SPECIAL REPAIRS TO JCO MESS BLDG NoP15 OF CERTAIN UNIT AT LICHUBARI SPECIAL REPAIRS TO BLDG No.P39 SINGLE JCOACCN OF CERTAIN UNIT AT LICHUBARI AND SPECIAL REPAIRS TO BLDG NoP169 P171 FAF ACCN AT LICHUBARIIN JORHAT MILITARY STATION UNDER GE JORHA

Amount

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as directed.

Demolition of cement concrete (un reinforced) in any position not otherwise specifically provided for, complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n. exc. 1.5 Sq. M each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sq. M but not exc. 4.0 Sq M each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n. exc. 1.5 Sq. M each and refixing in other opening, complete all as directed.

Resecuring or easing & adjusting without taking down, shutters of any description exc. 1.00 Sq. M and n. exc. 2.00 Sq. M each, complete all as directed.

Dismantling timber scantling in unframed work, 40 Sq cm and over in section, in any position, complete all as directed.

Dismantling of timber boarding, any description, fixed in any position with screws complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as directed.

Dismantling of Asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as directed.

Taking up or down, steel tubing 15 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Taking up or down, steel tubing 20 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Taking up or down SWR pipes(any size or pattern ) including all fittings 'T' bends etc including removal to store for taking credit (measured overall as fixed along the centre line over fittings and accessories) complete as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil, complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil ,complete all as specified and directed.

Returning filling in soft/loose soil, including, spreading levelling watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 Metres and depositing where directed at a level n. exc. 1.5 M above the starting point complete all asspecified and directed.

Materials and Labour for sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

Materials and Labour for, broken stone or boulder hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface , complete all as specified and directed.

Materials and Labour for plain cement concrete (1:4:8) Type D-2 using 40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed.

Materials and Labour for plain cement concrete (1:3:6), Type C1,using 20mm graded aggregate in filling of pressed steel chowkhat complete all as specified and directed.

Materials and Labour for plain cement concrete (1:2:4) type B1 using 20 mm graded aggregate in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary from work complete all as specified and directed.

Materials and Labour for pre cast reinforced cement concrete (1:2:4) Type B1 (using 20 mm graded aggregates) in landings, covers slabs (for man holes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in cement mortar (1:4), complete all as specified and directed. Note: - Reinforcement will be measured and paid separately.

Materials and Labour for reinforced cement concrete 1: 1½ :3, Type A1(using 20 mm graded aggregated) in beams, cantilever, bressumers, lintels over 1.5M Span,complete all as specified and directed.

Materials and Labour Extra for forming fair finishing to surfaces channels/drain 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, etc complete all as specified and directed.

Supply only integral water proofing compound all as specified

Materials and Labour for brick work with Sub Class ‘B’ bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:6), complete all as specified and directed.

Materials and Labour for,cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, in stone concrete block or slab walls, complete all as specified and directed.

Materials and Labour for Cutting holes in brick walls, not exc. half brick, built in cement mortar, for inserting holdfasts and making good dismantled portion in cement mortar (1:3) or cement concrete 1:2:4 Type B-1 as required (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall) complete all as specified and directed.

Cutting openings, through brick walls built in cement mortar or cement lime mortar, for door, window and other openings or enlarging existing openings,converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc. to store and rubbish not exc. 50m, complete all as directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings , girders, bressummers, lintels, cantilevers, shelves including supports,overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete, flat, complete all as specified and directed.

Supply and Fix, second-class hard wood timber scantlings, clean sawn, in unframed works and in any position, fixed with nails complete all as specified and directed.

Supply and fix second class hard wood plain fillets, square, rectangular or triangular in section,wrought, of cross sectional area exc. 6.00 Sq cm and n. exc. 13.00 Sq cm, fixed with screws, complete all as specified and directed.

Supply and fix second class hard wood plain fillets, square, rectangular or triangular in section, clean sawn, of cross sectional area exc. 13.00 Sq cm and n. exc. 25.00 Sq cm, fixed with nails, complete all as specified and directed.

Supply and Fix, second class hard wood, plain, solid, straight chowkhats and frames, wrought, framed, rebated on the solid, rounded or chamfered put together with glue, pinned at joints, complete all as specified and directed.

