SPECIAL REPAIRS TO BLDG NO 66 BLDG NO 120 NEAR ATHLETIC GROUND OF RMS AJMER BLDG NO TA 1 AT RMS AJMER PROVN OF ONE TEA ROOM AT RMS AJMER AND SPECIAL REPAIRS FOR REPLACEMENT OF UNSERVICEABLE SOLAR LIGHT FITTINGS AND ALLIED WORKS AT AJMER MIL STATION

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry, concrete or stone masonry surfaces of walls, finished even & smooth without using extra cement, complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:6 on other than fair faces of stone masonry surfaces of walls, finished even & smooth without using extra cement, complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick masonry, concrete or stone masonry surfaces of walls, finished even & smooth without using extra cement, complete all as specified.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick masonry, concrete or stone masonry surfaces of walls, finished even & smooth without using extra cement, complete all as specified.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, chajjas, isolated width etc., finished even & smooth without using extra cement complete all as specified.

Demolition of plain cement concrete in ground floor and pavings not exc 15 cm thick (below or above ground level) including floor tiles of any description, complete, all as specified & directed.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) all as specified & as directed.

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified.

M&L for 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded crushed stone aggregate as in sub base/levelling course of flooring, finished even and fair, complete, all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc., laid and bedded in any mortar.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 20 mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

All as per description of serial item No. 15 above but area of each tile exceeding 0.6 sqm but not exceeding 0.11 sqm each.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 over and including 25 mm thick PCC 1:2:4, type B0 using 12.5mm graded stone aggregate, complete all as specified and directed.

M&L for glazed ceramic tiles (coloured) 7mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed backing in cement & sand mortar 1:4 complete, all as specified and directed.

M&L for 18 to 20mm thick Granite (of any type) slab of approved shade as in steps, jambs, pillars, window cills, cooking platform and the like , bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing as per local trade practice) over & including 15mm thick screed bed (bedding layer) in CM 1:4 all as specified & directed.

Disconnecting and taking down PVC water storage tank of capacity 500 litre to 1000 litre and removing from site, all as directed.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F in repairs 20 mm bore Gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed.

S&F in repairs 25 mm bore Gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed.

S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms) complete all as specified and as directed.

Taking up or down steel water tubing and connections of 15mm bore, fixed in walls, ceiling, floors, trenches etc. all as directed.

All as per description of serial item No. 26.00 above but 20 mm bore pipe.

All as per description of serial item No. 26.00 above but 25 mm bore pipe.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L for galvanized steel water tubing medium grade of 25 mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic WC seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device, complete all as specified & as directed.

S&F in repairs plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device complete all as specified.

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle, PVC connection etc, complete all as specified & directed.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F 15mm bore, pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes.

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed on wall with PVC rawl plug & cadmium plated brass screws, complete all as directed.

S&F in repairs 15 mm bore bib tap, cast copper alloy, ISI marked,chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule.

S&F 15mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F in repairs 15mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F PVC connection, heavy duty 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints, laid in trenches or floor including taking down old pipe, complete all as specified& directed.

All as per description of serial item No. 44.00 above but 75 mm bore pipe.

S&F 75 mm bore PVC (SWR) bend, any radius with access door.

S&F 110 mm bore PVC (SWR) junction single (single ‘T’), equal or unequal with access door.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls including taking down old pipe, complete all as specified& directed.

S&F 75mm bore PVC (SWR) vent cowl.

S&F PVC (SWR) floor trap/multi trap, plain with PTMT grating including jointing with solvent cement, diameter of outlet 75mm, complete.

Taking down chowkat or frame with shutters area exc 1.5 Sqm and not exc 4 Sqm each (without taking off the shutters from the frame) including cutting holes for hold fasts &making good disturbed surfaces of wall in CM 1:3, complete all as specified.

Taking down chowkat or frame with shutters area not exc 1.5 Sqm each (without taking off the shutters from the frame) including cutting holes for hold fasts &making good disturbed surfaces of wall in CM 1:3, complete all as specified.

S&F mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

S&F second class hard wood (Hollock/Bonsum/Sal) factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

S&F factory made 35mm thick glazed and skeleton shutters (three panels) made of second class hard wood, open rebated and prepared to receive glass, gauze etc (witht sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete, all as specified & directed.

