SPECIAL REPAIR TO SEWAGE LINE AND MANHOLE OF OR SINGLE LIVING ACCN (PERSONAL LINE) AND CERTAIN REVENUE AND MINOR WORK AT VARIOUS LOCATIONS UNDER AGE B/R-II OF GE BENGDUBI MIL STN

Amount

SCHEDULE 'A'

Surface dressing n. exc. 15 cm deep in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.50 mtr wide and not exceeding 1.5 mtr deep for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc and getting out in soft/loose soil complete all as specified.

Ditto all as per item no. 2.00 here-in -before but exceeding 1.5m deep and not exc. 3.0m deep

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n.exc 50 m and making good surface for soft/loose soil.

Removing excavated material (soil) to a distance exc 50m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm thick in soft / loose soil complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling & mass concrete complete all as specified and directed.

M&L for PCC 1:2:4 type B-2 (using 40mm graded crushed stone aggregate) as in foundation filling & mass concrete complete all as specified and directed.

M&L hardcore of broken stone or boulders gauge n exc. 63 mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for Applying ATT on the bottom and sides of excavation at the rate of 5 Lits of Emulsion per sqm of surface area complete as per manufacture's and applicator,s instruction complete all as specified and directed.

M&L for Applying ATT on the top of surface of filled earth at the rate of 5 Lits of Emulsion per sqm of surface area complete as per manufacture's and applicator's instruction complete all as specified and directed.

M&L for Applying ATT on the soil under plinth protection at the rate of 5 Lits of Emulsion per sqm of surface area complete as per manufacture's and applicator's instruction complete all as specified and directed.

Demolition of brickwork masonry built in cement mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles all as directed.

M&L for Fly ash brick work with old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Ditto all as per item No.15.00 here-in-before but except brick

M&L for brick work with fly ash brick, straight or curved built in CM 1:4 as in half brick thick walls complete all as specified and directed.

M&L for Fly ash brick work with old size bricks, straight or curved on plan to any radius one brick thick honey comb walling built in In cement mortar 1:4 complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in copping, roof kerbs or mud stops, rounded or chamfered on edges and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for 40 mm thick PCC 1;2;4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in Damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for Applying evenly a coat of blown type bitumen at the rate of 1.50 Kg per square metre and blinding with clean dry sand @ 0.05 CUM per Sqm complete all as specified and directed.

Use & Waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rough finished surface of concrete complete all as specified and directed.

Use & Waste of formwork to chullah hoods, chajjas, troughs and similar items including edges, rough finished surface of concrete complete all as specified and directed.

Use & Waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions, rough finished surface of concrete complete all as specified and directed.

Use & Waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick in rough finish of concrete surface etc., complete all as specified and directed.

Use & Waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc rough finished surface of concrete complete all as specified and directed.

M&L for R.C.C M-25 (Design Mix) using 12.5 mm graded crushed stone aggregate for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc., basement slabs, under-reamed piles and mass concrete etc all as specified and directed.

M&L for R.C.C M-25 (Design Mix) using 12.5 mm graded crushed stone aggregate for Columns, pillars, piers, posts etc all as specified and directed.

M&L for R.C.C M-25 (Design Mix) using 12.5 mm graded crushed stone aggregate Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc all as specified and directed.

M&L for R.C.C M-25 (Design Mix) using 12.5 mm graded crushed stone aggregate Chajja etc all as specified and directed.

M&L for R.C.C M-25 (Design Mix) using 12.5 mm graded crushed stone aggregate Beams, cantilevers, bressummers, lintels over 1.5m span etc all as specified and directed.

M&L for TMT bars (Fe-500/ Fe-550D) 10 mm dia & over, cut to length, bent to shape required, including crancking, bending spirally for hooping for columns, hooking ends & binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

All as per item No. 32.00 here-in-before but 5 mm dia and over upto and including 10 mm dia in stirrups, spaces and binders complete all as specified and directed.

M&L 100mm thick PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in subbase/flooring complete all as specified and directed.

