Renovation and up gradation of Utsav Hall at CSIR CIMAP Lucknow

Amount

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

. Hot finished welded type tubes. (New work)

Labour charges for Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Dismantelled old sections to be used (Old sections to be provided by the department free of cost)

Providing and laying catpet weight not less than 500 gm / sqm, 1800 mm wide over 12 mm thick heavy density foam including cleaning of floor and fixing with adhessive, the joint of carpet to be sealed with adhessive/ tape to match the colour of carpet complete as per direction of Engineer - in - charge. Carpet weight not less than 500 gm/ sqm over 12 mm thick heavy density foam.

Labour charges for fixing calcium silicate old existing ceiling tiles with suitable nicle coated MS Holding clips for gripping ceiling tiles etc. complete. Old ceiling tiles to be provided by department free of cost. (Labour charges for frame work to be paid seperatately). Labour charges for fixing Calcium silicate false ceiling tiles including cost of Nicle coated MS holding clips heavy duty.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: Royl shine of Asian paint or equivalent One or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface "Apex Ultima" or equivalent.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: G.S. Sheet

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Labour charges for fixing old anodised/powder coated aluminium work consisting of tee/ angle sections, of approved make in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 4 mm dia. all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). Old aluminium Tee, Angles and sections shall be provided by the department free of cost.

Labour charges for fixing 4 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof purlin/truss including cost of S.S Butter fly of heavy duty complete as per direction of Engineer-in-charge.

Supplying and installation padded seat and back Plastic moulded chair with arms Supreme ornate or equivalent of required colour and shade as approved by Engineer - in - charge complete.

M/S AVADH TRADERS

H S ENGINEERS

harpal singh