Supply and Fix, 30 mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

Supply and Fix, factory made rigid lam PVC door frame of size 125 mm x 50 mm, double rebated with wall thickness of extruded 5mm PVC sheet of density 600 kgs/cum , made by joining 3 Nos. heat bent PVC sheet 'C' channel of 5mm PVC foam sheet of size 35mm x 35mm x 25mm & 40mm x 55mm x 40 mm & 25 mm x 35 mm x 35 mm using solvent cement, the two side 'C' channel shall be reinforced with 19mm x 19 mm MS square tube of 19 SWG with all three 'C' ed to flat base of 5mm PVC sheet with solvent cement. The profile shall be mitred cut at two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x15 mm MS square tube inside the 19 mm square tubes. The two vertical members of door frame shall be reinforced with 40mm x 20 mm MS tubes of 19 SWG duly filled with 2nd class hardwood throughout the frame. The door frame shall be fixed to the wall using 100 mm long nikel coated dry wheet screws through the frame by using PVC fastener. Minimum 08 Nos. of screws shall be provided for each vertical member and minimum 04 Nos.for horizontal members etc. as per manufacturers specifications, fixed in opening, complete all as specified and directed.

Supply and Fix, factory made rigid lam PVC door frame of size 100 mm x 50 mm, double rebated with wall thickness of extruded 5mm PVC sheet of density 600 kgs/cum , made by joining 3 Nos. heat bent PVC sheet sections. The inside section of size 90mm x 30 mm shall be made from colour PVC sheet of 5 mm thickness.The inside section shall be covered by sticking two sections of size 35mm and 6 x 45 mm made from 5mm thick plain sheet. The frame shall be mitred cut at two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x15 mm MS square tube. The two vertical members of door frame shall be reinforced with 40mm x 20 mm MS tubes of 19 SWG duly filled with 2nd class hardwood throughout the frame. The door frame shall be fixed to the wall using 100 mm long nikel coated dry wheet screws through the frame by using PVC fastener. Minimum 04 Nos. of screws shall be provided for each vertical member and minimum 02 Nos.for horizontal members etc. as per manufacturers specifications, fixed in opening, complete all as specified and directed.

Supply and Fix, solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, fixed in opening all as specified and directed.

Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm single side prelam PVC sheet with edges painted to match with prelam sheet, reinforced with MS square tube, fixed in opening, complete all as specified and directed.

Supply and Fix, factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail: Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed to door frame complete all as specified and directed.

Supply and Fix, factory made wire gauzed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

Supply and Fix, factory Made Solid PVC Moulded Door Shutter with particle board core, 35mm thick (stiles), with 2, 4, or 6 raised panel design with 5mm thick Moulded PVC Sheet on the front face & 5mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

Materials and Labour for, Factory Made Solid PVC Moulded Door Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing, complete all as specified and directed.

Supply and fix second class hard wood small fittings such as brackets of any type, latch and hinge blocks shaped door and windows stops and the like, including all necessary labours; articles n. exc. 200 Cu cm each complete all as specified and as directed.

Supply and Fix, SS butt hinges, medium weight, cold rolled 75 mm size complete all as specified and directed

Supply and Fix, mild steel butt hinges, medium weight, cold rolled 100 mm size complete all as specified and directed

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 100 mm long complete all as specified and directed.

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 200 mm long complete all as specified and directed.

Supply and Fix, extruded aluminium alloy handles, fabricated type, anodized, 125 mm size, complete all as specified and directed.

Supply and Fix, extruded aluminium alloy handles, fabricated type, anodized, 150 mm size, complete all as specified and directed.

Supply and Fix, aluminium handles, cast type, anodized, 150 mm size, complete all as specified and directed.

Supply and Fix, mild steel, 300 mm, ordinary rat-tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and Fix, Aluminium Alloy, anodised, sliding door bolt, length of bolt 300 mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and Fix, aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples, complete all as specified and directed.

Supply and Fix, stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and Fix, chicken wire mesh of size 12.5 mm x 0.51 mm (24 SWG) hexagonal construction including all laps, cutting and waste,complete all as specified and directed.

Supply and fix mild steel TMT bars 10 mm dia. and over, cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Supply and fix mild steel TMT bars 8 mm dia. and over, cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Supply and fix mild steel TMT bars 5 mm dia. and over up to and including 10 mm dia. in stirrups, spacers, binders etc. cut to length, bend to shape required including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed.

Supply and Fix, mild steel screw bolts (machine made), with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, diameter of shank 5 to 10 mm, length of bolt n. exc. 5 long, complete all as specified and directed.

