CONSTRUCTION OF COMBINED COURT BUILDING CONSISTING OF FIVE NUMBERS OF COURTS AND FIVE NUMBERS OF JUDICIAL OFFICERS QUARTERS AT SATHYAMANGALAM IN ERODE DISTRICT

Amount

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Upto 2.00M lift

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Cement Concrete 1:5:10 (One Cement, Five M-Sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification.

Damp proof course with Cement Mortar 1:4 (One Cement and Four M-Sand) 12mm thick mixed with best approved quality water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used, finishing and curing etc. complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling M-Sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Refilling with excavated earth other than Crushed stone Sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supplying and filling GRAVEL the sides and basement with a lead of 0 to 1km in layers of not more than 15cm thick,well rammed,watered and consolidated complying with standard specification etc complete.

Cement Concrete 1:5:10 (One cement, Five M-Sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation.

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Centering for curved surfaces of all RCC items of work

Circular Column

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

Providing and laying in position, standardised concrete Mix M-2o Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc.

For Foundation and Basement

For Superstructure in Ground Floor

For Superstructure in First Floor

For Superstructure in Second Floor

For Superstructure in Third Floor

For Superstructure in Fourth Floor

Cement Concrete 1:3:6 (One Cement, Three M-Sand and Six hard broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One Cement, Three M-Sand and Six hard broken stone jelly). Dummy columns should be at least 1 metre height)

For Superstructure in First Floor

For Superstructure in Second Floor

For Superstructure in Third Floor

Cement Concrete 1:3:6 (One Cement, Three M-Sand and Six Hard broken stone jelly) using 20mm size hard broken stone jelly excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4(One Cement, Two M-Sandand Six hard broken stone jelly) for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One Cement, Three M-Sandand Six hard broken stone jelly). Dummy columns should be at least 1 metre height)

For Foundation and Basement

Brick work in Cement Mortar 1:3 (One cement and three M-Sand) using Fly Ash Bricks of size 23x11x7 cm for foundation and basement including curing, etc., complete complying with standard specification.

For Foundation and Basement

Brick work in Cement Mortar 1:5 (One cement and Five M-Sand) using Fly Ash Bricks of size 23x11x7 cm for foundation and basement including curing, etc., complete complying with standard specification.

For Foundation and Basement

For Superstructure in Ground Floor

Brick work in Cement Mortar 1:6 (One cement and Six M-Sand) using Fly Ash Bricks of size 23x11x7 cm for foundation and basement including curing, etc., complete complying with standard specification.

For Foundation and Basement

For Superstructure in Ground Floor

For Superstructure in First Floor

For Superstructure in Second Floor

For Superstructure in Third Floor

For Superstructure in Fourth Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.

Using MS / RTS Rods

Brick partition walls of 11.00cm thickness using Fly Ash Bricks of size 23x11x7 cm in Cement Mortar 1:3 (One Cement and Three M-Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers.

For Foundation and Basement

For Superstructure in Ground floor

For Superstructure in First Floor

For Superstructure in Second Floor

For Superstructure in Third Floor

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no M-Sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

For Superstructure in Ground floor

For Superstructure in First Floor

For Superstructure in Second Floor

For Superstructure in Third Floor

For Superstructure in Fourth Floor

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 16 to 18mm of approved quality set in Cement Mortar 1:3 (One Cement and ThreeM-Sand ) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Paving the floor with best quality Vertified Tiles of size 800 x 800 x 10mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three M-Sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three M-Sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Kota stone slabs of size below 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three M-Sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with Self Designed Colour Ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M-Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three M-sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Skirting the wall with fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Jet black best quality in Cement mortar 1:2 (One cement and two M-sand)in all floors etc., complete complying with standard specifications and as directed by the departmental officers.

Labour charges for providing Double nosing to granite stone slab in all floors neatly and fixed in position so as to make it perfectly smooth and shining and to the alignment etc., complete complying with standard specification and as direct.

Dadooing walls with printed design colour glazed tiles of size 300 x 450 x 8mm set in Cement Mortar 1:2 (One Cement and Two M-Sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Supplying and fixing fine polished cuddapah slab of following thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct.

38/40mm thick

Labour charges for providing Double nosing to Cuddapah stone slab in all floors neatly and fixed in position so as to make it perfectly smooth and shining and to the alignment etc., complete complying with standard specification and as direct.

Providing granolithic floor finish of the 25mm thickness with plain cement concrete 1:2:4 (One Cement, Two M-Sand and Four hard broken stone jelly) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Plain Cement Concrete 1:2:4 (one cement, two M-Sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing.The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Supplying, fabricating and fixing in position of Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc., confirming to ISI specified ensured of right butt joint riveted hold assembly with nylon insert,not be welded with special purpose hard ware.Proclaimed including phopating as per ISI with rust preventive primer ready to assemble condition for easy installation at site including dismantling,making necessary chipping and holes in RCC columns, walls with power drills to the extent required ,including providing concrete 1:2:4 inside the box curing etc complete.The cost includes the cost of hold fast ,plastic bush, insert receiver,rubber bottom,shock absorber etc complete as directed by the departmental officers in all floors.

Supplying and fixing solid core particle board flush shutter of nominal thick of 35 mm with necessary T.W. internal lipping conforming to IS 2302 with both sides alround commercial ply 35mm thick including supplying and fixing cost of wind appliances and furniture fittings such as 1no .200x12mm aluminium tower bolt 2nos. 150x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 3 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete as directed by the departmental officers.

Single Leaf

Double Leaf

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supply & fixing of WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/-1mm) & minimum Bulk Density of 550 KG/ cub.Mt. & shore Hardness of 55. For the aesthetic appearance, the door Shall be a printed digitally on the side of the shutter and the design is as decided by the Engineer in Charge of the departmental. The WPC door shall be fixed onto the WPC frame with 3 Nos of 5" SS Hinges and the door shall have 2 towerbolt on one side and 1 towerbolt or aldrop on the other side for locking system and 2 numbers of handle on the either side of the door shutter, all made of aluminium

Supply & fixing of WPC door shutter, extruded as a single core board with rifid WPC compound with the thickness of 25mm (1- 1mm) & minium bulk density of 550 KG/Cub.& shore hardness of 55. The door shall be a plain matt board as decided by the Engineer in Charge of the department. The WPC door shall be fixed onto the Aluminium 'G' type channel with Wheel and the door shall have 2 Hooks in SS, 2 Handles 4" in SS. (Sliding door)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete..

