REPAIR TO PLASTERING, FLOORING, CHEQUERED TILES, RCC CHAJJA, BRICK WORK, PLUMBING, SANITARY FITTINGS, ROOF TREATMENT AND REPAIR TO SEWAGE LINE, MANHOLES, SEPTIC TANK, SOAK WELL ETC AT ADRDE AGRA UNDER GE I RnD DELHI

Amount

Taking down cement plaster on brick/ stone walls etc any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick plaster on any faces of brick work in CM1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15 mm thick plaster on fair faces of brick/concrete surfaces as in CM 1:4 mixed with WPC finished surface even and smooth complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for rendering 15mm thick on fair faces of brick/stone or concrete surfaces in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick plaster on concrete surfaces of ceiling in CM 1:3 and finished the surface even & smooth complete all as specified and directed.

M&L for preparation of newly plastered ceiling surface and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of oil bound distemper over a coat of 2mm thick wall care putty (in two layer of minimum 1mm thick in one layer) complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of exterior emulsion paint over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls brooming down smoke, soat or efflorescent salts and applying one coat of oil bound distemper complete all as specified and directed.

M&L for preparation of old surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for complete removal of the existing treatment on walls and applying two coats of white wash complete all as specified and directed.

M&L for complete removal of the existing treatment of walls and applying two coats of oil bound distemper over a coat of 2mm thick wall care putty (in two layer of minimum 1mm thick in one layer) complete all as specified and directed.

All as per item Ser No 12.00 above but two coats of exterior emulsion over a coat of primer.

M&L for preparation of old painted wood and wood based surface of any description not otherwise discribed over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for one coats of synthetic enemel paint on old painted steel surface of any description over 10cm width or girth including preparation of surfaces complete all as specified and directed.

Supply only intergral water proofing compound complete all as specified and directed.

S&F in repair mild steel work as in framed brakets of angles or tees with web and flanges out to shape, drilled and counter sunk for screw, including bending and welding angles as necessary gusset plates, riveting etc n.exc. 10 Kg each bracket conferming to Fe-410 or FE-310-0 complete all as specified and directed.

M&L in repair for 40 mm thick sand stone slabs in shades, Chajjas, shelves etc n.exc 2m length, Punched dressed on face and along exposed edges self faced on other side and set in cement mortar 1:4 and pointed in CM 1:2 including taking down/dismantling old unserviceable stone slab complete all as specified and directed.

M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting exceeding 20cm girth (Brick walls) complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) and making good the disturbed surface, area not exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames area exc 1.5 Sqm but not exc 4 Sqm each with shutters (without taking off shutters from the frames) and making good the disturbed surface complete all as specified and directed.

Taking down shutter of any descriptions area exc 1 Sqm but not exc 2 sqm each complete all as specified and directed.

Refixing shutter in same opening area exc 1 Sqm but not exc 2 sqm each complete all as specified and directed.

S&F Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc.complete all as specified and directed.

All as per item Ser No. 24.00 above but size 125x60mm.

M&L for 35mm thick 2nd class hard wood factory made plain framed panelled shutter (any number of panels), with lock rail and panel of 12mm thick BWP veneered particle board with commercial veneering on both faces. The sizes of rails and stiles as per IS:1003 (Part -I) Kiln seasoned and chemically pressure treated fitted to chowkhats complete all as specified and directed.

M&L for 35mm thick 2nd class hard wood factory made glazed and skeletan shutters open rebated and prepared to receive glass or gauge etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers provided with stiles and rails complete all as specified and directed.

M&L for 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M&L in repair 18/19 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in cupboard shutter complete all as specified and directed.

S&F factory made steel windows with side hung shutters glazed or gauged including projection type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welding complete all as specified and directed.

S&F factory made steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed.

S&F in repair framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Grade E-165 complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing shown in SSR complete all as specified and directed.

S&F factory made PVC door frames of size 50mmx47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suitable for opening as per site condition compete all as specified and directed.

S&F in repair continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) in 30 mm complete all as specified and directed.

S&F 300 mm MS ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F in repairs 300 mm MS ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F 100mm stainless steel butt hinges, medium weight, cold rolled stainless steel, and fixed complete all as specified and directed.

