SPECIAL REPAIRS TO NORTHERN ANNEXE AT AF STN CHANDIGARH

Amount

BOQ REVISED ON 21 DEC 2022

Taking down cement plaster from brick walls, ceilings and concrete surfaces of any description including raking out joints, hacking for key, scrubbing down with water etc. and removal of rubbish outside MoD land complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on brick/ concrete surface of walls finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick plaster in cement mortar (1:3) on concrete surfaces as on ceiling finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15mm thick plaster in cement mortar (1:4) mixed with water proofing compound on brick wall/ concrete surface finished even and fair without using extra cement, complete all as specified and directed. Note: Supply only of water proofing compound shall be measured and paid for separately.

M&L for preparation of newly plastered surface of walls and applying two coats of oil emulsion distemper over a coat of primer using alkali resistant priming paint complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of cement base paint complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for complete removal to existing treatment from walls and applying two coats of distemper oil emulsion over a coat of chalk whitening preparatory to distempering complete all as specified and as directed.

M&L for complete removal to existing treatment from walls and applying two coats of cement base paint complete all as specified and as directed.

M&L for complete removal to existing treatment from ceiling surface and applying two coats of white wash complete all as specified and as directed.

M&L for complete removal to existing treatment from walls and applying two or more coats of Premium acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (Camouflage pattern) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

Taking down chowkhats or frames (any type) n. exc. 1.5 Sqm each without taking off shutters from frame and removing from site complete all as specified and directed

Taking down chowkhats or frames (any type) exc. 1.5 Sqm but n. exc. 4.0 Sqm each without taking off shutters from frame and removing from site, complete all as specified and directed

M&L cutting holes in brick walls built in cement mortar for inserting hold fasts; depth of embedded portion of hold fasts or lugs measured from the face of the jamb into the wall exceeding half brick but not exceeding one brick and making good dismantled portion in cement mortar (1:3) or cement concrete (1:2:4) type B-1 as required including removal of rubbish outside MoD land complete all as specified and directed.

S&F factory made pressed steel frames for doors with two rebates of size 125mm x 60mm made out of 1.25mm thick sheet including necessary fixing lugs, hinges, lock strike plate, etc. duly painted with one shop coat of red oxide primer including back filling of PCC (1:3:6) type C-0 complete all as specified and directed.

S&F factory made solid PVC moulded door shutters with (with wood free EPS) particle board core, 28 to 30mm thick stiles, with 2 raised panel design with 2mm plain moulded PVC prelam on both faces complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube as per specification & drawing in SSR Part-II in opening complete all as specified and directed.

S&F in the frame at site, factory made solid PVC panel door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, as per specification & drawing in SSR Part-II complete all as specified and directed.

S&F factory made box type steel window with pintal hinges & 2 Nos 150mm mild steel tower bolt to each shutter, steel handle without glazing bars including flat iron 12mm x 3mm for securing wire mesh, dovetailed or welded and treated with one shop coat of zinc chromate primer complete all as specified.

S&F factory made, box type steel window with pintal hinges & 2Nos 150mm mild steel tower bolt to each shutter, steel handle and with glazing bars, dovetailed or welded and treated with one shop coat of zinc chromate primer complete all as specified

S&F factory made box type steel section ventilator fixed type with glazing bars, dovetailed or welded and treated with one shop coat of zinc chromate primer complete all as specified.

S&F 4mm thick polycorbornate sheet fixing with and including flat iron of size 30mm x 4mm including welding & self-taping screws etc complete all as specified and directed.

S&F sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads in squares n. exc. 0.5 sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples or fixed to wooden beads complete all as specified and directed.

S&F 100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin anodised, type C-21 complete all as specified and directed,

S&F 200mm aluminium anodised, barrel tower bolts of extruded section all as specified and directed.

S&F 150mm long extruded aluminium alloy handle fabricated type, anodized complete all as specified and directed.

S&F sliding door bolts 250mm long of extruded sections aluminum alloy, anodized with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminum complete all as specified and directed.

