REPAIR TO BLDG AND PERIODICAL SERVICES IN VARIOUS UNITS AT SURANKOTE AND REPAIR/ REPLACEMENT TO E/M INTERNAL FITTINGS/ FIXTURES AND WIRING IN VARIOUS UNITS AT GULPUR, SEKLU AND NATU UNDER UNDER GE 881 EWS

Amount

B&R PORTION:- Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed.

Dismantling of timber scantling under 40sqcm in section unframed work as in fillets, rails, posts, rafters, purlins etc, complete all as specified and directed.

S&F 4 mm thick E-board (Classic) including fixing of frame work made up of special MS section, galvanized sheet with zinc coating cellular intro painting and consisting of angle cleats of size 25 mm wide, 1.6 mm thick with flag fixing to the ceiling with dash fastener 12.5 mm x 40 mm long or with 2 mm dia GI wire or fixed with bolts in GI channel main of size 35x25x0.5 mm thick and cross runner of size 25x25x0.5mm for fixing E-board of size 600x600mm x4 mm thick including fixing of E-board with ceiling section and perimeter of channel 25x25x1mm thick, 27mm high flange of 20mm to 30mm long extra including application of two coats of oil emulsion distemper, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, including filled the joints with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base floor finishing surface even and fair, complete all as specified and directed.

M&L for cement concrete (1:2:4) type-B-1 (using 20mm graded stone crushed aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, bed block, kneelers, apex stones, bed plates, roof kerbs round or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for Chequered cement concrete tiles 300x300x 25mm thick, set & jointed in neat cement slurry in floors and pointed with grey cement mixed with pigments, laid over and including 20mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for vitrified ceramic tiles, light shade, 10 mm thick (square/rectangular) area of each tile not exceeding 0.36sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

All as per ser item No.12 above but as in vertical surfaces of wall such as in dado/skirting etc. fixed over & including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

All as per ser item No.14 above but as in vertical surfaces of wall such as in dado/skirting etc. fixed over & including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.06 Sqm but n exc. 0.11 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for glazed ceramic coloured tiles (300x200mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

M&L for walling of random rubble stone masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

All as per item No. 19 above, but except stone complete all as specified and directed

Extra over stone walling of random rubble walling, uncoursed or brought for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified and directed.

M&L for rendering 20mm thick on other than fair faces of brick or stone masonry wall surfaces in cement mortar 1:4 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick cement plaster rendering in CM 1:4 on fair faces of bricks or concrete surfaces, chajja and suspended work, finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on other than fair faces of brick or stone masonry wall surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

M&L for preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of oil emulsion distemper over and including 1 mm thick wall care putty, complete all as specified and directed.

M&L for applying three coats of white wash including preparation of newly plastered surfaces of wall complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Dismantling of timber scantling 40sqcm and over in section, as in any position, complete all as specified and directed.

S&F 0.63mm thick galvanised corrugated mild steel sheeting with grade of Zinc coating of 275 gms/Sqm with two corrugation side lap and at least 150 mm end lap , fixed with L or J type or cranked hook bolts, in roof, walls etc, complete all as specified and directed.

All as per item No. 31 above, but except sheets, complete all as specified and directed.

S&F 0.80mm thick plain galvanised mild steel sheeting with 275 gm/sqm Zinc coating as in ridge , hips, valley gutters, drip and straight flashingfixed with L or J type or cranked hook bolts, in roof etc., complete all as specified and directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connected plate confirming to Fe 410W(Gde E-250), quality 'A' complete all as specified and directed.

S&F mild steel work as in wind ties for roof including securing bolts, including all necessary drilling, bolting or riveting etc. and similar work conforming to Fe-250 Gde E-165 complete all as specified and directed.

S&F 2nd class soft wood (Kail) as in scantling, clean sawn timber fixed, complete all as specified and directed.

Taking down shutters of any description exceeding 1sqm and not exceeding 2sqm each, complete all as specified and directed.

Taking down shutters of any description not exceeding 1sqm each, complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm and not exceeding 4Sqm each, complete all as specified and directed.

