified and as directed.
M & L for providing 100mm thick PCC(1:2:4) type B-1 (using 20mm graded stone aggregate) as in sub base, floors and pavings complete all as specified and as directed.
M & L for glass dividing strips of width of 22mm and 3mm thick inserted in position in concrete bedding complete all as specified and as directed.
M & L for PCC(1:2:4) type B-2 (using 40mm graded stone aggregate) as in ramp complete all as specified and as directed.
M & L for RCC (Nominal Mix) (1:2:4) type B-1 (using 20mm graded stone aggregate) for foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and as directed.
M & L for RCC (Nominal Mix) (1:2:4) type B-1 (using 20mm graded stone aggregate) for columns, etc, complete all as specified and as directed.
M & L for RCC (Nominal Mix) (1:2:4) type B-1 (using 20mm graded stone aggregate) for beams, cantilevers, bressumers, lintels over 1.5m span, complete all as specified and as directed.
M & L for use and waste of timber as in form work to sides and soffits of rough finished floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc alos splays between floors, and beams,etc compelte all as specified and as directed.
M & L for RCC (Nominal Mix) (1:2:4) type B-1 (using 20mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies canopies, deck slabs and in shelves and the like complete all as specified and as directed.
M & L for use and waste of timber as in formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surfaces of concrete flat all as specified and as directed.
M & L for use and waste of timber as in form work to chullah hoods, chajjas, troughs and similar items including edges,etc compelte all as specified and as directed.
M & L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers, and binders in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire complete all as specified and as directed.
M & L 20mm thick cement plaster in CM (1:3) on top of roof slab complete all as specified and as directed.
M & L for roof treatment with following specification complete all as specified and as directed by Engineer-in-Charge :- (i) Applying evenly a tack coat of bitumen primer @ 0.3 Kg/ Sqm. (ii) Laying a coat of hot bitumen 85 x 25 @ 1.2 Kg per Sqm. (iii) Laying APP modified membrane weighting not less than 3 to 4 Kg/Sqm in 100 mm over laps both longitudinally and transversally and overlaps to be sealed by torch, membrane shall be taken upto the thickness of slab/front fascia. (iv) Cleaning the surfaces and finally painted at the top with a coat of bituminous aluminium paint @ 100 gms/Sqm over Bituminous coat complete all as specified and as directed.
M & L for extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc., all as specified and as directed.
M & L for Moorum/Red Bajri filling in floors or pavings, laid in layers n.exc 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.
M & L for external rendering 15mm thick in CM (1:4) mixed with WPC as per manufacturer's instruction on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed. Note : WPC shall be measured and paid separately.
M & L for rendering to ceiling in 5mm thick on fair faces concrete surface in CM (1:3) finished even and smooth without using extra cement complete all as specified and as directed.
M & L for glazed ceramic coloured tiles of size 350 x 250 x 7 mm/ 450 x 350 x 7mm thick on vertical surfaces such as skirting, dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and incl 10mm thick in CM (1:3) as backing coat for fixing dado tiles all as specified and as directed.
S & F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed
S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and as directed.
S & F pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, lock strike plate etc, and filling with PCC complete all as specified and directed
S & F 35mm thick second class hardwood plain, framed, paneled shutters (any number of panels) with panels of timber flat both sides (feather edged) or of veneered particle board medium density, wood particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats all as specified and as directed.
S & F steel ventilators with top hung shutters including hinges, steel peg stay, fixed including welding complete all as specified and as directed. (Box type frame and shutters)
M & L for oil bound distempering two coats over a coat of alkali resistant priming paint including preparation of new plastered or unplastered surfaces of wall complete all as specified and as directed.
M & L for three coats of white wash on ceiling surfaces including preparation complete all as specified and as directed
M & L for preparation of newly plastered surfaces of wall and applying three coats of cement based paint over a coat of primer complete all as specified and as directed.
M & L for 4mm thick figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 Sqm in each pane complete all as specified and as directed.
S & F chimney bars (straight or camber) bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in steel frames, L or T section supports for shelves etc, including welding and similar articles conforming to Fe 290 Gde E-165 complete all as specified and as directed.