S&F 300mm long ordinary rat tail rod pattern MS door springs including roller and roller plate complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillar etc(other than roofs, floor/ paving) and removing demolished material outside to MoD land complete all as specified and directed.

M&L for brick masonry old size sub class 'B' burnt bricks built in cement mortar (1:4) straight or curved on plan to any radius as in half brick thick walls complete all as specified and directed.

M&L for brick work with old size sub class 'B' burnt brick built in cement mortar (1:6) straight or curved on plan exc. 6m mean radius complete all as specified and directed.

M&L for preparation of new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide primer complete all as specified and directed.

M&L for preparation of old treated wooden or wood based surface over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted steel surface over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Hosted and fixed in position, rotational moulded polyethylene triple layer water storage tanks (cylindrical vertical with closed top) white in colour of capacity 500Ltr including inlet pipe and plug, outlet, waste etc complete all as specified and directed.

Hosted and fixed in position, rotational moulded polyethylene triple layer water storage tanks (cylindrical vertical with closed top) white in colour of capacity 1000Ltr including inlet pipe and plug, outlet, waste etc complete all as specified and directed.

Dismantling brick tiles or terracing tiles single layer in roofs pointed in cement mortar, stacking serviceable tiles for re-use and removal off rubbish outside MoD land complete all as specified and directed.

Taking down existing bitumen felt roof treatment including cement mortar bedding and cleaning the surface by wire brushing, sweeping, cleaning, washing down to remove all loose dust etc. and preparing roof surfaces including removal of debries outside the MoD land complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate as in coping, roof padding, roof kerb, mud stops, water trough, benching and like including weathering slightly, rounded or chamfered angle and throating with necessary form work complete all as specified and directed.

M&L 15mm thick cement plaster in cement mortar (1:4) mixed with WPC as per manufacturer's instructions on concrete surfaces as in terracing finished even and smooth without using extra cement after applying neat cement slurry @ 3Kg/ Sqm complete all as specified and directed. Note:- Supply only of water proofing compound will be measured and paid separately.

M&L for cutting grooves in brick/ concrete walls 75mm wide and 65mm deep for inserting APP membrane and shaping horizontal face of groove with cement mortar (1:3) and removing the rubbish off the permises complete all as specified and directed.

M&L for providing water proofing treatment of roof consisting as under complete all as specified and directed:- (a) Applying a coat of bituminous primer conforming to IS-3384:1986 @ 0.30 Ltr/ Sqm. (b) Applying a layer of 3mm thick APP polymer membrane of weight not less than3 Kg/ Sqm reinforced with polyester non wove fabric (wt. not less than 150 Gms/ Sqm) duly sealed at over laps and joint with flame (by torch application) as per manufacturer's instructions complete all as specified and directed.

All as per Srl No. 44.00 above but on vertical surfaces using hot blown bitumen having penetration value of 30/ 40 applied @ 1.20Kg/ Sqm over primer @ of 0.30 Kg/ Sqm complete all as specified and directed.

M&L for laying 40mm thick brick tiles laid on and including 15mm thick screed in cement mortar (1:6) using grey cement and grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement as separate operation laid on concrete roof complete all as specified and directed.

M&L for cutting out cracks to V-section in existing RCC roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry (1:3) complete all as specified and directed.

S&F in repair 20mm dia brass chromium plated tubular towel rail with brackets complete all as specified and directed.

S&F 140mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor complete all as specified and directed.

M&L mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders framed balusters, walk ways, railings and similar work conforming to Fe-290 Grade E-165 quality, complete all as specified and directed.

Welding in repair n. exc. 2.5cm in length, thickness of metal to be welded n. exc. 6mm including cleaning, preparing the surfaces and holding the member in true position for maintenance of steel items such as gates, grills, doors window etc. complete all as specified and directed.

