SPECIAL REPAIRS TO DAMAGED CEILING AT FMU MBI FSTC COMPLEX BUILDING NO P 49 AT NAVAL DOCKYARD PROVN OF CEMENT CONCRETE ROAD CONNECTING TO SOUTH WHARF JETTY AT NAVAL DOCKYARD ADDITION/ALTERATION AND SPECIAL REPAIR TO BLDG NO T 2 AT INS KUNJALI AND PR

Amount

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed Engr-in-Charge.

Material and labour for gypsum board false ceiling using 600 x 900 x 12 mm thick plaster of paris with gypsum binder sheet decorative type and necessary provision for concealed type light fittings, fixed on 22 gauge GI channel grid work main joist of size 50 x 25 mm spaced at 750 mm centre, secondary joist of size 75x20 mm fixed to main joists spaced 900 mm suspended to roof members using 25 x 25 x 2 mm GI angles and fasteners @ 1.2 m C/C including decorative design/pattern complete all as specified and directed Engr-in-Charge.

Material and labour for false ceiling made out of 600 x 600 x 4 to 6 mm thick ceiling board/tiles deep panel suspensor system made out of powder coated GI sheet main tee of size 23.50 x 40 x 0.63 mm and cross tee of size 23.50x23.50x0.63 mm and angle size 19x19x0.63 mm including 3 mm GI wire for suspending holts necessary washers nut/cleats/pin hook etc for securing frame work to ceiling to the snap grid including provn of necessary holes/cutting for providing light/far as required including making necessary recesses/projected pattern complete all as specified and directed Engr-in-Charge.

Material and labour for preparation applying two coats of plastic emulsion paint over a coat of primer complete all as specified and directed Engr-in-Charge.

Taking down cement plaster of any description hacking for key, racking out joints and scrubbing down with water etc to receive plaster and removing debris outside MoD land incl necessary scafolding complete all as specified and directed Engr-in-Charge.

Material and labour for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finishing using waterproofing compound the surface fair and even complete all as specified and directed Engr-in-Charge.. (cost of integral water proofing compound shall be measured seperately).

Material and labour for Rendering 5mm thick on brick work or concrete surfaces in ceiling in cement mortar 1:3 finished even and fair including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified and directed Engr-in-Charge.(Water proofing compound to be measured and paid for separately).

Material and labour for preparation of New decorated surfaces of walls and applying two coat of oil bound distemper (oil emulsion) over a coat of primer on walls complete all as specified and directed Engr-in-Charge.

Material and labour for preparation of newly plastered surfaces of wall & ceiling applying two coats of oil emlusion distemper over a coat wall care putty of 3mm thick and alkali primer complete all as specified and directed Engr-in-Charge.

Material & labour for taking down, chipping and removing the loose, spailt, damaged cement concrete, cement mortor surfaces of RCC columns, beams, walls, chajjah etc and exposing the reinforced cement , wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthening the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing 40mm thick polymer plaster (1:5:15, cement, sand, polymer) and finally finishing the surface all as specified and directed.Make :- Dr.Fixit/Sunanda/Chemestik/Fosrok as approved by GE. Note :- (New reinforcement and MS Sections will be measured and paid separately)

Replacement of steel reinforcement with TMT bars of appropriate size where 30% of cross section is reduced including dismantling of rusted steel complete all as specified and directed Engr-in-Charge.

Providing and fixing additional main steel bar or stirrups of designed diameter in various structural elements like column, beams and foundations including drilling, bending and fixing the bars with epoxy putty etc complete all as specified and directed Engr-in-Charge. (Steel provided on the basis of 1% of volume of concrete)

Material and labour for injecting Low visosity (3-5cps) high molicular weight monomer by pressure and using mechanized injector gun with accessories till nozzles refuses to accept the grout, including, mixing or material as mixing of material components (Part a&b) in the required quantities as per manufacturer's instruction by weight batching. Grouting fill the grouting gun with concrete penetrating corrosion inhibitor EPCO-KP-100/protectsil CIT or Ferogard 903. Maintain desired pressure in the gun by air compressor ; maintain the pressure at exit (2 to 3kg/Cm2) by monitoring pressure guage at exit grout the material throught prefixed nozzles in the structural elements @ 100ml per nozzle. Repeat the precess for all the nozzles and including scaffolding upto any height complete all as specified and directed Engr-in-Charge.

Supply only Integral waterproofing compound complete all as specified and directed Engr-in-Charge.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 25cm deep and getting out in hard/ dense soil including clearance of site etc complete all as specified and directed Engr-in-Charge.