S&F factory made solid PVC door frame of size 75mmx45mm made out of 5mm wood grain printed single piece extruded PVC profile reinforced with MS square tube in opening & edges shall be painted to match with printed sheet as per specifications.

S&F factory made solid panel PVC moulded door shutter with particle board core, 28 to 30mm thick (styles) with 2,4 or 6 raised panel design with 2 mm thick moulded PVC sheet on front face & 2mm thick plain colour PVC frame sheet on back face and fixing in frame at site, complete, all as specified & directed.

S&F butt hinges of size 100 mm medium weight, cold rolled mild steel ISI marked, complete, all as specified & directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified

S&F aluminium handle, 150mm size, cast type, anodized (ISI marked) complete all as specified.

S&F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

S&F factory made steel windows/ventilator glazed & gauged (combination) with side hung/top hung shutters including box type/projecting type hinges and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete including AC/cooler opening arrangement in window & guard bars, complete, all as shown in drg No. CEBZ/TD/11 Sheet 1/7 to 7/7.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified.

S&F 3 mm thick figured glass pin headed type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the surfaces, complete all as specified.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane , complete all as specified.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1 mm thick finished coat of white wall care putty, complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for preparation of old plastered or unplastered surface of wall and applying one coat of oil bound (washable) distemper complete all as specified & directed.

M&L for preparation of old plastered or unplastered surface of wall and applying one coat of cement base paint complete all as specified & directed.

M&L for preparation of old plastered or unplastered surface of ceiling and applying one coat of white wash complete all as specified & directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer, complete, all as specified & directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint, complete all as specified & directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic & sand (1:3).

Demolition of plain cement concrete of any description and in any position not otherwise specifically provided for in this Schedule complete all as specified.

M&L for cement concrete (1:3:6) type C1 using 20 mm graded crushed stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement. Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc. (Note: Only Inner girth shall be measured.)

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting exc 10 cm but not exc 20 cm girth in brick walls.

M&L for 10 cm thick sand stone slab in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc not exc 2m in length, punched dressed on face and along exposed edges, self faced on the other side and set and pointed in cement mortar 1:4 complete.

S&F in repairs Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats, complete, all as directed. (Minimum weight 190gms)

S&F Bottle trap 32 mm bore of PTMT having minimum water seal of 25mm, complete, all as directed .(Minimum weight 260gms)

Complete removal of existing roof treatment of any description including cement plaster/concrete of any thickness from roof surfaces, cleaning of roof surfaces and preparing it for further treatment and removing rubbish from the site up to 50 m , complete, all as directed.

M&L for rendering 10mm thick in cement mortar 1:4 on roof top surfaces, mixed with water proofing compound as per manufacturer's instruction, finished even & smooth without using extra cement, complete, all as specified & directed.

M&L for APP modified polymeric water proofing membrane, 2 mm thick having centre core not less than 100 micron high molecular high density polythelene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3 Kg/Sqm applied with bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.2 Kg/Sqm over bitumen primer conforming to IS-3384 @ 0.40 Kg/Sqm with final coat of bonding bitumen grade 85/25 @ 1.2 Kg/Sqm over APP membrane with all overlaps, complete, all as specified & directed.

M&L for 40mm thick (average consolidated thickness) type B0 using 12.5mm graded stone aggregate as in padding even and smooth without using extra cement with existing slope with 'V' shaped grooves 6mm wide and 10mm deep @ 1.2m interval or part thereof, both ways on top of padding and filled with mastic bitumen of 1:1 proportion, complete, all as specified & directed.

S&F in repairs aluminium door shutters with frame of aluminium section weighing not less than 0.55 Kg/RM including necessary joining cleats, glazing clips, rubber neoprene packing, brass handle and brass tower bolts of size 150mmx 02 Nos in each door, hinges, anodised aluminium snap beading screws, hydraulically regulated double action floor spring made up of 1.25 mm thick aluminium alloy sheet, foundation box for each shutter etc and including fitted with 5 mm thick tinned glass in glazed shutter with brass mortice lock of 100mm , 2 levers, vertical type, complete, all as specified in clause 10.37 of SSR Part I & directed by Engr-in-Charge.