Materials and Labour for mild steel works, conforming to Fe 290, Grade E-165 , in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles, complete all as specified and directed.

Materials and Labour for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Grade E-165 complete all as specified and directed.

Materials and Labour for rolled mild steel,Fe 410-W (Grade E-250) Quality-A in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., complete all as specified and directed.

Erection and Fixing Only, rolled mild steel, in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., complete all as directed. Note:- Old steel obtained from Serial Item No.10 here in before shall be refixed.

Materials and Labour for rolled mild steel , conforming to Fe 410-W (Grade E-250) quality-A, as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guide for sliding doors; fixed with angle cleats or other connecting plates, complete all as specified and directed.

Materials and Labour for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS1161-1979 grade St.-240, complete all as specified and directed.

Supply and Fix, pressed steel frames, size 125 x 60mm, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified and directed.

Supply and fix alluminium sliding window with powder coated (minimum thickness of powder coating 50 micron) including following components/specifications complete all as specified and directed (i) two leaf of glazed sliding shutters and one leaf of guaged (fly proffing) sliding shutter with alunminium grill of design DG 104 pattern made out of 7.5mm plate and finished grill have 7.5mm width and 6 mm thick complete all as per manufcaturer intruction(Make:decogrill or equivalent make ) . ( iii)All vertical/Horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members.(iv)All other accessories such as jointing cleats,glazing clips,rubber neoprene packing anodised aluminium snap beading ,screws etc (iii)Thickness and weight per metre lenght of aluminium frame and section and other rest details all as specified in drawing no.CESZ/2015/TD/007 sheet no.1R/5,2R/5,3R/5,4R/5 & 5R/5 Note: 1.Sheet glass, aluminium grill and stainless steel wire mesh and all other items as shown on drawing shall be included in quoated rate .2.Mode of measuremt : Only opening size of window shall be measured

Supply and Fix, tuffen glass (plain or tinted) door shutter, 12 mm thick (single/double leaf) complete with all accessories as per manufacturers instructions including suitable locking arrangement and handle 200 mm long of approved design, complete all as specified and directed.

Supply and Fix, tuffen glass (plain or tinted) window shutter, 12 mm thick (single/double leaf) complete with all accessories as per manufacturers instructions including suitable locking arrangement and handle 200 mm long of approved design, complete all as specified and directed.

Supply and Fix,anodized aluminium frame, 100 mm x 45.5 mm x 1.5 mm thick for with one or more rebates including joining cleat for fixing etc., with anodized aluminium glazed shutters (single/double) fixed/openeable/partition, divided into two parts,with top,bottom & mid/lock rail sections 100 mm x 44 mm x 1.5 mm and styles sections 100 mm x 45.5 mm x 1.5 mm including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc.,with and including 5 mm thick tinted glass, complete all as specified and directed.

Supply and Fix, brass 2 Levers lock suitable for locking arrangement in aluminium shutters, complete all as specified and directed.

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based corrugated steel sheet, 0.60mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.Make:Tata blue scope or equivalent amke as approved by GE

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based plain steel sheet, 0.60 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed..Make:Tata blue scope or equivalent make as approved by GE

Materials and Labour for exposed metal frame ceiling with 6mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid with and including exposed metal frame using hot dip galvanised steel, exposed pre-coated ceiling suspension system of grid size 600 mm X 600 mm, with main runner ‘T’ section 24 mm (W) X 38 mm (H) X 0.40 mm (T), cross ‘T’ section 24 mm (W) X 28 mm (H) X 0.30 mm (T) , wall angle 24 mm X 24 mm X 0.43 mm (T) and suspended with 4 mm dia. GI hangers/wire fixed with steel dash fasteners from purlins/soffits spaced at 1200 mm centre to centre with butterfly clips, hold down clips, providing provisions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc., complete all as specified and directed.

Materials and Labour for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 mm and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre ; intermediate channel 0.90 mm thick having two equal flanges of 15 mm each and web of 45 mm, suspended from soffit at approx 900 mm centre to centre with GI cleat , GI hanger 6mm dia. and steel expansion fasteners with and including ceiling sections (not exceeding 1.2 M length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to intermediate channel with connecting clips across the intermediate channel at 475 mm centre to centre including Gypsum Board 12.5 mm thick in ceiling fixed with screw as per manufacturers instructions,complete all as specified and directed.