Supply only integral water proofing compound

Dismantling floor, hearth or wall tiling including cement mortar bedding but not hacking, removal serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7mm to 8mm thick (square/ rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18sqm as in floors etc., set & jointed in neat grey cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

S&F first quality glazed designer pattern coloured ceramic tiles of size 450mm x 300mm x 7mm thick fixed in pattern to wall (combination of dark & light colour with border) as in skirting, dado etc., set and jointed in neat cement slurry laid over and including 10mm thick rendering of cement mortar (1:3) and pointing in white cement with pigment to match the shade of tiles complete all as specified.

S&F in repairs PVC polypropylene, valveless syphonic action type low level flushing cistern 10 litre capacity, white/ coloured with inlet, ball valve with float and handle, including new brackets fixed in position, PVC bend/ flush pipe 32mm dia complete including connections to water mains complete all as specified and directed.

S&F in repair, vitreous china counter top (self rimming) wash hand basin, white in colour of size 630mm x 500mm including circular cutting and tucked in granite slab including 15mm dia cast copper alloy chromium plated fancy type single lever basin mixer, 32mm dia brass CP waste fitting and connection to waste pipe and water pipe complete all as specified and as directed. Make: Hindware model RHAPSODY Cat No. 10045 or equivalent in CERA.

M&L 20mm thick Granite (of any type) tiles machine cut, bedding on 15mm thick screed bed in cement mortar (1:4) and jointed, with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

M&L for cutting holes into or through brick wall built in cement mortar exc. 150 Sqcm but n. exc. 400 sqcm and making good in cement mortar (1:3) or cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate complete all as specified and directed.

Use and waste of formwork to sides and soffits of lintels, cantilevers, shelves including supports, overhangs, etc. also splay between floors and beam flat for fair finished surface of concrete complete all as specified and directed.

M&L for RCC (1:1½:3) type A-1 using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, shelves and the like complete all as specified and directed.

M&L for RCC (1:1½:3) type A-1 using 20mm graded stone aggregate with and including Nitozinc primer (FOSROC or equivalent) @ 200ml per Sqm of surface area of concrete as in chajjas, fins, louvers, roof projections, beams and lintel after removing of loose concrete and preparation of roof surface by application of de-rusting chemical such as Dr fixit rust remover or equivalent and welding additional main bars/ distribution bars if found necessary by inserting to adequate depth in beam by drilling, pinning reinforcement old bars/ new with including necessary scaffolding and form work as required upto the height of 3.5 mtr complete all as specified and directed. Note:- Reinforcement will measured and paid separately.

M&L for RCC (1:1½:3) type A-1 using 20mm graded stone aggregate with and including Nitozinc primer (FOSROC or equivalent) @ 200ml per Sqm of surface area of concrete as in chajjas, fins, louvers, roof projections, beam and lintel after removing of loose concrete and preparation of roof surfaces by application of de-rusting chemical such as Dr fixit rust remover or equivalent and welding additional main bars/ distribution bars if found necessary by inserting to adequate depth in beam by drilling, pinning reinforcement old bars/ new at height exceeding 3.5m and upto the height of 7.5m complete all as specified and directed. Notes:- Reinforcement will measured and paid separately.

M&L TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending for hooping of columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips, as in reinforcement complete all as specified and directed.

S&F in repair vitreous china urinal half stall type white including providing fixing plugs, bedding urinals against wall in cement mortar (1:2), securing urinal to plug with and including 60mm long brass screws, pointing around urinal back including provision of PTMT waste coupling half or full threaded suitable for urinals complete all as specified and directed.

S&F PTMT urinal spreader of any colour for fixing with 15mm dia pipe (minimum weight 60gms) all as specified and directed.

S&F in repair 15mm PTMT push cock any colour, suitable for urinals(minimum weight 50gms) complete all as specified and directed.

S&F in repair chromium plated shower rose 125mm in size with or without swivel joint including fixing to steel pipes complete all as specified and directed.

S&F in repair brass chromium plated stop valve fancy type with long shank and cup (concealed type) screwed down high pressure, screwed both ends for 15mm bore iron pipe or unions complete all as specified and directed.

