Construction of Cultural Center At Sarbananda Singha Nagar Borguri (All Assam Matak Yuba- Chatra Sanmilan), Tinsukia (Assam)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2.8.1 All kinds of soil.

Providiing and laying in position cement concrete of specified concrete of specified grade exlcduing the cost of centering and shuttering - All work up to plinth level 4.1.5 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived form natural souurces)

1:5:10 (1 cement: 5 coarse sand (zone-III) derived from natural sources: 10 graded stone aggregate 40 mm nominal size derived from natural sources) Under floor

Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1 Foundations, footings, bases of columns, etc. for mass Footing

Columns, Pillars, Piers, Abutments, Posts and Struts Column

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick Chajja

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 5.1.2 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.5.22.6 Thermo- Treated bars of grade Fe- 500D or more

Supplying and filling in plinth with sand under floors, including watering, ramming consolidating and dressing complete

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement: 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.2 Cement mortar 1:4 (1 cement:4 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Kiln seasoned and chemically treated Sal wood.

Providing and fixing ISI marked flush door shutters conforming to 15: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate 2 sections and other sections of approved make conforming to 15. 733 and 15: 1285, fixing with dash fasteners of required dia id size, including necessary filling up the gaps at junctions, le at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required Including cleat angle, Aluminium snap beading for glazing/paneling, C.P.brass /stainless steel screws, all complete as per architectural drawings and the directions of Engineer in-charge. For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the costof EPDM rubber/neoprene gasket required 21.1.2.1 Anodised aluminium (anodised transparentor dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge (Cost of aluminium snap beading shall be paid in basic item):11.05 With flout glass panes of 5.0 mm thickness (weight not less than 10kg/sqm)

Providing and fixing M.5. grills of required pattern in frames of windows Metz with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 9.48.2 Fixed to openings/wooden frames with rawl plugs screws etc.

Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 11.3.1 40 mm thick with 20 mm nominal size stone aggregate

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mor more (thickness to be specified by the manufacturer), of 1st quality conforming to 15: 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm Thick Cement Mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry@ 3.3 kg/sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of step sand dados, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. sqm 1063.45

12 mm cement plaster of mix: 13.1.2.1:4 (1 cement: 4 fine sand

15 mm cement plaster on the rough side of single or half brick wall of mix 13.2.2.1:4 (1 cement: 4 fine sand) sqm 324.30

6 mm cement plaster of mix: 13.16.1 1:3 (1 cement: 3 fine sand Ground floor celling 1st floor Chajjas

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 I cement: 3 coarse sand), finished with a floating coat of neat cement. 11.6.1 18 mm thick

Finishing walls with water proofing cement paint of required shade work New work (Two or more coats applied @ 3.84 kg/10 sqm) Ground floor Parapet wall Chajjas

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel work Grill

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat Grill

Providing and fixing aluminium sliding door bolts, 151 marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc complete :9.96.2 250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per 15: 1868) transparent or dyed required colour or shade, with necessary screws etc. complete 9.97.1 300x10m

Providing and fixing aluminium handles, ISI marked, anodised (anodic ting not less than grade AC 10 as per IS: 1868) transparent or dyed required colour or shade, with necessary screws etc. complete: 9.100.2 100 m

Steel work in built up tubular (round, square or rectangular mallow lubes etc.) trusses etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, Including welding and bolted with special shaped washers etc. complete. 10.16.1 Hot finished welded type tubes in all area = 400 sqm Truss 122 x 61 Bottom Purlin 96 x 48 MS Plate 10 mm

Providing corrugated G.S. Sheet roofing inclduing vetical/curved surface fixed with polymer coated J or L hooks, bolt and nuts 8 mm diameter with bitumen and G.I. Limpet washers or with G.I. Limpet washers filled with white lead, inclduing a coat of approved steel priemer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required 12.1.3 0.63 mm thihck with zinc coating not less than 275 gm/m2

Providing ridges or hips of width 60 cm overall width plain G.S.sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. Limpet and bitumen washers complete 12.4.2 0.63 mm thhick with zinc coating not less than 275 gm/m2

Dry brick pitching half brick thick in drains including supply of bricks with common burnt clay FPS (non modular) bricks of class designation Column Footing Plinth beam Floor

SANITARY INSTALATIONS & WATER SUPPLY WORKS Providing and fixing white viterous china pedestal type water closet (European type WC pan) with seat and lid, 10 litre low level white P.V.C. Flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1, W.C. Pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.1 brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets. cutting and making good the walls wherever require 17.7.4 White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to 15-7231, with all fittings and fixtures complete.17.18.1 10 litre capacity-White

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 17.28.2 Flexible pipe 17.28.2.1 32 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :17.32.2 Rectangular shape 453x357 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. 18.8.1 15 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 18.8.3 25 mm nominal dia Pipes

Boring with 100 mm diameter casing pipe for hand pump/ tubewell. In all soils except ordinary hard rocks requiring blasting, including removing the casing pipe after the hand pump/tube well is lowered and tested: 22.01 Up to 6 metres depth

Beyond 6 m and up to 12 m depth

Beyond 12 m and up to 18 m depth

Providing and placing in position filters of 40 mm diameter G.1. pipe with brass strainer of approved quality.

Providing and placing in position hand pump of approved quality for 40 mm diameter G.1. pipe complete with all accessories

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 18.50.1 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to 15:8931. 18.52.1 15 mm nominal bore

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.2 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

Providing and fixing PTMT Soap Dish/Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms.

Shower rose C.P. brass for 15 to 20 mm inlet 100 mm dia

Internal Electrical Works: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group A

Group B

Group C

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 4 sq. mm + 2 X 4 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

3 pin 5/6 amp socket outlet

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing PVC batten/ angle holder including connections etc. as required.

Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required. 125 Amp TP&N

Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 125 Amp, 16 KA, TPMCCB

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

6 way (4 + 18), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Triple pole and neutral

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying, installing, testing and commissioning of following capacity TPN distribution tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with HRC fuses, interconnections, earthing etc. as required. 63 amps TPN, 8 way

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying fitting & fixing of Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver. 20 W Havells ( Rate as per Price listenclosed )

Supplying fitting & fixing of 20 W LED bulb CROMPTON DYNARAY in the existing lamp holder as specified and directed by the department .