ADDN/ALTN TO SMQs IN BASRA AREA, PROVISIONING /INSTALLATION OF AB CHOCK GUIDE RAIL AND COMMERCIAL POWER SUPPLY AT AWS AND PROVN OF SPLIT AC (QTY-02) AT AFS HASIMARA

Amount

Dismantling of floor, hearth or wall tiles including cement mortar bedding (but not backing), removing serviceable tiles or stone and remvoing rubbish off the premises, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match the surfaces over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for joint free glazed ceramic coloured tiles of size 350 x 250 x 7mm/450 x 300 x 7mm thick each as in skirting or dado on vertical surfaces of wall, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces over and including 10mm thick rendering in CM (1:4), complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid dry and pointed, complete all as specified and as directed.

M&L for 18-20mm thick Granite (of any type) tiles, machine cut, bedded and jointed with gray cement slurry and pointed with white cement with admixture of pigment to match with shade of granite stone including grinding and polishing, over and including 20mm thick screed bed in CM (1:6), complete all as specified and directed.

Rounding to edges of granite slabs one edge, such as in cooking platform, steps and other similar situations, complete all as specified and as directed.

Demoliton of cement concrete (unreinforced) in ground floors and pavings n. exc. 15cm thickness (below or above ground level), complete all as specified and directed.

M&L for 75mm thick PCC (1:2:4) type B- 2, (using 40mm graded crushed stone aggregate) for pavings or plinth protection etc, finished surfaces of concrete even and smooth (without using extra cement), complete all as specified and directed.

M&L for forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound grade 'B', thichness of slab 75mm, complete all as specified and directed.

Taking down cement plaster of any description any thickness incl racking out joints hacking for keys scrubbing down with water etc, including disposal of debris and rubbish to a distance not exceeding 100m, complete all as specified and directed.

Demolition of bricks work or stone/boulder masonary, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework and precast concrete aritcles, complete all as specified and directed.

M&L for brickwork with fly ash bricks, old size, straight or curved on plan exc. 6m mean radius, built in CM (1:6), complete all as specified and directed.

M&L for brick work with fly ash bricks, old size straight or curved on plan to any radius, built in CM (1:4) as in half brick thick wall, complete all as specified and directed.

M&L for 10mm thick cement plaster on fair faces of brick work or concrete surfaces in CM (1:6) and finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 15mm thick in two coats (10mm under layer + 5mm top layer) on fair faces of brick work or concrete surfaces of wall in CM (1:4), mixed with water proofing compound on top layer as per manufacturer's instructions and finished the surface even and fair without using extra cement, complete all as specified and directed. (Note : WPC shall be measured and paid separately as 'supply only')

Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification, complete all as directed.

M&L for preperation of newly plastered wall surfaces and applying two coats of oil bound distemper over including a coat of 3mm thick wall care putty, complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over and including a coat of alkali resistant primer, complete all as specified and directed.

M&L for complete removal of existing treatment of wall surfaces and applying two coats of oil bound distemper over and including a coat of 3mm thick wall care putty, complete all as specified and directed.

M&L for complete removal of existing treatment of ceiling surfaces and applying two coats of oil bound distemper, complete all as specified and directed.

M&L for complete removal of existing treatment of wall surfaces and applying two coats of cement base paint, complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth, not otherwise described, and applying one coat of synthetic enamel paint (1st grade quality), complete all as specified and directed.

Taking down 15mm bore steel water tubing and connection from wall/ceiling surfaces including cleaning for refixing or removal from site of work, complete all as specified and directed.

Taking down 20mm bore steel water tubing and connection from wall/ceiling surfaces including cleaning for refixing or removal from site of work, complete all as specified and directed.

Taking down 25mm bore steel water tubing and connection from wall/ceiling surfaces including cleaning for refixing or removal from site of work, complete all as specified and directed.

S&F CPVC pipe of size 20mm dia, SDR 11 & plain CPVC SDR 11 fittings complete, fixed in floors/wall/ceiling with necessary saddle/clamps fixed with CPVC solvent cement and testing, complete all as specified and directed.