S & F 200mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.
S & F Butt hinges, 100mm size medium weight, cold rolled mild steel, and fixed complete all as specified and as directed.
M & L for treating ends of posts, back of chowkats etc., area tarred exc 0.10 Sqm but n.exc 0.50 Sqm each including preparation of the surfaces and treated with coal tar or black biuminous paint complete all as specified and as directed.
M & L for sanding newly tarred surfaces with clean sand sharp sand complete all as specified and as directed.
S & F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.
S & F low level PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, white with inlet, ball valve, float and handle including brackets complete all as specified and as directed.
S & F Health faucet (Jet Spray), CP 15mm dia with flexible pipe and fixing nut etc complete all as specified and as directed.
S & F PVC Connections 15mm size with PTMT nuts of length 750mm all as specified and as directed.
S & F Pillar taps, 15mm, fancy type, cast copper alloy with capsten heads,chromium plated,screwed down high pressure, screwed for iron pipe and fixed all as specified and as directed.
S & F stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type chromium plated, 15mm bore all as specified and as directed.
S & F Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges all as specified and as directed.
S & F Harrison rails of anodised aluminium alloy fixing with brackets, stops,rollers etc all as specified and as directed.
S & F vitreous china wash basin, white, flat back size 550 x 400mm inluding cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe all as specified and as directed.
S & F 110mm bore, PVC (SWR) Tee any radius, fitted with oval access door all as specified and as directed.
S & F 110mm bore PVC (SWR) bends any radius complete all as specified and as directed.
S & F PVC (SWR) vent cowl of size 110mm bore complete all as specified and as directed.
M & L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed
M & L for precast RCC hume pipe septic tank for 25 users and of dia 1.20m , length 2.40m including transportation complete all as specified and as directed.
Fixing of septic tank in position using crane complete all as specified and as directed.
M & L for 900mm dia and 1.50m depth precast soakage well including transportation complete all as specified and as directed.
E/M PORTION S & F three phase electronic energy meter, phase direct connection type KWH meter, tamper proof, plastic body with optical port with box with LCD display as per IS 13779, ISI marked, 20-100 Amps capacity optical communication port complete all as specified and as directed. Note : Rate quoted shall deemed to be included the CTs if needed to fix the energy meter.
M & L for fabrication and installation outdoor type feeder pillar box for fixing of energy meter overall dimension of size 0.45m x 0.70m x 0.40m made of 3.15mm thick CRCA sheet, MS equal angle 35mm x 35mm x 5mm, MS flat 40 x 5mm duly painted with two coats of synthetic enamel painyt over a coat of red oxide primer both sides to be mounted on PCC/ brick foundation by grouting of MS bolts, nuts and washers complete all as specified and as directed.
M & L for single core 6 Sqmm FRLS copper cable connection from CT unit inside the LT panel to the metering chamber drawn through flexible conduit pipe complete all as specified and as directed.
M & L for point wiring using with multistranded copper conductor 1.5 Sqmm nominal cross-sectional area single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade, ISI-694 marked with valid CML No. in and drawn through casing and caping and mild steel/ pressed steel sunken box for modular switches (with earth dolly) duly painted with two coats of anti corrosive paint /aluminium paint over a coat of red oxide primer internally and two coats of black bituminous paint over a coat of red oxide primer externally including PVC insulated multistranded copper conductor 1.5 Sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth duly completed all as specified and as directed by Engr-in-charge for the following :- (a) One light point controlled by one switch 5 amps Make:Havells/Finolex/Polycab Note : (i) The wiring shall be done in proper color coding using red, yellow, blue for phases, black for neutral and green for earth. (ii) The cost of making good the disturbed surfaces & matching to the original/existing surface is deemed to be included in the quoted rate.
Description all as per Item No 128 above but One fan point controlled by one switch 5 amps and regulator complete all as specified and as directed.
Description all as per Item No 128 above but One socket outlet 3 pin 5 amps on independent board complete all as specified and as directed.
Description all as per Item No 128 above but 4 Sqmm PVC insulated and PVC unsheathed copper multi stranded conductor cable and 4 Sqmm multi stranded copper conductor for earth wire for 3 pin 15 Amps power points complete all as specified and as directed.