Materials and Labour for 6 mm thick, asbestos cement plain building boards, fixed to timber framework with screws in ceiling flat or sloping, complete all as specified and directed.

Materials and Labour for waterproofing treatment to existing RCC roof in the following steps complete all as specified and directed. (i) Complete removal of the existing water proofing treatment. (ii) Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq. m, blinded with grit or pea size gravel @ 0.006 cu.m per sq.m, and lightly tampered (area of flashings, etc., shall be added to the roof area) (iiii) Supply and Laying, chicken wire mesh of size 12.5 mm x 0.51 mm (24 SWG) hexagonal construction including all laps, cutting and waste in fabric reinforcement to PCC roof padding including providing 40 mm thick plain cement concrete (1:2:4) type B0using 12.5 mm graded aggregates as in roof padding. (iv) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:3), mixed with liquid water proofing compound as per manufactures instructions, on concrete surface of roofs or terracing and finishing surface even and smooth without using extra cement. (iv) Waterproofing treatment over smooth finished surfaces after application of cold applied bituminous primer @ 0.30 Kg /Sq M,, providing and laying APP polymer, modified, non-woven polyester fabric of 150 grams/square metre, reinforced membrane, 3.00 mm thick, weighing 3.00 Kg / Sq M, with surface finish of white mineral, by torch on application method, with minimum 75 mm overlap on longitudinal direction and 100 mm overlap on the transverse direction and finally applying with one coat of bituminous based solar reflective aluminium paint @ 100 gms / Sq M complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded aggregate as in sub base in floor/paving/hardstanding , complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates as in sub base of floor/pavings/hardstanding, complete all as specified and directed.

Materials and Labour for 100 mm thick plain cement concrete (1:2:4) type B2 using 40 mm graded aggregates as in paving/hardstanding including finishing surface even and smooth without using extra cement and including spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green , complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates as in plinth protection including finishing surface even and smooth without using extra cement complete all as specified and directed.

Materials and Labour for,Digital/printed glazed ceramic coloured tiles, 600 X 400 X 9-10mm thick,conforming to ISO 13006, EN 14411 Grade B III, on vertical surface of wall such as dados,skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match,over and including 10 mm thick rendering cement mortar (1:3) complete all as specified and directed.

Materials and Labour for,digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,conforming to IS 15622 ,ISO 13006, EN 14411 , Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match,over and including 15 thick screed bed cement mortar (1:6) complete all as specified and directed

Materials and Labour for, digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to IS 15622 ,ISO 13006, EN 14411 , Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15 thick screed bed cement mortar (1:6) complete all as specified and directed

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to conforming to IS 15622 ,ISO 13006, EN 14411 , Grade B II, on vertical surfaces of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match,over and including 15 thick screed bed cement mortar (1:6) complete all as specified and directed

Materials and Labour for Digital , Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm conforming to IS 15622 ,ISO 13006, EN 14411 , Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match,over and including 15 thick screed bed cement mortar (1:6) complete all as specified and directed

Material and Labour for digital Vitrified Ceramic Tiles,, 10 mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sq M, on floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour, over and including 20 thick screed bed cement mortar (1:6) complete all as specified and directed

Material and Labour for Digital Vitrified Ceramic Tiles, Light Shade, 10 mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sq M, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour,over including 10 mm thick rendering cement mortar 1:3 complete all as specified and directed

Materials and Labour for machine cut Kota stone slab flooring 20-25 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing,over and including 20 thick screed bed cement mortar (1:6) complete all as specified and directed

Materials and Labour for machine cut Kota stone slab 20-25 mm in raisers of steps, skirting, dado and pillar thick laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing,over including 15 mm thick rendering cement mortar 1:3 complete all as specified and directed.

Materials and Labour for Granite (of any type) tiles 18-20mmthick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, over and including 20 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.

Material and Labour for Machine Pressed Precast Concrete Interlocking Paver Block ,with grey cement and pigment, any shape and size conforming to IS 15658-2006, of 60 mm thickness, M-35 Grade,laid on pavements, complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded aggregate as in sub base in floor/paving/hardstanding , complete all as specified and directed.

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface other than fair face of brickwork and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed.Note: - (Water proofing compound will be measured and paid separately)

Material and Labour for rendering 5 mm thick cement plaster in cement mortar (1:3) on concrete surfaces in ceiling, complete all as specified and directed.

Material and Labour for applying three coats of white wash to new plastered surfaces on walls including preparation of surfaces complete all as specified and directed.