S&F in repair vitreous china wash down water closet squat pan (Orissa pattern/ Indian type) of size 580mm x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe but including CI ‘P’/ ’S’ trap), set and jointed including embedding concrete complete all as specified and directed.

S&F in repair bib taps, cast copper alloy, fancy type with capstan head, chromium plated, screwed down high pressure, screwed for iron pipe or for brass ferrule 15mm dia bore complete all as specified and directed.

M&L cutting chases, pinning in and making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing and making good cutting not exceeding 10cm girth and removal of rubbish outside MOD land complete all as specified and directed.

S&F 15mm bore galvanised iron tube medium grade with all fittings and fixed complete to walls and ceiling or laid in floor including taking up existing tubing complete all as specified and directed.

S&F 20mm bore galvanised iron tube medium grade with all fittings and fixed complete to walls and ceiling or laid in floor including taking up existing tubing complete all as specified and directed.

Dismantling of cast iron work of any description and in any position all as specified and directed.

S&F in repairs cast iron bends, diminishing pieces or tapers 100mm bore complete all as specified and directed.

S&F in repairs 100mm dia bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

M&L cast iron floor trap 75mm dia of outlet with mild steel chromium plated grating including jointing to waste pipe and embedding in PCC (1:2:4) type B-1 fixed in repairs complete all as specified and directed.

M&L cast iron Nahani trap 75mm dia of outlet with mild steel chromium plated grating, excluding jointing to waste pipe in PCC (1:2:4) type B-1 fixed in repairs complete all as specified and directed.

M&L cast iron floor trap 100mm dia of outlet with mild steel chromium plated grating including jointing to waste pipe and embedding in PCC (1:2:4) type B-1 fixed in repairs complete all as specified and directed.

S&F in repairs angle valves, cast copper alloy, screwed down high pressure, fancy type with capstan head, chromium plated, screwed both ends for iron pipe or for unions, or for brass ferrule 15mm dia bore complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450mm all as specified and directed.

Demolition of lime concrete of any description and in any position and removal of rubbish outside of MOD land complete all as specified and directed.

M&L for water proofing treatment to sunken portion of WCs, bath room etc. as under complete all as specified and directed: (a) Applying cement slurry mixed with Acrylic based polymer modified cementious composite compound coating of approved make. (b) Applying 15mm thick plaster in cement mortar (1:4) mixed with integral water proofing compound on floor and wall and finishing the surfaces fair and even. The surface shall than be cured and allowed to dry. (c) First layer of slurry of cement @ 0.5Kg/ sqm. This followed layer will be allowed to air curing for 4 hrs. (d) Second layer of slurry of cement @ 0.242 Kg/ sqm mixed with Acrylic based polymer modified cementious composite compound @ 0.126kg/ sqm. This layer will be allowed to air cure for 4 hrs followed with water curing 48 hrs. Note:-Supply only water proofing compound shall be measured and paid separately.

M&L for PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in floors complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 using 12.5mm graded stone aggregates using integral water proofing compound @ 3% by weight of cement as in padding concrete to sunken floor, coving/ gola at junction of the floor and vertical walls including chamfering on edges complete all as specified and directed. Note:- Supply only waterproofing compound shall be measured and paid separately.

M&L for lime concrete (1:3) using 40mm graded brick aggregate as in mass concrete complete all as specified and directed.

S&F in repair 100mm bore cast iron spun pipes as in soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or floors/ walls complete all as specified and directed.

S&F in repair 75mm bore cast iron spun pipes as in soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or floors/ walls complete all as specified and directed.

S&F in repair PTMT grating doom 125mm dia with waste hole fixed on floor/ Nahani traps with cement mortar (Minimum weight 40 gms) complete all as specified and directed.

S&F in repair PTMT grating doom 100mm dia fixed on floor/ Nahani traps with cement mortar (Minimum weight 25 gms) complete all as specified and directed.

S&F in repair gun-metal globe or gate valves with iron wheel head screwed both ends for 15mm bore iron pipe complete all as specified and directed.

S&F in repair 100mm bore CI socket double collars with oval access door fixed with lead joints complete all as specified and directed.

