Estimate for repair/Renovation of Diyalpura Sub Division Office and Rest house at Sangatiwala.

Amount

Scraping ((a)) White wash and colour wash

Scraping Cement plaster

Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled. ((a)) Doors of area 3 sqm and below.

((b)) Windows of area 3 sqm and below

((c) ) Clerestory windows of area 3 sqm and below

PLASTERING & POINTING 12.5 mm thick cement plaster 1:5

Colour washing (two or more coats)

Finishing walls with cement based water soluble exterior paint such as snowcem, robbiacem etc. two or more coats to give an even shade

Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats over one priming coat to give an even shade

Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consisting of white lead, linseed oil, Varnish, and Chalk Mitti including finishing the surface to required finish complete

Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade

Painting two or more coats with synthetic enamel paints in all shades on old wood work or metallic or plastered or concrete surface to give an even shade including rubbing down old paint.

Providing and installation of PVC Wall Panel complete in all respects

Providing and laying vitrified floor tiles in different sizes in light colour shades made using Soluble Salt Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. ( Soluble salt Print Penetration should be up to 1 to 2 mm after the tiles are fired & polished ). (a) Size 600x600 mm

Hollock wood doors shutter windows shutter including hinges, screws, chocks, cheats, stops cords etc. complete fixed in position. (a) panelled, glazed or glazed and panelled.35 mm thick

Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position (Code : II Revision IS-2191 Part-I) 1973 ((a)) Commercial with elm or gurjan facing on both \ Sides with laminated core and lipped edges:- 35mm thick

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300mm x 16mm

Chowkats of commercial hard wood such as Hollock confirming to ISI specification no 1003 m kiln seasoned of doors and windows including iron hold fasts, corner straps cleats, stops, bolts for hold fasts etc, complete fixed in position (A) Double Rebate (60mm x 150mm)

Wire gauge fixed on chowkats with 25mm thick Hollock wood cover molding of full width.

Fixing wire gauze out side the clerestory window including teak wood chowkats and cover molding

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt) ((ii)) For shutter area above 0.50 sqm

Supplying Pressed steel sheet frames (chowkhat) consisting of 18gauge (1.25 mm thick steel sheet of the specified section, including iron lugs (hold fast) iron hinges conforming to PWD specification including bolts for fixing stops lock notch provision for receiving tower bolts and finished with 1 primer coat approved quality, fixed in position excluding the cost of cement concrete 1:3:6 for fillings in the frame and cement concrete 1:2:4 for lugs complete ((c)) Doors and windows frame of size 151mm x 60mm with 35 mm wide double rebate weighing 3.95 kg per meter.

) Supplying and fixing fan clamps with 50mmx6mm flat iron 50cm long and U-hooks of 16mm diametre M.S. Bars, of approved size with nuts including threading etc. complete in all respects.

First class burnt brick work laid in cement sand mortar 1:3 in first storey upto 4 metres above plinth level.

Providing & laying integral cement based water proofing treatment including preparation of surface

Providing & installation of 2 HP Submerisble motor at site complete in all respects

HEAVY GAUGE WELDED CONDUIT PIPES: Supply & erection of Heavy guage welded conduit pipe (ISI marked) as per IS:9537:Part-II for wiring purposes including bends, junction boxes, Steel hooks, GI saddle clamps and other petty materials etc., where necessary including painting as per PWD General Specifications:- ((xi)) Supply & erection of 19/20mm dia. M.S. conduit pipe (1.6mm thick), White painted suspension rod for ceiling fan.