Material and labour hardcore of gauge exc 63mm but n exc 100mm, deposited, spread and levelled in layers n exc 15cm thick, watered and rolled/rammed to a true surface. using broken Stone or boulders complete all as specified and directed Engr-in-Charge.

Material and labour PCC 1:4: 8 type D2 using 40mm graded stone aggregate as in foundations, filling, mass concrete complete all as specified and directed Engr-in-Charge.

Material & labour for PCC M -40 grade ready mix concrete in hard standing etc complete all as specified and directed Engr-in-Charge.

Removing excavated material beyond exc. 5 Kmupto total distance of 15km or outside of MoD land etc complete all as specified and directed Engr-in-Charge.

Forming 12mm thick expansion joints for 100mm thk concrete slab filled with pre-formed bituminous filled and top 30mm primed and sealed with sealing compound, Grede 'B' etc complete all as specified and directed Engr-in-Charge.

Material and labour MS framed work such as grills, grantings, sun shed etc with ends of bars shouldered and/or riveted or welded, or forged into spikes, framed guard bars, barred iron doors, ladders, farmed balastures, walk ways, railings, frame work of water tanks and similar work conforming to fe 290 Gde E-165 complete all as specified and directed Engr-in-Charge.

Material and labour for preparing new or perviously untreated surface of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed Engr-in-Charge.

Dismantling plain or corrugated steel/AC roof sheets any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed Engr-in-Charge.

Supply and fixing pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, chajjas, fixed with self tapping screws complete all as specified and directed Engr-in-Charge.

Supply and fixing pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, chajjas, valley gutter, ridge and fixed with crumple joint etc fixed with self tapping screws complete all as specified and directed Engr-in-Charge.

Supply and fixing for 1.50mm thick plain , galvanised mild steel sheeting in ridges , valley gutters,drip and other suitable arrangements over MS brackets Trapezoidal shape of required profile with desired slope etc complete all as specified and directed by Engr-in charge .

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed Engr-in-Charge.

Supply and fixing mild steel roof trusses (framed), trussed, purlins,crane gantries, rails and fastnings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe- 410-W- Gde E-250 quality A complete all as specified and directed Engr-in-Charge.

Taking down chowkats or frames but n exc 1.5 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and directed Engr-in-Charge.

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and directed Engr-in-Charge.

Taking down shutters of any description exc 1 sqm and n exc 2 sq.m each complete all as specified and directed Engr-in-Charge.

Supply and fixing 2nd class hard wood (sal) plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed Engr-in-Charge.

Supply and fixing 30mm thick 2nd class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. divided in to squares,with plain, chamfered or rounded , mitred and rebated sash bars,any numbers ; edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a) ; supplied and fitted to chowkhats of Second class hard wood complete all as specified and directed Engr-in-Charge.

Supply and fixing 40mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both side complete all as specified and directed Engr-in-Charge.

Supply and fixing in repair powder coated aluminium (minimum 25 micron thickness of coating) of various section as required for doors, window & partion/Ventilator etc including fixing and making the frames hinges to receive glass/wire gauge etc. Complete incl all fittings like rubber beading, clips locking arrangement, handle, tower bolt for shutter, sealant etc all as specified and as directed by Engr- in- charge.

Supply and fixing in repair aluminium grill with and including suitable aluminium anodised frame F/H section as requird manufactured by M/S Decogrill as per design No DG- 102, 7.5 mm thick all as specified and as directed by Engr- in- charge.

Supply and fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel stapple etc complete all as specified and directed Engr-in-Charge.

Supply and fixing in repairs 18/19 mm thcik prelaminated partical board exterior grade prelaminated one side with lamination and other side balancing white lamination fixed with screw to frame work cupboard etc including 6 mm thick teak wood beading all around complete all as specified and directed Engr-in-Charge.

Supply and fixing 12mm thick prelaminated medium density fibre board,interior grade, prelaminated both side with decorative choice lamination fixed with screws to aluminium frame work complete all as specified and directed Engr-in-Charge.

Supply and fixing 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts complete all as specified and directed Engr-in-Charge.

Supply and fixing for aluminium anodized barrel tower bolts 150 mm of extruded section and fixed complete all as specified and directed Engr-in-Charge.

Supply and fixing 150 mm size aluminium alloy handles, febricated type extruded section, ISI marked complete all as specified and directed Engr-in-Charge.

Supply and fixing butt hinges 100 mm mild steel hinges medium weight and fixed complete all as specified and directed Engr-in-Charge.

Supply and fixing butt hinges 100 mm stainless steel hinges medium weight and fixed complete all as specified and directed Engr-in-Charge.

Supply and fixing 150mm sizes brass handle cast type polished bright complete all as specified and directed Engr-in-Charge.