Material and Labour for applying two coats of white wash to new plastered surfaces in ceiling including preparation of surfaces, complete all as specified and directed.

Material and Labour for applying one coat of white wash to old decorated plastered or un plastered surfaces on walls including preparation of surfaces complete all as specified and directed.

Material and Labour for applying one coat of white wash to old decorated plastered or un plastered surfaces in ceiling including preparation of surfaces complete all as specified and directed.

Materials and Labour for applying applying two coats of oil bound distemper, white or tinted over 3mm thick wall care putty, to new plastered surfaces on walls including preparation of surfaces, complete all as specified and directed.

Material and Labour for complete removal of existing treatment and applying two coats of oil bound distemper,white or tinted over 3mm thick wall care putty, to old plastered or unplastered surfaces on walls including preparation of surfaces, complete all as specified and directed.

Material and Labour for applying two coats of exterior acrylic emulsion base premium quality matt finish weather coat anti fungal paint, to new plastered surfaces on walls over including acrylic emulsion based primer as per manufacturers intructions and including preparation of surfaces complete all as specified and directed.

Material and Labour for complete removal of existing treatment and applying two coats of exterior acrylic emulsion base premium quality matt finish weather coat anti fungal paint, to new plastered surfaces on walls over including exterior acrylic emulsion based primer as per manufacturers intructions and including preparation of surfaces complete all as specified and directed

Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Supply and Fix,3 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying one coats of synthetic enamel paint on old wood or wood based surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying one coats of synthetic enamel paint on old steel surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Preparing surfaces of wood and wood based materials,steel and iron work, new or old,of any description and girth,not otherwise described, and treated with tar or coal tar black paint, complete all as specified and directed.

Preparing surfaces of wood and wood based materials,steel and iron work, new or old,of any description and girth,treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc.,area n exc 0.1 sq. m each with tar or coal tar black paint, complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 15 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 20 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Material and Labour for 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part – I complete, all as specified and directed.

Materials and Labour for, Ball valves high pressure of PTMT (Minimum weight 210 gms) with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe, 20 mm bore and fixed complete all as specified and directed.

Supply and Fix, bib tap, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, including taking out existing unserviceable complete all as specified and directed.Make(Jaquar/Kohler or equivalent make as approved by GE)

Supply and Fix, bib tap, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, including taking out existing unserviceable complete all as specified and directed.Make(Jaquar cat no.QQT 7037or equivalent make of Kohler or equivalent make as approved by GE)

Supply and Fix, stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 15 mm bore,including taking out existing unserviceable complete all as specified and directed.Make(Jaquar cat no.QQT 7053or equivalent make of Kohler or equivalent make as approved by GE)

Supply and Fix, stop valves, cast copper alloy , fancy type, chromium plated, screwed down, high pressure with long shank and cup (concealed type), screwed both ends for steel pipe of for unions, 15 mm bore,including taking out existing unserviceable complete all as specified and directed.Make(Jaquar cat no.QQT 7083or equivalent make of Kohler or equivalent make as approved by GE)

Supply and Fix, pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, 15 mm bore, ,including taking out existing unserviceable complete all as specified and directed.Make(Jaquar cat no.QQT 7011 or equivalent make of Kohler or equivalent make as approved by GE)

Supply and Fix, brass chromium plated shower rose 125mm size,with swivel joints, fixed to steel pipe or union 15 mm bore,,including taking out existing unserviceable complete all as specified and directed.Make(Jaquar / Kohler or equivalent make as approved by GE

Supply and Fix,sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes;including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm,complete all as specified and directed.

Supply and Fix, vitreous China wash basin, white, flat back, size 550 X 400 mm excluding taps, waste chain and porcelain stopper, but including brackets, complete all as specified and directed.

Supply and Fix vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440 mm, white, with integral foot rests and with ‘P’ or ‘S” trap, (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including provision of lime concrete bedding, complete all as specified and directed.

Supply and Fix PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, of capacity 10 Litres, including brackets, flush pipe, complete all as specified and directed.

