CA NO CWE SGNR/TOKEN-40 OF 2022-23 PROVISION OF 01 X MULTI PURPOSE TRAINING SHED IN KLP-I AT MILITARY STATION FAZILKA

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc and n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft loose soil complete all as specified & directed by Engr-in-charge.

Surface excavation n.exc 30cm deep & averaging 15cm deep and getting out in soft / loose soil complete all as specified & directed by Engr-in-charge.

M&L Plain cement concrete (1:3:6) Type C2 (Using 40 mm graded stone aggregate) in as foundations, filling and mass concreting complete all as specified & directed by Engr-in-charge.

Spreading & levelling in layers n exc. 25 cm thick & well ramming incl. watering as required complete all as specified & directed by Engr-in-charge.

Removing excavated soil exc. 250 m but n exc. 500 m and depositing where directed complete all as specified & directed by Engr-in-charge.

Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soft/loose soil complete all as specified & directed by Engr-in-charge.

M&L RCC M-25 design mix as in Foundations, including rafts, footings, foundation beams plinth beams; bases for columns, etc basement slabs, under-reamed piles and mass concrete complete all as specified & directed by Engr-in-charge.

M&L for RCC M-25 Design mix as in Beams, cantilevers, bressummers,lintels over 1.5m span complete all as specified & directed by Engr-in-charge.

M&L for RCC M-25 Design mix as in Columns, pillars, piers, posts and struts complete all as specified & directed by Engr-in-charge.

M&L for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by Engr-in-charge.

M&L for Mild steel TMT bars 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by Engr-in-charge.

Formwork to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits of foundation & plinth beams; and similar work; verticle or to batter Rough finished surfaces of concrete flat complete all as specified & directed by Engr-in-charge.

Formwork to sides of pillars, posts, struts, piers, columns, & stanchions Rough finished surfaces of concrete Square, rectangular or polygonal complete all as specified & directed by Engr-in-charge.

Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat complete all as specified & directed by Engr-in-charge.

S&F Glass dividing strips, 3 mm thick 38mm wide complete all as specified & directed by Engr-in-charge.

M&L for 40mm thick PCC (1:2:4) type B-1, using 20mm graded stone aggregate as in flooring complete all as specified & directed by Engr-in-charge.

M&L for 75mm thick PCC (1:4:8) type D-2, using 40mm graded stone aggregate as in sub base complete all as specified & directed by Engr-in-charge.

M&L for 50mm thick PCC (1:3:6) type C-1, using 20mm graded stone aggregate Finished even & smooth without using extra cement as in plinth protection complete all as specified & directed by Engr-in-charge.

M&L for Hardcore of Broken brick gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface complete all as specified & directed by Engr-in-charge.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats of quality Fe 410_W (GdeE- 250) quality-A complete all as specified & directed by Engr-in-charge.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates of quality Fe 410 -W (GdeE- 250) quality-A complete all as specified & directed by Engr-in-charge.

S&F Mild steel bolts, dia of neck exc 20mm and n.exc 25mm purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. exc 30cm long complete all as specified & directed by Engr-in-charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed by Engr-in-charge.

Providing and fixing 0.71 mm thick Precoated colour or mill finish Aluminium Ridges plain (500-600mm) of alloy IS designation 31500, Aluminium Alloy (AA) 3004 (ISO designation). For colour, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size M6, 60 mm long with 3 mm EPDM seal and SS plain washer complete all as specified & directed by Engr-in-charge.

M&L, for two coats of synthetic enamel paint on steel Surfaces over one coat of priming with red oxide or zinc chromate of any description, over 10cm in width or girth , not other wise described, including preparation of new surface complete all as specified & directed by Engr-in-charge.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified & directed by Engr-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified & directed by Engr-in-charge.

M & L for point wiring complete with 1.5 Sqmm (Nominal area) PVC insulated multustranded (FRLS) unsheathed copper conductor cable with colour code ISI marked and including 20mm dia PVC concealed conduict ISI marked and conduit fittings for one light point/fan point/exhaust fan controlled by one switch including PVC insulated 1.5 Sqmm single core copper earth wire to common earth and connecting to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified & directed by Engr-in-charge. Note: (Cost of MS sunken box and bakelite sheets included in the unit rate of this item).

