SPECIAL REPAIR TO BLDG NO TW - 33 (AIR FIELD AREA) MCTE, INCLUDING CERTAIN REVENUE WORKS UNDER GE (MCTE) MHOW

Amount

Dismantling Asbestos Cement Corrugated or Semicorrugated in Roof covering .

Dismantling/ wall and ceiling boards (fibre pulp, insulation etc) or insulation boards/ slabs complete all as specified

Dismantling fillets,rails,posts,rafters,purlins,etc under 40Sqcm in section

Demolition of cement concrete (un-reinforced) in ground floor and paving n.exc 15cm thickness (below or above GL)complete removal of debris outside MD land.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc. complete removal of debris outside MD land.

Demolition of stone slabs and tiles of any description or thickness in floors/ walls laid bedded and pointed in any mortar

Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including Racking out Joints, hacking for Key, scrubbing down with Water, etc. complete removal of debris outside MD land.

Demolition of brick work or PCC solid block or stone/boulder masonry built in cement mortar.

Taking down shutter of any description exc 1 Sqm and n exc 2 sqm including easing & adjusting shutters and refixing in the same opening all as specified and directed.

Taking down chowkats or frames with shutters (with out taking off shutters from the frames) n. exc 1.50 Sqm each.

Taking down chowkats or frames with shutters (with out taking off shutters from the frames) exc 1.5sqm but n. exc 4 Sqm each.

Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each .

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelam PVC sheet used instead of plain colour PVC sheet and edges will be painted to match with reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawingwith prelam sheet complete all as specified.

S&F Factory made solid panel pvc door shutter 30 mm thick consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15 x 15mm for top & bottom rails. M.S. frame shall have a coated of steel primers of approved make and manufacture . MS frame covered with 5mm thick heat moulded PVC "C" channel of size 30mm thickness ,70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming styles and 5mm thick 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to from top and bottom rail and 115mm vide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to from lock rail . Top , bottom and lock rail shall be provided either side of the panel 10mm (5mm x 2)thick ,20mm wide cross PVC sheet to be provided as gap insert for top rail & bottom rail. panelling of 5mm thick both side PVC sheet to be fitted with MS frame welded / sealed to the stiles & rails with 7mm (5mm + 2mm )thick x 15mm wide PVC Sheet beading to inner side and jointed together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the C channel using PVC solvent adhesive etc. suppling & fixing in the frame at site as per specification & drawing

S&F Pressed steel frames for doors size 125x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified

S&F Pressed steel frames for doors size 105x60mm with one rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified

S&F 2nd class hard wood glazed and skeleton shutters, 35mm thick, open rebated & prepared to receive wire gauge (with sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitread beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I, section 8, clause 8.24- (a), supplied and fitted to chowkats.

S&F 35 mm thick second class hard wood rail and style plain framed factory made panelled shutter (two panel) with lock rail and panel of 12 mm BWP commerical ply . The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Providing and fixing pre painted steel sliding window 3-Track, 2 glass panel and 1 mesh panel sliding window fabricated from Roll formed sections made of galvanized Steel colour coated/powder coated (Base Steel as per IS 513 ‘D’ quality, galvanized as per IS 277 with zinc of 120 GM/Sq.mtr) with total coated thickness of 0.58mm. Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick. Section for external frame should be of 107x44mm, Section for shutter should be of 35x49mm. Section of mesh should be of 35 x 49 mm.The windows should be paneled with 5mm thick plain float glass. Corner bracket for internal and external frame made of glass filled nylon. Gaskets are to be made of Ethyl Propylene Diamine Monomer (EPDM).The sections are to be cut to length, joined and assembled by means of corner bracket. The above frames should be fixed to the concrete/masonry walls by means of self expanding screws . Make : NCL Coloured GI Windows

S&F Framed work such as grills, gratings, guard bars for windows, and ventilators, barred iron work, ladders, framework of water tanks and similar work.

S&F stainless steel wire cloth 0.45 mm nominal dia of wire and average width of aperature 1.40 mm fixed with wooden beeds.