S&F CPVC pipe of size 25mm dia, SDR 11 & plain CPVC SDR 11 fittings complete, fixed in floors/wall/ceiling with necessary saddle/clamps, fixed with CPVC solvent cement and testing, complete all as specified and directed.

S&F in repair 20mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipes, complete all as specified and directed.

S&F in repair 25mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipes, complete all as specified and directed.

S&F in repair vitreous china squatting pan,"Orissa pattern" white, size 580mm x 440mm with integral foot rest, 'P' or 'S' trap, including connection to trap, and to flushing pipe, anti -syphonage pipe etc., complete all as specified and directed.

S&F in repair EWC vitreous china wash down water closet pan, white including connection to drain or outgoing pipe and flushing pipe, anti syphonic pipe with seat and cover including making good damged/distrubed surfaces, complete all as specified and as directed.

S&F in repair 10 ltrs capacity low level valve less PVC syphonic action type flushing cistern white with inlet ball valve, float and handle including brackets and all fittings, flush pipe and connection to pipes, complete all as specified and directed.

S&F in repair vitreous china wash hand basin white flat back of size 550mm x 400mm including brackets, PVC waste pipe 32mm bore, waste coupling including cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S&F in repair CP pillar tap, 15mm bore, cast copper alloy, capstan head, screwed down high pressure with or without lettered “Hot’ or “ Cold” with long screwed shanks and fly nuts, screwed for iron pipe and fixed, complete all as specified and directed.

S&F in repair 15mm bore, bib tap, cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F in repair 15mm bore, fancy type, chromium plated, stop valves, concealed type, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed, complete all as specified and directed.

S&F in repair 15mm bore, two way bib tab (fancy type), chromium plated, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair 15mm bore angular valve, chromium plated, cast copper alloy, screwed down, high presure with crutch or butterfly handle screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair kitchen sinks with drainage board made of 1mm thick stainless steel (SS-304 grade) with plugs, washers and wastes, including bedding in cement mortar to wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

S&F in repair 15mm bore, brass chromium plated sink cock, fency type (table mounted) with swivel spout 215mm long, complete all as specified and directed.

S&F in repair swivel shower rose 125mm size with or without swivel joint, brass, chromium plated, including fixing with 15mm bore pipe or union, complete all as specified and directed.

S&F in repair CP shower arm 15mm size, 195cm long with bend of 45 degree with flange, complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

S&F 32mm dia collapsible waste pipe 800mm long for wash hand basin and sink, complete all as specified and directed.

S&F 25mm dia stainless steel towel rail 60cm long, fixed with and including chromium plated brass screws, complete all as specified and directed.

S&F glass shelf of size 12cm wide x 60cm long and not less than 5.5mm thick with brass brackets for wash hand basin etc, complete all as specified and directed.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing to waste pipe with solven cement, complete all as specified and directed.

S & F in repair 110mm bore PVC (SWR) rain water pipes,single sockets, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 110mm bore, PVC (SWR) bends of any radius with access door, complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) rain water pipes, single sockets, in any length with sealant rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm bore, PVC (SWR) bends of any radius, with access door complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction, (single T), equal or unequal, with access door complete all as specified and directed.

S&F CP grating 100mm dia, fixed with white cement, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks, (made of 100% virgin and food grade plastic), triple layered, (cylindrical vertical with closed top), ISI marked, confirming to IS 12701-1996, hoisted and fixed in position all as specified in SSR Part I (1000 ltr capacity) including 25mm Nipple and 25mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed to 20mm bore pipe inculding dismantling of old unserviceable water tank of any capacity, complete all as specified and directed.

S&F in repair PTMT nipple suitable for HDPE water storage tank (min wt 45gm), complete all as specified and directed.

Taking down chowkats with shutter (without taking off shutter from the frame) not exc. 1.5 Sqm each., complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutter from the frame) exc 1.5 Sqm but n.exc. 4 Sqm each, complete all as specified and directed.

Taking down shutter of any description exc. 1 Sqm but n.exc 2 Sqm each, complete all as specified and directed.

Taking down shutter of any description exc 1 & n.exc 2 Sqm each and refixing in same opening, complete all as specified and directed.