M&L 100mm thick PCC 1:2:4 type B-2 using 40mm graded crushed stone aggregate as in flooring, finshed even and smooth without using extra cement complete all as specified and directed.

M&L 75mm thick PCC 1:2:4 type B-2 using 40mm graded crushed stone aggregate as in flooring, finshed even and smooth without using extra cement complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protections, finished even and smooth w/o using extra cement with joints 10 mm wide and in full depth at corners and @ 3.0 m c/c filled with mastic mortar complete all as specified and directed.

M&L 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in flooring, finshed even and smooth without using extra cement complete all as specified and directed.

S&F roof trusses (farmed), trusses purlins, crane gantries, rails and fastenings and heavy bracket framing MS tubes and angles medium grade as in truss, purlin, rafters, post etc fixed with and including angle cleat , MS plate etc including necessary welding, fittings etc Fe-410-W (Gde-E-250 quality-A) complete all as specified and directed.

M&L Joist, channel, angle, tee or tubular sections, fixed independently, without connecting plates, etc.for post (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming Fe-410W(GdeE-250) quality B complete all as specified and directed.

M&L for Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks, training aids and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. Fe-410- W(Gde- E-250) quality- B complete all as specified and directed.

M&L for Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, including necessary riveting/welding complete all as specified and directed by Engr-in-Charge conforming Fe-410W(GdeE-250) quality B complete all as specified and directed.

M&L for rolled mild steel works in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes including screw bolt with hexagonal at one end and screwed with washer and nut fitted Fe-410W(GdeE-250) quality B complete all as specified and directed.

M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 Fe-410W(GdeE-250) quality B complete all as specified and directed.

S&F Pre-painted coloured trapezoidal profiled Galvalume / Zincalume sheet with min thickness of 0.50 mm TCT confirming to IS-513 (AZ-150 GSM, AI Zn alloy mettalic coating with 550MPA yield stress as per AS-1397) as in roof covering/cladding to wall fixed with self tapping screws colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron poyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling self tapping fastener (12-14 x 55 with EPDM seals) complete as specified etc complete all as specified and directed.

S&F Pre-painted coloured plain Galvalume / Zincalume sheet with min thickness of 0.60 mm TCT confirming to IS-513 (AZ-150 GSM, AI Zn alloy mettalic coating with 550MPA yield stress as per AS-1397) as in roof ridge colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron poyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling self tapping fastener (12-14 x 55 with EPDM seals) complete as specified etc complete all as specified and directed.

Dimantling of Asbestos cement (corrugated ted, semi corrugated, etc.) sheets in roof coverings including ridges etc complete all as specified and directed.

S&F 6 mm thick Asbestos cement, corrugated or semi corrugated sheets in roofs, walls etc fixed with 'L' type or 'J' type or cranked hook bolts etc complete all as specified and directed

Ditto all as per item No. 48.00 here-in-before but except Asbectos sheets only.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation oards/slabs/ blankets, any thickness including cover fillets etc complete all as specified and directed.

S&F 6 mm thick plain Non asbestos fiber cement building boards, fixed or laid /inserted to timber /GI /Aluminium frame-work with screws complete all as specified and directed.

S&F of Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof truss/purlin/rafter by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

Demolition of cement concrete (un-reinforced ) of any description & in any position not specifically provided for complete etc complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick in CM 1:6 for laying floor finishes complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surface as backing coat coat of dado/skirting etc complete all as specified and directed.

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exc 0.18 Sqm but n.exc 0.38 Sqm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match etc complete all as specified and directed.

Ditto all as per item No. 57.00 here-in-before but in vertical surfaces such as dado/skirting complete all as specified and directed.

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick, (square / rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match etc., complete all as specified and directed.