S&F 300 mm long aluminum alloy, anodised sliding door bolts, plate type, and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 250 mm long aluminum alloy, anodised sliding door bolts, plate type, and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy complete all as specified and directed.

S&F in repairs 250 mm long aluminum alloy, anodised sliding door bolts, plate type, and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

All as per item Ser No 42.00 above but 100 mm size.

S&F in repairs 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm long aluminium handles, fabricated type, D shape, anodized and fixed complete all as specified and directed.

S&F in repairs150 mm long aluminium handles, fabricated type, D shape, anodized and fixed complete all as specified and directed.

S&F 150mm long extruded brass handles, fabricated type polished fixed in cup boards complete all as specified and directed.

S&F 140 mm long floor door stopper aluminium alloy body and tongue, anodized with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F in repairs140mm long floor door stopper aluminium alloy body and tongue, anodized with hard drawn steel spring fixed in floor complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and directed.

S&F 3mm thick Sheet glass ordinary quality and glazing with oil putty in square not exe 0.5 Sqm in each pane complete all as specified and directed.

S&F 4mm thick figured glass, pin headed type and glazing with oil putty in square not exceeding 0.5 Sqm each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description over 10 cm in width or girth, including preparation of surfaces complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description over 10 cm in width or girth, including preparation of surfaces complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L 100mm thick PCC 1:2:4, type B-1 (20 mm graded stone aggregate) including necessary form work as in path, passages, etc, surface finished even and fair & Spike rolling to surfaces or making impressions of expanded metal while the concrete is green complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in plinth protection complete all as specified and directed.

Dismantling floor, hearth wall tiling including cement mortar bedding (but not backing) including removing rubbish off the premises complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) in floor etc complete all as specified and directed.

M&L for Ist quality Non Skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exc 0.11 Sqm but n. exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for Ist quality glazed ceramic coloured tiles of size 300x200x6mm thick on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for Ist quality Non Skid ceramic coloured tiles 7mm to 8mm thick, area of each tile exc 0.18 Sqm but n. exc 0.36 Sqm over and including 15mm thick screed bed in cement mortar 1:6 laying in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

M&L for Ist quality glazed ceramic coloured tiles in vertical surfaces 450x350x7mm thick set jointed and pointed in white cement or coloured cement to match the shade of tiles over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Dismantling of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aporans etc complete all as specified and directed.

M&L for 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade laid over and including 20mm thick in CM 1:4 complete all as specified and directed.

M&L for Kota stone slab flooring 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) laid over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for Kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar etc laid over and including 20mm thick screed bed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Demolition of brick or concrete tile (laid flat or on edge) laid dry in floor, channel, kerb, apron etc complete all as specified and directed.

M&L for coloured chequered cement concrete tiles 25cm x 25cm x 22mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 40 mm thick brick tiles laid over 15mm thick screed bed in CM 1:6 and joints, grouted flush in cement mortar 1:3 mixed with 5% of crude oil by weight of cement complete all as specified and directed.

BLANK

Complete removal of existing roof treatment in up to depth of original roof slab and removing entire rubbish off the premises, and applying Water proofing treatmnet as under:- (a) Rendering 10mm thick in CM (1:4) mixed with water proofing compound @3% by weight of cement. (b) Applying a coat of approved bituminious primer @0.25 ltr/Sqm and allow to dry. (c) Applying one coat of hot blown bitumen grade 85/[email protected]/Sqm. (d) Supplying and laying polymeric water proofing membrane of weight not less than 3Kg/Sqm (e) Applying a coats of solar reflective bituminious aluminium paint @0.15 kg/sqm over the memberane complete all as specified and directed. Note: WPC shall be measured and paid seperately.

M&L for PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in padding bed plates or mass concrete complete all as specified and directed.

Taking up or down steel water tubing and connections 15mm bore complete all as specified and directed.

All as per item Ser No 76.00 above but 20mm dia.

All as per item Ser No. 76.00 above but 25mm dia.

S&F on walls/ceiling or laying in floors, 25mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings complete all as specified and directed.

