REPAIR TO CERTAIN ROAD PATHS KERB STONE ROAD FURNITURE IN THE AREA OF PALAM UNDER GE (P) AF GURGAON

Amount

M&L for Repair to potholes any depth, not exc 1 sq m each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal) making good by applying tack coat with VG-10 paving bitumen @ 5Kg per 10 Sqm, putting in screened & graded road metal and rolled with vibromix road roller, watering and well ramming (including supply of road metal), complete all as specified and directed.

M&L for preparing Old Black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with mechanical brooms and remove all loose dust etc. with air compressor and applying evenly a priming/tack coat with paving bitumen VG-10 @ 5Kg per 10 Sqm complete all as specified and directed .

M&L for 30mm Consolidated thick semi dense asphaltic concrete with @5.50 % Paving bitumen (VG-30) Gde by weight of total mix of Asphaltic Concrete, rolled and compacted to required camber and gradient, mixing is carried out in mechanical hot mix plant and laying, spreading and rolling with 8 to 10 tonne power vibromax/Tandom road roller to required level, gradient, camber and super elevation, complete all as specified and directed. Note : (1) The work shall be Strictly carried out by using mechanical/Sensor paver only. (2) Work will be allowed only after approval of Semi Dense Asphaltic Concrete Design Mix (3) Contractor Should arrange Bitumen extraction Test at Site during execution of SDAC work. Note: The actual requirement of binder shall be as per the job mix design and the tests specified. The contractor shall submits the job mix design from Govt Approved Lab for approval from GE and the rate shall be inclusive of the same. However quantity of bitumen from the mix design found more than specified 5.5% same shall be provided with no extra cost to the Govt. In case binder content found to be less than 5.5% as per mix design as specified in Schedule "A" shall be adjusted @ the rate of 45.00 (Rs Forty Five) / kg for the less quantity of bitumen used. The quantity of 5.5% mentioned is exclusive of any wastage and no wastage shall be taken into account for the purpose of above adjustment)

M&L for painting lines, dashes, arrows, letters etc on roads pavement by using reflective thermo plastic paint confirming to BS:3262 (5Kg/Sqm) with glass beads potters (250 gms) in 10 cm/15 cm wide strips on bituminous road surface and road marking (by Hot Mechanical process with Road Marking Machine) including complete removal of dust particle by wire brushes or sweeping with brooms complete all as specified and as directed.

Demolition of stone slab and tiles laid dry and pointed of any description or thickness in floors. Aprons, etc, complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block glossy finish, any shape & size with grey cement & pigment conforming to IS 15658-2006 of 60 mm thickness M-35 grade over 25mm thick sand cushioning, complete all as specified and as directed .( note : sand cushioning measured and paid separately). Note:- The contractor shall submit manufacturer test certificate during sample approval.

M&L for Sand filling under floors or in foundation including watering and consolidation complete all as specified and as directed.

M&L in repair for Chequered Cement Concrete Tiles 300X300X 25mm thick pre printed colour, Set and Jointed in Neat Cement Slurry with Grey Cement and Pigment over and including Screed Bed 20mm thick in Cement Mortar (1:6) as in Path, complete all as specified and as directed. Note:- The contractor shall submit manufacturer test certificate during sample approval.

Demolition of brick masonry work, built in cement mortar of any description including rubbish of the premises complete all as specified and directed .

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in CM 1:4 including raking out joints complete all as specified and directed.

Taking down Cement Plaster from wall of any description from Brick/concrete surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not specifically provided complete all as specified and as directed.

Demolition of Cement Concrete (un-reinforced) of any description, not exc. 150mm thickness (above or below Ground Level) and removing the same from Site(s), complete all as specified and as directed.

M&L for PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in Coping, Benching, Kerbs, Coving etc complete all as specified and as directed.

M&L for RCC Nominal mix concrete type B1 (1:2:4) using 20mm graded stone aggregate as in slab supported on walls and the like complete all as specified and as directed.