S&F Butt hinges 100mm mild steel cold rolled, medium weight.

Supply only 50mm mild steel medium weight butt hinges.

S&F small fittings such as brackets of any type latch and hinges block shaped door and window stops and the like incl all necessary labour articles not ec 200 Cucm each in 2nd class hard wood all as specified.

S&F 150mm long aluminium handles, cast type anodized.

S&F 200mm long aluminium, anodized barrel tower bolts of extruded section

S&F 150mm long aluminium, anodized barrel tower bolts of extruded section

S&F 300mm aluminium alloy, anodized, sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy

S&F door spring with 300mm mild steel rat rail rod pattern of standard quality including roller and roller plate complete Helical spring)

S&F Mild steel work as in band, strap, hold fast, cleat, hook, hinges, base tie for door frame, support or stay for rain water pipe etc and other similar items conforming to Fe-410-0 or Fe-310-0 complete all as specified and as directed.

Cutting holes in stone/brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1;2:4 type B1 exceeding half brick but not exceeding one brick all as specified and as directed.

M&L Cement concrete 1:2:4, type B0 (12.50mm graded stone aggregate) for 25mm thick floor as in sub base for floor tiles

M&L Non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including 15 mm thick screed bed in CM 1:6

M&L for coloured glazed ceramic tiles (colour as approved laid in pattern as approved by GE )size 300x 450mm x 7 mm thick on vertical surfaces such as dados and risers to step etc, set and jointed in neat cement slurry and pointed in coloured cement to match the tiles including 10mm thick rendering in CM 1:4.

M&L for Double charge/ultracharged vitrified tiles of any colour 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick bedding layer in cement sand mortar 1:6 complete all as specified and directed.

M&L for Double charge/ultracharged Vitrified ceramic tiles 10mm thick of any shade (square / rectangular) area of each tile as in as in skirting or on vertical surfaces, not exceeding 0.36 sqm, etc .set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 10mm thick backing coat in cement sand mortar 1:4 complete all as specified and directed.

M&L 16 to 18mm thick Granite (of any type) work (table rubbed and polished and exposed visible edge moulding/rounding ) in steps, jambs, pillars, window cills, cooking platforms and like in 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M&L for 75mm thick subbase ,cement concrete type D2,1:4:8 using 40mm graded Agg as in finished even and fair complete all as specified.

M&L for 300 x 300 x 15mm thick heavy duty ceramic floor tile laid in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match fixed over and including 20mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection finished even and fair incl cutting joints and filling with bitumen and sand mixturecomplete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar (1:6) on faces of brick work and finished the surface fair and even without using extra cement complete as specified and directed

M & L rendering 15mm thick on fair faces of brick work or concrete surface in CM 1:4 surface finished even and smooth without using extra cement.

M &L for preparation of newly plastered surface and applying two coats of distemper oil emulsion over a coat of primer and putty white or tinted on wall surfaces complete all as specified and directed.

M&L for two coats of weather proof paint on newly plastered external wall surfaces incl preparation and over a coat of primer all as specified and directed

M&L for complete removal of existing treatment and preparation of of wall, washing, scrubbing down and stopping of disterpered and painted surface old plastered/ decorated surface and applaying two coat wallcare putty for smooth finished of the surface and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.

M &L for complete removal of existing treatment and preparation of wall, washing, scrubbing down and stopping of old treatment and painted surface of plastered/ decorated surface and applying cement base wall care putty and two coats of weather proof paint over a coat of primer on wall surfaces complete all as specified and directed.

M & L for Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tesile strength of 550 Mpa as in roof covering to wall, fixed with self tapping screws as specified

M &L for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, and eves board fixed with self tapping screws as specified

M&L for Preparation of Old painted surface of Steel of any description and applying one coat of synthetic enamel paint over 10cm width or girth complete all as specified and as directed.

Preparation of New Steel surface and applying two coats of synthetic enamel paint over a coat of red oxide over 10 cm width or girth.