S&F 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood plain, framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of 12mm thick veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc divided into square (with sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

S&F 30mm thick 2nd classhard wood glazed and skeleton shutters, for window/ventilators, open rebated and prepared to receive glass, gauge etc divided into square (with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (b) supplied and fitted to chowkats complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam (Nut brown colour) PVC Sheet on the front face & 2mm prelam (Nut brown colour) PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed. Note:- Cadmium screws to be used for fixing and fixtures of fittings.

S&F mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled,75mm long, complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section of size 100mm and fixed, complete all as specified and directed.

S&F aluminium alloy handles, cast type, anodised of size 150mm and fixed, complete all as specified and directed.

S&F aluminium alloy handles, cast type, anodised of size 100mm and fixed, complete all as specified and directed.

S&F 250mm long aluminium alloy anodized sliding door with haps, staple (bolt type) and fixing clips of sheets, cast or extrusted sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beading, complete all as specified and directed.

S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of Ist quality over a coat of pink primer, complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

S&F steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in repair bib tap 15 mm bore with flange, Brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed. Make:- Jaquar cat part No CON-047KN or equivalent cat part of make as specified in P.S.

S&F in repair angular stop valves cast copper alloy 15 mm dia, chromium plated with wall flange screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions complete all as specified and directed. Make-Jaquar Cat Part No:-CON-059KN or Equaivalent cat part of make as specified in P.S.

S&F in repair vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, snow white, with 'P' or 's' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete all as specified and directed. Make:- Prayag cat part No-4054 or Equaivalent cat part of make as specified in P.S.

S&F in repair PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints, complete all as specified and directed. Make:- Prayag cat part No 501 or Equaivalent cat part of make as specified in P.S.

S&F in repair vitreous china wash hand basin, white, flat back, size 550x400 mm excluding taps, waste, chain & plug and porcelain stopper but including brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed. Make-Prayag Cat Part No:-4645 or Equaivalent cat part of make as specified in P.S.

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 450mm complete all as specified and directed.

S&F in repair 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe complete all as specified and directed. Make:- Jaquar cat part No-CON-011KN or equivalent cat part of make as specified in P.S.

S&F in repair 32mm dia PVC corrugated waste pipe with union 800mm long complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint to walls as soil pipe with & including clamps, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint to walls as soil pipe with & including clamps, complete all as specified and directed.

S&F in repair vitreous china urinals, bowl type of size 465x355x265mm (minimum) white with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with automatic flushing cistern with brackets, flush pipe, waste pipe grating and union for discharge pipe complete all as specified and directed. Make:- Prayag cat part No-4999 or Equaivalent cat part of make as specified in P.S.

S&F in repair grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), suitable for floor taps, complete all as specified and directed.

Dismantling PVC water tanks and removing to store of capacity not exceeding 500 ltr complete all as specified and directed.

Dismantling PVC water tanks and removing to store of capacity exceeding 500 ltr and not exceeding 1000 ltr complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 500 Ltrs incl with 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs incl with 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames or stone/ concrete, glazed with putty or fixed with beads, complete all as specified and directed.

S&F sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed.

S&F figured glass pin headed type, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beading, complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and as directed.

S&F in repair MS powder coated tubular curtain rod fancy type of 25mm dia complete all as specified and directed.

S&F in repair MS powder coated decorative type bracket, end ball, rounded block, bracket (coated with brown/cherry/golden colour) suitable for 25mm dia curtain rod of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and directed.

S&F mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type-C1 (using 20mm graded crushed stone aggregate) as in copings, hold fasts plinth band, bed blocks and like slightly rounded or chamfered angles as directed including necessary form work, complete all as specified and directed.

S&F in repair chromium plated hand shower (Health faucet) with 1.5m long flexible tube of stainless steel in chrome finish and wall hook complete all as specified and directed. Make: Jaquar code No ALD-CHR-583 or equivalent as approved by GE.

S&F in repair CP jet spray with holder including 1.5m long PVC/Chromium plated flexible PVC pipe, necessary nut bolts and PVC washers fixed with PVC seat cover for pedestal pattern water closet, complete all as specified and directed.

S&F in repair plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised or PVC hinging device complete all as specified and directed.

S&F in repair PVC water tank cover suitable for 500ltrs/1000ltrs water tank, complete all as specified and directed.