S&F in repairs 22 mm bore MS powder coated tubular curtain rail, fixed to PVC rawl plugs with chromium plated brass screws, complete, all as specified & directed.

S&F decorative type end knobs with brackets for fixing curtain/pelmet rod, complete, all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness, including cover fillets.

Providing & fixing false ceiling with fibre cement designer tile Ivory painted (High pressure steam cured) of 4mm thickness (As per IS: 14862) of size 595x595mm and any one of the design (Oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (Galvanised @ 120 Gms, both side inclusive) consisting of Main ‘T’ runner with suitably spaced joints to get required length and 15x32mm made from 0.3mm thick sheet, spaced at 1200mm C/C and cross ‘T’ of size 15x32 mm made of 0.30 mm sheet, 1200 mm long spaced between main ‘T’ at 600 mm C/C to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600mm and size 15x32mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 15x20mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including, required cutting/making, opening of services like diffusers, grills, light fittings, fixtures, smoke detectors etc main ‘T’ runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rod of 3mm dia with galvanised butterfly level clips, spaced at 1200 mm C/C along main ‘T’ bottom exposed width of 15mm of all ‘T’ sections shall be centra black pre-painted with polyester paint and having a load bearing capacity of 12 Kg/Sqm, complete at all heights as directed by Engr-In_charge. Make :- Everest/Armstrong

Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc including ridges complete all as specified.

Dismantling timber scantlings 40 sqcm and over in section, in any position, framed work

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins etc. under 40 sqcm in section, framed work

Dismantling framed trusses of span not exc 10 m long.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, rafter and battens of angle or oter sections with gusset plates, rails, braces etc including distance pieces, cleats, necessary welding etc. conforming to Grade E-250 quality `A’ all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thick of an colour having tensile strength of 550 MPs as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified & directed..

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet for ridges of 0.50mm thick of an colour having tensile strength of 550 MPs as in roof covering fixed with self tapping screws, complete all as specified & directed..

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted stone masonry built in cement mortar 1:6 complete all as specified & as directed.

All as per description of serial item No. 96.00 above but except stone.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, hammer dressing with maximum depression on face from straight edge held against the dressed surface not exc 20mm, lime or sand stone.

M&L for sand stone as in quoins, jamb stones, door or window heads, plain corbels, door cills, plain steps, parallel copings with throated edges, complete as directed.

Extra over for external angles (for quoins and jambs) in facings for walling of random rubble or polygonal rubble, uncoursed or brought upto courses and squared rubble masonry, regular coursed, Secunderabad and Bangalore, complete, all as directed.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4, complete, all as specified & directed.

Taking down shutters of any description not exc 1 Sqm each.

Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each.

M&L for machine cut Kota stone slab flooring 20 to 25mm thick & 550x550mm size, laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete, all as specified & directed.

M&L for machine cut Kota stone slab 20 to 25mm thick on vertical surfaces such as dado, skirting, cills etc. laid over & including screed bed or bedding layer of 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete, all as specified & directed.

S&F mild steel framed work using ERW or induction butt welded tubes conforming to I.S 1161-1979 Grade St-240 including necessary welding, bolting, special shaped washer, clamps, cleats etc. complete all as specified & as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

S&F mild steel framed work such as grills, guard bars, barred iron doors, cooler stand, framework of water tanks and similar works, conforming to Grade E-165 (Fe 290), including welding etc. complete all as specified & as directed.

S&F in repairs brass chromium plated wall mixer with 'L' bend for mixing hot & cold water screwed down for iron pipe of 15mm bore all as specified and as directed.

S&F factory made pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, mild steel sheet of 1.25 mm thickness, complete as specified & as directed.

Excavation in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes etc not exc 10 Sqm on plan and getting out in any type of soil, complete, all as specified & directed.

Removal of excavated material (soil) n.exc 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified & directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate in foundations, filling and mass concrete.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M&L for 40mm thick PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in damp proof course on horizontal surface using water proofing compound including necessary formwork. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Earth filling under floors including spreading, leveling, watering and well ramming in layers not exc 25 cm thick. Note :- Soil obtained from excavation under serial item No. 106 here-in-before shall be used for filling under floors.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

All as per serial item No. 118.00 here-in-before but 8mm dia.