M&L Glazed ceramic tiles coloured 300mmx 450mm, 6 to 7 mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) exc. 1.5 sqm and n.exc 4 sqm each and refixing in same position etc complete all as directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Cutting holes in brick walls built in cement mortar for inserting holdfasts and making good dismantled portion in PCC of 1:2:4 B0 using 12.5mm graded crushed stone aggregate in hold fast including necessary form work fair finished of concrete and making good with existing surface as required exc half brick but not exc one brick complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) etc complete all as specified and as directed

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed (Notes : WPC shall be measured and paid seperately)

Supply only water proofing compound (Liquid) complete all as specified and as directed.

M&L for preparing new plastered on wall and applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatement of wall and appying two coat of oil bound distemper over a coat of alkali resistant priming paint etc complete all as specified and directed.

M&L for newly plastered surface of wall appying two coat of white or tinted oil bound distemper over one coat of alkali resistant priming paint etc., complete all as specified and directed.

M&L for two coat of wall care putty on wall including preparation of surface with sand paper etc to obtain smooth surface etc., complete all as specified and directed.

M&L for preparing newely plastered surface of wall alkali resistance primer and applying two coat of cement base paint etc., complete all as specified and directed.

S&F 1.25 mm thick pressed steel frame of size 165 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc., complete all as specified and directed.

S&F 1.25 mm thick pressed steel frame of size 105 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc., complete all as specified and directed.

S&F hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M/L for 35 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides knil seasoned and chemically pressure treated with antitermited complete all as specified and directed.

S&F for 35 mm thick well seasoned 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) etc complete all as specified and directed.

S&F factory made solid panelled PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails.MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail and bottom rail ,panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet bedding and joint together with solvent cement, etc complete all as specified and directed.

M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 etc complete all as specified and as directed

Supply and fixing 4 mm GI wire Galvanised mild steel plain wire to hold fast for hanging of mosquito net complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainles steel wire stapel etc complete all as specified and directed.

S & F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, devetailed or welded complete all as specified and directed.

Ditto all as per item No. 82.00 here-in-before but without glazing bars (for mosquito proof shutter )

S&F in repair steel ventilator with top hung shutter including hinges steel peg staycomplete all as specified and directed.

S&F 3mm thick plain glass of ordinary quality and glazing with oil putty or wooden beading to wooden frame or steel frame in squares n exc 0.50 sqm in each pane complete all as specified and directed.

S&F 4mm thick one side frosted glass of ordinary quality and glazing with oil putty or wooden beading to wooden frame or steel frame in squares n exc 0.50 sqm in each pane complete all as specified and directed.

S&F of Aluminium anodised, 200 mm barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F of Aluminium anodised, 150 mm barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F of 150 mm Aluminium handles, cast type, anodised complete all as specified and directed.

S&F of 100 mm Aluminium handles, cast type, anodised complete all as specified and directed.

S&F 100mm butt hinges medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F 75 mm butt hinges stainless steel and fixed complete all as specified and directed.

S&F 300 mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing and sliding bolt of extruded section and fixed to any type of shutter with screw complete all as specified and directed.

M&L for preparation of new and previously un-treated wood and wood base surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described for two coat of Synthtic Enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F in repair white vitreous china wash basin white flat back size 550x400 (Oval shape) excluding taps but including 32 mm dia chromium plated waste fitting and PVC waste pipe 610 mm long and MS brackets complete all as specified and directed.

S&F, Vitreous china wash down water closet European type (pedestal pattern) (excluding flushing cistern and flush pipe) including connection to outgoing pipe and seat cover and flushing pipe complete all as specified and directed. (Make: Hindware or Parry)

S&F in repair PVC valveless double syphonic action type flushing cistern low level of 10 Ltr capacity white with inlet ball valve, float, flushing bend & handle including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet including brackets & connection to pipe etc complete all as specified and directed.

S&F vitreous China squatting pan, `Orissa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F Vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urianl against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe complete all as specified and directed. (Make: Hindware or Parry)

S&F in repair chromium plated shower roses 125 mm size with or without swivel joints of standard size including fixing to 15mm steel pipe or union complete all as specified and directed.