Material and labour for MS flat for hold fast. Conforming to Fe-290 Gde E-165 complete all as specified and directed Engr-in-Charge.

Supply and fixing in repairs 125 mm long floor door stopper of aluminium door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed Engr-in-Charge.

Material and labour 0.9mm thick decorative texture finish laminate type 1 , of surface finish colour and pattern as approved fixed with adhesive as per makers instruction complete all as specified and directed Engr-in-Charge.

Material and labour for mild steel Hand mild steel rails, half round or other stock section , nosing to steps in cluding embeding in concrete and screwing etc. wind ties for roof including securing bolts and similar work conforming to Fe 290 Gde E 165 complete all as specified and directed Engr-in-Charge.

Material and labour Plastering 15mm thick in CM 1:6 on brick surfaces, finished with Neeru finish on walls complete all as specified and directed Engr-in-Charge.

Material and labour rendering 20mm thick in two coats(15mm inner coat 5mm finishingcoat) on brick work or concrete surfaces in cement mortar 1:4 finished even and fair including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions including necessary scafolding for high rise bldgs etc all as specified and directed. (Water proofing compound to be measured and paid for separately).

Material and labour for chipping, removing carefully concrete work by low impact hammer breakar without damaging the structure & cleaning and disposal of debries out side the premises etc complete as directed by Engr-in-Charge, hard concrete should not be removed by force including necessary scafolding for high rise bldgs etc complete all as specified and directed Engr-in-Charge.

Material and labour for clean existing reinforcement with wire/rotary wire brush, making the surfaces free from loose material dirt etc complete applying two coats of alkaline rust converting primer FEOVERT confirming to ASTM-B-117, on the rebars, including cleaning the reinforcement wire brushing to remover loose rust spalls with time interval of 6 hour between the coats and applying protective coating IPNET-RB complete all as specified and directed Engr-in-Charge.

Material and labour for replacement of steel reinforcement with TMT bars of appropriate size where 20% of cross section is reduced including dismantling of rusted steel including application of rust converter FEOVERT and applying protective coating IPNET-RB complete all as specified and directed Engr-in-Charge.

Material and labour for carry out application of Bi-polar migratory corrosion inhibitor EPCO-KP-100/Protectsil CIT/Ferogard 903 on concrete surface (This inhibitor shall have migratory kind of properly which permits the material to migrate to a vertical extent of 100 mm through pores of concrete, inhibiting the corrosion and de-passivating the Electro-chemical reaction. It should have properly to attack anode as well as cathode, which is purely alkaline in nature (pH-9.5) so it has not carcinogen activity with concrete complete all as specified and directed Engr-in-Charge.

Material and labour for providing and applying structural grade EPIBOND-21-LP prior to application of any type of mortar plaster confirming to ASTM-C-882-91 (Arizona Slant Shear Test) to ensure bond between old concrete and new concrete complete all as specified and directed Engr-in-Charge.

Material and labour for Building up the profile of structural members by using latex additives(MONOBOND) modified air cured mortar system (Polymer modified mortar) (1:5:15 = 1 monobond-5Cement-15 sand) -in damaged areas in 30mm thickness including leveling profliling and scaffolding for high rise buildings etc complete all as specified and directed Engr-in-Charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles and disposing off complete all as specified and directed Engr-in-Charge.

Material and labour brick work with sub class B bricks straight or curved on plan exceeding 6 m mean radius built in CM 1:6 complete all as specified and directed Engr-in-Charge.

All as per item No 60 above but except bricks complete all as specified and directed Engr-in-Charge.

Material and labour for brick work with sub class 'B' bricks straight or curved on plans to any radius in half brick thick walls built in cm (1:4) complete all as specified and directed Engr-in-Charge.

Supply and fixing in repair 12mm thick, toughened glass for door shutters, partitions, shelves etc with and including fitting and fixtures such as glass handles ss studs, fittings for door pivots etc complete all as specified and directed Engr-in-Charge.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed Engr-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed Engr-in-Charge.

Material and labour providing plain cement concrete type B-1, 1:2:4 (using 20 mm graded stone agg) as in lintels upto 1.5 M clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, roof kerbs, water troughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed Engr-in-Charge.

Material and labour for RCC 1:1.5:3 nominal mix (20mm graded stone agg) as in beams, cantilevers, bressumers, lintels over 1.5 m span complete all as specified and directed Engr-in-Charge.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings , girders, bressummers, lintels, cantilevers, shelves including supports overhangs, etc also splays between floors and beams etc rough finished surface of concrete complete all as specified and directed Engr-in-Charge.

Material and labour mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed Engr-in-Charge.