M&L Preparation of New Wood surface and applying two coats of synthetic enamel paint over a coat of pink primer over 10cm width or girth.

Preparation of old painted wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat (finishing coat) of synthetic enamel paint all as specified

M&L providing brick work in CM 1:6 , 23 cm thick and 15cm high along external walls to fill the gap including plastering 15mm thick in CM 1:6 finished even and smooth without using extra cement.

Providing and fixing in true horizontal level 600mm x 600mm, false ceiling system hot dipped galvanised steel section, exposed surface with pre-coated capping, main tee of size 24 x38 mm, having 0.25mm gauge at every 1200 mm centre to centre maximum and rotary stitched cross tee of size 24 x 38 mm having 0.25 mm gauge at every 600mm c/c and sub cross tee of size 24 x 38mm, having 0.25 mm gauge at 1200 mm c/c and wall angle of size 19 x 19mm, having 0.35mm gauge fixed to the periphery of the wall. The abovegrid is suspended at every 1200 mm c/c in both directions using 2.0mm thick pre-straightened GI wire. laying calcium silicate fissured pattern semi perforated butt edge ceiling tiles , of size 600mm x 600mm x 6mm having thermal conductivity K=0.15 W/mOK, having fire performance (BS-476).

S&F in repair Stainless steel curtain rod/rail 25 mm dia complete all as specified & directed.

S&F in repair Stainless steel curtain rod brackets 25 mm dia including necessary stainless steel clamp complete all as specified & directed.

Taking up or down steel tubing and connections for bore of tube 15 mm, complete all as specified and directed.

Taking up or down steel tubing and connections for bore of tube 20 mm, complete all as specified and directed.

S&F of 20mm steel water tubing, medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors.

S&F of 15mm steel water tubing, medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors.

Cutting chases in brick wall built in cement mortar for concealed water tubing and making good with cement mortar in 1:4 ,cutting depth not exc 10 cm as directed.

S & F in repair Bib tap fancy type chromium plated with long shank with flange screwed for iron pipe 15mm bore, complete all as specified and directed (Make Jaquar cat part No DRC - 370370)

S&F in repairs fancy type CP bib cock for kitchen sink of 15 mm bore complete all as specified and directed (Make Jaquar cat part No APR- 101347

S&F in repairs fancy type CP two way bib cock of 15 mm bore complete all as specified and directed (Make Jaquar cat part No DRC - 37041) .

S & F in repair Chrome Plated Swan Neck Tap , for WHB fancy type cast copper alloy, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed15 mm dia bore pipe. complete all as specified and directed (Make Jaquar cat part No CON-123BKN)

S&F in Repair Stop valves/angle cock, 15mm dia pipe cast copper alloy, fancy type, chromium plated with long shank and cup screwed down, high pre-ssure, for iron pipe or for unions and fixed (Make Jaquar cat part No - FLR - 5053N)

S&F Brass chromium plated corner glass shelf with bracket complete all as specified and directed .Make-Plumber cat No.U-0918 or equivalent in Jaquar /Parco/MARC/ESS as approved by GE

S&F Sheet glass shelf assembly consisting of 5.5 mm thick glass shelf 120mm wide with chromium plted bracket gouard and railing 600 mm long Make-Plumber cat No.U-0918 or equivalent in Jaquar /Parco/MARC/ESS as approved by GE

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S & F in repairs vitreous china wash down water closet (Padestal Pattern) white/Coloured (excluding flushing cistern and flush pipe) including white/any colour PVC seat cover white closed pattern with recessed bottom and connection to drain or out going pipe and flushing pipe.

S&F in repairs 10 ltr capacity PVC Low level flushing cistern including 32mm dia PVC flush pipe, fixing in position with PVC connection pipe of 15mm x 600mm long etc complete.

S&F in repair vitreous china wash hand basin, oval type white ,flat back,size 550x400mm incl 32mm dia polythelene waste pipe and 32mm dia CP waste coupling, and incl bracket necessary packing and chain and plugs and porcelain stopper complete all as spd.