M&L for TMT bars 08 mm dia and over in dia, cut to length bent to shape required including cranking, bending, hooking ends and binding with MS wire (annealed) not less than 0.9mm dia as in main distribution bar complete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L for 10 mm thick cement plaster by using manufacture sand in CM 1:4 on brick/concrete surfaces and parapet, including finishing even and smooth without using extra cement complete all as specified and as directed.

M&L for dismantling of old PCC Kerb Stone of any description and Providing and Fixing New Ready made PCC (1:2:4) Type B1 Kerb Stone of Size 600x150x300mm with Rounded edge fixed in position and pointed in CM 1:4 and finishing exposed surface even and smooth complete all as specified and as directed.

M&L for preparation for newly plastered surface of wall and applying two coat of cement base paint over a coat of primer on walls complete all as specified and as directed.

S & F in repair reflective road studs of size 100X120x20mm (minimum weight 130 gms most effective night guidance even under the most adverse weather condition Top quality dynamically designed studs having excellent quality standards ,can bear load upto 25 tonnes. The studs are visible and can also be hard and flat, due to the rumble when a vehical crosses over them, road studs in different colour to delineate both the carriage way at the center and at the edges of roads made out of in rigid ABS plastic. The special impacts, specific reflective panel of studs provides very night reflectively incl epoxy for fixing in position allas specified and as directed . Make : Road star/sinor/STC/3M/Suneyez/Darkeye

S & F in repair solar studs of size 125X125X25 mm made from aluminium alloy and construction solar powered by nanocrystal solar panel type with rechargable battery minimum 2.5V , 500MAH, LED both sides (3 each side) display colour red. Visual distance approx 800 mtr in working temperature (10 degree to 70 degree centrigrade) with starting intensity 300 Lux to 600 Lux . Minimum approx weight 900 gms , water resistance made up high compressive material can sustain over 10 tonnes with one year replacement warranty incl epoxy for fixing in position complete all as specified and as directed . Note:-(i) Appropriate epoxy adhesive on the road surface shall be provided as per manufacturers specifiaction before fixing the cat eye and the same is includued in quoted rate by the contractor Make :Road Star/Sinor/STC/Kohinoor /3M/ Suneyez/Dark eye

S&F sign board made out of 3mm thick ACP (Aluminium composite panel sheet) fixing on stainless steel pipe . Writing English/Hindi Radium/Reflective letters n less than 20Cm height with Air force monogram, lvory blue base background and white computerised letter reflective on retro reflective sheet high quality including taking down existing board complete all as specified and as directed.

S&F in repairs polished pipe SS-304 grade any size/tube cutting and gas welding electro gas welding fixing around board and standard bright polishing including removing old post and fixing New board in Ground with PCC 1:3:6 Type C2(Using 20mm graded stone aggregate) block of Size 300x300x300mm in each post complete all as specified and as directed.

S&F for Speed Bump made from heavy duty ABS with high resistance wear and tear property. UV stablized black & yellow combination. High reflective reflectors having L=700mm, W=230mm available in both shades in red and yellow colour. Speed Bump duly filled with concrete mixer for better stability. Bumps should be fixed on road with dual method i.e. applying thick coat of epoxy chemical on road as well as bumps also. Finally fixing nails in epoxy applied speed bump for best durability, complete all as specified and directed . Make : Road Star/Sinor/STC/Kohinoor/3M/Suneyes /Dark eye

S&F in repairs solar delineator 750mm high fixed in PCC Block of size 300x300x300mm in cement concrete 1:2:4 type B-1 using 20mm stone graded aggregate, and red blinker and charged by solar energy having 1" red colour high intensity reflective tape rounded duly pasted on lower side of lamp fitted on PVC deluxe quality pipe of 50mm dia, complete all as specified and directed. Make : Road Star/Sinor/STC/Kohinoor/3M/Suneyes /Dark eye

Schedule of Credit

S. Kumar & Company

PAWAN KUMAR

Parveen Builders

PBS Construction Co

R K GOEL ABHEY KUMAR JAIN