S&F in repair 75mm bore CI socket double collars with oval access door fixed with lead joints complete all as specified and directed.

S&F in repair 75mm bore CI branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and directed.

S&F in repair 100mm bore bend with duck's foot or heel rest complete all as specified and directed.

S&F in repair 75mm dia bore bend with duck's foot or heel rest complete all as specified and directed.

S&F in repair ball valves (brass) high pressure with polythene float and fly nut screwed for 20mm bore iron pipe or brass ferrule complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n. exc. 15 cm thickness below or above ground level including removal of rubbish outside MoD land complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate and finishing the surface even and smooth without using extra cement as in plinth protection complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, apron etc. laid bedded and pointed in any mortar including removal of rubbish outside MoD land complete all as specified and directed.

M&L machine cut Kota stone slab 18-20mm thick as in flooring including strip 50 to 75mm wide laid over and including 20mm thick screed bed in cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L machine cut Kota stone slab flooring 18-20mm thick in riser of steps, skirting, dado and pillar laid with neat cement slurry over and including 10mm thick backing coat in cement mortar (1:3) including pointing in white cement with pigment to match the shade of slab complete all as specified and directed.

M&L for point wiring complete with single core multi stranded copper conductor cable of size 1.5 sqmm PVC insulated unsheathed 1100 volt grade in and including PVC conduit of size 20mm dia or higher including Tee, junction, bends etc concealed in wall/ fixed on ceiling and including MS modular boxes of suitable size for housing modular switches, sockets etc. including 1.5 sqmm green PVC insulated wire for earth continuity for the following including taking down existing point wiring complete all as specified and directed:-

One light/ exhaust fan point controlled by one way switch or fan point controlled by one way switch through regulator.

One bell point controlled by one bell push.

One three pin 5 amp socket outlet multipurpose on independent board.

One three pin 5 Amp switch socket cum on same board.

One light point controlled by 2-two way switch

All as per item No 105.00 above but with 2.5 sqmm cable insulated for 3 pin 15 amp multipurpose outlet including 2.5 sqmm PVC insulated copper wire for earth continuity on independent board complete.

S&F modular switch 1 way, 6 A, 1 module all as specified and directed.

S&F modular switch 1 way, 16 A, 1 module all as specified and directed.

S&F modular bell push 6 A, 1 module all as specified and directed.

S&F modular socket outlet, 2/ 3 pins combined, 6 Amps, 2 module, 230 volts all as specified and directed.

S&F modular socket outlet, 2/ 3 pin combined, 6/ 16 Amps, 2 module, 230 volts all as specified and directed.

S&F modular white cover plate with frame 1 module all as specified and directed.

S&F modular white cover plate with frame 3 module all as specified and directed.

S&F modular white cover plate with frame 4 module all as specified and directed.

S&F modular white cover plate with frame 6 module all as specified and directed.

S&F ceiling rose, surface bakelite, 65 x 50mm, two to three terminals all as specified and directed.

S&F modular fan regulator step type 120 W, 2 module for ceiling fans including necessary connections 240 volts, 50Hz complete all as specified.

S&F bell multi music type single pole AC 230 volts 50 Hz all as specified and directed.

S&F modular switch 2 way 6A, 1 module all as specified and as directed.

M&L for submain wiring complete with two runs of 4.0 Sqmm single core, multi-stranded, FR PVC insulated unsheathed cable 1100 volts grade with copper conductor, drawn through and including rigid non metallic PVC conduit medium grade ISI marked 25mm external dia concealed in wall/ floor along with conduit fittings and accessories, fixed on ceiling with one run of 2.5 Sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor and connecting to common earth dolly including taking down existing submain wiring with conduit any type complete all as specified. Note: Two runs of 4.0sqmm multi-stranded cable and one run of 2.5sqmm cable as earth continuity conductor alongwith PVC conduit shall be considered as one unit length.