Taking down existing roof treatment of any description in any condition including removing of cement plaster of concrete of any description from the roof surfaces and removing all the debris to a distance n.exc 100m and roughening surfaces by sweeping clean and washing down with water to remove dust etc and applying evenly cement slurry at the rate of 3 Kg/Sqm over cleaned surfaces and providing 10 mm thick cement screed in CM 1:4 , finished surface even and smooth, after that cleaning the entire roof surface thoroughly to remove all loose particles, dust/dirt particles and applying with one coat of industrial bituminious primer at the rate of 0.40 lit/Sqm over the plastered surfaces of roof and applying a course of a coat of binding material with blown type bitumen of grade 85/25 heating to working temperature of 180 0 C @ 1.2 kg/sqm then applying APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) laid with 75 mm side overlap and 150 mm overlap primed surfaces by forced (tourch) application as per manufactures instructions and applying two coats of aluminium paint over APP membrane, complete all as specified and directed.

Cleaning / disinfecting of PVC / RCC water storage tank of any capacity with disinfecting chemicals (Chlorine) properly with water thoroughly flushed out, complete all as specified and directed.

M&L for preparation of old plastered/ un-plastered wall surfaces including brooming down or steel wire brushing, scraping down, smoke soot, mould, moss, efflorescent salts, trading oil and greasy spots, and applying one coat of white wash on walls including cornices, pilasters etc, complete all as specified and directed.

M&L for complete removal of existing treatement and applying two coats of white wash on wall, complete all as specified and directed.

All as per item No. 92 above, but on ceiling, complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying one coat of oil bound distemper white or any tint, complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying two coats of oil bound distemper white or any tint, complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying one coat of cement base paint, complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying two coats of cement base paint, complete all as specified and directed.

M&L for preparation of old painted steel surfaces/CGI/PGI sheets of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint in camouflage pattern, complete all as specified and directed.

M&L for preparation of old painted wooden or wood based surfaces of any description not otherwise described, over 10cm width or girth including knotting and stopping as required and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for applying wall care putty of approved make 3mm thick on walls as per manufacturer's instructions with and including rubbing by means of sand paper to have smooth finishing to receive primer / paint, complete all as specified and directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) n. exc 30cm high with synthetic enamel paint including oblitering old writing of any description to match existing work, complete all as specified and directed.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and mirror polishing laid over & including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

S&F in anodised aluminium swing type door shutter fully glazed with chowkhat, including 5 mm thick coloured glass panes with lock rail and aluminium anodized standard beads/glazing clips having weight not less than 300 gms per RM, aluminium anodized cast type round handle 125mm on both sides, 02 Nos aluminium anodized door stopper, floor spring, 1 No. tower bolt of size 200mm, brass mortice lock six lever with three keys, all mongery ISI marked, size of member of shutter shall be as under complete all as specified and directed. (a) chowkhat 100 mm x 44.5 mm x 2mm thick (b) Bottom rail 114.3mm x 44.5mm x 2mm thick (c) Lock rail 85mm x 44.5mm x 2mm thick (d) Top rail 85mm x 44.5 mm x 2mm thick

S&F in repair anodised aluminium window fixed type sutters, with or without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc., with & including 5 mm thick tinted glass pane complete all as specified and directed.

S&F in repair powder coated anodised aluminium (minimum 15 micron) frame section of size 101.6 mm x 44.45mm x 2.40 mm thick, top & bottom rail of section 83 x 44.5 x 2.4mm and 100X44.50mm x 2.4 mm thick respectively, size of styles 80mm x 44.5mm x 2.4 mm thick and 100mm x 44.5mm x 2.4 mm thick including all necessary jointing cleats glazing clips, rubber packing, anodized aluminium beading for fixing prelaminated particle board 12 mm thick, interior grade prelaminated both sides with decorative choice laminations on both side panes complete all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F in repair 12mm thick both sides prelaminated particle board, medium density fixed with screw to frame work in cup board shutters, partitions, shelves etc acomplete all as specified and directed.

E&M PORTION:- Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

Taking down carefully unsv sub main wiring including earth continuity any type/ size with surface casing/ caping/ TW batten/ PVC conduit surface or recess etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and directed.