All as per srl item No. 69 above but 5mm dia and over including 10mm dia in stirrups, spaces and binders etc complete all as specified and directed Engr-in-Charge.

Dismantling stone slab and tiles of of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc complete all as specified and directed Engr-in-Charge.

Material and labour for machine cut kota stone slab flooring 18 to 20 mm thick as in steps, landings, floors etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing,mirror polishing incl making 02 Nos grooves in steps over & incl 20 mm thick screed bed in cement mortar 1:4 complete all as specified and directed Engr-in-Charge.

Material and labour 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed Engr-in-Charge.

Rounding to edges of stone slabs on edge, such as in steps, cooking platform and making grooves for lining and other similar work complete all as specified and directed Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and disposing the rubbish to the out side of MoD land complete all as specified and directed Engr-in-Charge.

Taking down PVC wastage and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and directed Engr-in-Charge.

Supply and fixing 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed Engr-in-Charge.

Supply and fixing 110 mm bore PVC (SWR) bends any radius complete all as specified and directed Engr-in-Charge.

Material and labour for preparation of old painted steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint with necessary scaffolding for high rise bldgs etc complete all as specified and directed Engr-in-Charge.

Complete removal of existing treatment on wall surfaces by scrapping, washing & rubbing down with water and applying two coats of oil bound distemper over a coat Chalk whiting, on plastered surfaces complete all as specified and directed Engr-in-Charge.

Material and labour for preparation of old decorated surfaces of wall and applying one coat of oil emulsion distemper complete all as specified and directed Engr-in-Charge.

Material and labour for applying 1 to 2 mm thick wall care putty for making the surface even & smooth complete all as specified and directed Engr-in-Charge.

Material and labour for preparation of old decorated surfaces of ceiling and applying one coat of oil emulsion distemper complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of wall, soffits, facia roof and applying two coats of weather proof acrylic based paint (100% acrylic) over one coat of cement based primer with necesssary scaffolding for high rise blds etc complete all as specified and directed Engr-in-Charge.

Material and labour preparation of old decorated surfaces of walls, soffits, roof facia and applying one coat of weather proof acrylic based paint (100% acrylic) with necessary scaffolding for high rise bldgs etc complete all as specified and directed Engr-in-Charge.

Material and labour for preparation of newly wooden surfaes of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer incl preparation of surfaces complete all as specified and directed Engr-in-Charge.

Material and labour for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint including external window with necessary scaffolding for high rise bldgs complete all as specified and directed Engr-in-Charge.

Supply and fixing in repairs door closer hydraulically regulated, designation No 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed complete all as specified and directed Engr-in-Charge.

Supply and fixing 4mm thick bakelite sheet with decoratie choice laminated on both side complete all as specified and directed Engr-in-Charge.

Supply and fixing double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium ally sheet foundation box, main body with stainless steel cover, governing pivot made of bras, other parts made of mild steel heavy duty and fixed complete all as specified and directed Engr-in-Charge.

Material and labour for point wiring with FRLS PVC insulated unsheathed multi stranded copper conductor cable of 2.5 sqmm size 1100 volts grade drawn through and including non metalic rigid PVC casing and caping not less than 25mm width with all accessories fixed on wall including FRLS PVC insulated, unsheathed multistranded copper onductor cable of size 2.5 sqmm as earth continuty conductor connecting to common earth dolly and PVC moulded box ISI marked for having the switches, switch sockets regulator etc complete all as specified and directed Engr-in-Charge. for following:-

One 5pin, 15 Amps switch socket combination on same board complete all as specified and directed Engr-in-Charge.

Material and labour for submain wiring with 2 runs of 4 sqmm and 1 run of 4 sqmm FRLS PVC insulated unsheathed multistranded copper conductor cable with proper colour coding drawn through and including non metalic PVC casing & caping not less than 25mm width ISI marked with all accessories like PVC elbow, PVC Tee etc fixed on wall complete including connecting up complete all as specified and directed Engr-in-Charge.

Material and labour for submain wiring with 2 runs of 6 sqmm and 1 run of 6 sqmm FRLS PVC insulated unsheathed multistranded copper conductor cable with proper colour coding drawn through and including non metalic PVC casing & caping not less than 25mm width ISI marked with all accessories like PVC elbow, PVC Tee etc fixed on wall complete including connecting up complete all as specified and directed Engr-in-Charge.

Supply and fixing LED light fitting 1x20W, 230 V, 4 feet surface monted box type, T- 5 LED batten, integrated type etc complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round block-02 Nos and connecting up with twin core twisted flexible copper conductor cable with suitable size and all as directed by Engr-in-Charge.