S&F on walls/ceiling or laying in floors, 20mm CPVC dia CPVC pipes SDR 11& plain CPVC SDR 11 fittings complete all as specified and directed.

S&F in repair 20 mm ball brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair 15 mm bib taps cast copper alloy, chromium plated fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 15 mm Stop valve cast copper alloy, chromium plated fancy type long shank concealed type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair 15 mm bib taps standard of PTMT, any colour, high pressure screwed for iron pipe and fixed ( minium weight 15mm - 90gms) complete all as specified and directed.

S&F in repair 15 mm stop valve of PTMT, any colour, high pressure screwed for iron pipe and fixed (minium weight 15mm - 90gms) complete all as specified and directed.

S&F in repairs vitreous China squatting pan, Orissa pattern, size 580x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) but including 110mm PVC (SWR) WC connector with lip ring and PVC (SWR) P/S trap 110 mm complete all as specified and directed.

S&F in repairs Vitreous china wash down water closet pan (Pedestal pattern), white (excluding fixing bolt) etc complete all as specified and directed.

S&F in repair Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinge device complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of capacity 10 litre ISI marked complete with inlet ball valve, and handle including bracket complete all as specified and directed.

S&F in repairs vitreous china wash hand basin, white flat back, size 630x450mm excluding tap etc but including brackets complete all as specified and directed.

S&F 40 mm bore low density polyethylene pipe of pressure rating 6Kgf/sqcm complete all as specified and directed.

S&F 40 mm bore low density polyethylene pipe with waste coupling for sink complete all as specified and directed.

S&F 32 mm bore low density polyethylene pipe with waste coupling for wash hand basin complete all as specified and directed.

S&F in repair 15mm bore pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot and cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm bore pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed (minium weight - 120 gms) complete all as specified and directed.

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20mm bore weight 210 gms complete all as specified and directed.

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 15mm bore weight 142 gms complete all as specified and directed.

S&F in repairs Stainless steel sink with drainage board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915x460mm and bowl size 410mm x330mm x 160mm complete all as specified and directed.

S&F in repairs Stainless steel sink, without drainage board made out of 1.00 mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 495x420mm bowl size 410mm x310mm x 160mm complete all as specified and directed.

S&F in repair chromium plated shower rose, 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair towel rail 600 mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 190gm) complete all as specified and directed.

S&F in repair grating square 150 mm size of PTMT (minimum weight 100 gms) complete all as specified and directed.

S&F grating doom 150 mm dia with waste hole of PTMT (minimum weight 100 gms) complete all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair 32mm waste coupling of PTMT (half or full threaded) minimum weight 45 gms for urinals complete all as specified and directed.

S&F in repair 40mm waste coupling of PTMT (half or full threaded) minimum weight 45gms for sink complete all as specified and directed.

S&F in repairs PVC 75mm (SWR) floor trap, plane with grating including jointing with solvent cement complete all as specified and directed.

Taking down AC/PVC rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and directed.

S&F for 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed.

All as per item Ser No 110.00 above but 75mm bore.

S&F 75 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 110 mm dia PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed.

S&F 75 mm dia PVC (SWR) vent cowl complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins arches, pillars etc complete all as specified and directed.

M&L for brick work with sub class 'B' Old size bricks straight or cruved on plan exc 6 m mean radius built in CM 1:4 complete all as specified and directed.

M&L for cutting holes into or through brick walls built in cement mortar and walls of cement concrete and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B1 as required (superficial area not exc 150 Sqcm) complete all as specified and directed.

M&L for brick work with subclass ‘B’ old size bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

S&F in repairs stainless steel plate rack of size 600x750x250 mm of approved pattern and design complete all as specified and directed.

S&F in repair stainless steel 25 mm dia rails, fixing on decorative brackets etc complete all as specified and directed.

Supply only stainless steel decorative/aluminium brackets for stainless steel pipe 25 mm dia complete all as specified and directed.

Supply only stainless steel and finial for stainless steel pipe 25 mm dia complete all as specified and directed.

M&L for rotational moulded polyethylene water storage tank, triple layered, 500 litres capacity (cylindrical vertical with closed top) hoisted in position including dismantling of existing water tank and remove from site complete all as specified and directed.