M&L for point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light/fan point controlled by one way switch 6 Amp complete all as specified and directed.

One ligh point controlled by two numbers, two way switch 6 Amp complete all as specified and directed.

One 3/5 pin socket outlet 6 amp on same board complete all as specified and directed.

One 3/5 pin socket outlet 6 amp independent board complete all as specified and directed.

One bell point controlled by one way switch 6 Amp complete all as specified and directed.

All as per srl item No 110 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 2.5 Sqmm as in continuous earth wire complete all as specified and directed.

S&F in repair ceiling rose, 3 terminal, surface bakelite 65 mm x 50mm, PVC/poly carbonate, insulated body, complete all as specified and directed.

S&F in repair switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed.

S&F in repair switch piano flush type 6 Amp two way, (ISI marked), complete all as specified and directed.

S&F in repair switch piano bell push flush type 5 Amp single pole one way (ISI marked) complete all as specified and directed.

S&F in repair socket outlet 2 in 1, 3 pin, 6 Amp flush type universal, complete all as specified and directed.

S&F in repair Switch socket combination, 5 pin, 5 Amp flush type universal, complete all as specified and directed.

S&F in repair Switch socket multipurpose combination 2 in 1, 5 pin, 5 and 15 Amp flush type universal, complete all as specified and directed.

S&F in repair Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

S&F in repair stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. for 1200 / 1400mm sweep, complete all as specified and directed.

S&F in repair electric bell ding dong type 230 volts AC supply 50 Hz complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair inverter LED batten 1x 20W, with square profile and polycarbonate channel, lithium iron battery with charging time of 8 to 10 hours and backup tile upto 04 hours with driver, holder incl LED tube light connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make : Havells cat part No. LHEXACP7FN1W020 or equivalent make as specified in PS

Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. all as specified and directed.

S & F in repair LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size Complete all as specified and directed.

Supply and fixing in repair ceiling mounting LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F in repair gate light fittings, outdoor type, high power , 25 watt, IP65 luminaire, prewired with suitable pole for mounting complete all as specified and directed. Make: Havells cat part No. Coral Opal IP65 or equivalent make as mentioned in PS

Supply and fixing in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver including suitable bracket fixed to wall/pole complete with IP 65/66 protection complete all as specified and directed.

S&F in repair LED inverter lamp CDL 10 watt with holder base (B22) type, complete all as specified and directed. Make of LED lamp:- Havells cat part No LHLDEUEEML8R010 or Equivalent cat part of make as specified in P.S.

S&F in repair LED driver suitable for 34 watt LED ceiiling light fittings and making connection to fitting complete all as specified and directed. Make:-Havells cat part No-LEDDRIVER36V36WS or Equivalent cat part of make as specified in Appx 'A' to P.S.

S&F in repair single pole and neutral enclosure with a two pin and metal earth plug and socket complete with & incl one single pole MCB of 20 Amps complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, vertical TPN double door (IP43), 4 ways built in bus bars suitable for 415 volts, AC, 50 Hz and suitable for FP MCCB as incommer and out going SP/TP MCBs complete all as specified and directed. Note:- MCBs shall be measured and paid separately.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 4 ways built in bus bars suitable for 240 volts, AC, 50 Hz , including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 8 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 12 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair MCB TPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCTNF040 - DHMGCTNF063 or Equivalent cat part of make as specified in P.S.

S&F in repair MCB SPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCSNF040 - DHMGCSNF063 or Equivalent cat part of make as specified in P.S.

S&F in repair MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series complete all as specified and directed. Make:-Havells cat part No-DHMGCSPF006-032 or Equivalent cat part of make as specified in P.S.

S&F in repair Switch socket multipurpose combination 5 in 1, 20/16 amp flush type universal including box with 4 fixing holes, complete all as specified and directed.

S&F in repair Switch socket multipurpose combination 2 in 1, 6 amp flush type universal including box with 4 fixing holes, complete all as specified and directed.

Taking out old unsv exhaust fan from site and replacement of exhaust fan made up of sturdy engineering plastic complete with louvers shutter, voltage 230 V, 50 Hz, 1200 RPM, copper winding of sweep 300mm incl all connecting accessories complete all as specified and directed by Engineer-in-charge.