S&F in repairs 15 mm bore pillar taps fancy type (long neck) cast copper alloy with capstan heads chromium plated screwed down high pressure with or without letter hot or could with long screwed and shanks and fly nuts screwed for iron pipes complete all as specified and directed.

S&F in repair bib tap fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and directed.

S&F in 15 mm Stop valves, cast copper alloy with chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) complete all as specified and directed.

S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed.

S&F in repair tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and as directed

S&F Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F in repairs, 15 mm dia 450 mm long PVC connection pipe with two PVC PTMT nuts at each ends with rubber washer complete all as specified and directed.

S&F medium grade galvanized steel tubing (concealed) with all fittings & fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and directed.

Ditto all as per item No.111.00 here-in-before but 20 mm dia bore of pipe.

S&F rotational moulded PVC water storage tank 500 ltrs capacity conforming to IS-12701(1989) cylindrical vertical type double-layered with closed top including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc complete all as specified and directed.

S&F rotational moulded PVC water storage tank 1000 ltrs capacity conforming to IS-12701(1989) cylindrical vertical type double-layered with closed top including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc complete all as specified and directed.

S&F in repair of Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 20 mm iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair of Ball brass valves,high pressure, with polythene float and flynut complete, screwed for 20 mm bore iron pipe or brass ferrule and fixed complete all as specified and directed.

Demolition of reinforced cement concrete of any description complete all as specified and directed.

M&L for Precast RCC 1:2:4 type B1 as in manhole cover including necessary form work set in cement mortar 1:4 complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings not exc. 15cm thickness below or above ground level complete all as specified and directed.

M&L for PCC 1:2:4, type B-1 (20mm graded aggregate as in kerbs, mud stops, benching and similar work complete all as specified and directed.

M&L for providing Plain Cement Concrete (1:3:6) type C1 using 20mm graded stone aggregate as in surface channel and drain complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth using extra cement including forms moulds, mitred/stopped ends etc complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar pipe of any position and of internal dia of pipe 150 mm including demolition of PCC, and removing dismantled material where directed at a distance n exc 50 m complete all as specified and directed.

Ditto all as per item No.123.00 here-in-before but 200 mm internal bore dia of pipe.

M&L for PCC 1:3:6 type C2 as in bed to drain pipe including packing under haunching against sides of pipe after laying in trenches for 150 mm dia bore drain pipe including testing complete all as specified and directed.

Ditto all as per item No.125.00 here-in-before but 200 mm bore drain pipe.

S&F 150 mm dia SGSW pipe grade 'A' laid in trenches including jointing with cement mortar 1:1 complete all as specified and directed.

M&L Reinforced concrete pipes of bore of pipe 200mm, class NP2, laid and jointing with cement mortar 1:1 complete with collars complete all as specified and directed.

Cutting into existing manhole for connecting new drain pipe of 150 mm bore and making good the pipe and rendering disturbed surface where drain pipe have been inserted cutting out existing benching for forming branch channel (1/2 round or 3/4 round as required) in cement concrete 1:2:4 type B1 and finished the surface even and smooth and reforming benching as required complete all as directed.

All as per item No. 129.00 here in before but 200 mm internal dia of pipe.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required

S&F 100 mm dia cast iron (sand cast) soil waste and vent pipes in any length fixed with cement joints laid in trenches or in floor complete all as specified and directed.

Ditto all as per item No.132.00 here-in-before but fixed in wall

S&F cast iron bend (Sand cast) of any radius with oval access door including jointing with cement joints for (100 mm bore) complete all as specified and directed.

S&F cast iron Bends (any radius) with duck's foot or heel rest of 100 mm bore for jointing to cast iron pipe etc complete all as specified and directed.

S&F cast iron Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches jointing with cast iron pipe etc complete all as specified and directed.

Taking down PVC drain pipes ( any size or pattern) including all fittings head shoes etc complete all as specified and as directed

S&F 110mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints fixed to walls

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed

S&F 110mm bore PVC (SWR) `P' or 'S' trape complete all as specified and directed

S&F 110mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and directed

S&F 75 mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F grating doom 100mm dia of PTMT (minimum weightt 25 gm) for floor trap/nahani trap complete all as specified and directed.

