REPAIRS TO TOILETS BATHROOM DADAO INTERNAL PLASTERING SANITARY FITTINGS PLUMBING WORKS OF CERTAIN MARRIED ACCOMMODATION IN RESIDENTIAL AREA AT CVRDE AVADI

Amount

Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) all as specified and directed by Enginer-in-Charge.

Dismantling floor/wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises all as specified and directed by Enginer-in-Charge.

Taking down cement plaster on brick walls including racking out joints, hacking for key scrubbing down with water etc. all as specified and directed by Enginer-in-Charge.

Rendering 10mm thick in fair faces of brick work or concrete surfaces in CM 1:6 finished even an dsmooth with out using extra cement all as specified and directed by Enginer-in-Charge.

M&L for rendering 10mm thick in CM (1:3) on fair faces of brick work or concrete surfaces finished even and fair without using extra cement complete as in ceiling all as specified and directed by Enginer-in-Charge.

M&L preparing new wall surfaces and applying two coat of oil bound distempr over a coat of primer and wll putty all as specified and directed by Engr -in- Charge.

M&L preparing old decorated wall surfaces and applying one coat of oil bound distemper all as specified and directed aby Engr - in- Charge .

Preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed by Enginer-in-Charge.

M&L Preparation of old plastered, decorated surfaces and apply one coat of white wash on ceiling all as specified and directed by Enginer-in-Charge.

M&L for 25mm thick Cement concrete type B-0, 1:2:4 (using 12.5mm graded aggregate) surface finished even and rough to receive top finish all as specified and directed by Enginer-in-Charge.

M&L for15mm thick Screed bed or bedding layer in CM 1:6 for laying floor finishes all as specified and directed by Enginer-in-Charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Enginer-in-Charge.

M&L for Glazed ceramic coloured tiles in vertical surface 450x300x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick plaster in CM 1:3 complete all as specified and directed by Enginer-in-Charge.

S&f in repair shelf of PTMT fixed with and including plated brass screws and wooden/plastic cleats (minium weight 300gms) all as specified and directed by Enginer-in-Charge.

S&F Tubular towel rail 20mm dia D type 60cm long between flanges brass chromium plated all as specified and directed by Enginer-in-Charge.

Supply and fix in repair 15 mm bib taps, cast copper ally with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed but fancy type, chromium plated all as specified and as directed by the Engineer-in-Charge.

Supply and fix in repair 15mm stop valves/angle cock but fancy type, chromium plated, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions all as specified and as directed by the Engineer-in-Charge.

S&F in repairs Chromium plated brass shower rose 125mm size and 15mm dia with swivel joints all as specified and directed by Enginer-in-Charge.

Supply and fix in repair PVC connections 15mm size with PTMT nuts of length 300mm all as specified and as directed by the Engineer-in-Charge.

Supply and fix in repair grating doom 100 mm dia of PTMT (Minimum weight 25 gms)all as specified and as directed by the Engineer-in-Charge.

S&F Chromium plated cast copper alloy health facuet for 15mm dia including telephonic pipe SS Hose & holder Complete all as specified and directed by Enginer-in-Charge.

Supply and fix in repairs PVC valveless, syphonic action type, flushing cistern(Push type), low level, white, with inlet, ball valve, float and handle including brackets (10 Ltrs)all as specified and as directed by the Engineer-in-Charge.

Supply and fix in repair vitreous China wash basin, angle back, size 550x400mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets, cutting for and finning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe all as specified and as directed by the Engineer-in-Charge.

Supply and fix 32 mm waste fitting, brass, chromium plated for glazed ware WHB with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed all as specified and as directed by the Engineer-in-Charge.

Supply and fix 32 mm waste fitting, brass, chromium plated for glazed ware sink with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed all as specified and as directed by the Engineer-in-Charge.

Supply and fix 15 mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed but fancy type all as specified and as directed by the Engineer-in-Charge.

S&F in repair vitreous China squatting pan of pattern long pan size 580 mm white with 'P' or 'S' trap front or back inlet and footrest any pattern and fixed all as specified and directed by Enginer-in-Charge.

Supply and fix in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) including connection to trap and drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc complete all as specified and directed by Enginer-in-Charge.

Supply and fix in repair plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinges devices all as specified and as directed by the Engineer-in-Charge.

S&F in repair Fancy type cast copper with captain head, chromium plated, screwed down high pressure Mixer valve including three joints with L bend to steel pipes complete, screwed for 15mm dia iron pipe all as specified and directed by Enginer-in-Charge.

S&F low density 32mm polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to wall all as specified and directed by Enginer-in-Charge.

Taking down shutter of any description exc 1 sqm but n.exc 2 sqm each all as specified and directed by Enginer-in-Charge.