S&F in repairs kitchen sink stainless steel with draining board made of 1mm thick sheet with plugs,washer and waste including bedding in cement mortar or dwarf wall or cantiliver brackets and connectinng unions to pipe overall size 915x460mm ,bowl size 410x330mm x160mm complete all as specified and directed.

S&F Stainless steel plate rack of size 750mm x 900mm x 250mm including fixed with rawl plug and screws on walls

Dismantling water tanks and removing to store exc 250 & n. exc 1000 litres capacity

S & F Rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I 1000 litres capacity.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning and removing all scale and dirt etc and hoisting if required and re-fixing in position exc 500 & n. exc 1000 litres capacity

S&F in repair 20mm dia Ball valves,of PTMT high pressure, with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed.(Minimum weight 15 to 25mm to 142 - 455 gms)

S&F in repair 20mm dia Gun-metal, golbe or gate valves, with iron wheel head, screwd both ends or iron pipe and fixed

S&F in repair Sainless steel toilet paper holder of brass cromium plated fixed to walls with chromium plated (CP) brass screws (Make Jaquar cat part No .ACN - 1153N)

S&F in repair brass chromium plated bottle traps for wash basins with inlet and outlet screwed for connection including necessary packing, union and cup and fixed 32 mm dia bore of trap.

S&F in repairs Shower rose with brass chromium plated shower rose with or without swivel joints, 125mm size including fixing to steel pipe or union.

S&F in repairs Brass chromiun plated tubular towel rail, 20mm dia ‘D’ type, 60CM long between flanges, fixed in repair. (Make Jaquar cat part No - .ACN 1111NM)

S&F 15mm bore brass CP wall mixer for mixing hot and cold water screwed down with provision of over lead shower and cock for iron pipe and fixed complete all as specified and directed. (Make Jaquar cat part No - FUS-29273UPR)

S&F in repairs health faucet CP with connecting pipe 1 Meter long with stand (Make Jaquar cat part No - ALD - 565)

S&F in repair 18mm thick factory made PVC sheet one side prelam sheet kitchen cabinet shutter .The 18mm thick sheet shutter bent at 90 degree and finish all edges at level for making edge lipping bending for 0.5mm thick PVC sheet lipping at all four edges using bonding tape etc. Complete all as per direction of Engr-in- Charge manufactures specification.

S & F in repair Factory made PVC cabinet of required size fabricated by joining for 18mm thick PVC Celuka ply fixed with each other using solvent cement adhesive and screws and 18mm thick PVC sheet as backing of cabinet fixed with screw and solvent cement adhesive etc.

S&F in repair factory made PVC shelf /partition of required size consisting of panel of 18mm thick celuka PVC ply and for supporting the hold of shelf /partition and shall provided 3 edges in size 18mm x 18mm as per required length the front side of the edge visible in the front of the shelf / partition to be edge lipped by 18mm width x 1mm thick PVC Sheet of density 600 Kg/Cum manufactured by ISO 9001 - 2015 Cerfified campany , using solvent cement etc.complete as direction of Engr-in-Charge manufacturers specification and drawings.

S&F stainless steel self closing hinge of 75 mm size for PVC door shutter complete as specified and directed.

S&F 50 X 15 mm size magnet door catcher for closing for PVC door shutter complete as specified and directed.

S&F 100 mm long size MS mat / glossy finish handle complete as specified and dirceted.

S&F mild steel drawer cabinet channel for moving the drawer etc complete as specified and directed.

S & F modular type stainless steel basket size 24 x18 x 6 inches (dia of wire not less than 3.0mm) of any shape with side sliding roller clip and sliding rails on both side fixed with steel screws incl all fixing arranement complete as specified and dirceted.

All as per item no above but basket size 20 x18x 6 inches complete as specified and dirceted.

S & F in repair 110mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to floor/ walls etc complete.

S & F repair PVC (SWR) bends 110mm dia any radius with access door

S & F in repair PVC (SWR) junction single,(Single T) 110mm dia equal or unequal with access door

S&F in repair PVC (SWR)vent cowl 110mm bore

S&F in repair 75mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls etc complete.