Desludging of 150 mm dia sewage line by roading or by other means from adjacent manhole complete all as directed.

Ditto all as per item No.146.00 here-in-before but 200 mm.

Disludging gully trap by taking out sludge and foreign materials and excavating a pit of appropriate size depositing sludge in the pit and covering with 30 cm thick layer of soil to cover the sludge including removing surplus soil where complete all as directed.

Ditto all as per item No.148.00 here-in-before but from manhole of depth n exc 1.50m deep

Ditto all as per item No.148.00 here-in-before but from manhole of depth exc 1.50m deep but n exc 3.00m deep

Ditto all as per item No.148.00 here-in-before but from manhole depth exc 3m deep but n exc 4.50m deep

Cleaning & clearing of septic tank mechanically with combined high pressure water jetting cum suction (vacuum) type machine mounted on LCV/HCV and having facilities of high pressure water thermoplastic fiber braided water jetting hose and through conical/round shape nozzler pipe and flushing after cleaning including removing the deposited sludge/ solid/ liquid material, outside MD land, complete all as specified and directed.

Demolition of unserviceable floor trap/nahani traps / broken gully trap floor trap of any description and removing material from site complete all as specified and directed.

Material and labour for sub main wiring with two single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 4 sqmm and one single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 4 sqmm as in continuous earth wire drawn into and including concealed PVC conduit medium grade suitable dia 25mm complete with fittings all as specified and as directed.

Material and labour for point wiring for one light controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable and CI/pressed steel terminal box with 3.00 mm thick laminated sheet cover fixed on Wall for earth continuity wire, connected to earth dolly.

All as per Item No 155 above but for one ceiling / exaust fan/ wall fan point controlled by one switch.

All as per Item No 155 above but for one three pin switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per Item No 155 above but for one three pin switch socket outlet, 5 Amp on same board all as specified and as directed.

All as per Item no 155 here-in-before but for one 15 Amp 3pin switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire all as specified and as directed.

All as per Item No 155 here-in-before but for one AC/ Gyser, independent with 4 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 4 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire all as specified and as directed.

S&F switch piano flush button single pole 5 Amps 230 volt one way complete all as specified and directed.

S&F Switch Socket Combination 3 Pin 5/6 Amp, Flush Piano Universal Type, controlled by One Switch, conforming to IS and/or as approved, complete all as specified and as directed.

S&F Switch Socket Combination 6 Pin 5/15 Amp, Flush Piano Universal Type, controlled by One Switch, conforming to IS and/or as approved, complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite three terminals all as specified and as directed.

S&F ceiling fan regulator electronic stepping type, SP 230 Volts, suitable for 1200 mm/1400 mm sweep ceiling fan including necessary electric connection complete all as specified and directed.

Supply and fix LED Neo tube light fitting of 1X18 W with tube (4 Ft) 240 V Wall mounted LED battenUltra bright LED polycarbonate Tubelight with very high efficacy suited for installation in existing T8 tubelight with G13 lamp holders to give glare free light.complete with all accessories internally pre-wired and inclg connection. Make :Crompton/Havells/Bajaj/CG/Phillips.

S&F Bldg security light fittings 1x 15W New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP66 roadway luminaire with high power LEDs as light source and electronic driver with 1.5 M long and PC Cover having TOP OPENING eperate driver compartment all as specified and directed. Make Crompton/ Havells/ bajaj/phillips/CG.

S & F Lamp holder insulated body PVC/ polycarbonate with back plate and 7 W LED bulb suitable for batten fitting complete all as specified and directed.

S&F steet light bracket made out of 32 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete including taking down unserviceable one all as specified and directed.

S & F sheet metal enclosure for DB’s single door 8 way 240V, all complete as specified and as directed suitable for fixing MCB’s with 200 AMPs busber.

S&F MCB Single pole and neutral 240 Volt 20 to 40 Amp capacity complete all as specified and directed.