Supply and Fix vitreous China wash down water closet pastel/coloured utilitarian style (including flushing cistern and flush pipe ) including connection to trap and to flushing pipe and other acessories, etc and including provision of lime concrete bedding, complete all as specified and directed. Make( Hindware cat part no.20048 or equivalent make of cera/parryware

Supply and Fix massage Bath tub made from high gloss lucite acrylic material modula premium model size 1680mmx800mmX500mm white/Ivory coloured including complete acessories like Bath tub ,front panel, side pannel stainless steeel body frame,Jacuzzi system with six hydrojets, Two spinal jets,ON/OFF switch,pressure regulator & Jazuzzi Pump 1 HP,Pneumatic contol panel Authomatic shutdown safty protection against high current leakage,Bath Tub filler set with Hand shower,Pop uo waste rotary knob,water level controller,Sleek headrest pillow suction unit,self draining pipes,Hot& cold mixer,water filler,Drain pipe, and other acessories including wiring for complete functioning as specfied and directed Make: Romania or equivalent model of Jaquar or equivalent model as approved by GE

Supply and Fix, waste coupling of PTMT (half or full threaded) (Minimum weight 45gms), for 32 mm bore discharge pipe,complete all as specified and directed.

Supply and fix PVC connections 15 mm size with PTMT nuts of length 450 mm,complete all as specified and directed.

Cutting into existing manholes for connecting new drains (Internal dia. of pipe 100mm) , making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required,complete all as specified and directed.

Supply, laying, jointing and testing of Salt Glazed stoneware drain pipes, Class ‘SP1’, 150 mm internal dia, laid in trenches and jointed complete all as specified and directed.

Materials and Labour for,concrete bed to 150 mm bore drain pipes including forming cradles;in cement concrete 1:4:8, Type D2 using 40 mm graded aggregate, complete all as specified and directed.

Materials and Labour for,concrete bed to 150 mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:3:6, Type C2 using 40 mm graded aggregate, complete all as specified and directed.

Supply and Fix, 50 mm bore unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe, complete all as specified and directed.

Supply and Fix, 110 mm bore PVC (SWR) bends any radius, with access door, complete all as specified and directed.

Supply and Fix, 75 mm bore PVC (SWR) bends any radius, with access door, complete all as specified and directed.

Supply and Fix, PVC (SWR) floor trap, plain with grating including jointing with solvent cement with dia. of out let 75 mm, complete all as specified and directed.

Supply and Fix,grating square fitting of size 150mm made in two parts for smell and mosquito proofing with minimum 25 mm water seal of PTMT. (Minimum weight 85gms), complete all as specified and directed.

Supply and Fix, cast iron traps ‘P’ or ‘S’ suitable for 100 mm bore pipe, complete all as specified and directed.

Supply and Fix,100mm cast iron sanitary connection socket to fit WC out-let, complete all as specified and directed.

Supply and Fix,100mm cast iron sanitary connections short connections pipe of length upto 300 mm, complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down copper/aluminium sub main wiring complete and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Materials and Labour for point wiring with 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC casing and capping complete with all fittings and accessories, fixed to walls/ceiling, including sunk type pressed steel terminal boxes 60 mm deep, conforming to IS-5133 (Part-I) with 3 mm thick plastic laminated sheet cover (ISI Marked) for mounting switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly for, one light point or one fan point controlled by one switch, complete all as specified and directed.

Materials and Labour for point wiring with 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC casing and capping complete with all fittings and accessories, fixed to walls/ceiling, including sunk type pressed steel terminal boxes 60 mm deep, conforming to IS-5133 (Part-I) with 3 mm thick plastic laminated sheet cover (ISI Marked) for mounting bell push etc and including 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly for, one bell point point controlled by one bell push, complete all as specified and directed.

Materials and Labour for point wiring with 2.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC casing and capping complete with all fittings and accessories, fixed to walls/ceiling, including sunk type pressed steel terminal boxes 60 mm deep, conforming to IS-5133 (Part-I) with 3 mm thick plastic laminated sheet cover (ISI Marked) for mounting switch/socket outlet etc and including 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly for one 3 pin socket outlet, 5 amps, independent,, complete all as specified and directed.

Materials and Labour for point wiring with 4.00 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC casing and capping complete with all fittings and accessories, fixed to walls/ceiling, including sunk type pressed steel terminal boxes 60 mm deep, conforming to IS-5133 (Part-I) with 3 mm thick plastic laminated sheet cover (ISI Marked) for mounting switch/socket outlet etc and including 2.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly for one 3 pin socket outlet, 15 amps, independent,, complete all as specified and directed.