S&F repair PVC (SWR) bends 75 mm dia any radius with access door

M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement etc complete, fixed in repair.

M&L Machine cut mirror polished kota stone slab flooring with rounded edge 18-20 mm thick over cement screed bed (1:6) 15mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and directed.

M&L Machine cut kota stone skirting 18-20 mm thick in riser of steps skirting, dado, and pillar over 10mm thick backing coat in cement mortar in (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding and mirror polishing complete all as specified and directed.

M&L for brick work in modular size with sub class "B" bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Excavation in trenches n exc 1.5 mtr wide and n exc 1.5m in depth for foundation in hard and dense soil

M&L for Cement concrete type D2 1:4:8 (40mm graded aggregate) in foundation filling and mass concrete.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Ditto as item No - 4 here in before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for RCC type B1 1:2:4 (20mm graded aggr) as in lintel over 1.5m span complete.

M&L for Reinforced cement concrete (Nominal Mix) Type B1 1:2:4 (using 20mm graded aggregate) in Slabs supported on walls, Beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work. Not exceeding 200mm thick (Horizondal or vertical)

Form work to sides and sofit of floor roof beams beam haunching ,girders,bressummers,lintel complete all as spd.

M&L for fair finished Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc. 20cm wide.

M&L Rendering 10mm thick on fair faces of concrete surface of ceiling in CM 1:3, surface finished even and smooth without using extra cement.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F for Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

M & L glazed ceramic coloured tiles (300x200mm)x7mm thick on vertical surfaces such as skirting, dados and risers to step etc, set and jointed in neat cement slurry and pointed in coloured cement to match the tiles including 10mm thick rendering in CM 1:4.

M&L for hardcore with broken stone aggregate of gauge n.exc 63mm deposited spread and levelled in layer not exc 15cm thick , watered and rammed to true surface.

M&L Cement concrete 1:4:8, type D2 (40mm graded stone aggregate) for 100mm thick floor as in sub base

S&F stop valve, 15 mm bore, cast copper alloy chromium plated fancy type screwed down,high pressure with crutch or butterfly hndle, screwed both ends for iron pipe or for union fixed.

S&F in Vitreous China Wash Hand Basins, size 550 X 400 mm (Flat Back or Angle Back type) including 32mm dia Brass Chromium Plated Waste Fitting and PVC connection pipe of 15mm x 600mm long,piller tap 15mm bore cast copper alloy and a Pair of Angle iron Brackets duly Painted/Erecting Stand including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S & F Vitreous china urinals, Half stall type,white complete including providing and fixing plugs,bedding urinal against wall in cement mortar 1:2,securing urinal to plugs with and including 60mm long brass screws , with grating and union for discharge pipe incl 40mm waste coupling, 375mm long pvc connection and waste pipe complete.

S & F for vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) fixed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber joints laid in trenches or in floors etc complete.

S&F PVC (SWR) bends 110 mm dia any radius

S&F PVC (SWR) Junction single (Single T) equal or un equal 110 mm dia any radius

M&L for Preparation of newly plastered surface of walls and applying three coats of white wash

M&L Preparation of Newly plastered surface and applying three coats of white wash on Ceiling.

Providing precast cement concrete louvres and jallies, 40mm thick type B0 1:2:4 ( 12.5mm graded aggregate) set in cement mortar (1:4)(mea-sured solid), including all mouldings but excluding frame

Returning, filling in including spreading, watering and well ramming in layers n. exc. 25 cm thick in hard/dense soil.

Removing excavated soil to a distance n. exc. 50 and depositing where directed at a level n. exc. 1.50 m above the starting point.

Spreading and levelling in layers n. exc 25cm thick and well ramming including watering as required.

Rotational moulded polyethene water storage tanks 500 lit capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part-I including 25mm bore Ball brass valves, high pressure, with polythene float and flynut, 20mm Tank nipple suitable for HDPE water tank, 20mm bore Gun-metal, globe or gate valves, with iron wheel head, complete all as directed by Engr-in- Charge

M & L for Non skid ceramic tiles coloured, 7 to 8 mm thick (Square / rectangular ) area of each tile exceeding 0.18 Sqm but n. exc 0.36 Sqm, over & including 20mm thick screed bed in CM (1:6) in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles as directed and specified.

