REPLACEMENT OF DEFUNCT LED FITTINGS, SWITCHGEAR AND OTHER ALLIED ACCESSORIES IN PUNJAB ENGINEERING COLLEGE AT U.T CHANDIGARH AT PUNJAB ENGINEERING COLLEGE, SECTOR-12, CHANDIGARH.(2025-26).

DSR item no. 2.10Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Double pole

Triple pole and neutral

Supplying and Erection of MCB TPN of 63 amp. The MCB TPN shall be installed in existing enclosure with suitable arrangement. The job includes cost of labour, incoming & outgoing connection and other petty material required to complete the job to the entire satisfaction of Engineer –in-charge of the work. The MCB TPN should be of Schneider/ Siemens/ Havells make only

DSR Item No.2.2Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubical panel board including drilling holes in cubicle panel, making connections, etc. as required.

63/100 A,30KA,FPMCCB

125A, 36KA,FPMCCB

200A, 36KA,FPMCCB

250 A,36KA,FPMCCB

630 A,50KA,FPMCCB

S/E of enclosure for MCCB 4 pole made out of 16 G MS sheet. The Enclosure should be painted after one coat of primer after rubbing the surface with sand paper. The job includes the cost of its erection in existing angle iron board with nut bolts/ screws etc. The enclosure should be of following size.

Size of enclosure for 63/100 amp 4 pole

Size of enclosure for 125 amp 4 pole

Size of enclosure for 200 amp 4 pole

Size of enclosure for 250 amp 4 pole

Size of enclosure for 630 amp 4 pole

DSR 9.1 Brush Less Direct Current (BLDC) without remote Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal ( Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan Supply, earthing etc. complete as req

1400mm, service value ≥ 6.0 CM/Min/Watt, air delivery 245 CM/Min (Minimum)

1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum)

S/E of fresh air fan high speed motor with copper would 10” sweep with louver and plastic body complete with speed motor, blades, epoxy powder coated of Havells make Ventilator DX white/ Orient make ventil air-ZX/ Crompton make Brisk Air/ Usha Crisp air/ Bajaj Supreme maxima DXI only. The cost includes the connection with adjacent light points and installed on wall with suitable arrangement by providing frame of required size made out 6mm thick water proof plywood to be installed with suitable size rag bolts, nuts after making suitable size hole in the wall if required at site to the entire satisfaction of Engineer-in-charge.

DSR item no.8.10.5 LED Batten light (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85% ,Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast / Extruded aluminium Body (Thickness ≥ 1.20 mm)

DSR Item No.1.17 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

1 x 1.5 sq. mm

3 x 1.5 sq. mm

3 x 2.5 sq. mm

3 x 4 sq. mm

DSR Item No.1.24Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

3 pin 5/6 A socket outlet

15/16 A switch

6 pin 15/16 A socket outlet

2 way 5/6 A switch

Bell push

DSR Item No.1.27Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

DSR Item No.1.26Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

DSR Item No.1.21Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing Socket type stepped up electronic fan regulator on the existing Bakelite sheet switch box including connections but excluding Bakelite sheet etc. as required.

Supply and Erection of B.L Holder of make anchor/ havells ISI marked on the existing junction box/ wooden block including making the connection etc as required. The job includes the all labour and petty material charges required to complete the job to the entire satisfaction of E.I.C. of work.

DSR Item No. 1.23Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required.

5/6 amps switch

3 pin 5/6 A socket outlet

15/16 A switch

6 pin 15/16 A socket outlet

Supply & Erection of 3 mm thick white glazed Bakelite sheet on existing M.S. box. The job includes the cost of sheet and making holes & cutting and fixing with screws as required to complete the job.

Supply & erection of PVC junction cover on existing junction box. The junction cover should be superior quality. The job includes all labour and petty material to complete the job to the entire satisfaction of the Engineer In Charge of work

DSR Item No.1.28Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

1 or 2 Module

3 Module

6 Module

8 Module

DSR item No.1.38 Supplying and fixing call bell/ buzzer suitable for single phase,230 V, complete as required.

Supply and erection of modular type DP switch 32 Amp on existing modular box with the help of suitable arrangement require to complete the job. The DP switch should be of L&T/ ABB/ Schneider / Anchor make only. The job includes cost of labour, making connection and other petty material required to complete the job to the entire satisfaction of Engineer in charge of the work.

Supply & erection of Exhaust Fan (heavy duty motor with copper wound metallic body) following size complete with motor, metallic blades, double ball bearing with minimum power consumption, rigid frame with rubber mounting for silent operation, epoxy powder coating along with metallic louver to be installed in the existing opening including cost of making the hole to suit the size of above fan making good the damage, Carriage Charges connection, testing, commissioning etc. as required to complete the job to the entire satisfaction of EIC. The Exhaust fan should be Havells/ Orient/ Usha/ Crompton/ Bajaj make only.

Size 12 inches (300mm) Sweep, 900 RPM Heavy Duty Exhaust fan (Single Phase) with louver of Havells make (Turbo Force SP)/ Crompton make ( EXHD300-6-1)/ Bajaj make (Supreme Plus)/ Orient make (Industrial Heavy Duty)/ Usha Make (Turbo HDEF) make only.

Size 15 inches (380mm) Sweep, 900 RPM Heavy Duty Exhaust fan (Single Phase) with louver of Havells make (Turbo Force SP)/ Crompton make ( EXHD380-6-1)/ Bajaj make (Supreme Plus)/ Orient make (Industrial Heavy Duty)/ Usha Make (Turbo HDEF) make only.

Please Enable Macros to View BoQ information