M&L for submain wiring complete with two runs of 6.0 Sqmm single core, multi-stranded, FR PVC insulated unsheathed cable 1100 volts grade with copper conductor, drawn through and including rigid non metallic PVC conduit medium grade ISI marked 25mm external dia concealed in wall/ floor along with conduit fittings and accessories, fixed on ceiling with one run of 4.0 Sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor and connecting to common earth dolly including taking down existing submain wiring with conduit any type complete all as specified. Note: Two runs of 6.0sqmm multi-stranded cable and one run of 4.0sqmm cable as earth continuity conductor alongwith PVC conduit shall be considered as one unit length.

S&F in repair decorative ultra slim LED light fitting four feet long energy efficient complete with LED lamp 18/ 20 watt 230 volts, box type CRCA sheet housing and connecting up with twin twisted flexible copper conductor cable with suitable size complete all as specified and as directed.

S&F LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete with all accessories pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply, fix, connecting and testing factory made, MCB distribution board (MCB DB), IP 43, SPN, 8 way, 240 Volts, double door, flush type made out of 1.2mm thick CRCA sheet metal, Phosphatised, duly powder coated and conforming to IS 13032 with 200 Amps rated bus bar, neutral link, earth bar and din rail etc. complete fixed in switch board/ wall including taking down the existing one complete all as specified and directed. Note: MCBs shall be measured and paid separately.

S&F in replacement of sheet metal enclosure for incoming MCCB and outgoing MCBs factory made double door, TPN 415 volts 6 ways with 200 Amp bus bar with IP43 protection complete in all aspects all as specified and directed.

Supply and fix single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 6 to 32 Amps, 230 volts including taking down old one complete all as specified and directed.

S&F in replacement MCB SP 5 to 32 Amp 240 volts 10KA, 'C' curve complete all as specified and directed.

S&F in replacement isolator SPN 40 Amp 240 volts, 10KA, 'C' curve complete all as specified and directed.

S&F in replacement MCB TPN 63 Amps, 25 KA, 415 volts grade, complete all as specified and directed.

S&F in replacement of MCCB 63 Amps, 4 pole, 16 KA, AC, 415 V conforms to IS/ IEC: 60497-2 with fixed thermal and fixed magnetic setting Ics=100% of Icu complete all as specified and directed.

Taking down ceiling fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed.

M&L for filling cavities with filler and painting of ceiling fans with synthetic enamel paint using spray gun complete all as specified and directed.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

S&F in replacement of exhaust fan 300mm sweep, 230 volts complete with louvers shutter, steel body and connecting up as suitable to exhaust fan including provision of cable from ceiling rose or connector to exhaust fan complete all as specified and directed. Note: Old U/s exhaust fan shall be deposited to MES store and proof of the same shall be produced by the contractor for claiming payment against this item.

M&L for making hole for exhaust fan 300mm sweep and embedding nuts and bolts etc. of suitable size including making good to disturbed surface to match with existing one complete all as specified and directed.

S&F in replacement decorative energy efficient LED street light fitting 1x 20 watt complete with LED lamp and 40mm dia GI bracket 1.2m long and connecting up with twin twisted flexible copper conductor cable with suitable size complete all as specified and as directed.

S&F rigid non-metallic PVC conduit 40mm dia exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and as directed.

Earthing complete with galvanized steel earth plate electrode of size 600mm x 600mm x 6.0mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.5m below normal ground level, earth plate connected to galvanized iron earth wire of 4mm dia as earthing conductor by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES Schedule (Part I) (2009) connected to earth test point/ main switch/ DB/ Panel board all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 meter long for earth strip including PCC (1:3:6), type C-1 pit with 40mm thick precast RCC (1:2:4), type B -1 cover reinforced with 12mm dia MS bars @ 150mm c/c both ways with lifting hooks made out of 12mm dia MS bars, wire mesh funnel with watering pipe 20mm dia light grade, common salt, charcoal filling in layers as specified, necessary excavation and earth work in any type of soil etc., including dismantling existing earthing complete all as specified and as directed.

M/S MATLOOB AHMED

M/s Bhagwati Enterprises

PARVEEN KUMAR AND SONS