Single Leaf

Double Leaf

Fabrication, supply and fixing in position of 'N' type ventilators using M.S. angle of size 25 x 25 x5 mm for frame and M.S. Flat of size 20 x 3 mm for fixing the weld mesh and using 25 x 22 x3 mm 'T' section for frame glass. Special type of Hold fast welded to the frame of 45 degree inclined towards centre for wall and fxing the weldmesh 25mm square including cost of 3mm thick pinheaded glass panes for all panels and fixing the glass panels with necessary clips & putties with required bolts, nuts and washers and one coat of red oxide primer etc. including necessary dismantling, making holes in RCC columns, beams, masonry wherever necessary with power drill to the extend required and made good to the original conditions after fising as directed by the departmental officers.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing M.S. Grill of approved design for open courtyard, grill, grill works to doors and window opeings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification and as directed by departmental Officer

Manufacturing, supplying and fixing of cupboard shutter using country wood (kongu) frame of 100 m x 32 mm thick for outer frame horizontal and vertical memebers. The shutter frame of size 75 x 32 mm of country wood scantling (Horizontal 3 nos., Vertical 2 nos., of reach shutter) with 12 mm thick both side prelaminated particle board (exterior grade) shutter.The shutter are fixed to the frame with requied 6 nos., o alumium hings 100 x 30 mm 2 nos., 'D' type alumium hadle 100 mm 2 nos., of aluminum tower bolts 75 x 10 mm 2 nos., of cupboard lock etc., the country wood frame shall be painted two coats with synthetic enamel paint over one coat of wood primer. The prelaminated particle board and furniture fittings used should be got approved by the Executive Engineer before use on works. The cost is inclusive of alumnum handle. tower bolts, piano type hingers, screws, nails, and required further fittings and painting the frame and inner side of prelaminate shutter etc., complete complying with standard specification.

Plastering with Cement Mortar 1:5 (One cement and Five P-sand), 12mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three P-Sand) 10mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48hours. It shall then be sand papered(waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying ist coat of putty mixed with water on the entire surface including filling up the undualations and applying 2nd coat of putty after 6hours of 1st coat of putty and then sand papering(water proof abrasive sheet) the same after it is dry and finishing the surface smoothly etc, complete complying with standard specfiications and as directed by the departmental officers.(The rate are inclusive of hire charges for grinding machine with wheel, cost of sand paper(water proof abrasive sheet), cost of putty blade, labour chargees for grinding the joints and sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc, complete) The putty should be got approved by the Executive Engineer before use on work)

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The wall putty shall be got approved by the Executive Engineer before use of work). Wall area

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three P-sand), 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement and with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:4 (One Cement and Four Plastering Sand) 20mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two M-Sand and four hard broken stone jelly), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed

50mm thick

75mm thick

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.110mm dia

Two Floor

Three Floor

Four Floor

Five Floor

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with M-Sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two M-Sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete . (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers.

Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing position CI Nahani Trap / Floor Trap of the 100 x 75mm sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of M-Sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

110mm dia PVC Pipe

75mm dia PVC Pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

110mm dia PVC Plain Elbow

110mm dia PVC Door Elbow

110mm dia PVC Y with single Door

110mm dia PVC Door Tee

75mm dia PVC Plain Elbow

75mm dia PVC Door Elbow

75mm dia PVC Y Door

75mm dia PVC Door Tee

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The PVC cowl should be got approved by the Executive Engineer before use on works).

110mm dia PVC Cowl

75mm dia PVC Cowl

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. External - UPVC Pipe - Commercial - Below Ground level

32mm dia UPVC Pipe

25mm dia UPVC Pipe

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. External - UPVC Pipe - Residential - Below Ground level

32mm dia UPVC Pipe

25mm dia UPVC Pipe

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. External - UPVC Pipe - Commercial - Above Ground level

40mm dia UPVC Pipe

32mm dia UPVC Pipe

25mm dia UPVC Pipe

20mm dia UPVC Pipe

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. External - UPVC Pipe - Residential - Above Ground level

40mm dia UPVC Pipe

32mm dia UPVC Pipe

25mm dia UPVC Pipe

20mm dia UPVC Pipe

Supplying UPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements Since the labour for cutting, threading / pasting, sundries have already been included under pipe line item of works, no separate provision for fixing UPVC specials needs to be allowed

20mm dia UPVC Union

25mm dia UPVC Union

32mm dia UPVC Union

40mm dia UPVC Union

20mm dia UPVC Elbow

25mm dia UPVC Elbow

32mm dia UPVC Elbow

40mm dia UPVC Elbow

20mm dia UPVC Tee

25mm dia UPVC Tee

32mm dia UPVC Tee

40mm dia UPVC Tee

20mm dia UPVC Coupling

25mm dia UPVC Coupling

32mm dia UPVC Coupling

40mm dia UPVC Coupling

20x15mm dia UPVC Reducer

25x20mm dia UPVC Reducer

32x25mm dia UPVC Reducer

40x32mm dia UPVC Reducer

20x15mm dia UPVC Reducer Elbow

25x20mm dia UPVC Reducer Elbow

32x25mm dia UPVC Reducer Elbow

40x32mm dia UPVC Reducer Elbow

20x15mm dia UPVC Reducer Tee

25x20mm dia UPVC Reducer Tee

32x25mm dia UPVC Reducer Tee

40x32mm dia UPVC Reducer Tee

20mm dia UPVC Hex Nipple

25mm dia UPVC Hex Nipple

32mm dia UPVC Hex Nipple

40mm dia UPVC Hex Nipple

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

40mm dia Gate value

32mm dia Gate value

25mm dia Gate value

20mm dia Gate value

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing of Granite Sink of size 600 x 600 x 250mm etc, complete complying with standard specificaion and as directed by the departmental officers

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Supplying and filling 40mm guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc. complete complying with standard specification.

Supplying and filling 20mm guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc. complete complying with standard specification.

Supplying, laying and jointing glazed stone ware pipes of the 100 dia (Cement joint) of approved quality with spigot and socket ends and fixing them in dry condition using spun yarn and cement including petty masonry shoring and strutting wherever found necessary and laying the pipe line in the alignment at the specified gradient and testing with necessary tools and plants, etc., and re-filling the trench with excavated earth and levelling the ground etc., complete complying with standard specifications. (Earth work excavation, re-filling with excavated earth will be measured and paid separately).