S&F 125 x 60mm size factory made pressed steel frames for doors, made out of 1.25mm thick PBI sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

Cutting holes in brick walls built in CM for inserting hold fasts and making good dismantled portion in CM (1:3) or PCC (1:2:4), type B-1 (using 12.5mm graded crused stone aggregate) as in depth of embedded portion of hold fast n. exc. half brick, complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet reinforced with M.S. Square tube and edges will be painted to match with prelam sheet, as per specification & drawings, complete all as specified and directed.

S&F factory made solid PVC moulded door shutter, with particle board core 28mm to 30mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm plain PVC sheet on back face, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S& F 30mm thick flush door shutter, membrane doors, decorative finish on one side duly finished and polished and other side all as per manufacturers directions, as per tint/colour including necessary teak wood lippings, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, any numbers edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a) and fitted to chowkats, complete all as specified and directed.

S&F for 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

S&F butt hinges of size 100mm, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type C-21, complete all as specified and directed.

S&F aluminium alloy anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheets, cast extruded sections and fixing bolt and sliding bolts of extracted sections, complete all as specified and directed.

S&F 150mm long aluminium anodised, barrel tower bolt of extruded section, complete all as specified and directed.

S&F 150mm long aluminium handle, cast type anodised, complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor with 150mm long cover plate, complete all as specified and directed.

S&F 300mm long brass ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

S&F in repair prelaminated particle board 19mm thick interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screw to timber frame work, complete all as specified and directed.

S&F continuous(piano) hinges, brass, bright finish or electro galvanised 40mm width of flap, complete all as specified and directed.

S&F 6mm thick cover fillets of standard hard board, 40mm wide, and fixing with screws, complete all as specified and directed.

M&L for preparing new wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width or aperture 1.40mm and fixed with stainless steel wire staple, complete all as specified and directed.

M&L for mild steel framed work such as grill, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barrel iron doors, ladders framed balusters, walks railings, frame work of water tanks and similar work conforming to E-165 (Fe-290) including two coats of synthetic enamel paint over one coat of red oxide, complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer, complete all as specified and directed.

S&F aluminium powder coated fancy type brackets suitable for 32mm dia drapery rod, fixed at both ends of openings, complete all as specified and directed

Taking out old damaged tarfelt or membran of any description including screed bed or bedding layer and removing of debris to a distance exc. 250m and n. exc. 500m and cleaning roof surfaces to remove all loose dust etc., roughening surfaces of old concrete roof by picking, sweeping clean and washing down with water using wire brush, brooming down and applying the following treatment all as directed in order of precedence as stated: (a) Brushing neat cement slury with 3.5 kg of cement per Sqm. (b) 15mm thick screed bed or bedding layer in CM (1:4) with water proofing compound as per manufacturer instruction on existing roof surface true to level. (c) Applying one coat of bituminous primer @ 0.40 Ltr/Sqm. (d) Supply and laying 3mm thick APP based polymeric membrane of approved manufactured with weight not less than 4 Kgs per Sqm reinforced with non-woven polyester fabric weighing not less than 160gms per Sqm having softening point not less than 15°C, having tensile strength of 650 N/Sqcm and 350 N/Sqcm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180 N by torch application. Polymeric membrane shall be taken to a height of 30cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (e) Applying one coat of aluminium paint @ 0.15 Kg/Sgm over APP membrane surface. Note:- (i) Laying APP based polymeric membrane shall be done torch on method as per manufactures instructions. (ii) A minimum overlap of 100mm and 75mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturers instruction. (iii) APP based polymeric membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given in IS 16540-2017/1S 16532 2017. (iv) Contractor shall produce necessary test certificate of the manufacturer to the Engr-in-Charge before incorporation in the work. (v) Necessary independent tests shall also be carried out by the contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work. (vi) WPC shall be measured and paid separately as supply only. (vii) The work shall be executed through authorised applicators of original manufacturer only.

M& L for chequered cement concrete tiles 20cm x 20cm x 25mm thick with grey pigment cement and pigment, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M & L for preparation old decorated surfaces of wall and applying one coat of water based acrylic weather proof exterior emulsion paint of approved colour and shade, complete all as specified and directed.