Taking out old unsv exhaust fan from site and replacement of exhaust fan steel body, AC single phase, voltage 230 V, 50 Hz, copper winding of sweep 300mm incl all connecting accessories complete all as specified and directed by Engineer-in-charge.

Taking out old unsv exhaust fan from site and replacement of exhaust fan steel body, AC single phase, voltage 230 V, 50 Hz, copper winding of sweep 450mm incl all connecting accessories complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC casing caping of size upto 32 mm incl all fixing accessories complete all as specified and directed.

S&F Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing, complete all as specified and directed.

S&F Sub main wiring with single core cable 2x 4 Sqmm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 4 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-Three wire of 4 sqmm and one run of PVC conduit/casing caping shall be measured as one unit.

S&F Sub main wiring with single core cable 2x 6 Sqmm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 6 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-Three wire of 6 Sqmm and one run of pvc conduit/casing caping shall be measured as one unit.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat or circular of size 6 Sqmm 2 core & including taking down old old unsv service cable connection, complete all as specified and directed.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat of circular of size 10 Sqmm 2 core including taking down existing old service connection, complete all as specified and directed.

Repair and maintenance of unserviceable ceiling fan of 1200mm/1400mm sweep at contractor's work shop, incl dismantling complete the ceiling fan parts, inspecting serviceability of all the parts, refixing of serviceable parts after cleaning and replacement of unserviceable parts with company's genuine parts i.e. capacitor, bearing, bushes, shaft, bracket, rubber bush, connecting wire, PVC connector, aluminium clamp for rod, bracket, bush rod, greasing/oiling etc assembling, cleaning and testing of ceiling fan complete all as specified and directed. Note: (i) Unserviceable parts as above shall be measured and paid separately under relevant items of Sch 'A' item No 150 to 155 as supply only. (ii) Rewinding of stator will be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. Cotter pin, screws shall be deemed to included in the cost of quoted rate.

Supply only bearing good quality for ceiling fan 1200mm/1400mm sweep ISI marked complete all as specified and directed.

Supply only Gun metal bush for ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

Supply only capacitor 2.5 mfd ISI marked complete all as specified and directed.

Supply only brass bracket assy for hanging the ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

Supply only 3 core flexible wire 40/.0076, white colour from ceiling rose to fan connector complete all as specified and directed.

Supply only stator shaft for ceiling fan complete all as specified and directed.

Taking out old u/s ceiling fan from site of capacity 1200/1400 mm sweep and replacement with and incl new BLDC ceiling fan of 1200 mm sweep, 230 V, 50 Hz incl all connecting accessories complete all as specified and directed.

M&L for removing of old burnt winding of ceiling fan any size , type and rewinding of stator winding with superior quality copper wire with insulation complete all as specified and directed.

Repair and maintenance of unserviceable exhaust fan of any cap and sweep by dismantling the exhaust fan parts, inspecting the serviceability of parts, refixing of serviceable parts after cleaning, replacement of unerviceable parts i.e. beaing, bush, capacitor, connecting wires, fan blade, locknut, rubber pad etc, oiling/greasing, cleaning and testing of exhaust fan complete all as specified and directed. Note: (i) Unserviceable parts replaced shall be measured and paid separately under relevant items of Sch 'A' item No 159, 160 & 163 as supply only. (ii) Rewinding of stator winding shall be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. screws shall be deemed to included in the cost of quoted rate.

Supply only double ball bearing (ISI marked) for exhaust fan of 200 mm sweep to 450 mm sweep fan complete all as specified and directed.

Supply only gun metal bush for Exhaust fan of any capacity. complete all as specified and directed.

M&L for rewinding of 450mm sweep exhaust fan motor with superior quality copper winding wire with insulation complete all as specified and directed.

M&L for rewinding of 300mm sweep exhaust fan motor with superior quality copper winding wire with insulation complete all as specified and directed.

Supply only blade of exhuast fan of 200 mm sweep to 450 mm sweep as per existing make complete all as specified and directed.

narayan construction

M/S Chib Engineers

M/S KHAN ENTERPRISES

SUNIL KUMAR SANGEET KUMAR AND SONS

M/S BADRI NATH GUPTA

JAMWAL CONSTRUCTION CO

M/s Anil Engineers & Builders