Supplying, laying and jointing glazed stoneware pipes of 100 dia of approved best quality with spigot and socket ends (in reverse direction) in dry condition and laid in loose joints (i.e.) without cement and spun yarn, so that the waste water can be drained to the trenches already available, excluding cost of earth work excavation, cost of re-filling with M-Sand/ earth, but including laying the pipe in true alignment and gradient and conducting required water supply test for draining with necessary tools and plants, etc., complete complying with standard specifications.

Supplying and fixing in position 150mm dia stoneware tee of approved best quality and provding leak proof joints with cement, spun yarn, etc., including dismantling the brick work and re-doing the dismantled portion to the original condition, etc., complete complying with standard specifications (The stoneware tee shall be got approved by the Executive Engineer before use on work)

Vertical bore well 1-150

Vertical bore well 151-180

Vertical bore well 181-210

Vertical bore well 211-240

Vertical bore well 241-270

Supplying suitable size casing pipe for 6" dia borewell ( 6 kg/sqcm) of best quality with ISI mark with necessary PVC coupling with socket end, The PVC should got approved by the departmental officers before execution.

Supplying and erecting and Commissioning of best approved quality of 7.50 HP submergible with heavy duty double cylinder air lifting compressor with standard pully guard with 7.5 HP motor 1440 RPM 440V,50Hz,220V three phase TEFC heavy duty motor arrangement and tying the hoses together with copper wire and providing necessary nipples at joints and giving connections to the motor, delivery line transportation charges etc., complete

Supplying and erecting and Commissioning of best approved quality of 5 HP submergible motor with heavy duty double cylinder air lifting compressor with standard pully guard with 5.0 HP motor 1440 RPM 440V,50Hz,220V three phase TEFC heavy duty motor arrangement and tying the hoses together with copper wire and providing necessary nipples at joints and giving connections to the motor, delivery line transportation charges etc., complete

Supplying and fixing the 40 mm dia UPVC Pipe for borewell etc, complete complying with standard specification and as directed by the departmental officers

upply and fixing of water proof 3 core 4 sq.m flat P.V.C insulated copper cable for submersible pumpset in the borewell including fixing and fying with copper wire and clamping waterpipe etc., complete as directed by the departmental officers.

Supplying and fixing wall mounting of 3 Phase Panel board with following accessories a.Suitable DOL type push botton automatic starter etc., complete.

Supplying and fixing Nylon rope for borewell etc., complete.

Providing Anti-Termite Treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 part I to IV in stages to suit the progress of work consist as per the detailed specification as below (Measurements taken for the plinth area for the purpose of payment) including braking of termit mounds, making holes with crow ar, closing the holes after the treatement and including cost of chemicals, labour charges transport and storing etc., complete (The chemical should be got approved by the Executive Engineer before use on works) Stage-1: Spraying anti-termite chemical solution for the foundation before laying concrete in bottom and sides of foundation. Stage-2: Spraying anti-termite chemical solution to the grade beam level, spraying has to done for the grade beam, brick masonry contact with the back fill earth. Stage-3: Spraying anti-termite chemical solution on the sand for the flooring before laying the flooring concrete. This treatment has to be carried out on the sand filling by making holes with crow bar to a depth of 60 cms and at 60cms intervals on both. Stage-4: Spraying anti-termite chemical solution alround building outside by making holes through bar before laying plinth protection and the holes to be closed after the treatment.

Supplying, fabricating, erecting and fixing False ceiling using perforated sheets (10mm thick) upto a ceiling height of 4.5m from floor level etc, complete complying with standard specification and as directed by the departmental officers

Providing Cornice Work for Gyp Board False Ceiling etc, complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position Sanitary Napkin incinerator Machine (REPROCIDE SND - SLIM) [capacity: 25 to 30 napkins at a time] with 3 meter flexi GI piping with accessories inlcuding conveyance, loading, unloading with standard specification etc., and The make and quality got approved by the departmental office before use on works and as per standard specification.

Supplying and erecting in position of 250Litrecapacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World HealthOrganisation (WHO) Standards (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No. Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact etc, complete complying with standard specification.

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS 15683 with pressure gauge, discharge hose & control nozzie, wall mounting bracket, safety clip etc., ncluding conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT/ SAFETY FIRST ? EQUIVALENT.

Supplying and Fixing of Aluminium Dye Cast Letters of approved size and colour. The colour treatment process is achieved with MRF colour coat and then the processed coloured layer is set into the kiln for the heat treatment process for the following sizes etc, complete

Aluminium Dye cast letter 9"

Supplying and fixing the Tamil Emblem 15" etc, complete complying with standard specification and as directed by the departmental officers

Providing Polymer Coating (Water Proof Coating) for sunken Portion of toilet with following specification and the surface shall be cleaned to remove all dust, foreign, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred throughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Supplying and fixing in position of best quality and approved variety of PVC WATER TANKS of following litres capacity conforming to I.S.I specifications with necessary inlets and the outlets and overflow, cleaning pipe arrangements and labour charge for fixing in position etc., and properly fixed in the floor top as directed by the departmental officers.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring with 3 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End.

Supply and fixing of 1No.6A two module 5pin socket, 1no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections.Higher End

Supply and fixing of 15W LED Bulb and Battern Holder for BH point .

Supply and fixing of 4'20W LED Tube light fitting with Batten (Make : Higher End) with TW round blocks on wall or ceiling with LED tube with PVC unsheathed Copper leads from terminals to the fitting.

supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb. (For Lift well )

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia GI pipe (class B) with 1no. 32mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting.(For External)

Supply and fixing of 2'20W LED Mirror light fitting with Batten (Make : Philips /wipro) with PVC unsheathed Copper leads from terminals to the fitting. (For Judge Qtrs Bath)

Supply and fixing of 1200mm (48") Sweep BLDC ceiling fan complete (HIGHER END) with 2 Module 100 W Fan Step Regulator (HIGHER END) with stepped with 1 meter down rod on the existing fan clamp

Supply and fixing of 300mm (12")sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan.

Supply & Fixing of AC / DC 76mm Buzzer /call bell suitable for 230 Volts 50 c/s single phase AC supply on suitable TW Board with push switch.