S&F factory made solid panel PVC door shutter (Approx size 0.70 x 2.05m) 30mm thick (Style) consisting of frame of size50 mmx47 mm made out of MS tubes for top & bottom rails, MS frames shall be covered with heat moulded plain colour PVC `C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert or top & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement incl solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube and comprising with aluminium mongeries such as 02 Nos 150mm size Aluminium tower bolt, 2 Nos 100 mm size aluminium handle, 03 Nos mild steel Aluminium 100 mm,3 Nos Hold fast incl including necessary fixing arranement with fixing wall and making good complete all as specified and directed by Enginer-in-Charge.

S&F sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wasters including bedding in cement in dwarf wall or including fixing cantiliver brackets and connecting union to pipe over all sixe 915 mm x 460mm , bowl sixe 410mm x 330mm x 160mm all as specified and directed by Enginer-in-Charge.

Supply and fix 40 mm waste fitting, brass, chromium plated for glazed ware sink with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed all as specified and as directed by the Engineer-in-Charge.

Supply and fix in repair 15 mm dia Drizzle soft brass valve tap, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed but fancy type all as specified and as directed by the Engineer-in-Charge.

Dismantling mild steel work for any description not otherwise provided all as specified and directed by Enginer-in-Charge.

S&F in repair steel windows with side hung shutters incl projecting type hinges with steel handles peg stays complete with glazing bars devotailed or welded after taking down existing damaged shutters complete all as specified and directed by Enginer-in-Charge.

Mild steel framed work such as grills gratings etc with ends of bars shouldered etc complete conforming to Fe-410-0 or Fe-310-0 complete all as specified and directed by Enginer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clipsall as specified and directed by Enginer-in-Charge.

Sheet glass, ordinary quality and glazing with oil putty in squares n.exc 0.50sqm in each pane 3.0mm thick complete all as specified and directed by Enginer-in-Charge.

Sheet glass, ordinary quality frosted on one side and glazing with oil putty in squares n.exc 0.50sqm in each pane 3.0mm thick complete all as specified and directed by Enginer-in-Charge.

Cutting windows/ventilators from its position and Welding with box type hinges including replacement of damaged member and making good the surface by painting with synthetic enamel paint including primer all as directed by Engr-in-charge

Securing glass of any description in existing metal frames glased with putty including removing loose or decayed putty painting/oiling one coat on rebales, reputtying and painting/oiling puttied furface to matel existing work all as specified and directed by Enginer-in-Charge.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed by Enginer-in-Charge.

S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or wire staples all as specified and directed by Enginer-in-Charge.

M&L for preparing of steel surface over 10cm width or girth and applying 2 coats of synthetic enamel paints over a coat of red oxide primer all as specified and directed by Enginer-in-Charge.

S&F Alumnium powder coated frame made out of hallow extruded aluminium section (minimum thickness of powder coating 50 micron) for windows/ventilators with one or more rebates including joining cleats, beads for fixing etc complete all as specified and as directed & approved by Engineer-in-Charge.

S&F Figured glass, pin headed type 4mm thick fixed with glazing clip, rubber beading /gasket in squares n. exc 0.5sqm in each pane all as specified and directed by Enginer-in-Charge.

S&F Alumnium powder coated louvers (movable arrangement in pair) for ventilators including locking arrangement complete all as specified and directed by Enginer-in-Charge.

S&F Figured glass, pin headed type 4mm thick fixed to aluminium lovers in strips width not exceeding 80mm all as specified and directed by Enginer-in-Charge.

S&F 300mm long aluminium anoised sliding door bolt with hasp staple (Bolt type) and fixing clips of sheet cast or extruded section and fixing both and sliding boths of external section or cast alumnium aloy and fixed all as specified and directed by Enginer-in-Charge.

S&F 200mm Aluminium anodized barrel tower bolts of extruded section and fixed all as specified and directed by Enginer-in-Charge.

S&F Butt hinges,100 mm, medium weight, cold rolled mild steel, and fixed all as specified and directed by Enginer-in-Charge.

S&F aluminium alloy anodised hinges 100 mm all as specified and directed by Enginer-in-Charge.

S&F 25 x 3 mm flat iron for hold fast confirming to Fe-290 Gde E-165 all as specified and directed by Enginer-in-Charge.

Cutting holes for fixing hold fast into or through brick wall built in cement mortar, superficial area n.exc 150 sq.cm, and making good in cement concrete 1:2:4, TypeB-1 as required all as specified and directed by Enginer-in-Charge.

Taking down steel water tubing and connection including cleaning for refixing for 15mm bore pipe and removing from site or work completeall as specified and directed by Enginer-in-Charge.

Taking down steel water tubing and connection including cleaning for refixing for 20mm bore pipe and removing from site or work complete all as specified and directed by Enginer-in-Charge.

S&F GI tubes 15 mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and directed by Enginer-in-Charge.

S&F GI tubes 20mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and directed by Enginer-in-Charge.

Re-fixing old serviceable GI tubing 15mm bore and connection complete all as specified and directed by Enginer-in-Charge.

Re-fixing old serviceable GI tubing 20mm bore and connection complete all as specified and directed by Enginer-in-Charge.

D Subramani and Sons

K Kumar Construction

M/s.Sai Agency