M & L Preparation of newly plastered surfaces of walls and applying two coat of cement base paint all as specified.

S & F gate valves 15mm bore, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions fixed.

Excavating in post holes(or similar holes)each n exc 0.5 cum ,getting out,returning,filling in any type of soil complete all as specified and directed.

M&L for providing cement concrete 1:3:6 type C2 (40 MM Graded aggregate) as in foundation filling and mass concrete complete all as specified and directed.

S & F Steel work in tubular trusses including special shaped washer etc, complete using ERW or induction butt welded tubes confirming to IS. 1161-1979 grade St.-240.

M&L for preparation of new steel surfaces of any description ,over 10 cm width or girth and applying two coats of synthetic enamelled paint over a coat of red oxide primer complete all as specified and directed.

M&L pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self taping screw as specified

S&F 500 ltr capacity rotational moulded polyetlylene water storage tanks incl tank cover (Cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed.

M&L for providing cement concrete type C-2 (1:3:6 ) using 40mm graded stone aggregate for Base of PVC water tank etc complete all as specified and diretced.

S & F 15 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwd for iron pipe and fixed complete. Make : 'PRAYAG' or equivalent.

S & F Kitchen cabinet in Required sizes at site made out of 18mm thick one side Decorative lamination & other side balancing lamination sheet consisting of carcass 18 mm thick PVC sheet & Provision of shutters mae out of 18 mm thick one side decorattive laminated PVC sheets all required brackets 5.5 screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be cover with 2 mm thick edge bonding tape or 90 Degree edge bent finish as per make and Specification mentioned as per drawing and specification approved by Engg-in-charge

M & L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement etc.

Taking down carefullycopper/aluminium point wiring (light, fan, socket or power) complete with fittings such as switches, sockets ,ceiling rose, light fittings etc, and making good the disturbed surface of walls and floors etc all as directed by Engr-In-Charge.

Taking down carefully copper/aluminium sub-main wiring any type and making good the disturbed surface of walls and floors etc all as directed by Engr-In-Charge.

Taking down carefully MCB DBs/sheet metal earth plug socket any size and any type including MCBs any type and making good the disturbed surface of walls and floors etc all as directed by Engr-In-Charge.

M&L for Point wiring in repairs including with PVC insulated FR PVC unsheathed electric cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area for phase/neutral in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good disturbed surface of wall (cutting except on ceiling for fan point only, on ceiling instead of pvc conduit surface casing caping will be used) & 1.5 sqmm green FR PVC insulated unsheathed copper conductor as a earth wire connected to earth dolly by providing lugs including galvanised boxes etc for the following :-

(a) One light/fan/bell point controlled by one switch

(b) One 5amps socket out let point controlled by one switch on same board with other switches.

(c) One 5amps socket out let point on independent board controlled by one switch.

All as per item no 5 here in before but using pvc insulated unsheathed 2.5 sqmm cross sectional area cable for phase /neutral & for earth 2.5 Sq mm green PVC insulated cable for 15 amps socket point on independent board controlled by one switch.

Supply and fix in repairs Modular Switch flush type 10 Amps single pole, one way complete all as specified. Make:- Legrand Mylinc Series, Crabtree Athena Series, Anchor ROMA PLUS

Supply and fix in repairs Modular Socket outlet, multi purpose, 5 Pin combined 6 Amps flush type complete all as specified. Make:- Legrand Mylinc Series, Crabtree Athena Series, Anchor ROMA PLUS

Supply and fix in repairs Modular Bell push flush type, 10 Amps complete all as specified. Make:- Legrand Mylinc Series, Crabtree Athena Series, Anchor ROMA PLUS