All as per Srl item No.28 here-in-before but one three pin socket outlet 5 Amps on the independent board.

All as per Srl item No. 28 here-in-before but one three pin socket outlet 5 Amps on the same board.

M&L for point wiring complete with 2.5 Sqmm (Nominal area) PVC insulated multistranded fire retardant low smoke unsheated copper conductor cable ISI marked in and including 20mm dia PVC concealed conduit ISI marked and conduit fitting for 3 pin 15 Amp multipurpose switch socket combination including PVC insulated 2.5 Sqmm single core copper earth wire to common earth and connected to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified & directed by Engr-in-charge.

S&F switch Piano type single pole one way 5 Amp, 230V supply complete all as specified & directed by Engr-in-charge.

S&F socket two in one ,3 Pin 5 Amps, 230V, AC supply complete all as specified & directed by Engr-in-charge.

S&F switch Piano type, single, pole one way 15 Amp 230V complete all as specified & directed by Engr-in-charge.

S&F socket 6 Pin, 16 amp, 230V, AC complete all as specified & directed by Engr-in-charge.

S&F for Ceiling Rose, surface bakelite 2 to 3 terminal, 240 volts, 5 Amp ISI marked complete all as specified & directed by Engr-in-charge.

S & F MCCB TPN suitable for 63 Amp, 415 volts AC supply and short circuit protection and rupturing capacity not less than 25 KA complete all as specified & directed by Engr-in-charge.

S&F Distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting TPN 4 way 415 volts with bus bar rating 200 Amps dust and vermin proof suitable for incorporation of MCBB TPN and isolators etc complete all as specified & directed by Engr-in-charge.

S & F 6 to 32 Amp MCB SP suitable for 240 volts AC supply with over load and short circuit protection and rupturing capacity not less than 10 KA complete all as specified & directed by Engr-in-charge.

S & F 16 to 40 Amps MCB SPN suitable for 240 volts AC supply with over load and short circuit protection and rupturing capacity not less than 10 KA complete all as specified & directed by Engr-in-charge.

S&F Distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting TPN, 8 way, 240 volts with bus bar rating 200 Amps dust and vermin proof suitable for incorporation of MCBB TPN and isolators etc complete all as specified & directed by Engr-in-charge.

S&F LED light fitting 1x18watt 4 feet long including LED tube with driver complete suitable for fixing on wall/roof with body robust, corrosion resistant, superior finish and without any cracks or through holes. The system wattage of fitting should not be more than 18 watt= 10%, surge protection of minimum 2 KV power factor should be more than 0.90 cool while colour, total hormonic distoration (THD) should not be more than 15% lumen output should not be less than 1700 lumens, total input voltage range 140-280V AC, colour rendering index should not be less than 80, Corelated colour should be minimum 6000 degree Kelvin complete all as specified & directed by Engr-in-charge.

S&F sub main wiring of PVC FRLS insulated unsheathed two core 6 sqmm copper multi stranded conductor including one run of single core copper conductor of size 4sqmm as earth wire drawing in and including concealed PVC conduit complete all as specified & directed by Engr-in-charge. Note: Two run of 6Sqmm and one run of 4Sqmm wire including PVC conduct will be measured as one run.

Removal of excavated surplus spoil to a distance n.exc 50m and depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified & directed by Engr-in-charge .

M & L for sand cushioning with dry and clean locally available sand for underground cable 8cm before laying cable and 15 cm after laying cable and punned to 18 cm after laying of cable complete all as specified and directed by Engineer-in-Charge. (Note: Thickness after punning shall be considered for payment purpose)

Supply and laying well burnt clay brick old size class 'B', laid dry flat for cable protection over the cable, length of brick shall be across the length of cable complete all as specified and directed by Engineer - in - Charge.

Supplying, laying, jointing, testing and commissioning16 Sqmm x 4 core XLPE insulated, screened , PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by Engineer in charge. Note: Excavation, earth work, sand cushioning & brick protection will be measured and paid for separtely under respective items of BoQ.

MANCHANDA CONSTRUCTION CO

RUCHIKA CONSTRUCTIONS

N.R.Builders