Conversion of First Floor of Old Animal House into Deemed SKIMS University office by way of renovation, modification/alteration at SKIMS.

Amount

Dismantling of old plaster or skirting including disposal of unserviceable materials within a lead of 50 Mtrs.

Demolishing of cement concrete including disposal of unserviceable materials within a lead of 50 Mtrs. ( 1:3:6 or richer mix)

Demolishing of brick work in cement mortar including disposal of unserviceable materials within a lead of 50 Mtrs.

Dismantling of doors , windows , C.Ws ( steel or wood ) shutter including chowkats, staking within a lead of 50 mtrs. ( area up to 3.0 Sqms )

Dismantling of Kota stone flooring laid in cement mortar including disposal of unserviceable materials within a lead of 50 Mtrs.

Demolishing of R. cement concrete including disposal of unserviceable materials within a lead of 50 Mtrs.

Extra for cutting of Reinforcement of bars in RCC or RB work .

Brick work with common burnt clay FPS brick bricks of class designation 75 in superstructure in

Half brick masonry using common burnt clay bricks in 1:4 mix. ( 41/2 “) including placing 2 no – 6mm dia bars at every 3rd layer.

Providing wood work in frames of Doors, Windows, etc and other frames (1st Class Deodar wood)

P/F of ISI marked 35 mm thick flush door shutter conforming to IS: 2202 (part-1) core of block board construction .

Extra over item No 11 for providing lipping with 1st class deodar wood 40mmx 25 mm

P/F of paneled or paneled and glazed shutters for doors, windows and (35 mm thick) 1st class Deodar wooden including glass panes (4 mm thick) .

Providing 40x5 mm flat iron hold fasts 40 Cm long

P/F of 35 mm thick wire guage shutters using galvanized MS wire guaze of average width for aperture 1:4 mix in both directions with wire dia of 0. 63 mm for Doors,Window and Clerestory window with hinges and necessary screws (1st class kail wood).

P/L RCC 1:1.5:3 with 20 mm nominal size stone aggregate

Reinforcement for R.C.C work including straightening, bending, binding and placing in position (TMT) Bars.

Shuttering and for RCC work including strutting propping and removal of the same

(a).Suspended floor

(b).Beams

( c).Columns

Structural Steel welded work in built up section truses and frame work including cutting, hoisting, fixing in position and applying a coat of steel primer.

P/F CGI sheet roofing 0.63 mm thick complete .

15 mm thick cement plaster in 1:4 mix

P/A White Cement based putty average thickness 2 mm of approved brand and manufacture over plastered surfaces Cement plaster.

Applying a priming coat of cement primer on plastered/ concrete surface.

Applying a priming coat with ready mixed grey primer of approved brand and manufacture on wood work.

Applying a priming coat with red-lead oxide on steel surfaces .

Painting on wooden surfaces with synthetic enamel paint of approved and shade (two or more coats on new wood surfaces)

Wall painting with emulsion paint of approved brand and manufacture to give an even shade (two or more coats).

P/L cement concrete 1:3:6 with 20 mm nominal size stone aggregate .

P/L of vitrified floor tiles in different size conforming to IS: 15622 of approved make including grating the joints with white cement and matching with cement pigment etc. complete 60 x 60 cm (10 mm thick) NITCO, SOMANY.

Kota stone floor 25 mm thick in 1:4 mix , joints finished with grey cement mixed with pigment of matching colour.

P/F of gang saw cut mirror polished (pre-moulded) and pre polished ) machine saw cut for kitchen plate form, vanity counters, window sills, facias and similar locations of required size of approved shade, colour, and texture laid over 20 mm thick base cement mortar 1:4 with joints treated with white cement mixed with matching pigment epoxy touch ups including rubbing curing, moulding and polishing etc. . Granite of any colour over or shape 18 mm thick.

P/F of 1st quality ceramic glazed tiles conforming to IS: 13753 of minimum thickness 7mm of approved make NITCO, SOMANY, KAJARIA or equivalent over 12 mm thick bed of cement mortar 1:3 including pointing with White cement etc. complete.

P/F 300x300mm ceremac floor tiles in 1:3 mix confirming to IS – 13753

Extra for edge moulding to 18 mm thick marble stone counters vanities etc. (Granite).

P/F of Stainless Steel (Grade 304) railing made of Hollow tubes, channels, plates, including welding, grinding, buffing, polishing, and making curvature wherever required including all fittings etc. complete.

P/F of Aluminum sheet on door shutters (3 mm thick )

P/F of hardware fittings.

Mortice latch and lock die cast with a pair of CP handles with Metal screws.

Hydraulic door closer complete with all accessories

CP Brass door stooper with white Rubber Cushion

Brass Chrome plated D-type flat handles.

Brass C.P barrel type tower bolts

Rod Lock of approved quality

C.P brass handles 100/ 125 mm

P/F of aluminum work for Doors, windows etc. and partitions with extruded built up section, standard tubular sections of approved Z section conforming to IS: 733 and IS: 1285 fixed with dash fastener including necessary filling of gaps at junctions with required EPDM rubber / Neoprene gasket felt etc. Powder coated aluminum (Min thickness of powder coated 50 microns).