Supply and fix in repairs Modular Socket outlet, multi purpose, 2/3 pin combined 16 Amps universal socket complete all as specified. Make:- Legrand Mylinc Series, Crabtree Athena Series, Anchor ROMA PLUS

Supply and fix in repairs Modular Switch 16 Amps single pole, one way complete all as specified. Make:- Legrand Mylinc Series, Crabtree Athena Series, Anchor ROMA PLUS

Supply & fix in repairs modular fan regulator step type, 2 module type complete. Make:- Legrand Mylinc Series, Crabtree Athena Series, Anchor ROMA PLUS

Supply and fixing in repairs white finished single mounting modular plates sutable for modular accessories of following sizes:(Make:- Legrand Mylinc Series, Crabtree Athena Series, Anchor ROMA PLUS).

(a) Sutable for 1/2 modules

(b) Sutable for 3 modules

(c) Sutable for 4 modules

(d) Sutable for 8 horizontal modules

Supply and fix in repairs sheet metal boxes concealed in wall suitable for housing modular accessories of following sizes :-(Make:- Legrand Mylinc Series, Crabtree Athena Series, Anchor ROMA PLUS).

(a) Sutable for 1 or 2 modules 50mm.

(b) Sutable for 3 modules 50mm.

(c) Sutable for 4 modules 50mm.

(d) Sutable for 8 modules 50mm.

Supply and fix in repairs Bell, ding dong type, AC 230 Volts, single pole complete.

S&F in repairs ceiling rose surface bakelite three terminal complete all as directed.

S&F in repairs lamp holder insulated body with back plate for batten fittings complete all as directed.

Supply and fix LED bulb of 7 watt, Of base B-22, suitable for fixing in lamp holder.

Supply and fix in repairs LED batten for retrofit type LED tube upto 1x22 Watt, without LED tube rod,pre-wired for LED tube, complete with all accessories duly connection with three core flexible copper cable and duly fixed on two Nos PVC square boxes complete all as specified and directed.

Supply and fix in repairs retrofit LED tube light T-8 type, 1x20/21 Watt, 6000K with extruded Al heat sink for efficient heat dissipation complete all as specified and directed.

Supply and fix in repairs LED tube light fittings 1x9/10 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of pvc square boxes complete all as specified and directed.

Supply and fix in repairs Wall light fittings suitable for & including LED bulb of 7 watt, including connection with all necessary fixing accessories complete all as specified and directed by Engr-in-Charge. Make :- Havells Cat No. LHDL07150099 or equivalent in equivalent in Bajaj, Philips.

Supply & fix plastic body exhaust fan, AC single phase 230/ 240 V of size 250 mm sweep with louver ,white in colour including cutting of wall and duly connection with copper wire from ceiling rose etc complete all as specified and directed. Make: Havells Model Ventil Air-DX White or equivalent in Crompton/Almonard

M&L in repairs for Sub main wiring in repairs with two runs of single core PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in and including concealed non metallic rigid PVC conduit of not less than 25 mm dia including one run of PVC insulated unsheathed 6.0 sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly in concealed wiring system by cutting of wall and making good disturbed surface of wall all as specified and directed.

M&L in repairs for Sub main wiring in repairs with two runs of single core PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in and including concealed non metallic rigid PVC conduit of not less than 25 mm dia including one run of PVC insulated unsheathed 4 sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly in concealed wiring system by cutting of wall and making good disturbed surface of wall all as specified and directed.

S & F in repair TPN DB with provision for MCB TPN as incomer and SP MCBs as outgoing made of steel sheet phosphatised powder coated with bus bar, neutral link earth bar and DIN Rail having IP 42-IK 09 with metal door capacity 4ways 415 V, connection with aluminium/copper lugs including civil/plastering work for make up good the disturbed surface matching with existing surface complete all as directed.

S & F in repair MCB TPN 4- Pole 63 amp, 415 volts, 'C' series' 10 KA breaking capacity & connection complete.

Supply and fix in repairs double door SPN DBs eight ways of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete..

S & F in repairs MCB SPN 6 to 32 amps 10 KA, 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed.

S & F in repairs MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed.