Supply and fixing of 3Nos. 6A two module 5pin socket, 3nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End. ( Computer plug)

Supply and fixing of 1No. 6/16A two module socket, 1no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End (Power plug)

Supply and Fixing of 16A Two-way switch in suitable MS box on wall with earth connection.(HIGHER END) (For 4 Nos. Lift)

Supply and fixing of 20Amps DP plug and socket in sheet steel enclosure with 32A DP MCB in flush with wall with earth connection.[For AC Plug]

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 7Segment 4way TPN MCB Sheet Steel Distribution Board with metal/acrylic door cover flush type / surface type fitted with busbars and neutral links with single or three phase MCB outgoings and seperate 4way provision for accomodating 1No 4Pole incoming MCB/Isolator and another seperate 4Way provision for accodating 1No. 4Pole ELCB/RCD (Totally 8ways in one segment)(3x4 ways in each segment )and seperate provison for MCB/Isolators (Totally 12 Nos) for sub incomers in 3 segments with label holder an provison for taking of cable for size not less than 35 sq.mm with the following in flush with wall earth connection only. 1) 63A 4P MCB - 1No 2) 63A 4P 30MA RCCB/ELCB-1No 3) 63A DP MCB Isolator - 3Nos 4) 6A to 32A SP MCB - 12Nos (HIGHER END)

Supply and fixing of 7Segment 6way TPN MCB Sheet Steel Distribution Board with metal/acrylic door cover flush type / surface type fitted with busbars and neutral links with single or three phase MCB outgoings and seperate 4way provision for accomodating 1No 4Pole incoming MCB/Isolator and another seperate 4Way provision for accodating 1No. 4Pole ELCB/RCD (Totally 8ways in one segment)(3x4 ways in each segment )and seperate provison for MCB/Isolators (Totally 12 Nos) for sub incomers in 3 segments with label holder an provison for taking of cable for size not less than 35 sq.mm with the following in flush with wall earth connection only. 1) 63A 4P MCB - 1No 2) 63A 4P 30MA RCCB/ELCB-1No 3) 63A DP MCB Isolator - 3Nos 4) 6A to 32A SP MCB - 18Nos (HIGHER END)

Supply and fixing of vertical type 4 way triple pole neutral MCCB DB in sheet steel enclosure double break metal cover with IP 42 protection with 1No. 125A MCCB MCB as incoming 4Nos. 63A TP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCCB,MCCB DB and MCB's should be with the ISI mark (HIGHER END)

Supply and fixing of vertical type 8 way triple pole neutral MCCB DB in sheet steel enclosure double break metal cover with IP 42 protection with 1No. 125A MCCB Switch as incoming 8Nos. 32A TP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCCB,MCCB DB and MCB's should be with the ISI mark (HIGHER END) (DATA-7) ( Court Hall-1-5, AC Units)

Supply and run of 2 of 1.5 sqmm PVC insulated SC unsheathed FRLS Conductor of 1100V grade in suitable PVC rigid pipe concealed in all and ceiling with continuous earth wire connection of 1.5sq.mm coppe rwire and making good of the concealed portion with suitable colour. (for call bell & 6 A plugs) ( For Call Bell)

Supply and run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion. (For 3X6A Computer Plugs)

Supply and run of 2 of 4 sq.mm .PVC in sulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in all and ceiling with continuous earth wire connection of 4sq.mm coppe rwire and making good of the concealed portion with suitable colour.[For 20A MC Plug,Socket 16A Power Plug and Set Plugs]

Supply and run of 2 of 6 sq.mm .PVC in sulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in all and ceiling with continuous earth wire connection of 4sq.mm coppe rwire and making good of the concealed portion with suitable colour.[For 8W SPNMCB DB and 12W SPNMCB DB]

Supply and run of 4 of 6sq.mm.PVC insulated SC unsheathed FRLS copper conductor of 1100Vgrade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4sq.mm copper wire and making good of the concealed portion with suitable colour. (For 32A 4P MCB Switch in Court Hall AC Units)

Supply and Run of 4 of 16 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable 40 mm PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 16 sq.mm. PVC insulated SC unsheathed FRLS copper wire with painting of suitable colour.(For 4 Ways 7 segment DB)

Supply and run of 4 of 25 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 16 sq.mm. PVC insulated SC unsheathed FRLS copper wire with painting of suitable colour. (For 4W & 8W TPNMCBDB Veritical)

Supply and fixing of 32 A FP MCB in 4 pole sheet steel enclosure in flush with wall and earth connection. (Higher end). (For Court Hall AC Units)

Supply and fixing of 32A TPNMC switch on suitable angle iron frame work with MS cable entry box with earth connection only.(For Pump Set )

Supply and fixing of 63A TPNMC switch on suitable angle iron frame work with MS cable entry box with earth connection only. (For Lift Main)

Supply and Fixing of Metal one way FP Enclosure with 63A FP RCBO 30 mA on wall with earth connection.(Higher End) (In Lift Machine Room)

Supply erection testing commissioning of 2.00TR (6000 KCal/Hr) ABS Plastic split type Air Conditioner confirming to IS1391[Part 2] 1992 with Rotary compressor operating on refrigerant R-22/Non CFL suitable for wall mounting for operating on 230V 50HZ single phase AC supply with Three star rating Model as per BEE Specification and capable of performing the following functions. A) Cooling, B) dehumidifying C) Air circulating D) Filtering the installation work for the above split type AC units includes the following. 1. Mounting /fitting indoor and outdoor units at their respective locations. 2. Laying refrigerant pipe line of 6mtrs distance and connecting the both units after drilling hole in the wall if required thickness of the copper tubing shall not be less than 0.80mm 3. Insulating the suction pipe with expanded polythene foam 5mm thick tubing. 4. Laying 15mm dia flexible PVC drain pipe of 6mtrs length to throw out the condensate water being formed in the indoor unit. 5. Leak testing the entire gas unit. 6. Charging refrigerant gas in the unit. 7. suitable electric wiring to be provided with 2.5sq.mm PVC insulated copper wire between indoor and outdoor units up to 4mtrs length and up to switch within 3mtrs of location of indoor unit.(Make -Carrier/voltas /Blue star make only)

Supply and fixing of 5KVA Automatic voltage stabilizer of wall mounting type with Automatic time delay switching arrangements suitable to operate on 230V Single phase supply.

