Danish Fort Tharangambadi - Electrical

Amount

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module GI switch box on wall with 6A one way module switch with module front plate with Continuous earth wire connection of 14 SWG TC wire with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 4 Points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module GI switch box on wall with 6A one way module switch with module front plate with continuous earth wire connection of 14 SWG TC wire with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC Rigid pipe on wall and ceiling with PVC accessories with suitable Module GI switch box on wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with painting of Suitable colour with continuous earth wire connection of 14 SWG TC wire for Open PVC conduit Plug point ( 8 points / Coil) Higher End.

Supply and fixing of Decorative Chandelier light fitting (Make: Philips/Equ.) with 5 Nos. 4W Filament LED Bulb Light Warm White/2700K (Make: Philips/Equ.) with mouting screws and brackets and suspenstion from the ceiling with PVC unseathed copper leads from terminals to the fitting.

Supply and fixing of Surface Mount Down Light with 26.9W LED Warm White IP-23, 3000K Lamp (Make: LEDS C4/Equ.) with all mounting accessories with PVC Unsheathed copper leads from terminals to the fitting.

Supply and fixing of Decorative Wall Light Fitting (Make: Philips/Equ.) with 8W Filament LED Bulb Light Warm White/2700K (Make: Philips/Equ.) with accessories for Mounting on Wall.

Supply and fixing of Inground luminaires up pathways with 17.6W LED light (Warm White 3000K) IP65 ingress protection made up of Stainless Steel Aluminium Structure and Toughened Glass Diffuser (Make: LEDS C4/Equ.).

Supply and fixing of Architectural Tracks Spot Light Fitting with 10W LED Light (IP 23, Warm White 3000K) with mounting Screws and Brackets with PVC Unsheathed copper leads from terminals to the fitting. (Make: LEDS C4/Equ.)

Supply and fixing of Linear Profile Light LED light with 19.2W/Mtr LED Strip Warm White 3000K IP 20 Protection (Make: LEDS C4/Equ.) with PVC Unsheathed copper leads from terminals to the fitting.

Supply and fixing of Corner Linear Profile Light LED light with 19.2W/Mtr LED Strip Warm White 3000K IP 20 Protection (Make: LEDS C4/Equ.) with PVC Unsheathed copper leads from terminals to the fitting.

Supply and fixing of Cabinet Light with 2.2W LED Light (IP 66, Warm White 3000K) with mounting Screws and Brackets with PVC Unsheathed copper leads from terminals to the fitting. (Make: LEDS C4/Equ.)

Supply and fixing of Spot LED Light with 12W/Mtr LED Lamp, IP-66 Protection, 3000K with all mounting accessories with PVC Unsheathed copper leads from terminals to the fitting.

Supply and fixing of Spot light with 6.4W LED Warm White IP-54, 3000K Lamp (Make: LEDS C4/Equ.) with all mounting accessories with PVC Unsheathed copper leads from terminals to the fitting.

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting.

Supply and fixing of specially Heavy type water poof, Dust proof integral luminaries fitting provided with 1×150 Watts LED High Lumen Flood Light fitting (Crompton / Philips make or Equivalent) with control switch gears, Alglas coated reflectors, with cable connection etc: complete as per standard specification

Supply and fixing of 500mm Pedestal Type Fan with Stand mount with Adjustable Height and Swing.(Make: Havells/Equ.).

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End.

Supply and fixing of 3 nos.6A two module 5 pin socket , 3 nos. 6A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End.

Supply and fixing of 20Amps DP Plug and Socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) [Legrand (MDS) / Hager (L&T) make].

Supply and fixing 4-Way SP MCB DB with metal door cover with IP-42 protection with busbar and neutral link with 1 No 32A DP MCB as incoming and 2 Nos 6/10A SPMCB as outgoing in flush with wall and making good of the concealed portion with earth connection only.(Make:Legrand(MDS)/Hager(L&T)/Equivalent)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End.