Cutting of exixting MS chequrede plate, 5 mm thick, embeded in cement concrete, using necessary cutting tools, remaning the plate from site of work, cleaning the surfaces, complete all as specified and directed.

Dismantling carefully cracked rigid surface of pavement/hard standing/Taxi Track/patches etc by using mechanical cutter like diamond cutter, (average depth 15mm), sweeping, cleaning with compressed air blower, removal of all loos particles upto a distance exc. 250m & n. exc. 500m, complete all as specified and directed.

M&L for cement concrete work in pavement/hard-standing of flexural strength 40 kg/Sqcm in field using 400 kg of cement per cubic metre, thickness of concrete 25cm or less, complete all as specified and directed.

S&F for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, confirming to Fe 290 (Gde E-165) ,complete all as specified and as directed.

Taking down carefully copper/aluminium point wiring complete (light,fan, plug point & power complete alongwith fittings (switches, ceiling roses, tube light fittings, bulk head fitting, regulator, sockets main switches, DB removing materials to store & making good of disturb surfaces of wall/floors etc, complete all as specified and directed.

M & L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 1.5 Sqmm (nominal area) FRLSH type multi stranded copper conductor, single core drawn in and including concealed, rigid PVC conduit (ISI marked) not less than 20mm dia, medium grade, including all conduit accessories with and including concealed modular box of suitable size for mounting modular switch, sockets, fan regulator etc including 1.5 Sqmm FRLSH type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site & including chases cutting & making good disturbed surface & applying finishes to match existing surface etc. for one light/fan point controlled by one, one way switch single pole, complete all as specified and directed. Note: - (i) Rate quoted shall deemed to be included for cost of modular box (as per number of module of outer cover) and concealed in wall including cutting and sinking of boxes and making good to the walls. (ii) Provision of blank plates as per site requirement shall deemed to be included in the quoted unit rate.

All as per item No 93.00 here-in before but for 3 pin 5 Amp socket point on same board, complete all as specified and directed.

All as per item No 93.00 here-in before but for 3 pin 5 Amp socket point on independent board, complete all as specified and directed.

All as per item No 93.00 here-in before but 2 way point wiring with cable size1.5 Sqmm (for staircase light), complete all as specified and directed.

All as per ser item No. 93.00 here-in before but for one bell/buzzer point controlled by one push button on the same board with other switches or independent, complete all as specified and directed.

All as per item No 93.00 here-in before but with 4.0 Sqmm PVC insulated unsheathed multi stranded cable FRLSH type for one 15 Amp 3 pin socket outlet point including PVC insulated 4.0 Sqmm FRLSH type copper multi stranded conductor as earth wire including steel box of required for modular switches/sockets for 3 pin socket outlet point, 15 Amp on independent board and industrial socket for geyser, complete all as specified and directed.

S&F switch, modular type, single pole, one way, 5/6 Amp, one module, complete all as specified and directed.

S&F switch, modular type, single pole, one way, 15/16 Amps, one module, complete all as specified and directed.

S&F socket outlet, modular type, multipurpose, having provision for 2/3 pin, 5/6 Amp, combined, two module, complete all as specified and directed.

S&F socket outlet, modular type, multipurpose having provision for 3 pin, 15/16 Amp and 3 pin 5/6 Amp, combined, two module, complete all as specified and directed.

S&F bell push, modular type, single pole, 5/6 Amp, one module, complete all as specified and directed.

S&F switch modular type, single pole, 2 way, 5/6 Amp, one module, complete all as specified and directed.

S&F decorative modular cover plate with frame, 2 module, white, completes all as specified and directed.

S&F decorative modular cover plate with frame, 3 module, white, completes all as specified and directed.

S&F decorative modular cover plate with frame, 4 module, white, completes all as specified and directed.

S&F decorative modular cover plate with frame, 8 module, white, completes all as specified and directed.

S&F in repair of bell, ding dong type, AC, 230 volts, single phase complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE Five star rated with brushless direct current motor (BLDC) including electronic modular type regulator (2 module), including taking down of unserviceable ceiling fan and deposited to AGE E/M store yard, completes all as specified and directed.

S&F exhaust fan, steel body, AC, single phase, 230V of size 300mm sweep with, blades, and frame and louvers including cutting wall for fixing exahaust fan and making good the opening in CM (1:3) or PCC (1:2:4) type B1 as required at site, completes all as specified and directed.