Supply and laying of 5/8'' and 3/8'' copper pipe (Extra beyond 3Mtrs supplied with AC Unit)

Supply and fixing of MS Stand for fixing outdoor unit.

Supply and fixing of water drain line (1'' PVC Pipe) (For Split AC Unit)

Supply and run of 3 of 2.5 sqmm (36/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable heavy gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 2.5sqmm PVC copper wire wire with painting of suitable colour. ( Lift 2 Way)

Supply and clamping of 3½ x 25 sq. mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps. ( For Lift)

Supply and fixing of brass cable gland for 3½ 25 sq mm PVC armoured LTUG cable, with earth connection.

Supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia.GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour.

Supply and laying of 4 x 10 sq. mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75metre putting 0.15mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. [SD-180] (For External Street Light and Pump Motor Control)

Supply and clamping of 4 x 10 sq. mm PVC LTUG armoured LTUG cable on post or on wall with MS (Clamps.

Supply and fixing of brass cable gland for 2 x 16 sq mm PVC armoured LTUG cable, with earth connection.

Supply and laying of 4 x 16 sq. mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75metre putting 0.15mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (For Pump Set)

Supply and clamping of 4 x 16 sq. mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 4 x 25 sq mm PVC armoured LTUG cable, with earth connection.

Design, Engineering, Supply, Fabrication, Erection, Testing, Commissioning and Handing over of 1No.13 persons 884kgs. Capacity Passenger Lift as per the following specifications including Taxes and Duties. 1. Location : Court Building at Sathy 2. No. of Lift : One No 3. Type of Lift : Passenger Lift machine room - Gearless model 4. Capacity of Lift : 13 Persons / 884kgs 5. Speed : 1.5 mtr / sec 6. Type of Drive : V3F Drive with enhanced ride comfort and near Zero Level Functions. 7. No. of Floors :Three (Stilt+GF+FF) 8. Total Travel : 12Mtr / Pit 1600mm / Head room 4250mm 9. Leveling accuracy : High level accuracy with smooth and jerk free stopping. 10 Construction of : 18 SWG High Quality Car. S.S. Car and Hand rail, PVC flooring and Perspex False Ceiling. 11 Position of Machinery : Directly above the Lift well – Gearless with machine room. 12 No. of Landings : Three (Ground +2) in the front side. 13 No. of Car Entrance : One in the front side. 14 Car Entrance : Power operated V3F Drive, Centre opening Sliding Stainless Steel (1.5mm) Hairline finish door.

31 Servicing and maintenance : Free Comprehensive Maintenance for one Year Guarantee period. 32 Automatic Rescue Device : Provision to facilitate the landing to the nearest floor at the time of power failure. The ARD consists of suitable Battery system with charger, Inverter, under voltage protection system etc. complete with all accessories. 33 Provision for Intercom : To be provided in the Ground Floor & Machine Room with Phone (Press & Speak). 34 Lift License : Preparation of Drawings, payment of inspection charges to CEIG and insurance policy and Obtaining CEIG approval for the Lift as per Lift act should be done by the Lift contractor. 35 Floor Position : Included with LED display and floor annunciator.36 Special Features: a. Infra red door sensor with full height screen b. Full width half height rear panel mirror c. S.S. hair finish hand rail in car d. Stainless steel signal features e. Vandal proof SS button with SS cover f. S.S. hair finish door frames for landing doors g. V3F door operator h. Call register signal i. Stainless steel facio plates for car operating panel and landing fixtures j. Steel ladder for Lift machine room k. On / Off switch for fan and light l. Over-load warning indicator with audio Announcer

m. Voltage stabilizer for control circuit. 37 Over Speed Governor, Phase failure and Phase reversal Relay, alarm bell, T guide brackets for car and counterweight, Rubber padding under the winding unit, Motor of adequate capacity, signal reduction worm gear Electromagnetic brake with compression springs, Car safety gears, Buffers, Electro mechanical locks, Emergency key, side supporting angles, Motor over - load protection devices, Final limit switch main, suspension ropes, Counter weights, Lifting joist for mounting the Machineries. ,. 38.Guarantee : Guarantee at least for one year for the materials and workmanship of equipments should be offered by the Lift contractor. 39. Site testing in accordance with IS 14665 should be carried out at the time of Handing over to the User department.40. Supply, operation and maintenance manual and necessary tools for operation and a set of spare parts required for one year to be provided.(In Court Building-4Nos(As per SR Rate)(Johnson / Kone / OTIS) 25 Emergency provisions : Battery operated Alarm bell & Light to be Provided with Automatic charging device. 26 Fire Man’s switch : In the Ground Floor 27 Minor Builder works : included 28 Scaffoldings : included

Design, Engineering, Supply, Fabrication, Erection, Testing, Commissioning and Handing over of 1No.13 persons 884kgs. Capacity Passenger Lift as per the following specifications including Taxes and Duties. 1. Location : Quaters Building at Sathy 2. No. of Lift : One No 3. Type of Lift : Passenger Lift machine room - Gearless model 4. Capacity of Lift : 13 Persons / 884kgs 5. Speed : 1.0 mtr / sec 6. Type of Drive : V3F Drive with enhanced ride comfort and near Zero Level Functions. 7. No. of Floors : Four (Stilt +GF+F.F+SF)8. Total Travel : 16Mtr / Pit 1600mm / Head room 4250mm 9. Leveling accuracy : High level accuracy with smooth and jerk free stopping. 10 Construction of : 18 SWG High Quality Car. S.S. Car and Hand rail, PVC flooring and Perspex False Ceiling. 11 Position of Machinery : Directly above the Lift well – Gearless with machine room. 12 No. of Landings : Four (Ground +4) in the front side. 13 No. of Car Entrance : One in the front side. 14 Car Entrance : Power operated V3F Drive, Centre opening Sliding Stainless Steel (1.5mm) Hairline finish door.