S & F (in building peripheri) energy efficient, compact street lighting 25 Watt LED with deep drawn Alluminium housing complete with conncting wire and provision of GI bracket, clamp, nuts, bolts grounded in wall incl all fixing arrangement.

Supply & fix metallic exhaust fan AC single phase 230/ 240 V of size 380mm sweep with louver including cutting the existing wall for making a hole of appropriate size for fixing the exhaust fan and making good the disturbed surface complete duly connection with copper wire etc completeincl taking down of ceiling fan in safe custody and deposit to E/M Store all as specified and directed by Engr-in-Charge. . Make: Havells Model Turbo Force SP or equivalent in Crompton/Almonard

Supply and fix electric ceiling fan capacitor type 1200mm sweep, 230 Volts single phase, ISI marked,Energy efficient, white in colour, complete with all accessories like down rod,clamps,and connection from ceiling rose, etc incl taking down of ceiling fan in safe custody and deposit to E/M Store all as specified and directed by Engr-in-Charge.

Supply and lay XLPE insulated armoured heavy duty electric cable with stranded aluminium conductor 1100 Volts grade of size 16 sq mm 4 core, cross sectional area lay trenches/wall/poles/ducts/pipes or through sleeve etc including connecting/jointing with lugs and testing all as specified and directed by Engineer-in-Charge.

Excavating in trenches, in any type of soil not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc and getting out in any type of soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, leveling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply laying and jointing GI pipe 'light grade' 40 mm bore in trenches/under floors or roads/ along poles/ on wall incl clamps for protection of cables incl fittings complete all as specified and directed.

M & L for clean and dry sand (un-washed) in trenches incl spreading and levelling for cushioning of UG cable complete all specified and directed.

M & L for brick size sub class ‘B’ (modular size), laid flat in trenches for protection of cable complete all as specified and directed.

M & L for earthing complete with galvanised steel earth p;ate 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanised Iron Wire of size 4 sq mm as earthing lead by means of bolts, nuts, cheek nut and washers of galvanised iron or steel besides at all joints as shown in Electrical Plate No-3 of SSR Part I and including excavation and earth work GI pipe 20 mm dia light grade protection pipe and including chorcoal filling common salt ,PCC 1:3:6 type CI using 20 mm graded stone aggregate chamber and MS angle iron frame 40x40x6mm and RCC cover 40mm thick (1:2:4) type B-1 using 20mm dia graded stone aggregate reinforced with 6mm dia round bars @ 75 mm c/c both ways with MS handle 12mm dia, CI funnel and wire mesh 20mm dia GI pipe medium grade for watering and connected to earth Test point (Including testing complete all as specified and directed).

M & L for Point wiring including with PVC insulated FR PVC unsheathed electric cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area for phase/neutral in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good disturbed surface of wall (cutting except on ceiling for fan point only, on ceiling instead of pvc conduit surface casing caping will be used) & 1.5 sqmm green FR PVC insulated unsheathed copper conductor as a earth wire connected to earth dolly by providing lugs including galvanised boxes with bakelite sheet for mounting switches, sockets, fan regulators etc for one light/fan point controlled by one switch.

S&F switch piano flush button single pole one way 5 Amp 240 volt complete as directed.

S&F ceiling rose surface bakelite three terminal complete all as directed.

S&F lamp holder insulated body with back plate for batten fittings complete all as directed.

S&F LED lamp of 7 W 6500K complete all as directed. Make: Crompton/Wipro/Havells

Supply and fix integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 or equivalent in Crompton/Wipro

Supply & fix metallic exhaust fan AC single phase 230/ 240 V of size 300mm sweep with louver including cutting the existing wall for making a hole of appropriate size for fixing the exhaust fan and making good the disturbed surface complete duly connection with copper wire etc complete all as specified and directed. Make: Havells Model Turbo Force SP or equivalent in Crompton/Almonard

Supply and fix single door SPN DB eight ways of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed by Engr-in-Charge.

Jamna Constructions

SANJAY ENTERPRISES