Supply and fixing of 3 phase 4-Way Horizontal type double door with IP-42 protection (MDS/ Legrand/ L&T make/ equivalent) with busbars and neutral links with 1 No 40A 4-Pole MCB as incoming and 12 Nos 10/32A SPMCB as outgoing in flush with wall and making good of the concealed portion with earth connection only. (Make:Legrand (MDS) /Hager(L&T)/ Equivalent)

Supply and fixing of 3 phase 8-Way vertical type double door with IP-42 protection (MDS/ Legrand/ L&T make/ equivalent) in sheet steel enclosure with busbars and neutral links with 1 No 100A 4-Pole MCB & 63A 4P RCCB/ELCB as incoming and 6 Nos 32A TP MCB & 6 Nos 20/32A SPMCB as outgoing in flush with wall and making good of the concealed portion with earth connection only. (The MCBDB and MCB's should be of Higher End)

Supply and fixing of 100 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and fixing of 100A TPN Sheet Double Break with HRC fuse and Neutral on suitable angle iorn frame work with earth connection only.

Supply and fixng of TNEB meter board suitable for 3 phase 100A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall coveredwithhylem sheet of size 2 feet x 1-1/2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 100A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete

Supply, Erection, testing and commissioning of dust and vermin proof outdoor metering box of suitable size made up of 16 SWG CRCA sheet steel for Outter Body and Doors to accomodate 100A EB Meter Board and 100A TPN Main Switch with Painting with two coats of high quality epoxy paint over one coat of red oxide primer.

Supply and Erection of Testing and Commissioning of UPS unit of Capacity 1KVA with input voltage of 230Volt 1-Phase AC Supply for 50Hz and output voltage 230Volt 1-Phase AC Supply for 50Hz , Pure Sine Wave with the following accessories circuit and 60Mins Backup at full load with UPS Stand Arrangements. 1) Battery Charging Devices 2) Inverter Circuits with Isolation Transformer 3) Overload as well as Short Circuit, Short Circuit Tripping Device 4) Indication LED is for all operation like Battery Etc., 5) Reset switch 6) Batteries: SMF Make Exide Express/ SF Sonic or Equivalent (For UPS Power Supply)

Supply, testing, commissioning and handing over of 1 No. 20 KVA Diesel generator set of 0.8 PF three phase 415/420 V 50 Hz, 1500 RPM CPCB Approved capacity compressing of Engine (Kirloskar/ Equ) developing 27BHP water cooled clock wise rotating feed pump with 16KW/20KVA operating capacity brushless alternator close coupled underneath fuel tank standard safeties LLOP with stop solenoid battery with lead Electric start and vibration fitting and acessories and Standard Panel as detailed below including transporting and unloading charges. (A) ENGINE Water cooled diesel engine suitable for generating application with a shaft output of 27BHP at 1500 RPM under NTP conditions.The engine shall comprise the following standard fittings.Flexiblecoupling,Flywheel,aircleaner,Fanblower,Radiator water pump, fuel pump, fuel filter lubricating oil filter etc. (B)12V Electronic starting Equipment. Complete with starter motor dynamo standard batteries with cable flexible exhaust piping of 50 cms length.

(C) ENGINE INSTRUMENT PANEL/ MOUNTED Starting push button/starting key lubricating oil temperature gauge lubricating oil pressure gauge water temperature guage safety control for low lubricating oil pressure, safety control for high water temperature safety control for over speed hour meter(Mechanical) and RPM indicator battery charging ammeter. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous at full load. (D) ALTERNATOR 20KVA/16KW capacity of brushless alternator AC 3 phase 50 c/s. 415/420 Volts, 0.8 PF 1500 RPM under NTP conditions confirming to IS 13364 (Part II) 1992 to be means of coupling. (E) STANDARD CONTROL PANEL The STANDARD Control panel (Cubicle) should be fabricated with vermin proof and dust proof best quality sheet steel and floor mounted with removable rear panels and hinged front foors with enamel painted and incorporating the following with suitable provision for connecting incoming and outgoing leads have been made on the control panel.