M&L for reinforced cement concrete 1:1.5:3 (Nominal mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like, complete, all as specified & directed. .

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete, complete, all as specified & directed.

M&L for reinforced cement concrete 1:1.5:3 (Nominal mix) using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like, complete, all as specified & directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete, complete, all as specified & directed.

M&L for reinforced cement concrete 1:1.5:3 (Nominal mix) using 20mm graded crushed stone aggregate in lintels over 1.5m clear span, seismic and other similar bands, lintel bands, plinth bands, roof bands and the like, complete, all as specified & directed.

Formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete, complete, all as specified & directed.

M&L for reinforced cement concrete 1:1.5:3 (Nominal mix) using 20mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like, complete, all as specified & directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete, complete, all as specified & directed.

Formwork to edges of concrete flats, roofs, floors etc and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces, complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash, complete, all as specified & directed.

S&F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 100 gms).

S&F factory made steel window/ ventilator factory made made out of MS hollow section 79 mm x39 mm x 1.6 mm thick frame with double shutter (glazed & wire gauzed shutter) made out of 'Z' section using flush butt welding and tennon riveting, all as per IS 1038/83, dobby hinges shall be provided to both shutters, locking arrangements, 25mm aluminium knobs to shutter, aluminium hook & eye, 10mm MS square bars in grill, 04 Nos lugs welded to frame 'Z' section handle, 100 mm including necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4, type B1 including two coat of synthetic enamel paint over a coat of zinc crome/red oxide primer, complete, all as specified & directed. Note:- Wire mesh and sheet glass shall be measured and paid separately. with top hung shutter including hinges, steel peg stay, handle complete all as specified.

Supply only integral water proofing compound (ISI marked).

M&L for 40mm thick sand stone slabs, set and jointed over joist etc in CM 1:4 as in base of water tank including 25mm thick PCC 1:2:4, type B0 using 12.5mm stone crushed aggregate (for providing bottom base of PVC tank) complete, all as specified & directed.

S&F sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink.

S&F 15 mm bore fancy type, long body bib tap, full turn, with wall flange, cast copper alloy with capstan heads, chromium plated, screwed for iron pipe or for brass ferrule, complete all as specified & as directed.

M&L for 18/19mm thick block board, Grade 2 quality, interior grade, commercial type and both faces covered with approved pattern decorative coloured laminate type 1 of 0.9mm thick and all around side faces is covered with decorative lipping, complete as in cup board shutter and fixed with wooden frame work, complete, all as specified & directed.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screws.

Supply & fixing hasp and staple of size 100mm aluminium anodized safety type with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, multi stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick( Make - Hylem/Anchor) ISI Marked, brass screws and cup washers including 1.5 Sqmm multi stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed for:- Make of wire- Havells/Polycab/Anchor/Finolex. Make of PVC conduit -AKG/Plaza/Kalinga

One light point/bell point controlled by one, one way switch.

One ceiling fan/exhaust fan point controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One 3 pin 5 Amp socket on independent board.

All as per item No. 141 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm Multi stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F Switch piano, flush type, single pole, one way, 5 Amps, 240 volt, 50Hz, AC, complete all as specified and as directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F switch piano flush type 15 Amps, single pole one way 240 volts complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F bell push flush type 5 Amp complete all as specified and directed.

S&F Socket outlet 3 Pin 5/6 Amp flush type complete all as speciied and directed by engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F socket out let 2 in 1, multipurpose 3 pin 15/16 Amp flush type complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F ceiling fan regulator electronic flush , steped type (four step) 230 Volts AC complete all as specified and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F ceiling rose surface bakelite 3 terminals complete all as speciied and directed by Engr-in-Charge .MAKE:-Havells/Anchor/Legrand

S&F bell ding dong type, AC, 230 volt, single pole complete all as specified and directed. .MAKE:-Havells/Anchor/Legrand

S&F lamp holder PVC/polycarbonate type with back plate complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F of LED lamp 9/11 watt complete all as specified and directed.. MAKE:-Havells/Anchor/Legrand