Inverter, under voltage protection system etc. complete with all accessories. 33 Provision for Intercom : To be provided in the Ground Floor & Machine Room with Phone (Press & Speak). 34 Lift License : Preparation of Drawings, payment of inspection charges to CEIG and insurance policy and Obtaining CEIG approval for the Lift as per Lift act should be done by the Lift contractor. 35 Floor Position : Included with LED display and floor annunciator. 36 Special Features: a. Infra red door sensor with full height screen b. Full width half height rear panel mirror c. S.S. hair finish hand rail in car d. Stainless steel signal features e. Vandal proof SS button with SS cover f. S.S. hair finish door frames for landing doors g. V3F door operator h. Call register signal i. Stainless steel facio plates for car operating panel and landing fixtures j. Steel ladder for Lift machine room k. On / Off switch for fan and light l. Over-load warning indicator with audio Announcer

m. Voltage stabilizer for control circuit. 37 Over Speed Governor, Phase failure and Phase reversal Relay, alarm bell, T guide brackets for car and counterweight, Rubber padding under the winding unit, Motor of adequate capacity, signal reduction worm gear Electromagnetic brake with compression springs, Car safety gears, Buffers, Electro mechanical locks, Emergency key, side supporting angles, Motor over - load protection devices, Final limit switch main, suspension ropes, Counter weights, Lifting joist for mounting the Machineries. ,. 38.Guarantee : Guarantee at least for one year for the materials and workmanship of equipments should be offered by the Lift contractor. 39. Site testing in accordance with IS 14665 should be carried out at the time of Handing over to the User department. 40. Supply, operation and maintenance manual and necessary tools for operation and a set of spare parts required for one year to be provided.(In Quarters Building) (As per SR Rate) (Johnson/Kone/OTIS)

Supply,testing, commissioning and handing over of 1No, 125KVA Diesel generator set of 0.8PF, 3phase, 415/ 420Volts, 50Hz, 1500 RPM complete as Per CPCB IV + Norms and BIS specifications in all respects as detailed below A) ENGINE :Water cooled diesel engine suitable for generator application with a shaft out put of 155BHP suitable at 1500 RPM under NTP conditions . The engine shall comprise the following standard scope of supply: (Make : Ashok Leyland / Equivalent) 1) Dry type Air cleaner 2) Expansion bellow 3) Radiator, radiator fan and mounting 4) Air to air charge cooler 5) Exhaust gas turbo charger 6) Lube oil cooler and lube oil filter 7) Fuel filter (pre and micro) 8) In-line mono-block fuel injection pump with governor and fuel feed pump 9) Electronic governor 10) 12V / 24V battery charging alternator 11) 12V / 24V Volt electric starter motor 12) Engine test certificate 13) Residential Mufler 14) Fly wheel with starter ring.Engine instrument panel/mounting: Engine control panel consisting of ON/OFF/START/KEY, lube oil pressure gauge, oil temperature gauge, high water temperature gauge and electronic hour meter and RPM indicator. Safety system of Engine: The engines shall trip for the following conditions with Visual alarm device. 1) Low lubricating oil pressure 2) High water temperature 3) Vee - belt failure and over speed 4) Low battery indication. The Engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load.

28) Rectangular copper bus bars (1No for each phase, neutral and earthing terminal) of adequate capacity duly colour coded with head shrinkable PVC sleeves. 29) 1No mains voltage monitor 30) Hooter/Audio alarm for indication set fails to start and for DG O/L 31) 1set timers 32) Audio and visual indication arrangements for a) Low lubricating oil pressure b) High water temperature c) Over speed 33) 1No Earth fault relay 34) Isolator to Isolate the neutral Note:1. The control panel should be complete with necessary fuses, cables, labels, other accessories with neutral isolation arrangements.2. The engine should trip for the following conditions. a) Low lubricating oil pressureb) High water temperature c) Over speed 3.Supply and fitment of Auto mains failure panel 1EB service with 63Amps switch and contactors SUF control relays timers etc. C)After Treatment System-The After treatment system should include SCR,DEF lines,DEF supply & DEF Tank. D) ACOUSTIC ENCLOSURE : Acoustic enclosure shall be powder coated and fabricated of 16SWG CRCA MS sheet.The silent canopy shall be nut bolt type construction. Critical processes of punching are done on CNC machine to maintain dimensional accuracy of hole within 0.1mm power coating done after seven-tank surface preparation process of sheet metal. Canopy panel and door shall have inside lining of FIRE-RETARDANT 64kg/m density mineral wool of 100mm thickness as acoustic material. Four hinged doors shall be provided to canopy.

The maximum permissble sound pressue level should be as per the norms prescribed by the Central Pollution Control Board / State Pollution Control Board/ Competent Authority concerened or shouble be 75 db(A) at 1 meter from the enclosure surface whichever is advantageous to the department.The emergency stop should be available on the enclosure panel.The enclosure provided shall be duly approved by the Engine Manufacturer of the Engine provided for Diesel Generator Sets mounted inside and should be to the satisfaction of inspection / testing authority concerned. SURFACE TREATMENT – PAINTING : The enclosure shall be suitably treated for degreasing, de-rusting and phospating. The canopies are passed through seven-tank treatment thoroughly. ADDITIONAL FEATURES OF CANOPIES : Canopy fabricated on CNC machines with dimensional accuracy of 0.1mm so as to increase its durability. Special designed supporting rips/structures are used in canopies so as to give sturdiness and to reduce the vibrations of the DG sets if any. WORLD CLASS COOLING PACKAGE: Canopies shall have cooling package for which it can perform at 45 deg c/ambient temperature. No grounding required on the ground, only a level surface capable of with standing the DG weight. Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set

. The Gen set frame shall also be provided with hooks for unloading. Temperature rise inside the canopy: Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well with in 5-7 deg centigrade. D) Base Frame Base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled, with cross members mounted on AVM. The base frame shall have provision for mounting of acoustic enclosure on it. The supply of Gen set includes loading, unloading and transportation charges. E) Fuel Tank 200Ltrs. Removable Fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet an outlet connections and mechanical fuel gauge. Fuel tank can be easily removed for cleaning or any maintenance.. F) Battery 2Nos 12V 180 AH battery Supply of lubricating oil to run the genset for minimum of 8 hours by supply of 150 litre dieselSupply of tools like such as 15" cutting plier- 1No,Serew driver 9"X6" - 2Nos, DE spaners ( 6 Nos) - 1set,Adjustable spanner - 1No,1/2 Ip Hammer - 1 No,spanner for removing engine oil plug-1No,Line tester - 1 No and line tester for the maintenance and operation of generator set-1set. (Kirloskar/Ashok Leyland)

Supply and installation of exhaust piping of sufficient length with suitable MS pipe so as to extend outside the generator with necessary thermal insulation.