P/F of glazing in Aluminum door, window, Ventilators shutter and partition complete with float glass EPDM rubber / neoprene gasket etc. complete.

(a).10.0 Kg/m2 (4mm)

(b).13.5 Kg/m2 (5.5 mm)

P/F of Aluminum composite panel (ACP) sheet (3.00 mm thick ) of approved make

P/F of double action hydraulic floor spring of approved brand and manufacture IS: 6315 with stainless steel cover plate 1.25 mm thick

P/F of pre – polished paneling of imported wood including cost of Budloo wood james and 12 mm thick ply particle board

P/F of Khatam Band ceiling Majma type including base work of 12 mm thick ply particle board duly polished .

P/F of wardrobes of 18 mm thick board of approved quality ( 1’- 9” ) average depth, outer faces finished with 0.8mm thick mica , inside painted with synthetic enamel paint including brass fittings fixtures with ornamental nature as per approved pattern.

Pebble dash plaster with a mixture of washed pebbles or crushed stone 6 mm to 12.5 mm nominal size dashed into coats .

Removing / dismantling of pebble dash plaster including scaffolding complete.

varnishing of pebble dash plaster after washing of stones and groves with detergent including scaffolding complete.

P/F of G.I gutter 100 mm dia complete including cost of m.s clamps ( PGI 26 gauge )

Rectification of CGI roofing sheets by way of applying m- seal etc complete job

Making plinth protection 50 mm thick of cement concrete 1:3;6 mix over 75 mm bed of dry brick ballast 40 mm nominal size well rammed, consolidated and grouted with fine sand including finishing the top surface.

Brick edging 7 cm wide 11.4 cm deep to plinth protection with bricks of class designation including grouting with cement mortar.

P/F Water closet squatting pan (Indian type W.C) with 100 mm sand C.I, P or S trap, 10 litre low level PVC flushing cistern including flush pipe of approved make manually controlled device conforming to IS 7231 with all fittings and fixtures including cutting, and making good the walls and floors where required. Orrisa pattern white vitreous china W.C Pan of size 580 x 440 mm with integral foot rests.

P/F of Vitreous China pedestal type WC (European type WC) with seat and lid, 10 litre low level white PVC flushing cistern including flush pipe conforming to IS : 7231 with fittings and fixtures.

P/F of CP Bib Cock (JAQUAR/PARKO- VEC)

P/F of CP Angle Valve of approved make (JAQUAR/PARKO-VEC.

P/F of Wash Basin with C.I/ MS brackets, 15 mm CP brass pillar taps, 32 mm CP brass waste of standard pattern (White vitreous China) size 550 x 400 mm (CERA/HINDWARE)

P/F of stainless steel ISI 324 kitchen sink as per IS: 13983 with CI brackets and stainless steel plug 40 mm.

P/F of CI Pipe ISI mark jointed with Cement mortar/ Lead caulked joints including cost of Earth work in trenches for pipes and filling of the same with cost of all assorted fittings such as junctions, bends, reducers, collars including cost of lead etc complete.

(a).150 mm dia pipe

(b).100 mm dia pipe.

( c)..75 mm dia pipe

(d).50 mm dia pipe

P/F of GI pipe class B including GI fittings (on walls)

(a).20 mm dia

(b).32 mm dia

(c ).15 mm dia

P/F of CI floor trap including cost of lead jointing.

a. 100 mm dia.

b. 75 mm dia

P/F of Gun Metal Gate valve with CI Wheel approved quality.

(a).32 mm bore.

(b).20 mm bore.

P/F of CP Soap Case of standard size.

P/F of looking mirror of superior glass 450 x 600 mm in size.

P/F of 600 x 120 x 5 mm glass shelf

P/F of Toilet paper holder. (CP Brass)

P/F of 100 mm CP Grating

P/F of 75 mm CP Grating

P/F of CP Towel rod complete.

P/F of CP Connection 18” long.

P/F of CP Nipples complete.

P/F of CP mixer for wash basin and sink of approved quality.

P/F of PVC waste pipes 40 mm (2 ft length).

P/F of CP Brass Ball Valve 20 mm

P/F of three layered PVC water storage tank with fittings complete.

Cutting chases in complete brick massonary walls for CI pipes and making good the same.

100 mm dia

150 mm dia

Construction of brick masonry chamber with internal size of 450 x 450 x 600 mm R.C.C 1:2:4 slab as top in 1:2:4 and inside plastered with cement mortar 1:3 12 mm thick finished with a floating coat of neat cement complete as per standard design

P/L of non pressure NP3 class RCC pipes with collars jointed with stiff mixture of cement mortar in proportion of 1:2 including testing of joints complete 300 dia RCC pipes .

P/F white vitreous China flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm and 340 x 410 x 265 mm size respectively with automatic fleshing cistern with C.I / M.S brackets complete. One urinal basin with 5 litere PVC white automatic fleshing cistern of approved quality.

M/S ALLIANCE CONSTRUCTIONS

M/S MOHAMMAD ASHRAF GILKAR ENGINEERS AND CONTRACTORS

M/S M.I.CONSTRUCTION

M/S BHAT CONSTRUCTIONS

M/S FALCON CONSTRUCTION COMPANY