A) ERECTION of fans: Erection of Ceiling/ Cabin/ Exhaust fan having connection with PVC insulated PVC sheathed two single core copper conductor (FR) cable 0.75sq.mm complete:- ((a)) Erection of Ceiling fan

Erection of light fixtures on wall/ ceiling having connection with PVC insulated PVC sheathed two single core copper conductor (FR) cable 0.75sq.mm complete:- ((a)) Erection of 1X20/28/36/40W Box type (LED/ Fluorescent) light fixture

Providing Ceiling Fan at complete in all respects site

Providing LED Tube Light at site complete in all respects

Providing LED Street Light of 30W at site complete in all respects

Providing Office Chair at site complete in all respects

Providing Office Table at site complete in all respects

Extra rates for white washing, distempering, painting and decorative cement based paints etc for superstructure Where any single storey height exceeding 4 mtr in height for every additional height of 2 mtr or part thereof (External or Internal) (a) for external paint

(b) for internal paint

Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia (ISI Marked) installed on surface etc., complete with PVC boxes (Plastic on surface boxes) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), MS saddle clamp, PVC Circular junction Boxes (Four way 1½" deep for walls), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material and painting as required:- (1) Wiring fan point (Without fan box)

(2) Wiring light point

(3) Wiring 6Amp. Plug control comprising wall socket point

(4) Wiring 16/20Amp. power plug control point

Supply and erection of switches, sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.,:- 1)_ 6/10amp. One Way Modular Switch (One Module)

2) 16/20amp. One Way Modular Switch with Indicator (One Module)

3) 6amp. 2/3 Universal Modular Shuttered Socket (two Module)

4) 16/20amp. Universal Modular Shuttered Socket (two Module)

5) Step type Modular Electronic Fan Regulator 100watts (One Module)

6) Bakelite Batten Holder (Large size)

Supply and erection of Modular Cover Frame (Complete set) on the existing metal box including fixing and connection of existing switches and sockets and other petty material etc:-1) Modular Cover Frame One or Two Module

2) Modular Cover Frame Three Module

3) Modular Cover Frame Four Module

4) Modular Cover Frame Six Module

5) Modular Cover Frame Eight Module

Supply and erection of Concealed Metal Boxes of various sizes (1/2M, 3M, 4M, 6M, 8M, 12M, 16/18M) with brass lugs recessed in wall for mounting modular accessories including fixing and other petty material etc., including the cost of cutting and filling up of chases (with finishing the surface):-1) Powder Coated Concealed Metal Box with Brass Lugs One/Two Module

2) Powder Coated Concealed Metal Box with Brass Lugs Three Module

3)Powder Coated Concealed Metal Box with Brass Lugs four Module

4)Powder Coated Concealed Metal Box with Brass Lugs Six Module

5)Powder Coated Concealed Metal Box with Brass Lugs Eight Module

Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:- 1) MCB Single Pole 6-32amp. (10kA, Curve-C)

2) MCB Four Pole 50, 63amp. (10kA, Curve-C)

SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB's/ RCBO's/ RCCB's: Supply and erection of sheet metal Double Door Distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, colorcoded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:- TP&N Double Door Distribution Board 4way each

PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- 1) Heavy Gauge PVC Conduit Pipe 20mm dia. (On Surface)

2) Heavy Gauge PVC Conduit Pipe 25mm dia. (On Surface)

PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE: Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- 1) Overall size 1sq.mm (Un-sheathed)

2) Overall size 1.5sq.mm (Un-sheathed)

3)Overall size 2.5sq.mm (Un-sheathed)

4)Overall size 4.0sq.mm (Un-sheathed)

DISMANTLING WIRING POINTS & FITTINGS: Dismantling old wiring points including necessary repairs to wall etc:- 1) Fan, light or call bell point

2) Wall socket, power plug point

XLPE INSULATED UN-ARMOURED CABLES (LOOSE): Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:- Overall size 25sq.mm (3½ Core) Unarmoured (Loose)

Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., completewhite cement slurry in joints including corners angles and beading

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS :15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 200 x 300 mm, 100x200mm, 200x200mm as approved by Engineer-in Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing in position Chinaware European type water closet P trap or S trap of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistren, PVC short bend 32mm dia including cost of seat cover complete in all respect and tothe entire satisfaction of Engineer-in-charge.

Providing and fixing jet spray with 2'-6" long PVC pipe with C.P.C. Bras nut

Dismantling sanitary fixtures European/Indian/Orissa W.C.