S&F LED tube light fitting retrofit batten in acrylic linear tube single LED tube light including 1 x 20 W LED retrofit bar professional CW 6500 K cover channel, bipin holders, LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling (1x 20 watt), 230V for rose complete all as specified and directed. Make: Crompton Cat No LTTB-20 & IGP161LT8-16 or equivalent fromPhilips / Bajaj

S&F aesthetically designed linear LED mirror light fitting 10 Watt provided with a high output PMMA diffuser for glare free light complete with all accessories pre-wired and including connecting flexible copper conductor cable with suitable size. Make : Crompton Cat Part No. LCL-07-CDL or equivalent model of Havells/Syska

S&F wall mounted decorative luminarie fitting suitable up to 10 Watt LED lamp B-22 base, complete, all as directed. Note: LED lamp shall be measured separately.

S&F LED light fittings, 1x 10 W bulk head luminaries, with lamp etc complete with all accessories and including connecting up with three core copper conductor cable of suitable size of 230V, 50 Hz, complete all as specified and directed. Make: Bajaj Code No BIBWP 10W LED or equivalent from Havells /Crompton greaves

Supply & fixing, testing and commissioning energy saving street light luminaire 15 watt LED , aluminium pressure die cast housing with tughened glass cover with individual LED lence , IP 66 protection complete all as specified and directed by Engr-in-Charge. Make-Bajaj Cat No. BCLST 15W LED or equivalent model of Surya/Havells/C & S.

S&F street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

Taking down existing electric meter and refixing the same, connecting, testing and sealing properly and making good disturbed surface of wall, all as directed.

Taking down existing ceiling fan/exhaust fan, dismantling blades and refixing after cleaning incl connecting up with three core flexible cable from ceiling rose to fan complete all as specified and directed.

S&F MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed. Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

All as per description of serial item No. 161.00 above but 4 way.

S & F of MCB SP, 240 volt, 3 Amp to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge. . Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge by Engr-in-Charge. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh, PCC chamber in cement concrete 1:3:6 type C-2 and RCC 1:2:4 type B1 cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing, complete, all as specified & directed.

S&F wall fan 400 mm sweep, AC 240 Volts with electric cable and plug top, complete, all as, specified & directed.

S&F ventilating fan 250 mm sweep suitable for 230 Volts, Single phase 50 Hz AC supply, metal body with bird guard including connecting with three core flexibale copper cable. Make Bajaj/Usha / Crompton/Havells

S&F 9 watt LED solar light fittings, IP 65 complete with all accessories including taking out old unserviceable solar light fittings, any watt, complete, all as specified and directed by Engr-in-Charge

M&L for painting of solar light pole up to 1.5mtr height with two coats of aluminium paint including preparation of surface by scraping out old paint and making the existing surface rust free including marking pole numbers/writing letters or figures (block, Roman in yellow circle ), complete, all as directed by Engr-In-Charge.

S&F battery box made up of 20 SWG MS sheet, hinged type as per exising design and size with locking arrangement with suitable clamps, nut bolt and washers etc. including taking out old unserviceable /broken solar battery box and complete all as specified and directed by Engr-in-Charge

S&F GI tubular pole of 80 mm bore, heavy grade, 6 Metre in height including mounting arrangement for panel/battery light, excavation and earth work, PCC work with PCC 1:3: 6 type C-2 using 20 mm graded stone aggregate of size 300 mm X 300 mm dia and 300 mm in height for coping (including necessary plastering to exposed surface with CM 1: 4) including taking out old unserviceable rusted GI tubular pole and complete all as directed by Engr-in-Charge

S&F polycrystalline PV solar panel, 12V, 100 watt aluminium frame design all as specified and directed by Engr-in-Charge including taking out old unserviceable /broken solar panel.

Supply, jointing and testing PVC insulated round sheathed cable with stranded copper conductor, 1 sq mm 2 core with fitting accessories complete drawn through pipe poles including taking out old unserviceable Cable all as specified and directed by Engr-in-Charge

Supply, installation, jointing and testing of 12 Volt, 100 Ah solar tubular battery with minimum warranty of 2 years taking out old unserviceable battery of any size and capacity, complete all as specified and directed directed by Engr-in-Charge. Make: Exide/Luminious

M/s Kishan Gopal Agarwal