Special repair for renovation of Sub Health Centre at village Kalheri (Gharaunda) in Karnal Distt.

Amount

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres.(HSR 6.6)

Dismantling brick work, tile masonry or tile lining and tile terracing . (b) in cement,[HSR 8.5(b)]

Scrapping white wash and colour wash [HSR 8.32(a)]

Scraping of cement plaster [HSR 8.32(c)]

Cement Concrete 1:4:8 with stone aggregate 40mm nominal size in foundation and plinth. [HSR 10.39]

Cement Concrete 1:1½:3 with stone aggregate 20mm nominal size in first storey upto 4 meters above plinth level. [HSR 10.60]

Cement concrete 1 : 1½ : 3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respects. [HSR 10.82 + 10.95 (a)]

Providing and laying 60mm thick interlocking paver blocks of all shapes and colours in design mix cement M-35 ovar a bed of 25mm thick fine sand complete in all respect. [HSR 10.158]

First class brick work laid in cement sand mortar 1 : 6 in foundation and plinth (HSR 11.2)

Terracing consisting of tiles 22.86 cm x 11.43 cm x 3.81cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and an other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 Kg. per sqm on top of RCC the slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13).

Providing and fixing PVC rain water pipe 6 Kg. Pressure of ISI mark in cement mortar during masonry work. a) 100mm dia PVC pipe 6 Kg. pressure. (HSR 13.89 a)

b) 150mm dia PVC pipe 6 Kg. pressure. (HSR 13.89 b)

Providing & fixing PVC bend ISI mark. a) 100mm dia PVC Bend. (HSR. 13.90 a)

b) 150mm dia PVC Bend. (HSR. 13.90 b)

Providing & fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92) b) Size of ceramic Glazed tiles 300 x 450 mm

12 mm thick cement plaster 1 : 4 on walls ( HSR 15.5 )

12 mm thick cement plaster 1:6 on walls [HSR 15.7]

15mm thick cement plaster 1:4 on the rough side of single or half brick wall. (HSR 15.10)

15 mm thick cement plaster 1:6 on rough side of single or half brick wall (HSR 15.12)

Preparation of ply wood surface for painting inlcuding sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. Painting on wooden surfaces etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.1)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.2).

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3).

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surface. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.25).

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58).

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)].

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc.,(non-coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln seasoned), with 100 mm wide vetical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete, fixed in position (execluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) [HSR 17.90 (b)(-)Note (i) under item No. 17.18] b) 35 mm thick.

Factory manufactured panelled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash etc.(non-coniferous timber other than teak, conforming to I.S. specification No.1003, kiln seasoned), with 100mm wide vertical styles, 150mm wide lock rail, 200mm wide bottom rail and 100mm wide other rails, with panels of 12mm thick commercial veneered both sides particle board of plywood of B.W.R. grade, hot-pressed, including cost of iron hinges, screws, chocks/cleats, stops and nails etc. complete fixed in position(excluding the cost of any fittings, other than specified above but including labour for fixing the same in position:- a)30mm thick (HSR 17.91(b)(-)Note (i) under item No. 17.18]

Factory manufactured wire gauze door and window shutters of commercial hard wood, such as hollocks, champ, chikrassy and chaplash, etc., (non-coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln seasoned), with 100 mm wide vetical styles, 150 mm wide lock rail, 200 mm wide bottom rail and wire gauze of 140G or 120G designation including cost of iron hinges, screws, chocks/cleats,stops, nails etc., complete fixed in position (execluding the cost of any fittings, other than specified above but including labour for fixing the same in position) [HSR 17.92 (-)Note (i) under item No. 17.18] ii) 35 mm thick.

Steel reinforcement TMT bars FE-500 FQR /FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending vinding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/storeys/basements etc. (HSR 18.22)

Pressed steel sheet frames (chowkats ), consisting of 2mm thick steel sheet of the specified section,including iron lugs(hold fasts) iron hinges conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for fillings in the frame, and cement concrete 1:3:6 for lugs complete (HSR 18.34) c) Door and Window frame of size 127 mm x 50 mm with 40 mm wide double rebate

Preparation of sub grade, including trenching, rough dressing of spoil, final dressing of earth, to given levels and camber, watering rolling with road roller, and compacting the bed. [HSR 24.1] LR

Providing and fixing in position best indian make (as approved by the Engineer-in-charge) European type water closet suit, Syphonic type, consisting of- (i) Vitreous China Ware Syphonic Suite with 15 Liters capacity matching chinaware cistern and all internal brass fittings complete with ‘P’ or ‘S’ trap with or without vent (as approved by the Engineer-in-charge). (ii) One Piece seat and lid in hollow black or white with plastic fitted with chromium plated hinges and rubber buffers,(to the approval of the Engineer-in-charge). Complete in all respects including cutting and making good the walls and floors [HSR 30.5] a) Single trap syphonic W.C. Suite (i) White