(F) BASE FRAME: The base frame should be fabricated MS channel frame of rigidly welded construction for mounting of generator set. The engine and alternator should be coupled by suitably designed diaphragm type flexible coupling with guard and mounted on the base frame with proper alignment. (G) ACCOUSTIC ENCLOSURE: Specially designed to meet stringent MoEF/ CPCB norms of 75 dBA @ 1mtr at 75% load under free field conditions. ƒ The acoustic enclosure is made of CRCA sheets in Munsel green shade and a structural/ sheet metal base frame painted in black. ƒƒ High quality noise absorbant and fre-retardant grade acoustic insulation material (Rockwool) complying to IS 8183. (1) Supply of manuals for operation & maintenance of DG set with warranty card etc. (SR) (H) Fuel Tank 43Ltrs. Removable Fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet an outlet connections and mechanical fuel gauge. Fuel tank can be easily removed for cleaning or any maintenance. (I) Battery 1No 12V 88AH battery (Kirloskar/Ashok Leyland make)

30) 1No. Earth fault relay 31) Isolator to isolate the neutral Note: 1. The control panel should be complete with necessary fuses, cables label other accessories and with neutral isolation arrangements. 2. The engine should trip for the following a. Low lubricating oil pressure b. High water temperature c. Overspeed (F) BASE FRAME: The base frame should be fabricated MS channel frame of rigidly welded construction for mounting of generator set. The engine and alternator should be coupled by suitably designed diaphragm type flexible coupling with guard and mounted on the base frame with proper alignment. (G) ACCOUSTIC ENCLOSURE: Specially designed to meet stringent MoEF/ CPCB norms of 75 dBA @ 1mtr at 75% load under free field conditions. ƒ The acoustic enclosure is made of CRCA sheets in Munsel green shade and a structural/ sheet metal base frame painted in black. ƒƒ High quality noise absorbant and fre-retardant grade acoustic insulation material (Rockwool) complying to IS 8183. (1) Supply of manuals for operation & maintenance of DG set with warranty card etc. (SR)

(H) Fuel Tank 43Ltrs. Removable Fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet an outlet connections and mechanical fuel gauge. Fuel tank can be easily removed for cleaning or any maintenance. (I) Battery 1No 12V 88AH battery (Kirloskar/Ashok Leyland make)

Supply and installation of exhaust piping with Silencer of sufficient length with suitable MS pipe so as to extend outside the generator with necessary thermal insulation .

Providing fuel oil to run the set for 8 hours on load testing and commissioning using water rheostat or suitable leading element.First charging of fuel oil to full capacity and first charging of battery while handing over to dept.

Supply of tools such as 1no. 15” cutting pliers, 1no. 6” screw driver, 2nos. 9” screw drives, 1set of 6nos, double ended spanners, 1no. Adjustable spanner, 1no. ½ Ib hammer, 1no. Spanner for removing engine oil plug, 1no. Line tester required for the maintenance and operation of the generator set -1set.

Supply and demonstration of the following safety accessories: a) one set of 4 nos. fire buckets made out of 40 x 40x60 mm MS angle b) first aid box with medicine complete with all first aid medicines c) Danger Board as required by the Electrical Autorities d)Fire extinguishers Co2, 4.5 Kg confirming to TAC Norms e)First Aid Chart Tamil & English

Supply and run of 2 of 4sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14SWG TC wire with painting of suitable colour.

Supply and run of 2 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour.

Supply and run of 4 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth Wire connection of 14 SWG TC wire with painting of suitable colour

Supply and Run of 4 of 16 sq.mm. (101/0.45) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigd pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour.

Supply and laying 3½ X 25 sq.mm PVC Armoured LTUG Cable a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and clamping of 3½ X 25 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3½ X 25 sq.mm PVC Armoured LTUG Cable with earth connection.

Supply and providing cable end termination of 3½ X 25 sq.mm PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Earthing as per P.W.D standard with an earth electrode of 2 Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection.

T PAULKANNU & CO (BID ID -1078091)

KARTHIKEYAN ELECTRICALS (BID ID -1078356)