Erection of Gen set: Providing suitable concrete foundation with cement concrete 1:2:4 with sand cushion all around the foundation for erection of 125 KVA Diesel Generator set over the existing fountation and erection of generator set with proper alignment over the existing fountation to suit 125KVA Genset fountation size L4200XW1600XH2000mm.

Supply and demonstration of the following safety accessories. a) 1 meter x 1 meter x1/2 inch 11kv rubber mat - 5Nos. b) one set of 4 nos. 9 liters fire buckets with metal stand frame - 1set c) first aid box with medicine - 1no d) 11 kV rubber hand gloves - 2 nos. e) 2 Kg capacity dry powder type fire extinguishers -1No f) Hand operated pump to transfer fuel from standard barrel to fuel tank-1No g) First aid chart in Tamil and English -1No h) Battery water acidity tester -1No i) Earth discharge rod -1No j) Danger board-1No k) Emergency Lamp with PL lamp -1No

Preparation of site plan,physical layout, electrical line schematic diagram in 10 sets getting drawing approval from CEIG preparation of completion report, rectification report and arranging CEIG inspection and obtaining safety certificate preparation of 1 set of approved drawing and a copy of safety certificate in a neat frame work to be fixed in generator room and payment of CEIG inspection fees.

Supply & Erection of Dust Vermin proof EB metering cubicle panel made out of 16SWG CRCA sheet steel enclosure with supply and fixing of the following interior mounting in two Vertical rows with a central bus bar chamber with interconnections. 1) Metering chamber for fixing EB meters on hylum sheet of 6mm thickness with necessary bolts & nuts so that the EB meters can be fixed firmly on it with view glass arrangements-7Nos 2)100A porcelain fuse units (500V) - 3Nos 3) 63A porcelain fuse units (500V)-9Nos 4) 32A porcelain fuse units (240V)-3Nos 5)63A FP RCBO-4Nos 6)32 DP RCBO -3Nos The bus bar chamber shall consist of 4Nos 25mm x 6mm (1"x¼ “) copper flats for 3phases and neutral. The No 1"x1/8" copper flat for earth bus provided all around the panel. The inter connection between buses to meter, meter to fuse unit 16Sq.mm Cu. PVC insulated copper wire. The buses mounted on the SMC bus insulator at proper & sufficient spacing between the buses as per IE rules .The bus bar chamber should be segregated from the adjacent chamber by providing hylum sheet of 6mm thick as portion. Phase & neutral copper buses should be provided with heat shrinkable sleeves using RYB & Black colours.

The panel shall have one coat of red -oxide primer paint & two coats of synthetic enamel paint of approved colours, approved by the department officers and also danger board. The panel shall be mounted on 3” x 1 ½” x 5” MS base channel provided all around the bottom of the panel. The whole arrangements shall be erected on a masonry pedestal to be constructed with suitable foundation with bolt and nuts, such that the lowest SDF unit fuse handle is at a height of 0.75m from the ground level [For JM Judge Quarters -1,2,3 Service meter panel board]

Supply and erection dust & Vermin proof wall mounting type energy meter cubical made up of 165WG CRCA sheet steel with bus chamber, metering chamber & fuse chamber with necessary stiffnesswith suitable metering. The bus chamber should be fixed with 50X6 mm (2X1/4") tinned copper flats for 3 phase & neutral on suitable epoxy mounts for termination of incoming cable and for outgoing flexible copper leads to meter. The meter chamber should be provided with 6mm thick hylum sheet for fixing meter. The fuse chamber should be provided with CT for 3 phase voltmeter, Ammeter and 3 Nos. 500A porcelain fuse units expended with bus bar & 25 X 6mm Cu. neutral bus for terminating outgoing cables. All the doors should be provided with lockable & Sealing arrangements and 2 Nos. 25 X 3 mm copper flats should be provided at the rear for earthing.All the door should be earthed with suitable flexible leads.The cubical should are powder coated with grey colour and supported on suitable MS angle base frame work. (For LTCT Panel Board)

Supply and fixing of 3 Phase 400A aerial fuse unit for 3Nos 315 A fuse units (500V) on suitable MS sheet covered with 6mm thick hylem sheet on suitable angle iron work the tapping pole with necessary clamps.

The bus bar chamber should have 3 Nos of 1 1/4" x 1/4" tinned copper flat for 3 phases and 1 No 1" x 1/4" tinned Cu.flat for Neutral and body earth bus must be run all round the panel using 2 runs of 1" x 1/8" tinned copper flat to provide earth connection to the cubicle switches cable glands etc., the bus bars should be supported on synthetic enamel compound at equal interval as per IS specification.The incoming and outgoing switches should be connected to the bus with the following copper flats.1) 400A FP switch with 2" x 1/4" copper flat 1) 250A FP switch with 1.2" x 1/4" copper flat 2) 63A TPN switch with No.8 SWG copper wire The switches should be separated from the bus bars by 6 mm thick hylum sheet and all switches should be properly earthed by solid copper flat as per IE rules and CEIG specification. Providing Rubber Beading for All Doors

The bus bar chamber should have 3 Nos of 1 1/4" x 1/4" tinned copper flat for 3 phases and 1 No 1" x 1/4" tinned Cu.flat for Neutral and body earth bus must be run all round the panel using 2 runs of 1" x 1/8" tinned copper flat to provide earth connection to the cubicle switches cable glands etc., the bus bars should be supported on synthetic enamel compound at equal interval as per IS specification. The incoming and outgoing switches should be connected to the bus with the following copper flats.1) 250A FP switch with 1 1/4" x 1/4" tinned copper flat 2) 125A TPN switch with 1 " x 1/8" tinned copper flat 3) 63A TPN switch with No.8 SWG copper wire The switches should be separated from the bus bars by 6 mm thick hylum sheet and all switches should be properly earthed by solid copper flat as per IE rules and CEIG specification. Providing Rubber Beading for All Doors

Supply and Laying of 3 ½ x 240 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.(SD-667) (From LTCT Meter to 250A Panel)

Supply and clamping of 3½ x 240 sq.mm PVC LTUG armoured LTUG cable armoured Pipe on post or on wall with MS Clamps.(SD-208)(From EB Post to LTCT meter & LTCT Meter to 250A Panel)

Supply and fixing of brass cable gland for 3½ x 240 sq.mm PVC armoured LTUG cable, with earth connection.