Supply and fix modular socket 16 Amps 2/3 pin 240 volts Ac combined 2 module complete all as specified and directed Engr-in-Charge.

Supply and fix ceiling rose surface bakelite three terminal of size 60x50 mm,240 Volts AC complete all as specified and directed Engr-in-Charge.

Supply and fixing in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. Make -Legrand cat No 507610 or equivalent in Havells/HPL (Note : The cost of removing old wooden box and making good of surface i.e. brick work, plastering etc is included in quated rate)

Supply , fixing, testing in repairs of JEF ECO SAFE Maintenance Free Grounding Solution set comprising of High tensile low carbon steel rod of 3 Mts length & 25 mm dia with 250 micron ( averaSchneider ) molecularly bonded copper on the outer surface to confirm with requirements of UL467 along with Back-fill compound strictly be a Carbon based conductive concrete type which has a resistivity of less than 0.12 Ohm Mtr as per Clause 14.5D of IEEE : 80 standard. Back-fill compound should be electronically conductive ( Like in metals ) and should not depend on moisture for conduction. JEF Powerfill Loresco compound shall be supplied in 50 Pound Bag. ( 1 Bag of 50 Pounds required per earthing set). Back-fill comound should be environment friendly, should solidify when mixed with water and set like concrete and should not leach / diffuse into the ground. A suitable earth terminaton clamp should also be supplied along with the set alongwith earth pit weatherproof incl complete all as specified and directed Engr-in-Charge. Note : Back-fill compund shall not be mixed with any soil while pouring in the bore hole.

Supply and fix sheet metal enclosure with 2 pin and earth plug and socket complete with single pole MCB of 20 Amps complete all as specified and directed Engr-in-Charge.

Taking down carefully old U/S point wiring copper/Aluminum (light/ fan /sockets/power) complete with switches, sockets, fan regulators, ceiling roses, lamp holders, brackets, ,removing material to store for keeping in safe custody and making good to disturbed surfaces as directed by Engineer-in-Charge

Material and labour for point wiring with FRLS PVC insulated, un-sheathed, multi stranded copper conductor cable of 1.5sqmm size, 1100volts, drawn through and including non metalic rigid PVC casing and caping not less than 25mm with all accessories fixed on wall//ceiling/truss including FRLS PVC insulated, unsheathed, multi stranded copper conductor cable of 1.5sqmm size as earth continuty conductor connected to common earth dolly including required numbers and size of PVC Modular box with cover plate fixed on wall for fixing the switches, switch sockets,sockets, regulators etc complete all as specified for:- NOTE: a) Colour coding shall be followed as given below:- i) Phase - Red/Yellow/Blue ii) Neutral - Black iii) Earth - Green b) Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit. (c) Make of wire :- Havells/ Finolex/ Plaza/Gloster/Polycab. (d) Make of PVC casing capping :- Precision/ pesto plast / National/Plaza

One light point controlled by one 5A switch

One Fan/Exhaust fan point controlled by one 5A switch

One 5A flush type switch socket point on same board board

One 5A flush type switch socket point on independent board

Material and labour for point wiring complete with proper colour coding using PVC insulated unsheathed multistranded copper conductor cable 2.5 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 2.5sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module complete for One 5 pin, 15A switch socket combination on the independent board complete all as specified and directed Engr-in-Charge

Material and labour for point wiring complete with proper clour coding using PVC insulated unsheathed multistranded copper conductor cable 4.0 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 4.0sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module complete necessary electric connection for each workstation point comprising of 03 Nos 6A sockets and 01 No 15A socket on same board complete all as specified and directed Engr-in-Charge. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Switch socket measured & paid separately.

Supply and fixing ceiling rose surface bakelite 65 x 50mm, flush type, 3 terminals complete all as specified and directed Engr-in-Charge.

Supply and fixing modular switch 1 way 6A complete all as specified and directed Engr-in-Charge.

Supply and fixing modular switch 1 way 15A/16A complete all as specified and directed Engr-in-Charge.

Supply and fixing modular socket, 6A - 2/3 pin combined 2 modules complete all as specified and directed Engr-in-Charge.

Supply and fixing modular switch socket combination 16A,3 module complete all as specified and directed Engr-in-Charge.

Supply and fixing for modular fan regulator fan step regulator, 120W - 2 modular step type complete all as specified and directed Engr-in-Charge.

Supply and fixing in repair new generation ultra slim recessed LED 2X2 Luminaire 36 watt, CRCA powder coated body and high translucent diffuser provides high quality ecomonic energy saving lighting Suitable for 600 x 600 mm modular/POP/Gypsum ceiling. Make : C&S/Havells/Philips/Bajaj/Shakti cat No SZRELMX040 or as approved by GE.