Extra over item Nos. 30.3 to 30.6 for providing and fixing best Indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid. [HSR 30.13 (i)] White plastic seat (Solid)

Providing and fixing in position best Indian make large flat back or Angular lipped front Urinal 610MM High consisting of. (i) Flat back lipped or angular urinal basin or VITEROUS CHINAWARE ; (to the approval of the Engineer-in-charge) (ii) 5 LITRES CAPACITY mosquito proof INDIAN MAKE C.I. AUTOMATIC flushing CISTERN painted with non-yellowing white enamel paint or other approved shade enamel paint on outside and superior black bitumastic paint on inside with screwed 15mm pipe : (iii) PAIR OF R.S.OR C.I.PAINTED BRACKETS AND BRASS CCOUPLINGS :- (iv) Pair of C.I. SPECIAL TYPE BRACKETS for urinal : (v) 32 MM C.P.BRASS WASTE WITH DOME GRATING; (vi) 32 MM C.P.BRASS SPREADER : COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOOR AND PAINTING OF FITTINGS ETC. (as required by the Engineer-in-charge). [HSR 30.25] White

Providing and fixing in position best Indian make (ordinary)lavatory suites, consisting of Lavatory in vitreous chinaware size as given below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary. R.S. or C.I. Brackets for building into wall including painting, 32mm C.P. brass waste with C.P brass chain and rubber plug, 15mm C.P. brass screw down pillar tap with jamnuts or couplings best design (as approved by the Engineer-in-Charge). All fittings best Indian make and; to the approval of the Engineer-in-Charge. All brass work chromium plated and complete in all respect including cutting and making good the walls floors and painting of fittings etc. [HSR 30.41] White (iv) Size 550mm x 400mm with one no. tap.

Providing and fixing in position best Indian make Pedestal fittings of Vitreous chinaware complete (as required by the Engineer-in-charge) [HSR 30.44] (i) White

Providing and fixing in position best quality stainless steel sinks with complete fittings as fully described in item No.30.51 above [HSR 30.53] (a) size 600mm x 450mm x 200mm

Providing and fixing in position 15mm i/d C.P.brass & bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75] (i) bib cock long body

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in-charge). [HSR 30.76] 15mm stop cock (i) Stop cock male and female end

(ii) Concealed stop cock with flange

Providing and fixing in position automatic brass ball valves in tanks [HSR 30.110] WITH PEASTIC BALL (ii) 20mm i/d

Providing and fixing HDPE water storage tanks of Sintex, Diplast, O.K., Supreme make with covers / lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with sutiable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-Charge. (except civil work). (HSR 30.119) 1000 Ltr. capacity.

Providing and fixing position gully traps fixed in cement concrete 1:4:8 complete with H.C.I. grating 150mm x 150mm cast iron cover weighing approximately 7.26 Kg. and frame clear opening 300 mm x 300 mm and outside size 330 mm x 330 mm and chamber including cost of all brick work in cement mortar 1:5 cement concrete 1:8:16 in foundations and cement concrete 1:2:4 in coping around C.I. cover and frame etc. with three coats of black bitumastic superior PAINT of approved manufacture on all C.I. workas per standard design minimum depth of water should be 150mm with a minimum seal 50mm. [HSR 30.114] (iii) 150 mm internal diameter S.W. gully trap

Construction brick masonray inspection chamber sizes as given below upto 0.60 metres average depth in cement mortar 1:5 lime concrete with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 benching 12mm thick cement plastern 1:2 with a floating coat of 1 mm thick of neat cement RCC 1:2:4 slab 100mm thick/C.C. topping 50mm thick with 455 mm x 455 mm / 455 mm x 610mm inside light duty C.I inspection chamber cover and frame weight as per I.S.I specification painted with 3 coats of black bitumastic superior paint complete as per standard design. [HSR 29.84] (c) Size 600 mm X900 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with R.C.C. slab)

Providing for laying, jointing, fixing and testing G.I. (Medium class "B" type of Tata & Jindal make) pipe lines and specials tees bends, sockets, elbows etc. inside building and testing etc. complete including cutting threading. Including cost of Special. G.I. specials shall be of Make:- UNIK, TATA, ZOLOTO. (NS) (i) 15 mm internal diameter of pipeline

(ii) 20 mm internal diameter of pipeline

Providing for fixing and jointing union couplings in G.I. and W.I. pipelines. [NS]. (a) 15 mm internal diameter

(b) 20 mm internal diameter

Providing, fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I. pipelines laid in the ground or inside building including cartage from divisional stores or nearest railway station to site of works. (NS). (b) 20 mm internal diameter Note:- 1. In case of any difference in the unit & nomenclature of any of the HSR Items of Civil, P.H. work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable. 2. Only reputed make material will be used (make/brand exhibited in HSR and exhibited in approved standard document) as approved by Engineer-in-charge, while executing various items/works at site.

The Quality Coop Society Ltd

The Adhmi Coop Society Ltd