Providing & fixing in position vitreous Chinware white Indian make flat back or angular lipped front small urinals size 265x315x440mm approved make (to the approval of the Engineer-in-charge) with C.P. brass tube connection 300 mm long complete in all respect. ( Urinal Closet )

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt Screw Pair 115mm long complete in all respect. Size 550 mm x 400 mm x 815 mm

Extra for providing and fixing PVC 32mm waste pipe .

Providing and fixing in position C.P. brass soap dish of approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect.

Cutting holes upto 23cm square for pipes in flooring and roofs of bricks, tiles with lime concrete or cement concrete and making good including repointing, replastering and colour or white washing where required. Through floor or roof 11.5cm thick

Providing & Fixing in position C.P. Brass overhead shower 1 flow without shower arm with 15mm i/d inlet of approved make complete in all respects (as required by the Engineer-in- Charge) C.P. Brass rain fall shower without arm 6" round

Providing & Fixing in position towel rails / rings of approved make (to approval of Engineer-in- Charge) complete in all respects. C.P. Brass towel ring

Providing and fixing in position SS Grating with frame of approved make(to approval of Engineer-in- Charge) complete in all respects

Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass complete with 4mm thick hard board backing fixed in with rawl plugs 50mm C.P. brass screws and washers and s/s studs on top (as required by Engineer-in- Charge) complete in all respects size 550mm x 400 mm

Providing & Fixing in position PVC flexible tube connection of approved make (to approval of Engineer-in- Charge) complete in all respects .PVC tube connection of size 15mm x 300mm with C.P. bras nut

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes lines and making good the same to its original condition. Size 75 mm x 75 mm

Providing and fixing in position SWR UPVC soil waste vent or antisyphonage pipes to I.S.I. 13592 of approved make (to the approval of EIC) including cutting, jointing, wastage, but excluding cost of lead jointing. (1) 110mm i/d SWR UPVC pipe lines laid complete

(2) 90mm i/d SWR UPVC pipe lines laid complete

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes to I.S.I specifications of E.L.C manufacture or any other reputed firm including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining. For 110mm i/d pipes (1) Single Tee With Door

2)Vent Cowls

3)Coupler

4) P Trap/Floor Trap 110mm x 75mm

Providing & Fixing in postion 15 mm i/d bib cock of best quality (as approved by the Engineer-in-charge). C.P. brass Bib cock long nose/long body foam flow without flange

Providing & Fixing in postion 15 mm i/d bib cock of best quality (as approved by the Engineer-in-charge). C.P. brass Bib cock foam flow without flange

Providing & Fixing in postion stop cock / Angle valve (as approved by the Engineer- incharge). C.P.brass 15mm Angle valve

Providing & Fixing in position C.P. Brass extension piece 15mm dia, 15mm long or 25mm long or 50mm long with various fixtures complete in all respects (as required by the Engineer-in- Charge) C.P. Brass extension piece, 25mm long to 50mm long

Providing and placing in position on terrace (all floosr levels ) HDPE water storage tanks of approved make ( to the approval of Engineer in charge) with cover with suitable locking arrangement and making necessary holes for inlet,outlet flow pipes without fitting and base support for tank. Triple layer tanks

Providing and laying jointing fixing and testing G.I pipe lines B-class including cost of specials such as tees bends sockests, elbows etc . Esting, cutting, threading inside building complete (1) 15mm i/d lumsum

(2) 20mm i/d lumsum

(3) 25mm i/d lumsum

Providing, fixing and jointing union coupling in G.I pipe lines (1) (1) 15mm i/d G.I union

(2) 20mm i/d G.I union

(3) 25mm i/d G.I union

Providing and fixing in position GI tank nipple of approved make (to the approval of Engineer in charge) G.I tank nipple 20mm i/d

THE SAHOKE COOP LABOUR AND CONSTRUCTION SOCIETY LTD