Supply and fixing LED 90W Street/building security light fittings with high pressure die cast housing with toughened glass and individual LED with secondary optics and IP66 protection complete all as specified and directed by EIC. Make : C&S/Havells/Philips/Bajaj/Shakti Cat No SZPSLPM090 or as approved by GE

Supply and fix in replacement MS arms bracket 30 degree bend, 1.5mtr long for mounting one in nos street light fitting including clamps / nut / bolts & washer to brace the same properly with duly painted in synthetic enamel paint of two coat in silver colour complete all as specified and directed by the Engr-in-Charge.

Supply and fixing in repair sheet metal enclosure TPN DB VTPN 8 Way,415V with 250A copper busbar, double door type IP-54, IK-09 protection suitable for housing MCCB 100Amp 4 pole all as specified and directed by EIC. Note : DBs shall be concealed in wall where ever posible including making good the surface to match with surrounding.

Supply and fixing in repair MCB DB double door SPN 8 Way with 200 Amps rated copper bus bar, IP 54, IK 09 suitable for flush mounting and surface mounting complete etc complete all as specified and directed by the Engr-in-Charge.

Supply and fixing in repairs of 0.71mm thick Aluminium sheet cover, alloy 31000 H4 in ridges, Hips vally gutter including suitable size of revits/nut bolts complete bending, shaping, drilling, cutting notching and complete all as specified and directed by the Engr-in-Charge.

Supply and fixing in repair of in repair of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20A complete all as specified and directed by the Engr-in-Charge.

Supply and fixing MCB SP 6-32 Amps,10KA, 'C' curve complete all as specified and directed by the Engr-in-Charge.

Supply and fixing MCB SPN 40 Amps,10KA , 'C' curve complete all as specified and directed by the Engr-in-Charge.

Supply and fixing MCCB FP 160 Amps,16KA, complete all as specified and directed.

Material and labour for concealed sub-main wiring with 2 runs of 4.0sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC casing caping not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 4.0sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red/yellow/Blue (ii) Neutral - Black (iii) Earth - green

Material and labour for sub-main wiring with 2 runs of 10.0sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and iincluding non metalic rigid PVC casing and caping not less than 25mm with all accessories fixed on wall//ceiling/truss etc as required, including one run of 10.0sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Supply and fixing Ceiling fan ( BLDC) 5 Star Rating 1200mm sweep , suitable for operation on 230 / 240 V. 50 Hz, single phase, A.C, supply complete with electronic type regulator including connecting up with 3 core flexible cord of size 23/0.0076mm from ceiling rose to fan complete all as specified and directed by the Engr-in-Charge.

Material and labour for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to DBs or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed by the Engr-in-Charge.

Disconnecting & taking down old Unservicable cable & Supply and lay in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 120 sq mm 3½ core complete all as specified and directed by Engr-in-Charge.

Material and labour for 25x4mm GI earth continuity conductor or main earthing lead fixed to wall or buried in ground or drawn in conduit/ pipe or fixed to transformer/panel body complete all as specified and directed by the Engr-in-Charge.

Material and labour GI tube light grade 80 mm bore laid in trenches or fixed on wall, floor or on pole with MS flat iron camp with bolts, nuts and washer of suitable size for cable protection complete all as specified and directed by the Engr-in-Charge.

Supply, Installation, Testing & Commisioning of silent Diesel Engine driven generating set 415 volts, 3 phase 4 wire, engine as per IS:10001/ 10002 and Alternator as per IS: 13364 complete with relay panel and switch gears for automatic starting on main failure, control panel having meter and sound proof canopy as per CPCB norms and foundation etc. of capacity upto 40 KVA with AMF panel including alongwith RECD complete all as specified and directed by the Engr-in-Charge. Note :- Rate of necessary foundation for DG set and AMF panel shall be deemed to e included in quoted rate.

Supply, Installation, Testing & Commisioning of silent Diesel Engine driven generating set 415 volts, 3 phase 4 wire, engine as per IS:10001/ 10002 and Alternator as per IS: 13364 complete with relay panel and switch gears for automatic starting on main failure, control panel having meter and sound proof canopy as per CPCB norms and foundation etc. of capacity upto 20 KVA with AMF panel including alongwith RECD complete all as specified and directed by the Engr-in-Charge. Rate of necessary foundation for DG set and AMF panel shall be deemed to e included in quoted rate.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 120 sqmm 3.5 core complete all as specified and directed by the Engr-in-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 sqmm 3.5 core complete all as specified and directed by the Engr-in-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core complete all as specified and directed by the Engr-in-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm 4 core complete all as specified and directed by the Engr-in-Charge.