S&F ceiling rose of size 65 x 50mm surface bakelite, three phase, polycarbonate, isolated body, complete all as specified and directed.

S&F in replacement decorative, wall mounting, brushed nickel finish fixture with acrylic diffuser suitable with 9 W LED lamp in each lantern B22 base fittings, including one 9W/ 10W LED lamp complete all as specified and directed.

S&F in repair LED light fitting, mirror type with high output diffuser 2 feet, 10 watt 220 V, AC, decorative type with driver, LED tube light of 10 watt connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, completes all as specified and directed.

S&F in repair LED lights fitting 1 x 20 W, 220V, AC , box type with driver, LED lighting fixture with extruded aluminium channel, including LED tube light connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F electric water heater, stoarage type,vartical mounted rust proof ABS outer body with high quality steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc. including PVC connection pipe for hot/cold water to existing water lines, necessary fixing arrangement by using 50 x 5mm MS plate/in built fixing arrangement as per OEM and writing MES No., complete all as specified and as directed.

S&F MCB distribution board (DB) TPN with sheet metal encloser, double door, IP 43 protection, 240 volts, 04 way, with 100 Amps rated copper busbar for each phase (as per OEM) IP 43 protection, neutral link for fixing MCBs/Isolators including taking down old unserviceable MCB DB of any description, completes all as specified and directed.

S&F MCB distribution board (DB), SPN with sheet metal encloser, double door, IP 43 protection, 240 volts, 12 way, with 100 Amps rated copper busbar (as per OEM) IP 43 protection, neutral link for fixing MCBs/Isolators including taking down old unserviceable MCB DB of any description, completes all as specified and directed.

S&F MCB SP 6 to 32 Amps, 240V, 10 KA, 'B' curve, including connection and testing, completes all as specified and directed.

S&F MCB SPN 6 to 32 Amps, 10 KA, 'C' curve, including connection and testing, complete all as specified and directed.

S&F MCB 4 pole, 63 Amps, 10 KA, 'C' curve, including connection and testing, complete all as specified and directed.

S&F power unit suitable for load max up to 3.5 KW including sockets 25 Amps, and four module box for mounting of power unit and power socket, complete as specified and directed.

Taking down old unserviceable submain wiring of any cross section and removing from site, complete all as specified and directed.

S&F MS box (meter box) of size 600 x 200 x 1000mm (double door) 2.0mm thickness, dust proof with front opening hinged door both side, made out of 2mm thick MS sheet cubical type with powder coated painting for mounting of, electric meter etc inside the box fixed in wall by necessary cutting of wall of suitable size in concealed and making good the surface, by applying cement work, brick work and matching colour (Oil bond distemper) etc including dismantling of MS box, electric meters and fixing the new electric meters in new box carefully including necessary electric connection by suitable size of copper conductor cable of suitable length and testing, complete all as specified and directed. Note : (a) Any plastering work involved while taking out old existing meter and refixing the new meter box is deem to be included in this rate. (b) PVC flexible conduit required within the meter boxes is deem to be included in this item rates.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground vertically to a depth not less than 2.25 meter below ground level with top edge of earth plate at a depth not less than 1.5 meter below ground level, earth plate surrounded by 15cm thick packed layer of charcoal dust and common salt, connected to galvanized earth lead wire 4mm thick dia by means of bolts, nuts and washers of galvanized iron or steel and thimbles and other end of the earth wire connected to earthing test point/equipment and protected by galvanized iron pipe light grade 20mm bore, up to earthing test point/equipment fixed with required number of mild steel clamp made out of 25mm x 3mm flat iron and perforated water pipe 20mm dia. GI medium grade of length 2.25 meter and top with socket & plug and bottom connected to earth plate by slit and two bolts/nuts/washers, PCC chamber in PCC (1:2:4) type B-1 and 40mm thick pre-cast RCC (1:2:4) type B-0 cover reinforcement with 40mm x 40mm x 6mm MS angle iron frame of size 25mm x 25mm, excavation & earth work complete all as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009, complete all as specified and directed.