Cleaning of sewage pipe line of any dia and depth by rodding and water pressure and cleaning of sewage line from manhole to manhole complete by mechanical means or manually complete all as specified and directed.

Cleaning of manhole upto 1.5 m deep and taking out sludge, night soil, mud, silt and other foreign material to any form by any means and removing the same outside MoD land to a distance exc 10 KM away and buried under ground and sprinkling lime complete all as specified and directed.

Cleaning desilting and emptying of existing septic tanks by mechanically including taking out sludge and other foreign materials and removing the same to outside MoD land to distance exc 10 KM away and buried under ground and sprinkling lime complete all as specified and directed.

Dewatering of sludge water from septic tank, soak wells, manholes etc including loose liquid meet ash grease, and fiber & vegetations etc by means of mechanically power transport under faul conditions and removal of sludge/debris exc 500m & not exc 1 KM and buried under ground and sprinkling lime complete all as specified and directed

Cleaning of blocked trap in kitchen/bathroom/WHB/sink/ Urinal etc by rodding or manually effected upto 1st manhole including kept work site clean and tidy complete all as specified and directed. Note for ser item No. 125.00 to 129.00 (i) Rate also includes for necessary tools and plants which is required to carryout the cleaning works ie. Cleaning rod, bucket, bamboo sticks, kasha etc. (ii) One supervisor shall take complaint from complaint cell/JE concerned & deploy required safaiwala to execute the work on daily basis. (iii) Complaint shall be completed on same day. In case the complaint is not completed on the same day, a penalty of Rs, 200/- per complaint shall be recovered from the payment of contractor. (iv) Necessary complaint register and printed machine numbered complaint slip as per specimen given by the Engineer-in-Charge shall also be provided by the contractor. (v) After completion of complaint, complaint slip shall be signed by the user and re-submitted to the concerned JE/Engineer-in-Charge. (vi) Sewage safety norms shall be strictly followed. (vii) Sludge shall be removed from site in covered vehicles only.

Excavation in trenches n.exc 1.50m wide and n.exc 1.5 M in depth and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches not exc 1.50 m wide and exc 1.5 M but not exc 3.0 m depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including, leveling, watering and well ramming in layers not exc 25cm thick each complete all as specified and directed.

Removing excavated material to a distance not exc 50 M depositing where directed at a level not exc 1.50 m above the starting point complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mmm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) cast insitu as in coping/benching including necessary form work complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in surface channels & drains complete all as specified and directed.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred stopped ends etc complete all as specified and directed.

Demolition of reinforced cement concrete (reinforced cut as required to facilitate to demolition) of any description and in any portion not otherwise described complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab for manholes septic tanks etc including necessary form work and set in CM 1:6 complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

M&L for 10mm dia TMT bar and over cut to length, bent to shape required, including cranking, bending and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in bed to drain pipe 150 mm dia including packing under and haunching against the pipe after they are laid including necessary formwork complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2, (using 40 mm graded stone aggregate) as in bed to drain pipe 100 mm dia including packing under and haunching against the pipe after they are laid including necessary formwork complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar for 100 mm dia pipe complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar for 150 mm dia pipe complete all as specified and directed.

M&L for salt glazed stoneware drain pipes 100 mm dia (internal) grade ‘A’ laid in trenches and jointed complete all as specified and directed.

M&L for salt glazed stoneware drain pipes 150 mm dia (internal) grade ‘A’ laid trenches and jointed, complete all as specified and directed.

M&L for cutting in to existing manholes for connecting new drains pipe internal dia 100 mm and making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or ¾ sec) in PCC 1:2:4 type B-1, smooth finished, and reforming benching as required complete all as specified and directed.

M&L for cutting in to existing manholes for connecting new drains pipe internal dia 150 mm and making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or ¾ sec) in cement concrete 1:2:4 type B-1, smooth finished, and reforming benching as required complete all as specified and directed.

S&F in repair PVC (SWR) floor trap of dia 75 mm with grating, including solvent cement and fixed in position complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

rohan traders

deva engineers

M/S RADHEY GOVIND ENTERPRISES

m/s meetu enterprises

Sree Ram Enterprises