Supply of JEF ECO SAFE Maintenance Free Grounding Solution set comprising of High tensile low carbon steel rod of 3 Mts length & 32 mm dia with 250 micron ( average ) molecularly bonded copper on the outer surface to confirm with requirements of UL467 along with Back-fill compound strictly be a Carbon based conductive concrete type which has a resistivity of less than 0.12 Ohm Mtr as per Clause 14.5D of IEEE : 80 standard. Back-fill compound should be electronically conductive ( Like in metals ) and should not depend on moisture for conduction. JEF ECO SAFE compound shall be supplied in 50 Pound Bag. ( 1 Bag required per earthing set). Back-fill comound should be environment friendly, should solidify when mixed with water and set like concrete and should not leach / diffuse into the ground. A suitable earth terminaton clamp should also be supplied along with the set incl Supply of Eco Friendly weather proof High Density Polyethylene Earth Pit Chamber Note : Back-fill compund shall not be mixed with any soil while pouring in the bore hole.

Material and labour for earth continuity conductor or main earthing lead of size 32mm x 6mm GI strip fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated or situation etc. duly screwed / saddled as required at site and connecting up complete all as specified and directed by the Engr-in-Charge.

Supply, fabrication, installation, testing & commissioning of LT Panel board / Feeder piller box, in door type, dust and vermin proof, made out of 3.15 mm thick CRCA sheet, front & back openable doors having vertical COPPER bus bar of capacity 500 amps for phases and for neutral including powder coated painting, internal wiring with suitable size of stranded copper conductor cable, PCC foundation, supporting channels,cable termination,cable gland etc complete at INS TRATA. INCOMER a) MCCB 125 Amps 4pole,16 KA,Thermal magnetic - 1 Nos (Incomer) OUTGOING c) MCCB, 4 pole 63Amps,16KA,Thermal magnetic - 4Nos (Out going) f) VAF meter class 1with CT's - 1 No g) indication lamps (R,Y,B) LED type - 1 set

Supply, fabrication, installation, testing & commissioning of Feeder piller box for looping of cables , in door type, dust and vermin proof, made out of 3.15mm thick CRCA sheet, front & back openable doors having vertical copper bus bar of capacity 100 amps for phases and for neutral including powder coated painting, PCC foundation, supporting channels,cable termination,cable gland etc complete at jetty/casin including taking down old panel complete all as specified and directed by the Engr-in-Charge.

Excavation in trenches n exc1.5m wide and n exc in depth for laying of cables and getting out in loose/soft soil complete all as specified and directed by the Engr-in-Charge.

Returing filling in including spreading, levelling watering and well ramming in layers not exc 25cm complete all as specified and directed by the Engr-in-Charge.

Removing excavated material n exc 50cm and deposting where directed at a level n exc 1.5m above the starting point complete all as specified and directed by the Engr-in-Charge.

Material and labour for sand filling in trenches fine dry sand as sand cushioning to cable 8 cm before laying of cables and 15 cm after laying cable which shall be punned down to 10 cm complete all as specified and directed by the Engr-in-Charge. . (Note : Only punned down thickness shall be measured and paid)

Supply and layingreinforceced precast concrete cable cover, class LV type , I, flat size 250mmx150mmx40mm laid across the cable complete all as specified and directed by the Engr-in-Charge.

Material and labour for GI pipe light grade 100mm dia for protection of UG cable crossing of nalha/bridge/road etc complete all as specified and directed by the Engr-in-Charge.

Material and labour cement concrete in 1:2:4 type B1 using 20mm grade stone aggregate for road cutting/pole couping exposed surfaced and fair and even finishing with out using any extra cement etc complete all as specified and directed incl Material and labour for road cutting .

Supply and fixing in repair of MS/ GI hot dip/ powder coated perforated GI cable tray sheet thickness not less than 1.6mm ,50 mm height of tray and width not less than 450mm to be fixed on any wall (brick/stone) vertically/horizontally ,including tray cover of thickness not less than 2.00mm,including all accessories complete bending, shaping, drilling, welding, cutting and including all fixing arrangement such as suitable size of nuts, bolts, coupler plates etc complete all as specified and directed by Engr-in-charge.

Material and labour Mild steel for rolled mild steel section as in main and cross beam, hip and jack rafter, purlins where connected to common rafters and running rails and guides for sliding door, fixed with angles cleats or other connecting plates confirming to grade Fe 290, Gde E-165 complete all as specified and directed by Engr-in-charge.