S&F LED flood light fitting 70 Watt 230 volt, AC outdoor type with thermal management in multiple optics with impact and corrosion resistant complete with driver and lamp, IP 65/66 protection, alongwith fixing accessories, complete all as specified and directed.

Taking down single phase electric energy meter any type and refixing, after necessary repair work, complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide and not exc 1.5 metre in depth for foundation, or cable trenches etc. n. exc. 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in incl spreading, leveling watering and well ramming in layers not exceeding 25cm in soft/loose soil, complete all as specified and directed.

Removing of excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point in any type of soil, complete all as specified and directed.

Supply and laying double walled corrugated (DWC) HDPE duct pipe of 40mm dia (outer) conforming to IS, approved colour complete with fittings for cable protection, complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm 4 core, complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm 3.5 core including taking out old unserviceable UG cable of any type and size, complete all as specified and directed.

S&F switch socket combination, 5 pin, 5/6 Amp flush type, complete all as specified and directed.

S&F switch socket combination, 6 pin, 15/16 Amp, flush type, complete all as specified and directed.

Supply, fabricating, installing, testing and commissioning of outdoor type LT bus bar box, factory made, of size not less than 900mm (L) x 900mm (B) x 450mm (D) factory fabricated, cubical panel, floor mounted double door, dust and vermin proof CPRI approved made out of 3.15 mm thick CRCA sheet mounted on 40 x 40 x 5mm angle iron supports at the base duly painted with synthetic enamel paint (spray painting) over and including priming coat and panel board with front and back opening and locking arrangement compete including finishing with two coats of powder coated paint of approved shade over one coat of red oxide zinc chrome primer including all busbar of copper strip 40mm x 10mm for three phase 4 wire 415 Volts, 50 Hz, AC supply, including suitable size cable glands, lugs etc, in proper arrangement for ventilation, complete all as specified and directed

S&F MCCB 63 Amps, AC, 4 pole, 415 Volt, Ics=100%Icu, 25 KA breaking capacity as per IS/IEC 60947-2 with thermal magnetic release including providing new thimble / lugs of suitable size, complete all as specified and directed.

S&F voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with ooutput voltage stabilizied at 230 V with accuaracy of + 2.5% can operate upto 12 Amp and above capacity 15 Ampof capacity upto 5 KVA including replacement of driving transformer input 160 to 280 Volts and output 240 volts (+ 1%) and automatic change over circuit etc, complete all as specified and directed.

S&F single pole and neutral sheet metal enclosure with a two pin and earth plug and socket including one single pole MCB 20 Amp, concealed in wall, complete all as specified and directed.

M&L for earthing of equipment at power house/Sub Stn/DB complete with copper earth plate electrode 60 × 60cm × 3.00mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to existing earth lead strip by means of bolts, nuts, check nuts and washers of brass or HS steel in any type of soil, connected to earthing test point and and necessary excavation and earth work, PCC (1:2:6) type C-1 as earth pit with pre-cast RCC (1:2:4) type B-1 cover slab size 400 x 400 x 50mm reinforced with 8mm dia TMT bar, 100mm c/c both ways including one handle made of 12mm dia including providing charcoal or coke and common salt in alternate layer of 15cm compacted thickness all around the earth electrode with funnel and 20mm bore galvanized iron watering pipe (light grade) wire mesh, copper lugs, complete in all respect,including Copper earth strip 20 x 3.00mm, protected by 40mm bore (medium grade) galvanized iron pipe up to earthing test point including disposal of soil to a distance not exc 50 mtr and necessary testing on completion including taking out/dismantling of old unserviceable earthing, complete all as specified and directed. Note:- Proper earthing pit should be provided with pit cover.

Note: An amount of Rs. 51,226.00 on account of Credit Schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

M/S BIJAY KUMAR SHIVA (BID ID -3513166)

BHARAT ELECTRIC (BID ID -3514698)

CONSTRUCTION SHELTER (BID ID -3513789)

M/S ROY ENTERPRISE (BID ID -3514704)

SHRI D P AGARWAL (BID ID -3513412)

M/S RATHIN ENTERPRISES (BID ID -3513793)

M/S. KUMAR CONSTRUCTION CO. (BID ID -3514471)