S&F MCB Single pole 240 Volt 6 to 32 Amp capacity complete all as specified and directed.

S & F Lamp holder insulated body PVC/ polycarbonate with back plate and 7 W LED bulb suitable for batten fitting complete all as specified and directed.

Materials and labour for earthing complete with galvanised earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground (earth pit not less than 2.25 mtr below normal ground level with top edge of the plate not less than 1.50 mtr below normal ground level connected to galvanised earth lead wire of 4.00 mm dia by means of bolts, nuts and washers and check nuts of galvanised iron or steel GI earth strip protected by 40 mm medium grade galvanised iron pipe including of 20 mm dia medium grade GI water tubing sheet metal 4mm wire mash funnel, charcoal or coke and common salt in paint and testing on completion as shown on electrical plate No.5 ofm SSR Part-I. including taking out unserviceable one.

Supply and fixing Ceiling fan of Size 1200mm sweep, 230 volt Ac with connection from existing celing rose with MS hooke for hanging of suitable size all as specified and as directed Make :-Polar/Havells/Bajaj.

Supply and fixing wall mounting hi-flow and heavy duty fan with all accessories of Size 400 mm sweep, 230 volt Ac with connection from existing celing rose all as specified and as directed Make :- Crompton/Polar/Havells/Bajaj.

Supply and fixing PVC Exhaust fan of Size 250 mm sweep, 230 volt Ac with connection from existing celing rose with Louver Shutter all as specified and as directed Make :- Crompton/Polar/Havells/Bajaj.

M&L for laying XLPE insulated, armoured heavy duty electric cable in trenches/floor/walls/pipes with aluminium conductor, 1100 volts grade, cross sectional area 16 Sqmm 2 core multistranded. complete including necessary cable glands, aluminium lugs duly crimped, termination etc all as specified and directed.

M&L sand cushioning (dry) in trenches for protection of UG cables (below, above and around the cable laid in trenches) of 230mm spreding thickness and consolidated (punned) upto 180mm thickness complete all as specified and as directed.

Supply & Laying Sub Class 'B' Bricks,old size, well burnt, laid breadth wise along the length of cable laid in trenches over sand cushion for UG cable protection complete all as specified and directed.

M& L for boring for 50 mm GI pipe for road crossing/cable complete all as specified and directed by Engr in Charge.

S&F sheet metal enclosure with socket plug top and MCB's SPN enclosure with 2 pin and earth plug and socket complete with one single pole MCB 20 Amps , 240 Volt complete all as specified and directed.

S&F Geyser 25 ltr capacity vertical type with BEE 5 star rating, having working pressure 8.0 Kg/cm² (max), electric water heater with ABS cover outer body 3mm EPAC (Engineered Polymer Anti Corrosion) coated inner tank to suit any kind of water, interchangeble colour panel, vitreous enamel coated incoloy heating element for long life, adjustable capilary thermostat for temparature regulation, multifunctional safety valve, hot and cold water CP flexible pipe etc and fixing along the wall complete all as specified and directed. (Make:- USHA, Model Mystry or equivalent model of V-Guard / Recold / Havells / Bajaj)

S&F in repairs Salt Glazed gully trap square or round mouthed 150x150mm, (type p or q or s) setting and and jointing with solvent cement etc complete all as specified and directed.

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement etc complete all as specified and directed.

S & F 100 mm cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B1 1:2:4 complete all as specified

Ditto all as per item No.186.00 here-in-before but nahani trap.

(Note : The Scope of Work contained in 'Sch of Credit' amounting to Rs.32286.40 (refer Tender Srl Page No 43). The Quoted sum shall be arrived at after deducting the amount of “Sch of Credit” from the total amount of the ‘BoQ’

S K ENTERPRISE

M/S LOKENATH ENTERPRISE

M/S BENGAL ENGINEERING ENTERPRISES

SREE SWAPAN KUMAR GHOSH

MUKHERJEE ENTERPRISE

M/S Banerjee construction co

M/S G D CONSTRUCTION