Excavation in post holes in hard/dense soil (or smilar holes) each n exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance n exc 50m and making good surface complete all as specified and directed by the Engr-in-Charge

Material and labour for PCC 1:2:4 type B-1, (using 20mm graded aggregate) as in foundation, filling mass concrete ,grouting of angle posts, pillars etc including necessary form work complete all as specified and directed by the Engr-in-Charge

Supply and fixing for rolled mild steel work such as in compound girders and stanchion, lattice girders, aerial masts, staging for water tanks and the like including caps, bases,splices etc. built up from two or more beam or channel section or angles with plates, including all lattice bars stiffeners, gusset pates etcand similar work conforming to Fe 410- W-(Gde-E-250) quality A complete all as specified and directed by the Engr-in-Charge

Material and labour for brass letters of figure (block, roman, Italic or Indian) and crests(navy) etc not exceeding 30 cm high , with 1 to 2mm thick brass letters . All as specified and as directed by the Engr-in Charge

Supply and fixing for 3 mm thick aluminium composite panel cladding plain of approved colour/shade to beam/column/slab incircular/celing,rectangular shape inbcluding cutting, notching, bending to shape as required jointing with silicon gel of approved colour & aluminum tubular hallow section 25 x 25 mm not exceeding 900 mm C/C on exceeding column/beam/slab to hold APC cladding etc (Note : colour/pattern of ACP sheet shall be given by GE).

Material and labour for concealed point wiring complete with 1.5 Sq.mm single core multistranded PVC insulated & unsheathed copper conductors cable 1100 volts FRLS grade ISI make and drawn through & including PVC Casing Capping with Accessories fixed on wall/ceiling/truss etc with PVC non metallic ISI make terminal boxes fixed on wall including one PVC insulated & unsheathed multistranded copper conductor 1.5 Sq. mm as earth continuity conductor connected to common earth dolly including modular box and cover plate all as specified.Notes: a) Colour coding shall be followed as given below:- i) Phase - Red ii) Neutral - Black iii) Earth - Green b) Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit.

One light point point controlled by one 5A switch

One 5A flush type switch socket point on same board board

One 5A flush type switch socket point on independent board

Material and labour for concealed point wiring complete with 2.5 Sq.mm single core multistranded PVC insulated & unsheathed copper conductors cable 1100 volts FRLS grade ISI make drawn through & including PVC Conduit with Accessories fixed on wall/ceiling/truss etc with metallic ISI make terminal boxes fix on wall including one PVC insulated & unsheathed multistranded copper conductor 2.5 Sq. mm as earth continuity conductor connected to common earth dolly for single board having 1 x15 Amp switch socket point for independent board complete including required size and numbers moduler box and cover plate all as specified & directed. Notes:- a) Colour coding shall be followed as given below:- i) Phase - Red ii) Neutral - Black iii) Earth - Green

Material and labour for concealed point wiring complete with proper colour coding using PVC insulated unsheathed multistranded copper conductor cable 4.0 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm PVC Conduit with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 2.5sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including required number and size of modular box with cover plate frame in any module complete necessary electric connection for each workstation point comprising of 02 Nos 6A sockets and 01 No 15A socket on same board complete all as specified and directed. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Switch socket measured & paid separately.

Supply and fixing in repair new generation walll/surface mounted 1x 20W LED batten fitting, 4 feet surface mounted provides high quality ecomonic energy saving lighting complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round block-02 Nos including connecting up with twin core twisted flexible copper conductor cable with suitable size and all as directed by Engr-in-Charge. Make : C&S Cat Part No- LT4F20WLEDT8/WDI)/Wipro//Bajaj or as approved by GE.

Supply and fixing in repair of LED down light 18 W round panel mounted, opaque diffuser complete with acessories high quality ecomonic energy saving lighting Suitable for 600 x 600 mm modular/POP/Gypsum ceiling complete all as specified and directed by the Engr-in-Charge

Supply and fixing wall mounted fan, 400 mm sweep, single phase oscillating complete fixing accessories required at site and making good the distrubed surface & connection copper cable from ceiling rose to exhust fan complete all as specified and directed by EIC. Make: model No Havells (D'zire')/Usha/CG/Orient or as approved by GE.

Supply and fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete suitable for one single pole MCB 20A complete all as specified and directed by the Engr-in-Charge

Material and labour for concealed sub-main wiring with 2 runs of 2.5sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC casing & caping not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 2.5sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material and labour for sub-main wiring with 4 runs of 10.0sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC conduit not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 10.0sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Supply and fixing MCB SPN 40 to 63 Amps,10KA , 'C' curve complete all as specified and directed by the Engr-in-Charge

Supply and lay in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded copper conductor of size 35 sq mm 3.5 core. laid in trench/ duct / along pole/wall etc including making connection complete all as directed. Note : 1. The cost of thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it.

R J ENTERPRISES

ROHIT CONSTRUCTION