Supply and providing cable end termination of 3½ x 240 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete

Supply and Laying of 3½ x 150 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good (From Gen Supply)

Supply and fixing of brass cable gland for 3½ x 150 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3 ½ x 150 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and clamping of 3½x 185 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps. (For 250A Sub Panel Board)

Supply and fixing of brass cable gland for 3½x185sq.mm LTUG armoured cable with earth connection .

Supply and providing cable end termination of 3 1/2 x 185 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32Afuse unit (500V) 32A neutral link and earth link (1"x1/8"copperflat) on TW plank of size 375mmx300mmx19mm with supporting TW reepers of 1"thick aneither side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with1No40Amp30MA Double Pole RCD / RCCB (Higher End) with suitable necessary connection.

Supply and fixng of TNEB meter board suitable for 3phase 63A service connection made up of suitable angle iron frame work of size2feetx1-1/2 feet using angle iron of size1-1/2"x1-1/2"x1/4"rigidly fixed on wall covered with hylem sheet of size2feet x1/2feet of 6mm thickness with necessary bolt sand nuts supports and supply and fixing of 3Nos.63Afuse units (500V), 1No.neutrallink,copper earth flat of size1"x1/4"withinter connection of EB meter to fuse units by16Sq.mm PVC insulated copper wire with1 No 63Amp 30MAFourPoleRCD /RCCB (HigherEnd) withsuitable necessary connection with earth connection complete .

Supply and fixing of 3 phase 63A aerial fuse unit for 3Nos. 63A fuse units (500V) on suitable MS sheet covered with 6mm thick hylum sheet on suitable angle iron frame work the tapping pole with necessary clamps.

Supply and fixing of 32A aerial fuse unit (500V) on suitable 100X100MM TW Concealed box with 6mm thick hylum sheet on the tapping pole with necessary clamps.

Supply and run of 2 of 6 sq.mm (84/0.3) PVC SC unsheathed FRLS copper conductor of 1100V on 7/20 GI bearer wire for service connection mains. (For Dist Judge , Sub judge Quarters- camp office EB service Main)

Supply and run of 4 of 16 sq.mm (101/0.45) PVC insulated SC unsheathed FRLS copper conductor of 1100V on 7/20 GI bearer wire for service connection mains. (For Dist Judge , Sub judge Quarters-2 EB service Main)

Supply and run of 2 of 6 sq.mm (84/0.3)PVC insulated SC Unsheathed FRLS copper Conductor of 1100V grade in 25mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron up right and end supports for mains.

Supply and run of 4 of 16 sq.mm (101/0.45)PVC insulated SC Unsheathed FRLS copper Conductorof 1100V grade in 40mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron up right and end supports for mains

Supply and Laying of 3½ x 120 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (For EB Service Group service in JM Quarters,1,2,3)

Supply and clamping of 3½ x 120 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps

Supply and fixing of brass cable gland for 3½ x 120 sq.mm PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3½ x 120 sq mm PVC LTUG Aluminium armoured cable With necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and fixing of 10A 400V, 50 Hz 3 phase 4 wire watt hour meter on suitable TW box with earth connection (For Bank, Post office, Bar Association, and Xerox)

AC Arrangements A. HIGH SIDE WORKS OUTDOOR UNIT-COOLING ONLY Supply, Installation of Air cooled Outdoor Condensing Units (ODU) with Inverter Compressor VRV unit, connected to multiple Indoor Units. The Refrigerant shall be R-410A. The Compressor to be High Performance with low noise Scroll Compressors with Variable Refrigerant Volume system connectable to multiple indoor units.

B.INDOOR UNIT Supply, Installation, Testing and Commissioning of factory assembled 4way Cassette type Indoor unit of the following capacities with matching VRF system, the unit completely tested and included factory wiring, piping, synthetic washable media pre- filter, fan section with low noise multi speed fan motor and dynamically balanced blower, coil section with DX copper coil, electronic proportional expansion valve along with pump to control the refrigrant flow rate responding to variations of the airconditioning load of the room, 360° air flow discharge, control circuit board, presence and floor sensors, auto cleaning panel, thermal protector, condensate drain pan, self diagnostics, auto-restart function, test run switch, drain pump and outer cabinet, necessary supports, vibration isolation, cordless remote control, etc., suitable for operation on 230V ± 10%, 50Hz, single phase AC supply, complete as required. The unit shall have an auto swing louver which ensures efficient air distribution which closes automatically when the unit stops. The front grille shall be easily removed for washing. The remote controller shall be able to set five steps of discharge angle. The discharge angle shall be automatically set at the same angle as the previous operation upon restart. The drain pipe can be fitted to from either left or right sides. The indoor unit and the refrigerant pipes shall be charged with dehydrated air prior to shipment from factory.

Both refrigerant lines shall be insulated from the outdoor unit to indoor unit and return air shall be through a resin net mold resistant filter. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS system.

FXFSQ125-3.0TR

FXFSQ125-4.0TR

Supply and Installation of Refnet joints / branch distributors forindoor and outdoor units.

Supply of Wireless Remote controller for cassette units.

LOW SIDE WORKS 1.PIPING Supply, installation, testing and commissioning of hard/soft drawn soft refrigerant piping. The brazing to be carried out with bleeding of nitrogen. The copper pipe to be insulated with 19 mm thick Nitrile Rubber sleeves or sheet

Supply and installation of 2C x 1.0 sqmm communication cable

Supply and fixing of 32mm dia UPVC pipe with all required accessories and suitable clamping, etc., for drain pipe connections to the indoor units, etc., as required.

Supply and providing of pipeline Nitrile rubber insulation for Refrigerant and Drain pipe lines

Supply and providing Civil concrete block for mounting the Airconditioning unit

Supply, fabrication and fixing of MS channel with supports, etc., complete as required for mounting the Airconditioning Indoor unit

R-410 A Gas Charging for VRV systems

Supply and fixing of 50mm thick Anti Vibrating rubber Pads

Supply, fabrication and fixing of grills for the Outdoor unit

Pressure testing the system, vacuumizing, leak testing, gas charging and commissioning of the above circuit.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps/ supports on wall/ floor/ ground for earth connection.

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Earthing as per the ISI specification with an earth electrode of 2.1 mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

SRK ASSOCIATESS (BID ID -1235196)