Materials and Labour for two single core FRLSH PVC insulated unsheathed cable 6.00 Sq. mm. (Nominal area) with stranded copper conductor cable, 1100 Volts grade, drawn in PVC Casing and Capping and continuous earth wire of single core FRLHS PVC insulated, unsheathed cable 4.00 Sq. mm (nominal area) with stranded copper conductor cable, 1100 Volts grade for sub main wiring, complete all as specified and directed.

Materials and Labour for two single core FRLSH PVC insulated unsheathed cable 4.00 Sq. mm. (Nominal area) with stranded copper conductor cable, 1100 Volts grade, drawn in PVC Casing and Capping and continuous earth wire of single core FRLHS PVC insulated, unsheathed cable 2.50 Sq. mm (nominal area) with stranded copper conductor cable, 1100 Volts grade for sub main wiring, complete all as specified and directed.

Supply and Fix, switch piano, flush button, single pole, one way, 5 Amps, complete all as specified and directed.

Supply and Fix, bell push, flush type, 5 Amps, complete all as specified and directed.

Supply and Fix, switch piano, flush button, single pole, one way, 15 Amps, complete all as specified and directed.

Supply and Fix, ceiling rose, three terminal, PVC/ Polycarbonate insulated body, complete all as specified and directed.

Supply and Fix stepped type electronic fan regulator, flush type, on existing phenolic laminated sheet etc. as required , complete all as specified and directed.

Supply and Fix lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings,complete all as specified and directed.

Supply and Fix, bell ,ding dong, AC. 230 volts, single pole, complete all as specified and directed.

Supply and Fix, switch socket combination, 3 pin, 5 Amp,flush type , complete all as specified and directed.

Supply and Fix, switch socket combination 3 pin 16A, flush type, complete all as specified and directed.

Supply and Fix, socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type, complete all as specified and directed.

Supply and Fix, LED lamp, 7 Watts, lumen output 770 lm, colour temp 6500 K, lamp current 0.04 amp, lamp base cap B22, complete all as specified and directed.

Supply and Fix, LED tube light fitting, 20 Watts, lumen output 2000 lm, colour temp 6500 K, lamp base cap G13, all as per Cat No. LHLDDBXEML6X020 of Make ‘Havells’ or Equivalent Model of Make Bajaj/Philips and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, including taking out old unserviceable complete all as specified

Supply and Fix, LED roadway luminaire, 15 Watts, with pressure die-cast aluminium housing, high power LEDs as light source and electronic driver, colour temp 6000 K, all as per Cat No. LHETAXU7IN6W015 of Make ‘Havells’ or Equivalent Model of Make Bajaj/Philips and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.75 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet,and including provision of fixing bracket made out of 25 mm bore galvanized steel tubing, medium grade, (1.5 RM Approx), bent to shape required and fixed to wall/pole with FI clamp 25 X 3 mm, nuts, bolts and washers, including taking out old unserviceable complete all as specified

Supply and Fix, Sheet Metal Enclosure with Socket Plug Top and MCBs, Single Pole & Neutral enclosure with a two pin and earth plug and socket, complete with one single pole MCB, 240V, 20 Amps, including taking out old unserviceable complete all as specified

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 240 Volts, 8 way, with 200 Amps rated bus bar, Single Pole & Neutral, including taking out old unserviceable complete all as specified . [Cat No.DBSPN008DD of Make L&T or equivalent Model of Make Legrand/Siemens]

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 415 Volts, 4 way, with 200 Amps rated bus bar, Triple Pole & Neutral, including taking out old unserviceable complete all as specified . [Cat No.DBTPE004DD of Make L&T or equivalent Model of Make Legrand/Siemens]

Supply and Fix, miniature circuit breaker (MCBs), single pole, 240 Volts,10KA, 6-32 Amps complete all as specified and directed.

Supply and Fix, miniature circuit breaker (MCBs), single pole, 240 Volts,10KA, 40 Amps complete all as specified and directed.

Supply and Fix, miniature circuit breaker (MCBs) three pole and neutral, 415 Volts, 10KA, 63 Amps complete all as specified and directed.

Supply,laying, jointing and testing of , XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 16 sq. mm 2 core, including taking out existing unservicable cable, complete all as specified and directed.

Materials and Labour for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanised steel earth lead wire 4 mm dia. by means of bolts, nuts check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia. MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009)

M/S SR CONSTRUCTIONS

A M CHOUDHURY AND CO

M/S KESHAVE CONSTRUCTIONS

RUPANJAL BORBORUAH

TANKESWAR BORA