S & F switch piano flush type 5 Amps Single Pole one way complete all as specified and as directed. Make : Anchor/ Schneider/ Havells
S & F switch socket combination 2 in 1, 5 Amps, flush type complete all as specified and as directed. Make : Anchor/ Schneider/ Havells
S & F for switch socket combination 2 in 1, 3 Pin, 5 Amps & 15 Amps, Universal type complete all as specified and as directed. Make : Anchor/ Schneider/ Havells
S & F step type electronic fan regulator flush type all as specified and as directed. Make : Anchor/ Schneider/ Havells
S & F ceiling rose bakelite with three terminals complete all as specified and as directed.
S & F LED lights fitting 1 x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make : Havells/ Philips/ CG or equivalent as approved by GE.
S & F in replacement MCB DB, SPN 4 way suitable for single phase 240 volts with double door type suitable for mounting incoming and outgoing MCB's single/double pole complete all as specified and directed.
S & F MCB SPN 32 Amps complete all as specified and as directed. Make:Havells/ Legrand / Standard/ L & T
S & F MCB SP 6 to 32 Amps complete all as specified and as directed. Make:Havells/ Legrand / Standard/ L & T
Earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground earth pit not less than 2.25m deep below ground level with top edge of the plate not less than 1.5m below normal ground level connected to GI earth wire 4mm dia by means of bolts and nuts washers mase out of GI and earth strip protected by Galvanized pipe light grade 15mm bore, 20 mm bore medium grade watering pipe and connected to main control board all as shown in Electrical plate No 5 of SSR part I including necessary earth work and excavations in any type of soil PCC 1:2:4 type B1 chamber with 40mm thick, RCC 1:2:4 cover slab with 6mm dia MS bars etc complete all as specified and as directed. Note:- On testing after completion, if the desired earth resistance is not obtained the earthing will be redone to the entire satisfaction of Engr-in-Charge at no extra cost
S & F ceiling fans energy efficient, 50 Watts complete with three blade, down rod, accessories 230 Volts, 1200mm sweep with squirrel cage induction motor complete all as specified and as directed.
Supply, laying and testing XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable heavy duty with aluminium conductor 1100 volts grade cross sectional area 4 Sqmm, 2 core complete all as specified and as directed.
Excavation in trenches n.exc 1.5 m wide and n.exc 1.5m deep for foundation and getting out in hard/ dense soil all as specified and as directed.
Supply and laying well burnt B class brick for cable protection of old size all as specified and as directed.
Supply and filling in and spreading of tibba sand or riddled sand for cushioning and covering of the UG cable in trenches all as specified and as directed.
M & L for laying XLPE insulator armoured heavy duty electric cable with aluminium conductor 1100 V grade cross section 10 Sqmm 2 Core laid in ground/ fixed on wall complete all as specified and as directed.
M & L for cutting the existing road/ hardstanding made of concrete or premix carpet, WBM, soling and moorum filling including excavating for laying the cable/ pipe, width 0.5 mtr and depth 0.7 mtr and making good the road/ hard using all old/ new materials as required at site to match with the existing surface all as specified and as directed.
S & F GI tubing light grade 32mm nominal dia in trenches/ road/ pole for cable protection including removing old pipe all as specified and as directed.
S & F MCB DB double door, 4 way SPN surface mounted and matching with the existing surface with connections complete all as specified and as directed.
S & F exhaust fan, steel body, AC, single phase, 230 Volts of size 300mm sweep with blades and frame and louvres and cutting holes into or through brick wall/ stone masonry wall built in cement mortar approx 350mm in round with good surface and material in fixing or MS nut and bolts with check nuts all as specified and as directed.
Supply and fixing LED light fitting mirror type with high output diffuser 2 feet, 1 x 10 Watts, 220 Volts, AC, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. Make : Havells/ Philips/ Luker/ CG or equivalent as approved by GE.
Supply and fixing LED building security light fitting 35 Watts, 230 Volts AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.
VENKATESH
TECKXPERT ENTERPRISES
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .